Periodically (every 90 days) make sure that the screws are fully tightened. Periódicamente (cada 90 días) asegúrese de que los tornillos estén bien apretados.
PRODUCT NAME:Pier M 1-Light Wall Sconce ITEM NUMBER: 35015
Please consult your electrician for hanging fixture and wiring.
WARNING: To prevent water intrusion,caulk around back-plate where fixture meets the wall using outdoor silicone sealant. Leave a small gap at the bottom to allow moisture to exit.
Bulb ( not included): : 1 x 60W Candelabra Bulb
MADE IN CHINA Page 1 of (2)
IMPORTANT: Turn off the power at the main fuse or circuit breaker box before starting installation
Bracket (A)
Integral lamp holder (B)
decorative nut(C)
Locate all hardware & components before discarding packaging
1.A)
Step.1 Remove mounting bracket from fixture and install to electrical box. (L) Black/Positive
Metal bending arm
Mounting Screw
Nipple
Cross Bar
Terminalcap
Supply Wire
Metal cup Bald headed Ceramic lamp head
2.B)
Green/Ground
light source
(N)White/Neutral
Metal cover
Green/Ground
Outlet Box
(L) Black/Positive
Step.2 Wire fixture to wires in outlet box. Black wire is positive, white is neutral, bare wire is ground.
(N)White/Neutral
Bald headed
3.C)
light source
Cleaning & Care: Clean with soft cloth and a mild detergent. Do not use abrasive cleaner.
Step.3 Put the connected line into the electric box and fasten the light body with the decorative nut.
Leave a Small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur ...
Please consult your electrician for hanging fixture and wiring. ... IMPORTANT: Turn off the power at the main fuse or circuit breakerbox before staringinstallation.
Ãtape 3: Installer les ampoules CA (3pcs). Step.1: Remove mounting bracket from fixture(B) and install to electrical box. then wire fixture to wires in outlet box.
This fixture is designed to dim with an Electronic Low Voltage dimmer. Dimming ... Locate all hardware & components before discarding packaging. Localisez ...
Leave a small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur en ...
MADE IN CHINA ... 2.) \ |. Step.2: Install candelabra bulbs (3pcs), and. Attach Sheet glass(C) into the Fixture(A). Etape 2: Installer des ampoules CA (3pcs),.
This fixture is designed to dim with an Electronic Low Voltage dimmer. Dimming ... Locate all hardware & components before discarding packaging. Localisez ...
This fixture is designed to dim with an Electronic Low Voltage dimmer. ... Locate all hardware & components before discarding packaging. Localisez tous les ...
Leave a small gap at the bottom to allow moisture to exit. Pour empêcher l'intrusion d'eau, calfeutrer autour de la plaque arrière où l'appareil rencontre le mur en ...
Etape 1: Retirer le support de fixation du luminaire (B) et l'installer sur la boîte ... silicone sealant. Leave a small gap at the bottom to allow moisture to escape.
fixture meets the wall using outdoor silicone sealant. Leave a small gap at the bottom to allow moisture to escape. Eape 3: Placez l'appareil sur la plaque arrière ...
Leave a Small gap at the bottomto allow moisture to escape. Pour empêcher l'intrusion d'eau, calfeutrez autour de la plaque arrière où l'appareil rencontre le.
like a cutter knife, be careful not to damage the components ... Ensure that you have all required contents for complete ... CAUTION: Xenon bulbs get very hot.
160. ON-RESISTANCE vs. VCOM. (DUAL SUPPLIES). 100. MAX308/9 TOC-01. 0. 20. 40. 60 .... below V+ and 1V above V-, but does not affect the devices' low ...