pocket. 2. Vigil 2 AAD assembly with Spectra closing loop and washer- Vigil or Cypres configuration (Figure 1). Note: The instructions and following photos are.
RIGGING INNOVATIONS VIGIL 2 INSTALLATION INSTRUCTIONS BACKGROUND The following instructions are for use in assembling the Vigil 2 AAD into Rigging Innovations Inc (RI) harness and container systems. As of the below date, they are approved for use with the following systems: Talon 3.0 (Including FS and FX) Talon 2 Telesis 3.0 Telesis 2 Genera Earlier systems such as the Talon 1, Telesis 1, and Flexon, may require certain minor changes to accommodate the Vigil 2. Contact RI for further information before assembling the Vigil 2 to these systems. Needed components: 1. RI harness and container assembly with Cypres AAD installation including pocket, channels, cutter elastic, and control unit pocket. 2. Vigil 2 AAD assembly with Spectra closing loop and washer- Vigil or Cypres configuration (Figure 1). Note: The instructions and following photos are taken of a Talon FX2 system which has a small (170mm) Cypres pocket installed.
Figure 1
PROCEDURE. Step 1. Take the Vigil 2 power unit and with the orange Vigil logo facing the bottom wall of the reserve container, route the power unit UNDER the 1" loop Velcro strip located adjacent to the mouth of the pocket and then into the elastic pocket. The cutter cable should be positioned towards the top of the pocket and the control cable near the bottom of the pocket. (Figure 2). Figure 2
Step 2. Route the cutter cable out the left side of the loop Velcro as you are facing it. Loop the cable towards the bottom of the container and then route the cutter UP and BEHIND the cables BETWEEN the cable and the base of the pocket. (Figure 3).
Figure 3
Step 3. Route the cutter through the elastic channel and then position it in the elastic keeper and UNDER the TY-12 cutter protector. (Figure 4).
Figure 4
Step 4. Pull the excess cable out the bottom of the pocket and form a gentle loop. (Figure 5).
Figure 5
Step 5. Stow this excess cable in the pocket located in the bottom tray between the stiffener plate and the AAD pocket on the center wall. (Figure 6).
Step 6. Take the control head and route it UNDER the cover of the channel in the bottom of the pack tray. (Figure 7).
Figure 7
Step 7. Route the control head OUT THE TOP of the channel and place into the pocket at the top of the container. Coil the excess cable as in Figure 8, and then insert it back into the channel as in Figure 9. The result should look like Figure 10 with the cable exiting from the far side of the channel to form a gentle loop to the control head. Figure 8
Figure 9
Figure 10
Step 8. Close the Velcro pocket cover flap (Figure 11). The assembly is now complete. Check the operation of the unit to make sure all connections are secure and that the AAD is operational.
malfunctions that may be fatal. Kill-line pilot chutes MUST be cocked each time the parachute is packed. Remove the rapide link from bottom end of bridle.
hard openings by never exceeding the limits shown on the warning label. ... Some body positions (i.e. head down, stand up, and long dives) ...... Main lift web. 2.
Dec 1, 2015 - hard openings by never exceeding the limits shown on the warning label. ... Some body positions (i.e. head down, stand up, and long dives) may enable the ..... Bend forward at your waist and hoist your rig from the bottom so ...
Mar 24, 2014 - SERVICE BULLETIN: RI harness and container systems listed above may be assembled with the MarS M2, by a certificated and appropriately ...
Dec 1, 2015 - Some body positions (i.e. head down, stand up, and long dives) may enable the ... If the buyer declines to waive liability on the part of the manufacturer, buyer may obtain a full ..... Bend forward at your waist and hoist your rig.
Dec 1, 2015 - malfunctions that may be fatal. Kill-line pilot chutes MUST be cocked each time the parachute is packed. Remove the rapide link from bottom ...
Dec 1, 2015 - program of instructionâ in the use of this parachute ..... Route main risers over shoulders and close the main riser covers and route the main ...
Apr 25, 2012 - The Talon FS and FX are very similar in construction and therefore in ... Step 4. Position the ring on the end of the lanyard BETWEEN the two ...
May 3, 2001 - manufacturing whether caused by negligence on the part of the .... relocation to preclude interruption while awaiting quality control approval of your new facility .... Proper container sizing is one of the more difficult processes in .
... understand this user's manual before any use of the Vigil® Cuatro. ..... It is a revolutionary safety device, with no imposed maintenance schedule. The Vigil® ...
It contains explanations that will be useful to the airport security staff. ... A skydiver should always adhere to all rules and regulations set by his/her country's ..... you must switch OFF your Vigil® Cuatro before travelling in a closed vehicle
May 3, 2015 - connectors ensure optimal connection reliability in all circumstances. ... In freefall, the Vigil®2+Xtreme starts to continuously calculate the .... A new cutter will be supplied free of charge if a completed âLife ..... Total Weight
Wing chord incidence bar with "devil level" ... control pressures in long cross-country flights and in ... and aileron controls creates a hazard during cross-wind.
Do not remove the Controller Unit from the IR Download Box during process! .... The two comment fields are added to every graph's title bar for that specific ...
either by hand (see .Pdf file downloadable at: www.vigil.aero/files/images/pdf/Life_Saving_Report.pdf#blank) or on-line (see www.vigil.aero/live-saving-report).
Vigil® in a Tandem or Student system, we advise, if it has not already been done during the initial inspection, to enter into the âSetupâ sequence, and configure ...Missing:
Page 1 ... Battery (2 AA cells) contained in equipment (UN3091),. UN test passed by manufacturer. Little plastic specific ... Project Manager ... Control unit.
minutes away from the city center by bus. Contact. For more information and further details, please feel free to check out either http://www.i4cs-conference.org/.
less than the numbers in your operations manual. While it's questionable whether any of .... A calibrated cable tensiometer is a must for this task, and the adjust-.
