COMTECH TECHNOLOGY CO., LTD. FM2350TSIMP 1. SCOPE 3.Test

Aug 15, 2001 - Test Conditions. 3-1. Testing ambient conditions. Defined as temperature of ... Unit setting conditions. (1). Picture --10 step wave signal ...
100KB taille 2 téléchargements 269 vues
COMTECH TECHNOLOGY CO., LTD.

FM2350TSIMP

1. SCOPE This specification outlines the pertinent electrical requirements of the RF output modulator which converts the FM video and FM audio signal into the RF signal for television standard transmission system.

2.GENERAL SPECIFICATIONS 2-1. Output frequency

2350~2420MHz (I2C PLL controller from outside)

2-2. Supply voltage

B1 9.0+/-0.5V B2 5V Max B3 -1.0~-1.6V

2-3. Consumption current

B1 95+/-10mA B2 500mA Max (B3-1.2V)

2-4. Operation and storage 2-5 Conditions for guarantee

Temperature 0-50oC Humidity 85% or less

3.Test Conditions 3-1. Testing ambient conditions Defined as temperature of 25+/-2oC and humidity of 65+/-5% RH. Note: That temperatures of 5-30oC and humidity of 45-85%RH may be regarded as standard. 3-2. Unit setting conditions (1). Picture --10 step wave signal 1.5Vp-p(82Ohm load) (2). Audio -- 1.0Vp-p of sine wave 1KHz

Aug,15, 2001

1

COMTECH TECHNOLOGY CO., LTD.

FM2350TSIMP

4. Electrical Performance 4-1. Video system characteristics

Specification Parameter

Min Typ Max

4-1-1 Input impedance

1.3

4-1-2 Input signal level

1.0

4-1-3 Modulation Fp: 2480 MHz 2

3

K

4

sine wave 300 KHz 1Vp-p

4-1-4 Differential gain

4-1-5 Differential phase 4-1-6 S/N

-8

4-1-7 Out level taper

Aug,15, 2001

8

4

4-2. Audio system characteristics 4-2-1 Input impedance 4-2-2 Modulation 35 4-2-3 Distortion factor

4-2-4 S/N

8

-8 45

40

1.4 40

Unit

6

Remark Measure at 0.5-5MHz

Vp-p Load of 82Ohm connected negative synchronous MHz Superimposed sinuous wave. (3.58MHz)is 20% of the step input % level measure under the apl of 10-90% differential gain of demodulator unit is to be compensated deg -dittodB Measure with respect to standard demodulator output. dB fp 2350~2420MHz

KOhm Measure at 0.1-10KHz 45 KHz 3 % Audoi input signal 1.0Vp-p 1KHz modulation 50% (sine wave) video input signal all black (sync only) use standard demodulator of inter

dB

-carrier system. De-emphasis(50 usec) is on. The same as 4-2-3

2

COMTECH TECHNOLOGY CO., LTD.

FM2350TSIMP

4-3. Output system characteristics Specification. Parameter Min Typ Max Unit 4-3-1 Video carrier frequency -50 fp +50 KHz 4-3-2 Video output level 23 24 26 dBm (B3 -1.2V) 4-3-3 Audio output level difference(p/s ratio) 4-3-4 Audio carrier frequency

4-3-5 Audio modulator fs1 fs2 4-3-6 Out-band spurious 4-3-7 In-band spurious with bandwidth 4-3-8 Output impedance

Aug,15, 2001

22

27

32

-8

fs

+8

35 35 45 60

50 50 50

65 65

50

Remark Test at 25OC temperature and 65%RH of humidity Fp 2350~2420MHz Fs1 6.0 MHz dB Fs2 6.5 MHz *output channel KHz Input signal none the measurement is taken after 30 sec. from the power-on. KHz Measurement difference video of carrier frequency output level for dB 2350~2420MHz. except to fp. fp dB +/- fs against video carrier output level Ohm Unbalanced.

3

COMTECH TECHNOLOGY CO., LTD.

FM2350TSIMP

5-1. PLL section characteristics No Item Specification 5-2. IIC Bus (1) SDA.SCL Under standard test condition Input voltage Condition Min Typ Max High voltage 3 5 Low voltage 0 1.5 (2) Address C2 (on write date format) (3) SDA SCL SDA/SCL are in the high impedance Input impedance and there should be no reliablity problem with 5V continually on the SDA/SCL,if power supply is switched off. (4) Data format MSB LSB Address 1 1 0 0 0 MA1 MA0 0 Programmable 14 13 12 11 10 9 8 Divider 0 2 2 2 2 2 2 2 Programmable 7 6 5 4 3 2 1 0 Divider 2 2 2 2 2 2 2 2 Charge pump (0) (0) and test bits 1 cp t1 t0 1 1 1 os I/O port control bits p7 p6 p5 p4 p3 p2 p1 p0 Table 1 write data format (MSB is transmitted first) Address 1 1 0 0 0 MA1 MA2 1 Status byte POR FL I2 I1 I0 A2 A1 A0 Table 2 read date format A: Acknowledge bit. MA1,MA0: Voltage address bits. CP: Charge pump current select. T1: Test mode selection,T0:Charge pump disable OS: Varactor drive output disable switch. P7,P6,P5,P4,P3,P2,P1,P0: Control output states. POR: Power on reset indicator FL: Phase lock detect flag I2,I1,I0: Digital information from ports P7,P5,and P4. A2,A1,A0: 5 level adc data from P6

Aug,15, 2001

notes

V

A

Byte1

A

Byte2

A

Byte3

A A

Byte4 Byte5

A A

Byte1 Byte2

4

COMTECH TECHNOLOGY CO., LTD.

FM2350TSIMP

level

Aug,15, 2001

5