Protective gloves should be ised when it is handled. Halogen ... Twist-mount the alignement lamp instead of the cross hair in the transmitter. Transmitter side.
1. HL 3002 1.1 General Sometimes the visibility in the measurement path is poor. The reason for this might be high dust load, smoke or strong ambient light from the process (as in a combustion chamber). In this case a stronger light source must be used in the first alignement step. Siemens Laser Analytics AB can supply a suitable light source labelled HL 3000. This is a point source using a 50 W halogen lamp and will produce a very luminous light spot normally easy to spot in the alignement procedure.
1
HL 3002
LDS 3000 Operators manual
1.2 The alignement procedure The sensor is aligned using the sensor alignment kit AK 3002 together with HL 3000. The aligning procedure is as follows: Receiver side 1. Start by aligning the transmitter side. This is done by removing the receiver at the quick connect interface and instead mount HL 3000 which defines the optical axis of the sensor pair. While the receiver is dismounted - check that the lens is clean on the receiver and that the purging is working.
Halogen alignement lamp
Receiver side
HL 3000 generates a considerable amount of heat. Protective gloves should be ised when it is handled.
2
Note!
LDS 3000 Operators manual
HL 3002
Transmitter side 2. Dismount the transmitter and check that the lens is clean on the transmitter and that the purging is working. Then mount the transmitter and twist-dismount the launcher (fiber cable connector in the middle), twist-mount the cross hair instead. Align with the four bolts on the flange, the light dot must be centred in the inner ring of the cross hair.
Alignement screws
Cross hair
Transmitter side
3
HL 3002
LDS 3000 Operators manual
Transmitter side 3. Twist-mount the alignement lamp instead of the cross hair in the transmitter.
Alignement lamp Transmitter side
4
LDS 3000 Operators manual
HL 3002
Receiver side 4. Mount the receiver back again and twist-mount the cross hair instead of the detector module. Align with the four bolts on the flange, the light dot must be centred in the inner ring of the cross hair.
Alignement screws
Cross hair
Receiver side
CD 3002 is now aligned and the holder for the fibre connector and the detector module should be mounted in their places. Finally, instrument air, or which ever method is used to protect the optical surfaces, should be connected to the appropriate inlets both at the transmitter and receiver side of the sensor. The mechanical stability of the sensor mechanics is sufficient to allow dismounting (the quick connection) of both the receiver and the transmitter. This means that cleaning of the lenses does not require re-alignment of the sensor.
Slide the sensor card into its holder on the calibration cell module and connect the power cable from the DC/DC card. Insert the detector mod- ule into the hole ...
tected mode should be done by trained service technicians. Malfunction due to faulty settings are not covered by the warranty. 3.1 Temperature setting.
the American Society for Heating, Refrigeration and Air. Conditioning .... Pre-Planning Your Installation - Important: The recommended height to install this hood.
When cutting or drilling into wall or ceiling, do not dam- ... backward cold air flow and a nonmetallic thermal break should ... The damper should be on the cold.
settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on ... Start the rangehood several minutes before cooking to develop.
Allow a 15-minute warm-up period. CAUTION: Use isolation transformer or observe polarity when connecting te. | Maintain line voltage at 120V AC. Adjustments ...
Jan 14, 2003 - the same amount on light on half the surface. The prices range from 20 to 25 US $, they are waterproof to 30 meters, they come in Green, Blue, ...
source, two flanges and an aiming tool. The light source is a ... process flange (which will be the case when the first flange is aligned). Halogen light source.
devices that use a wireless remote control, such as televisions. If interference occurs, move the product away from the device, plug the product or device.
housing (included in the outfit BEECH):. Groundglass .................. NAOTZ. Blue glass (produces illumination resembling daylight; its colour may be further varied ...
Determine if fluorescent light bulbs are operational prior to installation or removal. ⢠Verify voltage presence without the need for another tool. ⢠Increase ...
Application Note: Consult your local fire code authorities .... RING. Page 8 of 30. 939500548 Rev B. NOTE: The Shade and. Diffuser are packaged folded up.
The most recent version of the CapacitiveSensor library is here: http://www.arduino.cc/capacitive. Download the file to your computer and unzip it. Open your ...
Replacement Parts and Accessories. Pieces de rechange et accessoires. Universal end cap for T-12, 2260 series. Heat sink screen for HO and VHO lamp bases.
For off-road use only. Bulb Care: Do not handle the glass part of a halogen bulb. The oil from your hands or any other residue on the glass can cause the bulb to ...
le cid par pierre | Read & Download Ebook le cid par pierre for free at our Online Library. le cid par pierre PDF eBook. LE CID PAR PIERRE. LE CID PAR ...
Read and Save Ebook le cid esquisse littacraire par m as PDF for free at Online Ebook Library. Get le cid esquisse littacraire par m. PDF file for free from our ...
