Oct 11, 2007 - Connect Garmin to kenwood. After GPS starts flashing, connect to computer. Run hyper terminal, 9600, Bits 8, Parity No, Start Bits 1, Flow ...
Garmin GPS to Kenwood TH-D7A & TM-D700A & TM-D710A Transceivers Dr. John A. Allocca WB2LUA 10/11/07
Garmin Emap
Kenwood D7A D700A D710A
DB9 Female
1 2 3 4 5 6 7 8 9
RXD TXD
RXD (white)
TXD (red) GND 2.5 mm, 3 conductor plug
DB9 Male Pin 2 = RXD Pin 3 = TXD Pin 5 = GND
Continued on next page…
Tip = White 2nd Barrel = Red Case = Shield
Garmin 60 CSX
Kenwood D7A D700A D710A
4 Pin Data
Data In (White) Ground (Black) Data Out (Brown)
To Data In on GPS (White) To Data Out on GPS (Red)
(Red)
Ground
2.5 mm, 3 conductor plug Shield is ground
+ 12-32 VDC ACG/3AG 1/2 amp fuse To Test Kenwood Output 1 2 3 4 5 6 7 8 9
To Data In on GPS (White) To Data Out on GPS (Red) 2.5 mm, 3 conductor plug Shield is ground
DB9 Female Pin 2 (Data In) Pin 3 (Data Out) Pin 5 (Ground) Connect Garmin to kenwood. After GPS starts flashing, connect to computer Run hyper terminal, 9600, Bits 8, Parity No, Start Bits 1, Flow Control None. $GPWL,…………………….. will appear if the D710 is set for NMEA. $PKWDWPL, ……………….. will appear if the D710 is set for Kenwood. Continued on next page…
White = Tip Red = Ring Shield = Base
Kenwood TM-D710A Radio Setup • Turn the radio ON. • Press the “F” key to access the Setup Menu. • Press the MHZ knob. • Turn knob to select APRS. • Press the BACK Button to select the next menu. Basic Setting Menu #600 • Enter your call sign. • Set Beacon Type to APRS. • Turn the MHZ knob to scroll through menus. Internal TNC Menu # 601 • Do not make any changes. Leave all settings at “Default.” • Data Band A-Band • Data Speed 1200 bps • DCD Sense D or RxD Band • TX Delay 200 ms GPS Port Menu #602 • Change the Baud Rate to 9600 or 4800 depending up the gps receiver speed. • Set the Input to “GPS” • Set the Output to “Waypoint” Waypoint Format Menu # 603 • Set Format to “NEMA” • Change NAME to “9-CHAR” • The Output setting should be set to “ALL” Beacon Information Menu # 606 • Speed setting should be turned ON • Altitude setting should be turned ON • Position Ambiguity should be turned OFF Beacon TX Algorithm Menu # 611 • Set the Method to “Auto” • Press ESC to return to the main page • Change the APRS Frequency to: 144.390 • Select TNC and press to turn on APRS 12 • Press “BCON” to turn on -- BCN will appear in the upper right corner If you interface the units and do not see a flashing “GPS” signal on the upper right hand corner of the Kenwood, then the APRS cable may not be plugged-in all the way or correctly. Please check that the cord is plugged into the proper ports and plugged-in all the way.
voltage ranges & fuse amperages of your GPS unit, please consult the owner's manual specifications. Once the connections are soldered. Connect the ...Missing:
Tune Band A (Left) to 2m Simplex or Repeater frequency (VFO or Memory ... Connect Radio (DB-9F) to computer comm port using a straight modem cord with a ...
new discovery. And Kenwood's TM-D700A Data Communicator allows you to do just that. ... station's status (fixed, moving, weather, etc.), as well as its position ...
Loop-O9100 STM1 ADM/TM is an economic compact ... With up to 4 aggregate optical/electrical STM-1 ... Network Element/ Operations System (NE/OS),. NE/NE ...
MANUALE DI ISTRUZIONI : MONITOR VIDEO A COLORI ... Thank you for purchasing this JVC color video monitor. ..... 15. (Front view of TM-H1950CG shown) ...
attached). Are there cards or cables ... on your motherboard or removable processor card, and is near the Intel486 processor. .... moving it up to a 90° angle.
attached). Are there cards or cables ... on your motherboard or removable processor card, and is near the Intel486 processor. .... moving it up to a 90° angle.
Therefore, in âstereoâ mode there are essentially two power amps regardless of ..... For GPS Series amplifiers, the minimum nominal load impedance in bridged ...
Feb 14, 2013 - Tiis iurticle cones the we of diferential corrections on GPS receivers. WHe the example of a Garmin receiver is used the article chordd be ...
revêtement des câbles. • Pour éviter les court-circuits, ne jamais ... imprégné de dissolvant volatile comme un diluant à peinture ou de l'alcool. Il pourrait rayer la ...
lever will not stay down unless the toaster is plugged in). The 'cancel? button will illuminate. • Use the carriage lever to lift the toast to 'Preview' at any time ...
d'endommagement du revêtement des câbles. • Pour éviter les court-circuits, ne jamais mettre ou laisser d'objets métalliques (comme une pièce de monnaie ou ...