KENWOOD TM-D710 SETUP Here are the general settings for the D710A when using the GTRANS cable. This setup can also be used with any GPS by making the appropriate changes to TNC menu items 602 and 603. The SMARTBEACONING menu items and a few other choices are only available with the following D710 firmware update: TNC Version 1.01, OP Panel Version 2.01, Main Version 2.01. These settings can all be tweaked to your liking. First, make sure the current DATE, TIME, and TIME ZONE are set in AUX MENU ITEMS 524, 525 and 526.
TNC MENU SETTINGS Menu #600 BASIC Set the My CALLSIGN to your call sign and SSID (or use tactical call sign) Set the BEACON TYPE to APRS™ Menu #601 TNC Set DATA BAND to A BAND Set DATA SPEED to 1200 bps Set DCD SENSE to D or RxD BAND Set TX DELAY to 200 ms. Menu #602 GPS PORT Set Baud Rate: 4800 bps (Choices are 2400, 4800, 9600) Set INPUT: GPS Set OUTPUT: WAYPOINT (Set to OFF if using a GPS puck) Menu #603 WAYPOINT Set FORMAT: KENWOOD (Choices are KENWOOD, NMEA, MAGELLAN) Set NAME: 9 char (Only 6-7 char can be used with MAGELLAN) Set OUTPUT: ALL Menu #606 BEACON INFORMATION Set SPEED: ON Set ALTITUDE: ON Set AMBIGUITY: OFF Menu #608 STATUS TEXT In the TEXT FIELD, you can enter some text or leave blank. This is where you would place your call sign if you are using a tactical call in the MYCALLSIGN field. You need to set the text transmission rate: 1/1 or 1/3, etc. Remember that your call sign must be sent at least once every ten minutes if using a tactical call. Pressing the MHZ button will put the flashing cursor to the left of a number between 1 and 5. Press USE and an asterisk will be set between the cursor and the number. Pressing MHZ gets you to the sub menu items where you enter the text. Menu #609 PACKET FILTER You might want to set the POSITION LIMIT to something like 50 or 100 miles to keep the noise down. For the TYPE just leave all the selections with an asterisk.
#610 STATION ICON Select OTHERS Then select the appropriate SYMBOL and TABLE. It defaults to KENWOOD. Menu #611 BEACON TX ALGORITHM Set METHOD: AUTO or SMARTBEACONING (Additional SMARTBEACONING settings are in menu #630 and menu #631) Set INITIAL INTERVAL: 2 (The manual only shows 0.2/0.5/1/3/5/10/20/30 minutes but there is a setting for 2 min with the latest firmware) Verify DECAY ALGORITHM: ON Verify PROPORTIONAL PATHING: ON Menu #612 PACKET PATH Set TYPE: Select NEW N-PARADIGM and press USE Set WIDE1-1: Set to ON if you need to use a local digipeater to get to an IGATE Set TOTAL HOPS: Set to 2 unless you have WIDE1-1 on then set to 3 Verify PATH IS VIA: WIDE2-2 or WIDE1-1,WIDE2-2 depending on above settings. Menu #613 NETWORK Verify an asterisk is next to APRS™. Menu #614 VOICE ALERT Verify VOICE ALERT : OFF Menu #615 WEATHER STATION Verify TX : OFF Menu #616 DIGIPEAT (MY CALL) Verify DIGIPEAT: OFF Menu #617 UICHECK Leave as is. Default is TIME: 28 SEC Menu #618 UIDIGI Verify UIDIGI: OFF Menu #619 UIFLOOD Verify UIFLOOD: OFF Menu #620 UITRACE Verify UITRACE: OFF Menu #621 USER PHRASES Here you can put your own messages. Menu #622 AUTO MESSAGE REPLY Verify REPLY: OFF Menu #623 GROUP FILTERING Leave as is. Default is MESSAGE: ALL, QST, CQ, KWD Menu #624 SOUND Adjust to your preference, but to keep the noise down use the following. RX BEEP: OFF TX BEEP (BEACON): OFF SPECIAL CALL: Blank APRS VOICE: OFF
Menu #625 INTERRUPT DISPLAY Set per personal preference Menu #626 DISPLAY UNIT 1 Verify SPEED, DISTANCE: mi/h, mile Verify ALTITUDE, RAIN: feet, inch Verify TEMPERATURE: °F Menu #630 SMARTBEACONING 1 Set LOW SPEED: 5 Set HIGH SPEED: 60 Set SLOW RATE: 10 MIN (600 seconds) Set FAST RATE: 120 SEC Menu #631 SMARTBEACONING 2 You can leave AS IS to begin with, but with the roads in my territory, I prefer: Set TURN ANGLE: 40 DEG Verify SLOPE: 26 (10 DEG/SPEED) Set TURN TIME: 60
Tune Band A (Left) to 2m Simplex or Repeater frequency (VFO or Memory ... Connect Radio (DB-9F) to computer comm port using a straight modem cord with a ...
a. While programming the Kenwood D700 and/or the AVMAP G4T, the communication ... arrows on it) to move the cursor around to choose 'items' and the [+] button to ... NOTE: This can be a little tricky in that your timing has to be good or else ...
Set-up for Kenwood D7A Hand Held with the AVMAP G4T. 1. Kenwood D7A ... knob with the four arrows on it) to move the cursor around to choose 'items' and the [+] ... NOTE: This can be a little tricky in that your timing has to be good or else ...
Configuration with a Serial Terminal program. 5 ... An APRS digipeater is installed on the International Space. Station and ...... Hotel (blue bed icon). \ H. AHz. 40.
Mar 2, 2015 - email addresses rather than personal staff email addresses. Contact details are at the ...... Opens a list with all available docking windows that.
The unit may be reprogrammed by downloading the free Byonics configuration ... order to program the device, the transmitting and receiving serial lines must ... digipath, Smart Beaconing, and other data modes) A pair of holes on the printed circuit b
MHz with the supplied FNB-101LI Lithium-ion battery. The optional FNB-102LI High Capacity Lithium-ion. Battery will provide up to 8.5 hours on 144 MHz, and.
C4FM/FM 144/430 MHz ..... APRS reception pop-up setting. ..... A âping pongâ bell will ring and the âAPRS pop-upâ screen will be displayed for a fixed period of ...
Products, names, logos ... time performance visualization of u-blox GNSS receiver products. u-center ... Structured and graphical data visualization in realtime:.
Apr 28, 2009 - It may consist of a radio, antenna, TNC and GPS but since most of the time the mobile just transmits unconnected UI frames, the receiver part of ...
to set Radio items. iSCAN-II BMW SSS software supports to do the settings on 6 Series E63: 1. Anti-Theft System: to set Interior sensor, Tilt Sensor and other ...
ISL4223E is a 2 driver, 2 receiver device that, coupled with ... Battery Powered, and Portable Equipment. - Hand-Held Products (GPS Receivers, Bar Code.
Sep 9, 2007 - all the terms and conditions under either Agreement or the END .... DVSI neither represents that a license is not required nor that, if required, it will ... 5.3.4. Framed Output: Words 2-6 : Rate Information. 33. 5.3.5 .... interface t
MC68HC908KX8 ⢠MC68HC908KX2 ⢠MC68HC08KX8 Data Sheet, Rev. 2.1. Freescale ... Revision to the description of the CHxMAX bit and the note that follows ... 17.5 5.0-Vdc DC Electrical Characteristics and â Corrected footnote for VDD supply ... Sec
INSTRUCTION MANUAL. 144/440 MHz ...... thereafter. When the Internal GPS receiver is On, pressing [POS] will ...... become available in the future. â¡ Packet ...
Mar 16, 2015 - u-blox reserves all rights to this document and the information ..... AssistNow Online fixed (reported wrong username/password) .... o Make download button the default. ⢠Add 3D button and support in Google Earth View.
Mar 16, 2006 - Save Critical Data with Block Lock⢠Memory. - Protect 1/4, 1/2, all or ..... VTRIP value for 200ms (nominal) the circuit releases. RESET/RESET ...
switching to the APRS Alternate Symbol Table, or adding an overlay character. ... TinyTrak3 can send a text beacon message after periodic location transmissions. .... This button will download all configuration settings entered in the software ...
If the book was of use to you I would love to know. Enjoy! ... So What can this thing really do? x. Navigation system ... Quite impressive if you ask me. The only ... back of the tracker 2. ... Again, scot has made it relatively easy to config- ure y