before closing. 0. Close the main box by using the Philips screwdriver (6). 0. 0. Seal the hole of the screw with the delivered reserve Q.C. hologram (silver ...
VIGIL II REPAIR & MAINTENANCE PROCEDURE FOR PARACHUTE RIGGERS & APPROVED SERVICE CENTERS 0
BATTERY0 PACK 0REPLACEMENT:
0
Switch off the Vigil Remove the hologram (Vigil seal from the main box) 0and clean the glue remains0 of the removed0 hologram. (1) Use 0 0 0 a Philips screwdriver n°1 TS to unscrew the two M3 closing0screws to open the box.0 (2) Disconnect the to replace0 battery0 pack by pulling out the little white center0 connector. (4) 0 Reconnect immediately the new battery0 pack and push it well in place.0 (5) 0 Don’t leave your Vigil with an empty Battery Pack due to the Pulses Plus Element That need to stay powered.Please remember that the battery pack must be replaced after 10 years of use For waterproof units, please add some silicon grease on the rubber sealing ring (mainly in the 4 rubber corners around the 2 connectors). If by opening you damage the rubber sealing ring, please place a new rubber sealing ring before closing.0 Close the main box by using the0 Philips screwdriver (6)0 0Seal the hole of the screw with the delivered reserve Q.C. hologram (silver with red numbers). 0 0The number on the seal must be the same 0as the one on the new battery0 pack0 and the service card. 0 See Warnings
0
1
4
2
5
3
6
0
_________________________________________________________________________________ Vigil repair & maintenance procedure ~1~ Version 1.0.60 November 2007
0
CUTTER UNIT OR CONTROL UNIT REPLACEMENT: 0 0
0
Switch off the Vigil Remove the hologram (Vigil seal from the main box) and clean the glue remains0 of 0the removed0 hologram. (1) Open the main box by using a Philips screwdriver n°1 TS to unscrew the two M3 closing0 screws. (2)0 0 Do not unplug the battery pack connector (vigil must be switch off but0 powered) To remove the jack connector you need to lift 0carefully (of about 2-3 mm) , the two connectors fixed on the front of the printed circuit. (4) Disconnect the two connectors, remove the rubber ring and replace the cutter: by fitting first the new rubber lightly greased with0 its flat side up and avoid to touch the gold plated 0 0 connectors with the sealing grease. Check that the connectors are correctly positioned (Cutter Unit, Control Unit marked on the PCB).00 Make sure that the battery pack’s connecting wires are correctly positioned and they do not hinder the main box from closing.0 Put a little silicon grease all around the new rubber as well as around the 2 connector’s 0 rings of the rubber. Put the connectors back in the 0 rings. Put the PCB back on its place and place correctly the new rubber in its groove all-around flat side-up. Put again a little silicon grease mainly at the connector’s corner. (5-6) Close the main box by using the0 Philips screwdriver0 0 Seal the hole of the screw with the delivered reserve Q.C. hologram ( silver with red numbers) (pict 2).0 The number on the seal must be the same 0as the one on the new cutter unit (pict 4) and the service card. 0 See Warnings0
0 0
0
1
4
0
2
5
3
6
_________________________________________________________________________________ Vigil repair & maintenance procedure ~2~ Version 1.0.60 November 2007
0
SOFTWARE UPDATE:
Update is possible if wanted but not mandatory and can preferably be done with a possible repair or maintenance action. The software update can only be done by AAD s.a./n.v. Brussels.
CUTTER ACTIVATION: Try to download the graph with the IR download box or send it to the nearest dealer who can do it. Ask him to send those graphs by email to our Brussels office. Fill in the “life saving report” (can be downloaded on our website: www.vigil.aero\downloads\ ) (Annexe 1.) and send it by fax to AAD Brussels (Fax: 0032/ 2 736 06 27) AAD Brussels will analyse the file (graph) and determine if it is an actual life saving, if yes a free cutter unit replacement will be send free to you, if not the cutter unit will have to be paid by the customer. To change the cutter unit (see cutter unit change procedure)
WARNINGS: 1. When a subpart is replaced (power pack, cutter unit or controller unit) please always update your internal customer list and send back the filled in Service Card to AAD s.a./n.v. Brussels for your customers warranty. 2. Only approved Vigil official service center are able to guaranty the waterproof function of the Vigil II unit. 3. After replacement of the necessary subpart please switch on the Vigil and check if all the parameters are ok. 00
_________________________________________________________________________________ Vigil repair & maintenance procedure ~3~ Version 1.0.60 November 2007
The Vigil® takes this altitude correction into account to calculate the new activation .... that you shut down and restart your Vigil® to guarantee optimal ... A new cutter will be supplied free of charge if a completed âLife Saving ..... Total W
Nov 1, 2012 - The I.R. Download Box is connected to the computer via a standard ... Software 2.11 can be installed on all computers that use Windows 7, ...
... understand this user's manual before any use of the Vigil® Cuatro. ..... It is a revolutionary safety device, with no imposed maintenance schedule. The Vigil® ...
Nov 1, 2012 - I & II Download ... Nov 2012. 2/19. The Vigil is endorsed by: ..... grafically in memory 7 sec before start of freefall and stops 12 sec after end of.
It contains explanations that will be useful to the airport security staff. ... A skydiver should always adhere to all rules and regulations set by his/her country's ..... you must switch OFF your Vigil® Cuatro before travelling in a closed vehicle
May 3, 2015 - connectors ensure optimal connection reliability in all circumstances. ... In freefall, the Vigil®2+Xtreme starts to continuously calculate the .... A new cutter will be supplied free of charge if a completed âLife ..... Total Weight
Nov 1, 2014 - 16. D. EXAMPLES OF ACTIVATION GRAPHS. .... The Vigil® is the only AAD on the market that has a readable data recorder function (black box), which is accessible to its user. .... Use the mouse wheel to scroll up and down in the graph sc
Do not remove the Controller Unit from the IR Download Box during process! .... The two comment fields are added to every graph's title bar for that specific ...
either by hand (see .Pdf file downloadable at: www.vigil.aero/files/images/pdf/Life_Saving_Report.pdf#blank) or on-line (see www.vigil.aero/live-saving-report).
Vigil® in a Tandem or Student system, we advise, if it has not already been done during the initial inspection, to enter into the âSetupâ sequence, and configure ...Missing:
Page 1 ... Battery (2 AA cells) contained in equipment (UN3091),. UN test passed by manufacturer. Little plastic specific ... Project Manager ... Control unit.
Information regarding the Activation Altitude . .... Technical Specifications . .... English. 2. Introduction. Your Vigil® Cuatro was designed and developed by a ...... instructions on www.vigil.aero/wp-content/uploads/New-RMA-procedure.pdf and ...
Mar 23, 2017 - and clear, abnormal indentation marks caused by the reserve closing loop. Background. We recently have found a few cutters in the field that ...
pocket. 2. Vigil 2 AAD assembly with Spectra closing loop and washer- Vigil or Cypres configuration (Figure 1). Note: The instructions and following photos are.
coincides with the momentum (8) (see, e.g., [4, 5]). At the same time, we underline that such equality cannot be correct in a general case. Indeed, the momentum.
to violation of Newton's third law in EM interaction. ...... This equation signifies that the particle takes its kinetic energy, reducing the heating of the disks.
Oct 3, 2011 - was found after the jump (X-Ray = NDI: Non Destructive Investigation). We received from A.A.D. nv/sa also X-ray photos of cutters taken by the.
Oct 20, 2011 - The manufacturer of the cutter assembly has confirmed that the failure to install the knife blade was caused by error during the cutter assembly ...
Papierschablonen können sich durch Luftfeuchtigkeit verändern. Verbindlich sind daher nur die MaÃangaben. Paper templates might distort due to air moisture.