Leave a Small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur ...

Please consult your electrician for hanging fixture and wiring. ... IMPORTANT: Turn off the power at the main fuse or circuit breakerbox before staringinstallation.

Veuillez consulter votre électricien pour la fixation et le raccord des fils. Back Plate/Plaque arrière. (A). Light Body/Corps de lampe. (B). (B). Step 1: Remove the ...

Etape 1: Retirer la plaque arrière du baldaquin et attacher la à la boîte de dérivation. To prevent water intrusion, caulk around back-plate where fixture meets the ...

Step.1: Remove hood from the post by unscrewing top finial and two screws within the hood. Étape 1: Enlever le capot du poteau en dévissant le fini supérieur et ...

Étape 3: Installer les ampoules CA (3pcs). Step.1: Remove mounting bracket from fixture(B) and install to electrical box. then wire fixture to wires in outlet box.

Periodically (every 90 days) make sure that the screws are fully tightened. Periódicamente (cada 90 días) asegúrese de que los tornillos estén bien apretados.

Leave a small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur en ...

LIGHTING. PRODUCT NAME/NOM DU PRODUIT :Influx ... Afin d'éviter l'intrusion d'eau, calfeutrer la ... à l'aide d'un mastic silicone d'extérieur. |. Step 2: Use the ...

Top cover (G) Fini. : (E) Neck (F) Le couvercle : (H) puche(E) Cou(F) supérieur(G) euron(H). Locate all hardware & components before discarding packaging.

MADE IN CHINA ... 2.) \ |. Step.2: Install candelabra bulbs (3pcs), and. Attach Sheet glass(C) into the Fixture(A). Etape 2: Installer des ampoules CA (3pcs),.

PRODUCT NAME: Terrace. ITEM NUMBER: 3250. NOM DU PRODUIT: Terrace. NUMÉRO D'ARTICLE: 3250. Please consult your electrician for hanging fixture ...

This fixture is designed to dim with an Electronic Low Voltage dimmer. Dimming ... Locate all hardware & components before discarding packaging. Localisez ...

This fixture is designed to dim with an Electronic Low Voltage dimmer. ... Locate all hardware & components before discarding packaging. Localisez tous les ...

Leave a small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur en ...

I. G. H. T. 1. N. G. PRODUCT NAME: Canterbury. ITEM NUMBER: 20455. NOM DU PRODUIT: Canterbury. NUMÉRO D'ARTICLE: 20455. Please consult your ...

Etape 1: Retirer le support de fixation du luminaire (B) et l'installer sur la boîte ... silicone sealant. Leave a small gap at the bottom to allow moisture to escape.

Step.1: Remove mounting bracket from fixture(B) and install to electrical box. Etape 1: Retirer le support de ... MADE IN CHINA/Fabriqué en Chine. Page 2 of (2).

fixture meets the wall using outdoor silicone sealant. Leave a small gap at the bottom to allow moisture to escape. Eape 3: Placez l'appareil sur la plaque arrière ...

Leave a Small gap at the bottomto allow moisture to escape. Pour empêcher l'intrusion d'eau, calfeutrez autour de la plaque arrière où l'appareil rencontre le.

like a cutter knife, be careful not to damage the components ... Ensure that you have all required contents for complete ... CAUTION: Xenon bulbs get very hot.

Read the instructions carefully prior to assembling ... endommager les composants à l'intérieur. Cuando ... Choose a clean, level, spacious assembly area. ... to driver found in canopy and should ... not exceed the maximum wattage as it could.

MAX6138_12. REVERSE VOLTAGE vs. ISHUNT. MAX61438 toc05. ISHUNT (mA). REVERSE VOLTAGE CHANGE (mV). TA = +85°C. TA = +25°C. TA = -40°C.

160. ON-RESISTANCE vs. VCOM. (DUAL SUPPLIES). 100. MAX308/9 TOC-01. 0. 20. 40. 60 .... below V+ and 1V above V-, but does not affect the devices' low ...