C 192.168.5.0/24 is directly connected, Serial0. Router#show protocol. Global values: Internet Protocol routing is enabled. Ethernet0 is up, line protocol is up.
TP4 : Routeurs Cisco Module TR2 Objectif : faire une interconnexion WAN
Configuration client ip link set down dev eth0 ip a d 10.40.211.9/8 dev eth0 ip a a 192.168.X.Y/16 dev eth0
ex : 192.168.101.4
Configuration pc connecté au routeur DCE : ''Master'' DTE : ''Slave'' minicom => ctrl+A => Z => O =>configuration des ports série A => /dev/ttyS0 E => E : 9600 Enregistrer config par défaut router> enable
Configuration routeur mathieu Router#enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#interface Ethernet0 Router(config‐if)#ip address 192.168.104.1 255.255.255.0 Router(config‐if)#no shutdown Router(config)#^Z Router#write Building configuration... SANCHEZ David RT2 B1 TR2-TP4-Routeurs-Cisco
08/01/2008 1/2
[OK] Router#configure terminal Router(config)#interface Serial0 Router(config‐if)#ip address 192.168.5.1 255.255.255.0 Router(config‐if)#no shutdown Router(config‐if)#clock rate 8000000 Router(config)#^Z Router#write [OK] Router#configure terminal Router(config)#interface Serial1 Router(config‐if)#ip address 192.168.4.2 255.255.255.0 Router(config‐if)#no shutdown Router(config‐if)#clock rate 1200 Router(config)#^Z Router#write [OK] Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#ip routing // Activer le routage Router(config)#router static Router#show ip route Codes: C ‐ connected, S ‐ static, I ‐ IGRP, R ‐ RIP, M ‐ mobile, B ‐ BGP D ‐ EIGRP, EX ‐ EIGRP external, O ‐ OSPF, IA ‐ OSPF inter area N1 ‐ OSPF NSSA external type 1, N2 ‐ OSPF NSSA external type 2 E1 ‐ OSPF external type 1, E2 ‐ OSPF external type 2, E ‐ EGP i ‐ IS‐IS, L1 ‐ IS‐IS level‐1, L2 ‐ IS‐IS level‐2, * ‐ candidate default U ‐ per‐user static route, o ‐ ODR
Gateway of last resort is not set C 192.168.104.0/24 is directly connected, Ethernet0 C 192.168.4.0/24 is directly connected, Serial1 C 192.168.5.0/24 is directly connected, Serial0 Router#show protocol Global values: Internet Protocol routing is enabled Ethernet0 is up, line protocol is up Internet address is 192.168.104.1/24 Serial0 is up, line protocol is up Internet address is 192.168.5.1/24 Serial1 is up, line protocol is up Internet address is 192.168.4.2/24 SANCHEZ David RT2 B1 TR2-TP4-Routeurs-Cisco
R 192.168.5.0/24 [120/1] via 192.168.6.1, 00:00:18, Serial1. C 192.168.6.0/24 is directly connected, Serial1. C 192.168.1.0/24 is directly connected, Serial0.
C 192.168.5.0/24 is directly connected, Serial0. Router#show protocol. Global values: Internet Protocol routing is enabled. Ethernet0 is up, line protocol is up.
Q. What is Cisco® Unified MobilityManager? A. Cisco Unified MobilityManager is an enterprise mobility application that works with Cisco Unified CallManager to ...
Application Programming Interface (JTAPI) application, and it runs on a ... The Cisco Disaster Recovery System (DRS), a backup and restore utility, is included.
How do I know which Cisco IOS software release supports a particular BGP feature? ... What is the default BGP ConnectRetry timer, and is it possible to tune the ..... The number of routes in VPN routing/forwarding (VRF) exceeds the route-limit config
second thanks to a GPS module. ® It calculates the route to follow and compares it to the heading thanks to a compass. ® It estimates the drift due to the wind ...
Aug 2, 2005 - between human-immune system and computer security, we will reuse some of the ..... specialized organizations need to make a more intensive advertising about the ..... Besides, according to a survey of Marcus J.Ranum for ICSA Labs in 200
(ToS/DSCP) traffic prioritization settings. ⢠Dual Port capability for network element prequalification testing. ⢠Control/Respond Loopback feature to loop-up/down.
I play basketball. Je joue au hockey sur glace. I play ice hockey. Je joue au tennis. I play tennis. Je joue au volley. I play volleyball. Des verbes utiles avec ânousâ.
2006 Sunrise Telecom Incorporated. All rights reserved. Specifications subject to change without notice. All product and company names are trademarks of their ...
Networking (LAN, Ad hoc, ...) 18. Rendering (Printing, Speaker, ...) .... attempt to connect to the one reporting the lowest load. 4. 3. 2. Minor Device Class bit no of ...
The MTT-38 SDH/SONET Module, part of the Modular Test Toolkit (MTT) family of products, is ... ASCII decode of 16-byte or 64-byte HP/STS or LP/VT path trace.
To decompress the software, create a directory on the hard disk and transfer file ZIP.EXE into this directory. ..... CMD command file to start several applications.
6. CoNSeiLS D'UTiLiSATioN. moDULe 1. Ãtape 1 entrer en contact. â Saluer quelqu' ... b Les apprenants s'initient à la description d'une pro- fession. c Le jeu ...
AT command mode, user can configure the module and send control .... Example: Set serial port parameters to 115200, 2 bits stop bit, and even ... AT+MPIO?
and lock service panel to prevent power from being switched on accidentally ... 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and ...
