Heater LED - ON when the PIC is requesting the heater to be turned ON and the ... Over Temperature Shutdown active, the corresponding heater output was ...
Maxum Detector Personality Module (DPM) LED Definitions Temperature control LEDs Color
Name
Description
Green
HEATER
Heater LED - ON when the PIC is requesting the heater to be turned ON and the “temperature limit protection” is not active. The corresponding heater output is enabled.
Yellow
TEMPLIMIT
Temperature Limit - protection active, the corresponding heater output is temporarily disabled as the temperature of the heater is too high.
Red
OVERTEMP SHUTDOWN
Over Temperature Shutdown active, the corresponding heater output was shutdown as a safety precaution. An alarm is sent to the Syscon
Standard PIC LEDs Green
Yellow
Red
Module Status
Required Action
OFF
OFF
OFF
1. power off
none; normal
ON
ON
2. Power-on (or reset) self test in progress; LED test on
None if condition does not persist for more than ~0.5 second; replace module if persists or check wiring
ON
ON
3. Self-test completed okay; Module non-operational, and waiting for address assignment
None if condition does not persist for more than ~10 seconds; need remedial action to module or associated item if condition persists
OFF
OFF
4. Normal operation with no communication
None; normal
OFF
OFF
DIM or ON
ON
OFF
DIM or ON
OFF
ON
ON
OFF
DIM ON
5. Normal operation with communication 6. Module or associated item is in marginal condition; or communication errors are occurring 7. Module or associated item is in fault state, current analyzer data is invalid
None; normal Need to repair or replace this module or an associated item Need to repair or replace this module or an associated item
Notes: • States 2-3 are normal temporary states for the module to pass through during power up or reset of the module. • States 4-5 are the normal fully operational states of the module. • States 6-7 are the warning and fault states of the module. The LED’s will indicate this state for the duration of the warning or fault condition. • In a warning condition, the analyzer data is probably still valid, but maintenance attention is needed. In the fault state, the current analyzer data is probably not valid. • These states are intended to indicate that a physical repair/replacement is needed to the module or an associated item. Configuration errors, etc. that require a database change to correct the situation are not indicated on the LED’s. • The green LED serves as a power-on indicator in states 4-7 by being DIM when no communication is present. The LED will go to full brightness when communication activity is present.
Flame Sense LED – Flame Ignite LED Not all detectors have flame sense capability. If this feature is available, the RED LED is ON for flame OUT. However if the LED is OFF it does not necessarily means that the flame is lit. The ignite yellow LED is ON when the ignition circuit is active and the proper condition are met. For a glow plug it means that the voltage and current must exceed a minimum limit. For the spark ignite, the Ignite LED flashes for each time a spark is initiated.
Range Change (Low Gain) LED The Range Change LED is just below the temp lights. It is on when the mezzanine board range change is ON.
DPM LED.doc
DPM LED DOCUMENT
Page 1 of 2
DPM LED Locations: Base DPM 2020963-001: Heater 1 Temp Limit 1 Overtemp 1 Alternate Range
|| || || || || || || || || || || || || ||
Heater 2 Temp Limit 2 Overtemp 2
Flame Out Ignite Normal/Communication Fault Warning
+500 to +1820. 0 to +2300. 0 to +2300. --250 to. +900. --210 to +1200. --230 to +1370. --200 to. +900. --200 to +1300. 0 to +1750. 0 to +1750. --220 to. +400.
In the G8ACE MKII OCXO part of the setup procedure is to explore for the ... the crystal will retrace overnight and each subsequent day will repeat the process.
Configuration système requise. • Port USB-A disponible. • Windows XP / Vista / 7 / 8.1 / 10 ou Mac OS 9 ou version supérieure. • PS4 (entièrement compatible).
hook them up or how the landing light works. Patience, patienceânext month we'll tackle the landing light, how LEDs are powered, and a couple of ideas on.
power still applied. When opening covers or ... Overview. Description. This manual provides instructions for installation of the Maxum edition ..... If a forklift or dolly is used, make sure the Maxum II is strapped to it se- curely. Add padding ..
The Thermalert EC100 is an easy-to-use system. The Linescanner ... Raytek Thermalert® MP infrared linescanner with ... Data recall for easy thermal analysis.
The HydroRanger 200 is a single-point, six relay device that offers both level and volume ... è Wall Mount: suitable for outdoors (Type / Nema 4x, IP65 Enclosure).
24, ost SA locking cevice. 27, Air evoCuction CDrtoiner ... Note the side clistance oetween or evacuation CDntainer and probe, ca, 500mm. Datur 2, 2,96. Bedro ...
be construed as a commitment, representation, warranty, or guarantee of any method, ...... Once your PC is set up, as described in Configuring Your PC, you are.
Description. In the methanator CO and CO2 are ... Methanator Operation. Ni. CO + 3 H2. â. CH4 + H2O. Ni ... Operational Note. File: Filament.DOC. Removal ...
This device/system may only be set up and operated in conjunction with this manual. ... Under Weighing Technology, select Continuous Weighing Systems and then go to the manual ...... The distance calculation is dependent upon the ambient sound. .....
This unit mounted C7250A temperature sensor includes solid state temperature sensors. ⢠Outputs a 20k NTC signal to the controller based upon temperature. This enables economizer modes of operation when outside air temperature is suitable for free
Neopren. Rubber bushing. EPDM 50. Packaging. Bio-degradable cardboard. 3K. âÎ. 2K. âÎ ... However, the data in this manual are reviewed regularly and any.
92+0.8 mm x 45+0.6 mm. ⢠Upright version. 45+0.6 ... Electric connection. Tab connector 6.3 x 0.8 or ..... 62.5 mm at BV 3340 of Federal. Navy (Order No. N98).
values of several measuring chan- nels, of status informations as well as diagnosis signals for preventive maintenance.The limited dynamics of 4-20 mA signals ...
GENERAL. This instruction manual contains information essential to successful CompuScale III operation. ... PROGRAMMING CHART, provides a space to record programmed parameter values for future reference. ...... POS B L/C (A + B) (V).
longest cycletime in the Maxum's method table for an application, even ..... 3051 162. 1. 3. SEL. 0. 1. 38. B. 3052 162. 2. 3. SEL. 0. 1. 39. B. 3101 162. 1. 3. CUR.
using efficacy, which in basic terms is the ratio of power input to light outputâor more technically, emitted flux (lumens) divided by power draw (watts).1 For such ...
The options cards 6DR2800-8P and 6DR2800-8T have been replaced with the controllers SIPART DR19 and. SIPART DR21 as well as the modification of the ...
