VIGIL REPAIR & MAINTENANCE PROCEDURE FOR PARACHUTE RIGGERS & APPROVED SERVICE CENTERS 0
POWER PACK 0REPLACEMENT: 0
Switch off the Vigil Remove the hologram (Vigil seal from the main box) and clean the rest of the previous hologram. Open the main box with the hexagonal key Disconnect the old power pack 0 Connect the new power pack Remark: This new power pack must have a hologram on the white sticker (pict 1). Close the main box with the hexagonal key Seal the hole of the screw with the delivered reserve Q.C. hologram(pict 2)0 The number on the seal must be the same 0as the one on the new power pack(pict 1) and the service card. 0
CUTTER UNIT REPLACEMENT: 0 Switch off the Vigil Remove the hologram (Vigil seal from the main box) and clean the rest of the 0 previous hologram. Open the main box with the hexagonal key Partially unscrew the printed circuit board fixing screw 3 turns to the left 0(pict 3) 0 Unplug the old cutter unit 0 0 Plug in the new cutter unit 0 Tighten the printed circuit board fixing screw 3 turns to the 0right (pict 3) 0 0Close the main box with the hexagonal key Seal the hole of the screw with the delivered reserve Q.C. hologram (pict 2).0 The number on the seal must be the same 0as the one on the new cutter unit (pict 4) and the service card. 00
_________________________________________________________________________________ Vigil repair & maintenance procedure ~1~ Version 1.0.5 November 2005
CONTROL UNIT00REPLACEMENT: 0 0
Switch off the Vigil Remove the hologram (Vigil seal from the main box) and clean the rest of the previous hologram. Open the main box with the hexagonal key 0 Partially unscrew the printed circuit board fixing screw 0 3 turns0 to the left (pict 3) 0 Unplug the old control0 unit Plug in the new control0 unit 0 0Tighten 0the 0printed circuit board fixing screw 3 turns to the right (pict 3) Close the main box with the hexagonal key0 Seal the hole of the screw with the delivered reserve Q.C. hologram (pict 2)0. The number on the seal must be the same 0as the one on the new control unit (pict 5)0 and the service card.
Pict 5 SOFTWARE UPDATE: Update is not mandatory and can be done with 0a possible repair or maintenance. Software update can only be done by AAD s.a./n.v. Brussels.
CUTTER ACTIVATION: Try to download the graph with the IR download box or send it to the nearest dealer who can do it. Fill in the “life saving report” (can be downloaded on our website: www.vigil.aero\downloads\ ) (Annexe 1.) and send it by fax to AAD Brussels (Fax: 0032/ 2 736 06 27) AAD Brussels will analyse the file (graph) and determine if it is an actual life saving (free cutter unit replacement) or not (cutter unit to be paid by customer) To change the cutter unit (see 0cutter unit change procedure)
GENERAL REMARKS: When a subpart is replaced (power pack, cutter unit or controller unit) please always update your internal customer list and send back the filled in Service Card to AAD s.a./ n.v. Brussels for your customers warranty. _________________________________________________________________________________ Vigil repair & maintenance procedure ~2~ Version 1.0.5 November 2005
before closing. 0. Close the main box by using the Philips screwdriver (6). 0. 0. Seal the hole of the screw with the delivered reserve Q.C. hologram (silver ...
Nov 1, 2012 - The I.R. Download Box is connected to the computer via a standard ... Software 2.11 can be installed on all computers that use Windows 7, ...
... understand this user's manual before any use of the Vigil® Cuatro. ..... It is a revolutionary safety device, with no imposed maintenance schedule. The Vigil® ...
It contains explanations that will be useful to the airport security staff. ... A skydiver should always adhere to all rules and regulations set by his/her country's ..... you must switch OFF your Vigil® Cuatro before travelling in a closed vehicle
May 3, 2015 - connectors ensure optimal connection reliability in all circumstances. ... In freefall, the Vigil®2+Xtreme starts to continuously calculate the .... A new cutter will be supplied free of charge if a completed âLife ..... Total Weight
Nov 1, 2012 - I & II Download ... Nov 2012. 2/19. The Vigil is endorsed by: ..... grafically in memory 7 sec before start of freefall and stops 12 sec after end of.
Nov 1, 2014 - 16. D. EXAMPLES OF ACTIVATION GRAPHS. .... The Vigil® is the only AAD on the market that has a readable data recorder function (black box), which is accessible to its user. .... Use the mouse wheel to scroll up and down in the graph sc
Do not remove the Controller Unit from the IR Download Box during process! .... The two comment fields are added to every graph's title bar for that specific ...
either by hand (see .Pdf file downloadable at: www.vigil.aero/files/images/pdf/Life_Saving_Report.pdf#blank) or on-line (see www.vigil.aero/live-saving-report).
Vigil® in a Tandem or Student system, we advise, if it has not already been done during the initial inspection, to enter into the âSetupâ sequence, and configure ...Missing:
Page 1 ... Battery (2 AA cells) contained in equipment (UN3091),. UN test passed by manufacturer. Little plastic specific ... Project Manager ... Control unit.
Information regarding the Activation Altitude . .... Technical Specifications . .... English. 2. Introduction. Your Vigil® Cuatro was designed and developed by a ...... instructions on www.vigil.aero/wp-content/uploads/New-RMA-procedure.pdf and ...
The Vigil® takes this altitude correction into account to calculate the new activation .... that you shut down and restart your Vigil® to guarantee optimal ... A new cutter will be supplied free of charge if a completed âLife Saving ..... Total W
Mar 23, 2017 - and clear, abnormal indentation marks caused by the reserve closing loop. Background. We recently have found a few cutters in the field that ...
drying patch of weeping fuel on the outside of the tank, perhaps from a .... fitted between the twin tanks and their fuel pumps. I shall be fitting said filters. After a.
pocket. 2. Vigil 2 AAD assembly with Spectra closing loop and washer- Vigil or Cypres configuration (Figure 1). Note: The instructions and following photos are.
Oct 3, 2011 - was found after the jump (X-Ray = NDI: Non Destructive Investigation). We received from A.A.D. nv/sa also X-ray photos of cutters taken by the.
Oct 20, 2011 - The manufacturer of the cutter assembly has confirmed that the failure to install the knife blade was caused by error during the cutter assembly ...
