Important Note: To comply with the FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Note importante: Pour se ...
Important Note: To comply with the FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
Note importante: Pour se conformer aux exigences de conformité d'exposition FCC / RF IC, une distance de séparation d'au moins 20 cm doit être maintenue entre l'antenne de cet appareil et toutes les personnes. Ce dispositif ne doit pas être co-localisées ou opérant en conjonction avec tout autre antenne ou transmetteur.
Nota Importante: Para cumplir con los requisitos de exposición de la FCC / IC RF, una distancia de separación de al menos 20 cm debe mantenerse entre la antena de este dispositivo y las personas. Este dispositivo no debe ubicarse ni utilizarse junto con ninguna otra antena o transmisor.
2 nov. 2015 - (2) this device must accept any interference received, including ... cause harmful interference to radio or television reception, which can be ...
Important Note: To comply with the FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the ...
Apple Confidential. iPad RF Exposure information. iPad has been tested and meets applicable limits for radio frequency. (RF) exposure. Specific Absorption Rate (SAR) refers to the rate at which the body absorbs RF energy. The SAR limit is 1.6 watts p
Compliance Statement (Part15.19). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may ...
Make sure the power door locks to confirm you are in the programming mode. 7) Press the LOCK ... button to confirm that the system has accepted the remote.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or mor
Programming Instructions: 1) Turn vehicle ignition key to ON position, without starting engine (Key-On Engine-Off - Position "1"). 2) Insert Programmer into OBD connector DLC port ( - located under steering column, near pedals). Green LED should turn
The term âIC:â before the radio certification number only signifies that Industry Canada technical specifications were met. FCC ID: MRXTMS5. IC: 2546A-TMS5.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and. (2) this device must accept any interference received, including interference that may
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouil
continued FCC and Industry Canada regulatory compliance. ... This device complies with Part 15 of the FCC Rules and with Licence exempt RSS standards of.
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. WARNING: Changes or modifications not expressively approved by the party responsible for co
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installati
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the rece
3 mai 2017 - However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example
The device has been evaluated to meet general RF exposure requirement. The device can be usedin portable exposure condition without restriction. L'appareil ...
exposure compliance. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter. The portable device is designed ...
is subject to the following two conditions: (1) The devices may not cause ... not emit RF field in excess of Health Canada limits for the general population. Consult ...