The power door locks will cycle when you have successfully entered ... If programming has failed, repeat this procedure from the beginning. ... Changes or modifications not expressly approved by Dorman Products Inc. could void the user's ...
ALL KEY FOBS MUST BE PRESENT AND REPROGRAMMED WHEN PROGRAMMING NEW FOBS Programming Instructions: 1. Open & unlock driver door. 2. Within 5 seconds, insert and remove the key in the ignition 2 times. (Do not turn on) 3. Close and open driver door 2 times. 4. Insert and remove the key in the ignition. 5. Close and open driver door 2 times. 6. Close the driver door. 7. Turn the key to the on position (without cranking ), and then turn off and remove the key from the ignition. 8. The power door locks will cycle when you have successfully entered programming mode. 9. Press lock & unlock buttons simultaneously for 1 second. Press unlock button for 2 seconds. Door locks will cycle 1 time to confirm successful programming. Repeat this step to program all additional remotes. 10. Open the driver door and test all remotes. If programming has failed, repeat this procedure from the beginning.
FCC WARNING Statement 15.19(a)(3): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Dorman Products Inc. could void the user’s authority to operate the equipment.
ALL KEY FOBS MUST BE PRESENT AND REPROGRAMMED WHEN PROGRAMMING NEW FOBS
IC WARNING This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. FVIN: 6399137IC MISE EN GARDE IC- Le terme IC avant le numero de dertification/enregistrement signifie seulement que les specifications techniques d’Industrie Canada ont ete rencontrees. Le fonctionnement est sujet aux deux conditions suivantes: (1) cet appareil ne doit pas causer d’interference, et (2) cet appareil doit pouvoir accepter toute intergerence recue, incluant l’interference qui peut engendrer un fonctionnement non desire de l’appareil.
ALL KEY FOBS MUST BE PRESENT AND REPROGRAMMED WHEN PROGRAMMING NEW FOBS
Programming Instructions: 1) Turn vehicle ignition key to ON position, without starting engine (Key-On Engine-Off - Position "1"). 2) Insert Programmer into OBD connector DLC port ( - located under steering column, near pedals). Green LED should turn
Make sure the power door locks to confirm you are in the programming mode. 7) Press the LOCK ... button to confirm that the system has accepted the remote.
device, however, is less that the electromagnetic energy emitted by other wireless devices such as mobile phones. The headset operates within the guidelines ...
Do not attempt to charge your headset with anything other than the AC adapter provided. The use of any other types may ... Important: Please refer to the user manual for a description of the charging status indicator lights. Some headsets ..... carga
BATTERY INSTALL : (Fig.D&E)Locate and remove the locking screw on the battery door on the back of the controller with a phillipshead screw driver. Open the cover of battery case, insert 3 AAA batteries in correct polarity. Close the battery cover and
product, as this may cause short circuits which could result in a fire or electric shock. ⢠None of the ... dealers or service centers may open the product. If any parts ...
18 juil. 2016 - may lead to the violation of FCC/IC limit and is prohibited. Installation procedure. Please refer to user's manual for the detail. w Warning: Please carefully select the installation position and make sure that the final output power
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will n
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
If Green LED is not on, you may remove the Programmer and try again. 3) A Buzzer sounds for 1 second Indicating ready state for learning sequence - Press the ...
Programming Instructions: 1) Turn vehicle ignition key to ON position, without starting engine (Key-On Engine-Off - Position "1"). 2) Insert Programmer into OBD ...
19) When last key fob is programmed with the ignition OFF, remove and ... aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
If Green LED is not on, you may remove the Programmer and try again. 3) A Buzzer sounds for 1 second Indicating ready state for learning sequence - Press the ...
Programming Instructions: 1) Turn Hazard lights ON (Located in upper center counsel. 2) Insert Programmer into OBD/ DLC connector & programmer will beep ...
you will see the message âRemote Key Learning Activeâ in the Driver Information Center. ... 6) Repeat procedure for all remotes that are not properly working.
Le present appareil est conforme aux CNR d'Industrie Canada app licables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et. (2) l'utilisateur de l
Google Playâ¢. Google Chromeâ¢. Google Play is a trademark of Google Inc. The Google Play store allows you to download apps, music, movies, and games ...
U.S.. FCC Notices. FCC ID: BKMAE-H714RX. Contains FCC ID: BKMAE-E207. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device mu
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or ... For telecommunication type connectors and terminals not used for connectio
When end-user instructions are required, as in the case of this product, the ... manual to ensure continued FCC and Industry Canada regulatory compliance.
14 juil. 2014 - Pick the Local Package Directory (this is the download cache directory). 5. ... Confidential. 9-1. Run normal F/W. æå½±çç·¨è 19. Open OS terminal and set USB comport (reference to page9 ), set baud- rate as 115200 off off ... Th
power off. Play/pause music. Tap the Multi-function button. Answer/end call ... Activate Siri/Google. Now/Cortana. Tap the Voice button, when not on a call.
