FCC/IC - Terms of Use for Pilz Manuals PSEN slock (p) 2014-11-03, R2.0
Page 1 of 1
USA/Canada
FCC ID: VT8-PSENSLP IC: 7482A-PSENSLP FCC/IC-Requirements: This product complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standards. Operation is subject to the following two conditions: 1) this product may not cause harmful interference, and 2) this product must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this product not expressly approved by Pilz may void the FCC authorization to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Le présent produit est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) le produit ne doit pas produire de brouillage, et (2) l'utilisateur de le produit doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
2 nov. 2015 - (2) this device must accept any interference received, including ... cause harmful interference to radio or television reception, which can be ...
Make sure the power door locks to confirm you are in the programming mode. 7) Press the LOCK ... button to confirm that the system has accepted the remote.
Important Note: To comply with the FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjuncti
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or mor
Programming Instructions: 1) Turn vehicle ignition key to ON position, without starting engine (Key-On Engine-Off - Position "1"). 2) Insert Programmer into OBD connector DLC port ( - located under steering column, near pedals). Green LED should turn
The term âIC:â before the radio certification number only signifies that Industry Canada technical specifications were met. FCC ID: MRXTMS5. IC: 2546A-TMS5.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and. (2) this device must accept any interference received, including interference that may
continued FCC and Industry Canada regulatory compliance. ... This device complies with Part 15 of the FCC Rules and with Licence exempt RSS standards of.
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. WARNING: Changes or modifications not expressively approved by the party responsible for co
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installati
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the rece
3 nov. 2014 - This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction ...
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will n
The power door locks will cycle when you have successfully entered ... If programming has failed, repeat this procedure from the beginning. ... Changes or modifications not expressly approved by Dorman Products Inc. could void the user's ...
Programming Instructions: 1) Turn vehicle ignition key to ON position, without starting engine (Key-On Engine-Off - Position "1"). 2) Insert Programmer into OBD ...
19) When last key fob is programmed with the ignition OFF, remove and ... aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
If Green LED is not on, you may remove the Programmer and try again. 3) A Buzzer sounds for 1 second Indicating ready state for learning sequence - Press the ...
If Green LED is not on, you may remove the Programmer and try again. 3) A Buzzer sounds for 1 second Indicating ready state for learning sequence - Press the ...
Programming Instructions: 1) Turn Hazard lights ON (Located in upper center counsel. 2) Insert Programmer into OBD/ DLC connector & programmer will beep ...