PRODUCT NAME:Swank 1LT Pendant ITEM NUMBER: E24591
Please consult your electrician for hanging fixture and wiring.
The fixture is designed to dim with a standard Triac forward phase dimmer. Dimming levels will vary by dimmer. Below is a list of recommended dimmers: Lutron MACL-153M Lutron DVL-153P Lutron SCL-153P Leviton IPL06-10Z Leviton 6674-POW Due to inrush current wattage should not exceed 150 watts of product for a 600 watt dimmer.
WARNING: Wires need to be connected to driver found in canopy and should not be connected directly to power source or a short may occur.
Bulbs ( Included ):1*LED*6W
MADE IN CHINA Page 1 of (2)
IMPORTANT: Turn off the power at the main fuse or circuit breaker box before starting installation
Bracket (A)
Screws(B)
Mounting Screws(C)
Canopy(D)
Locate all hardware & components before discarding packaging A B
1.)
(A) (B) (C)
C D
Step1 :Remove mounting bracket from fixture and install to electrical box.
2.)
(A) Green/Ground White/Neutral Black/Positive (D)
Step2 :Adjust wire length to desired mounting height, and tighten strain relief screws to secure. Wire fixture to wires in outlet box. Green wire is for Ground.
3.)
Cleaning & Care: Clean with soft cloth and a mild detergent. Do not use abrasive cleaner.
(B) (D)
Step3 :Install fixture to bracket and Screws at the ends of the canopy to secure.
like a cutter knife, be careful not to damage the components ... Ensure that you have all required contents for complete ... CAUTION: Xenon bulbs get very hot.
Leave a Small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur ...
Please consult your electrician for hanging fixture and wiring. ... IMPORTANT: Turn off the power at the main fuse or circuit breakerbox before staringinstallation.
MADE IN CHINA ... 2.) \ |. Step.2: Install candelabra bulbs (3pcs), and. Attach Sheet glass(C) into the Fixture(A). Etape 2: Installer des ampoules CA (3pcs),.
Ãtape 3: Installer les ampoules CA (3pcs). Step.1: Remove mounting bracket from fixture(B) and install to electrical box. then wire fixture to wires in outlet box.
Periodically (every 90 days) make sure that the screws are fully tightened. Periódicamente (cada 90 días) asegúrese de que los tornillos estén bien apretados.
This fixture is designed to dim with an Electronic Low Voltage dimmer. Dimming ... Locate all hardware & components before discarding packaging. Localisez ...
Leave a small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur en ...
This fixture is designed to dim with an Electronic Low Voltage dimmer. Dimming ... Locate all hardware & components before discarding packaging. Localisez ...
This fixture is designed to dim with an Electronic Low Voltage dimmer. ... Locate all hardware & components before discarding packaging. Localisez tous les ...
Leave a small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur en ...
Before commencing installation or maintenance, ensure electricity is switched off at the mains. 1. Fit the mounting bracket in the required position. Be aware of ...
T. I N. G. HINKLEY. English. Spanish. French. HINKLEY LIGHTING. 33000 Pin .... Connect ground wire to mounting strap (1) using green ground screw (GS). 4.
After screws are removed, lift the top of the fixture (T) upward and off of ..... caulk or sealant be put under the ball knobs used to mount fixture â see Drawing. 2.
ESTAS PROVAS DEVEM SER RESPONDIDAS PELOS CANDIDATOS AOS. CURSOS DO GRUPO D. GRUPO D. Letras Vernáculas ... Responda à s questões, em PORTUGUÃS, com caneta de tinta AZUL ou PRETA, de forma clara e legÃvel. Entretanto, haverá uma questão envolven
