Push-fit Visit www.sharkbite.com/icemaker for detailed product information.
ENSEMBLE DE RACCORDEMENT POUR APPAREIL À GLAÇONS
Raccords à Pression Visitez www.sharkbite.com/icemaker pour des renseignements détaillés sur le produit. JUEGO DE CONEXIÓN PARA MÁQUINA DE HACER HIELO Conexión a Presión
Visite www.sharkbite.com/icemaker para información detallada del producto.
Plumbing Solutions
www.sharkbite.com
PART #: 25024
2a
2b
QUICK CONNECT INSTALLATION 1. Shut off water supply. 2. Mark 2" section of cold water line and remove.
3
4
3. Deburr, and mark insertion depth (0.95") on both ends of copper pipe. 4. Push slip end of the tee onto one end of the copper pipe.
5
6
5. Use the demount clip to retract slip tee on to the other end of the pipe and ensure proper insertion depth. 6. Push supply stop to the second groove on the tee’s tube end. 7. Mark PEX tube (0.81") and push into fixture stop.
7
8
8. Thread fitting onto ice maker valve; tighten. 9. Mark PEX tube (0.81") and push into fitting. 10. Turn water supply on and check for leaks.
9
10
Cut. Push. Done. Fixture connections are easy with SharkBite®.
INSTALLATION À RACCORD RAPIDE
INSTALACIÓN DEL CONECTOR RÁPIDO
1. Fermer l’arrivée d’eau.
1. Cierre el suministro de agua.
2. Tracer une section de 2" sur la conduite d’eau froide et l’enlever.
2. Marque una sección de 2" del conducto de agua fría y retírelo.
3. Ébarbez, et marquez la profondeur d’insertion (0.95") des deux côtés du tuyau en cuivre.
3. Desbarbe y marque la profundidad de inserción (0.95") en ambos lados del tubo de cobre.
4. Poussez l’un dans l’autre le tuyau et le cote côté coulissant du raccord en T. 5. Tout en poussant l’étrier de déconnexion contre la bride de détente sur le côté coulissant du raccord T, poussez le raccord en té sur l’autre tuyau pour assurer la profondeur d’insertion appropriée.
4. Empujé el lado deslizable del accesorio "T" en un lado del tubo de cobre. 5. Utilice el clip de desmontaje para deslizar el accesorio "T" hacia el otro tubo de cobre y asegure una profundidad de inserción adecuada.
6. Pousser l’arrêt de la conduite d’arrivée jusqu’à la deuxième encoche de l’extrémité du T.
6. Lleve el tope hasta la segunda ranura del tubo del conector en T.
7. Tracer le tube PEX (0.81") et le pousser dans l’arrêt du raccord.
7. Marque el tubo PEX (0.81") e inserte en el tope del aparato.
8. Visser le raccord sur le robinet de l’appareil à glaçons; serrer.
8. Enrosque y ajuste el conector en la válvula de la máquina de hacer hielo.
9. Tracer le tube PEX (0.81") et le pousser dans le raccord.
9. Marque el tubo PEX (0.81") e inserte en el conector.
10. Ouvrir l’arrivée d’eau et vérifier qu’il n’y a pas de fuite.
10. Abra el suministro de agua y compruebe si hay fugas.
Couper. Pousser. Terminé. Les raccordements sont faciles avec SharkBite®.
Corte. Empuje. Listo. Las conexiones del aparato se simplifican con SharkBite®.
Plumbing Solutions
Visit www.sharkbite.com/icemakerkit for installation instructions. Visitez www.sharkbite.com/icemaker pour des renseignements détaillés sur le produit. Visite www.sharkbite.com/icemaker para información detallada del producto.
www.sharkbite.com
Manufactured and distributed by Reliance Worldwide Corporation Fabriqué et distribué par Reliance Worldwide Corporation Fabricado y distribuido por Reliance Worldwide Corporation www.rwc.com
The following items will be required to install the ice maker kit: ⢠¼ inch copper supply line with shut off valve. ⢠¼ inch brass compression nut and ferrule.
Turn off and fully drain water supply to involved piping. 2. Nail the outlet box to the wall stud using the molded-in support flanges. For mounting to metal studs, use sheet metal screws (fig. A). 3. Connect water distribution line to the SharkBite p
With the progress in the fields of the adsorbent ... This idea is simple and also expected to be effective, since, the ... Such a novel concept of energy utilization.
Jenn-Air approved drain pump, Part Number 1901A, only to carry the water to an .... back into the ice maker storage bin and potentially flowing onto the floor ...
Before you move your ice maker into its final location, it is important to make sure you ..... Install the white decorative screws on the opposite side of the door. 4.
or a Whirlpool supply line Part Number 8212547RB, and a. Whirlpool approved drain pump, Part Number 1901A, only to carry the water to an existing drain. □.
Use two or more people to move and install ice maker. State of California .... NOTE: To allow sufficient water flow to the ice maker a minimum ¹⁄₂" diameter ...
use chlorine bleach on the stainless steel surfaces of the ice maker. ... is not available, it is the personal responsibility of the customer to have a properly ...
period of time, turn off the water and power supply to the ice maker. â¡ ...... Remove dirt and lint from the condenser fins and the unit ..... 553 Benson Road.
7⁄16" and ½" open-end wrenches or two adjustable wrenches. □. ¼" nut driver. NOTE: Do not ...... To locate factory specified parts in your area, call us or your.
and pull up. NOTE: Be sure the edge guards do not separate from the ...... Travel or transportation expenses for service in remote locations where an authorized.
If it is required by your local sanitation code, seal the cabinet to the floor with an approved caulking ...... Benton Harbor, MI 49022-2692. Please include a daytime ...
Maximum rise 10 ft (3.1 m). □. Maximum run 100 ft (30.5 m). NOTES: □. If the drain hose becomes twisted and water cannot drain, your ice maker will not work.
En Canadá, para obtener ayuda, instalación o servicio llame al: 1-800 807- ...... To locate the Whirlpool designated service company in your area, you can also ...
be closed-in on the top and three sides, but the installation should allow the ice .... osmosis system going to the water inlet valve of the ice maker needs to be between 30 ..... automatically reset the filter status tracking feature. See. “Using th
ICE MAKER. Use and Care Guide. For questions about features, operation/performance, parts, accessories, or service, call: 1-800-422-1230 or visit our website ...
PURPOSE, ARE LIMITED TO FIVE YEARS OR THE SHORTEST PERIOD ALLOWED BY LAW. ... If you want a longer or more comprehensive warranty than the limited warranty that comes with this .... de ósmosis inversa y va a la válvula de entrada de agua de ..... S