DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E
RMT-808/809/811/812
SERVICE MANUAL
Ver 1.3 2003. 06
Level 2
US Model Canadian Model Korea Model DCR-TRV6/TRV11/TRV20
AEP Model UK Model Australian Model Chinese Model DCR-TRV6E/TRV11E/TRV20E
E Model Hong Kong Model Tourist Model Photo : DCR-TRV20E RMT-811
DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E
J MECHANISM On the VC-240/241 board This service manual provides the information that is premised the circuit board replacement service and not intended repair inside the VC-240/241 board. Therefore, schematic diagram, printed wiring board and electrical parts list of the VC-240/241 board are not shown. The following pages are not shown. Schematic diagram .......................... Pages 4-17 to 4-66 Printed wiring board ......................... Pages 4-67 to 4-74 Electrical parts list ............................ Pages 6-23 to 6-44
For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL ADJUSTMENT MANUAL J MECHANISM ” (9-929-807-11). DCR-TRV6/TRV11/TRV20 : NTSC model DCR-TRV6E/TRV11E/TRV20E : PAL model
• Table showing differences is shown on page 4.
SPECIFICATIONS
— Continued on next page —
DIGITAL VIDEO CAMERA RECORDER
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1.
2. 3.
Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering.
—2—
• Table showing differences is shown on page 4.
• SUPPLIED ACCESSORIES Check that the following accessories are supplied with your camcorder.
1 Wireless Remote Commander (1) RMT-808: DCR-TRV6/TRV6E: AUS, E, JE, CN RMT-809: DCR-TRV6E: AEP, UK RMT-812: DCR-TRV11E: AEP, UK RMT-811: DCR-TRV11/TRV11E: AUS, E, HK, JE, CN/TRV20/ TRV20E
8 Shoulder strap (1)
2 R6 (size AA) battery for Remote Commander (2)
qa Application software: PictureGear 4.1Lite (CD ROM) (1) DCR-TRV11/TRV11E/TRV20/TRV20E only
3 AC-L10A/L10B/L10C AC power adaptor (1), Mains lead (1) 4 NP-FM50 battery pack (1) 5 PC serial cable (1) DCR-TRV11/TRV11E/TRV20/TRV20E only 6 “Memory Stick” (1) DCR-TRV11/TRV11E/TRV20/TRV20E only 7 A/V connecting cable (1)
9 21-pin adaptor (1) DCR-TRV6E: AEP, UK/TRV11E: AEP, UK/TRV20E: AEP, UK 0 Lens cap (1)
qs Lens hood (1) DCR-TRV20/TRV20E only qd 2-pin conversion adaptor (1) DCR-TRV6E: E, HK/TRV6E: E, HK/TRV11: E, HK/ TRV11E: E, HK/TRV20: E, HK/TRV20E: E, HK qf 2-pin conversion adaptor (1) DCR-TRV6: JE/TRV6E: JE/TRV11: JE/TRV11E: JE/ TRV20: JE/TRV20E: JE
• Abbreviation CND : Canadian model CN : Chinese model HK : Hong Kong model KR : Korea model AUS : Australian model JE : Tourist model
—3—
—4—
a 2.5 200k
MEMORY STICK slot DIGITAL I/O (RS232C) LINE IN LCD (size) LCD (pixel)
NTSC PAL
PAL
DCRTRV11E E, AUS, HK, CN, JE
2.5 200k
960H
a 2.5 200k
960H a a a 3.5 184k
a a
a a a 3.5 184k 3.5 184k
960H
960H
960H
a
a
a
• Abbreviation CND : Canadian model CN : Chinese model HK : Hong Kong model
KR : Korea model AUS : Australian model JE : Tourist model
PD-123
PD-124
PD board
a
113k
CK-92
a
113k
CK-94
a
113k
VC-241
113k
113k
113k
CK board
VC board
EVF (pixel) CD-252 board FP-219 flexible
PAL
DCRDCRTRV11 TRV11E US,CND, AEP, UK E, HK, JE, KR NTSC PAL
DCRDCRTRV20 TRV20E US,CND, AEP, UK E,HK,JE, KR PAL
DCRTRV20E E, AUS, HK, CN, JE
a a a 3.5 246k
1152H a a a 3.5 246k
1152H a a a 3.5 246k
1152H
180k a
180k a
PD-124
CK-94
VC-240
180k a
TYPE ST TYPE ST TYPE ST TYPE SH TYPE SH TYPE SH TYPE CA TYPE ST TYPE ST
960H
LCD type
PAL
DCRTRV6E E, AUS, HK, CN, JE
RMT-808 RMT-809 RMT-808 RMT-811 RMT-812 RMT-811 RMT-811 RMT-811 RMT-811 10× 10× 10× 10× 10× 10× 10× 10× 10× 120× 120× 40× 40× 40× 120× 120× 120× 120×
NTSC
CCD imager
Remote commander Lens Digital zoom
Color system
Table for difference of function DCRDCRModel TRV6 TRV6E US,CND, AEP, UK Destination E, HK, JE, KR
a: with 1152H CCD imager. a: with 960H CCD imager. VC-240: with 1152H CCD imager. VC-241: with 960H CCD imager. CK-92: with LCD TYPE CA or TYPE SH. CK-94: with LCD TYPE ST. PD-123: with LCD TYPE CA or TYPE SH. PD-124: with LCD TYPE ST.
TYPE CA, TYPE SH: with PD-123 board. TYPE ST: with PD-124 board.
1152H : with VC-240 board. 960H : with VC-241 board. a: with IC1406 to IC1412 of VC-240 board or with IC1402 to IC1407 of VC-241 board. a: with REC button and IC903 of VC-240/241 board.
NTSC: X101 is 66MHz (DCR-TRV20) X701 is 36MHz (DCR-TRV6/TRV11) PAL: X101 is 54MHz (DCR-TRV20E) X701 is 36MHz (DCR-TRV6E/TRV11E)
Remark
TABLE OF CONTENTS SERVICE NOTE 1. 2.
POWER SUPPLY DURING REPAIRS ····························· 8 TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ································································ 8
SELF-DIAGNOSIS FUNCTION 1. 2. 3. 3-1. 3-2. 3-3. 4.
SELF-DIAGNOSIS FUNCTION ······································· 9 SELF-DIAGNOSIS DISPLAY ·········································· 9 SERVICE MODE DISPLAY ············································· 9 Display Method ·································································· 9 Switching of Backup No. ··················································· 9 End of Display ···································································· 9 SELF-DIAGNOSIS CODE TABLE ································· 10
1.
GENERAL
Checking supplied accessories ·················································· 1-1 Quick Start Guide ······································································ 1-1 Getting started ··········································································· 1-2 Using this manual ·································································· 1-2 Step 1 Preparing the power supply ········································ 1-2 Installing the battery pack ···················································· 1-2 Charging the battery pack ···················································· 1-3 Connecting to the mains ······················································ 1-4 Step 2 Inserting a cassette ······················································ 1-4 Recording –Basics ····································································· 1-4 Recording a picture ································································ 1-4 Shooting backlit subjects (BACK LIGHT) ·························· 1-7 Shooting in the dark (NightShot/Super NightShot) ············· 1-7 Checking the recording – END SEARCH/ EDIT SEARCH/Rec Review ··············································· 1-8 Playback –Basics ······································································· 1-8 Playing back a tape ································································ 1-8 Viewing the recording on TV ················································ 1-9 Advanced Recording Operations ············································· 1-10 Recording a still image on a tape –Tape Photo recording ··· 1-10 Adjusting the white balance manually ································· 1-11 Using the wide mode ··························································· 1-12 Using the fader function ······················································ 1-12 Using special effects –Picture effect ···································· 1-13 Using special effects –Digital effect ···································· 1-14 Using the PROGRAM AE function ····································· 1-14 Adjusting the exposure manually ········································ 1-15 Focusing manually ······························································· 1-15 Advanced Playback Operations ··············································· 1-16 Playing back a tape with picture effects ······························ 1-16 Playing back a tape with digital effects ······························· 1-16 Enlaring images recorded on tapes –PB ZOOM ················· 1-17 Quickly locating a scene using the zero set memory function ················································································ 1-17 Searching the boundaries of recorded tape by title –Title search ········································································· 1-17 Searching a recording by date –Date search ························ 1-18 Searching for a photo –Photo search/Photo scan ················· 1-18 Editing ····················································································· 1-19 Dubbing a tape ····································································· 1-19 Dubbing only desired scenes –Digital programme editing ···· 1-20 Using with analog video unit and PC – Signal convert function ····················································· 1-23 Recording video or TV programmes ··································· 1-23 Inserting a scene from a VCR –Insert editing ······················ 1-24 Audio dubbing ····································································· 1-25 Superimposing a title ··························································· 1-26 Making your own titles ························································ 1-27 Labeling a cassette ······························································· 1-28 Customizing Your Camcorder ················································· 1-28 Changing the menu settings ················································· 1-28 Resetting the date and time ·················································· 1-30
“Memory Stick” Operations ···················································· 1-30 Using a “Memory Stick” –introduction ······························· 1-30 Recording still images on “Memory Stick”s –Memory photo recording ··················································· 1-32 Superimposing a still picture in a “Memory Stick” on a moving picture –MEMORY MIX ································ 1-34 Recording an image from a mini DV tape as a still image ·· 1-35 Copying still images from a mini DV tape –Photo save ······ 1-36 Viewing a still picture –Memory photo playback ················ 1-36 Copying the image recorded on “Memory Stick”s to mini DV tapes ······································································ 1-37 Enlarging still images recorded on “Memory Stick”s –Memory PB ZOOM ···························································· 1-38 Playing back images in a continuous loop –SLIDE SHOW ··· 1-38 Preventing accidental erasure –Image protection ················ 1-39 Deleting images ··································································· 1-39 Writing a print mark –PRINT MARK ································· 1-40 Additional Information ···························································· 1-40 Usable cassettes ··································································· 1-40 About i.LINK ······································································· 1-41 Troubleshooting ··································································· 1-42 Self-diagnosis display ·························································· 1-43 Warning indicators and messages ········································ 1-43 Using your camcorder abroad ·············································· 1-44 Maintenance information and precautions ··························· 1-44 Quick Reference ······································································ 1-45 Identifying the parts and controls ········································ 1-45
2.
DISASSEMBLY
2-1. LCD SECTION-1 (TRV6/TRV6E MODEL) (PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) ·················· 2-2 2-2. LCD SECTION-2 (TRV11/TRV11E/TRV20/TRV20E MODEL) (PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) ········ 2-3 2-3. EVF SECTION (LB-64 BOARD) ··································· 2-4 2-4. FRONT PANEL BLOCK ASSEMBLY (MA-385 BOARD), CABINET (R) BLOCK ASSEMBLY ····························· 2-5 2-5. CK-92/94 BOARD, SPEAKER, CONTROL SWITCH BLOCK (CF30150) ····················· 2-6 2-6. DD-137 BOARD, EVF BLOCK ASSEMBLY, BT PANEL SECTION ···················································· 2-7 2-7. LENS SECTION-1 (LENS DEVICE, FP-219 FLEXIBLE BOARD) (TRV6/TRV6E/TRV11/TRV11E MODEL) ···················· 2-8 2-8. LENS SECTION-2 (LENS DEVICE, CD-252 BOARD) (TRV20/TRV20E MODEL) ············································ 2-8 2-9. VC-240/241 BOARD, MECHANISM DECK ················ 2-9 2-10. CONTROL SWITCH BLOCK (FK30150) ··················· 2-10 2-11. JK-188 BOARD, CONTROL SWITCH BLOCK (PS30150) ······································································ 2-10 2-12. MEMORY STICK CONNECTOR (TRV11/TRV11E/TRV20/TRV20E) ····························· 2-11 2-13. HINGE ASSEMBLY, LCD HARNESS PROCESSING · 2-12 2-14. CIRCUIT BOARDS LOCATION ································· 2-13 2-15. FLEXIBLE BOARDS LOCATION ······························ 2-14
3.
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV6/TRV6E) ······················································ 3-1 3-2. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV11/TRV11E) ·················································· 3-3 3-3. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV20/TRV20E) ·················································· 3-5 3-4. OVERALL BLOCK DIAGRAM (2/3) ··························· 3-7
—5—
3-5. OVERALL BLOCK DIAGRAM (3/3) ··························· 3-9 3-6. POWER BLOCK DIAGRAM (1/2) ······························ 3-11 3-7. POWER BLOCK DIAGRAM (2/2) (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 3-13 3-8. POWER BLOCK DIAGRAM (2/2) (DCR-TRV20/TRV20E) ················································ 3-15
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM-1 ···························· 4-1 FRAME SCHEMATIC DIAGRAM-2 ···························· 4-3 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS ············································ 4-5 • NS-10 (SUPER NIGHTSHOT SW) PRINTED WIRING BOARD ························· 4-6 • CD-252 (CCD IMAGER) PRINTED WIRING BOARD ························· 4-7 • CD-252 (CCD IMAGER) SCHEMATIC DIAGRAM ···························· 4-11 • FP-219 FLEXIBLE BOARD (CCD IMAGER) SCHEMATIC DIAGRAM ···························· 4-13 • FP-219 FLEXIBLE BOARD (CCD IMAGER) PRINTED WIRING BOARD ······················· 4-15 Shematic diagram and printed wiring board of the VC-240/241 board are not shown. Pages from 4-17 to 4-74 are not shown. • CK-92 (KEY) PRINTED WIRING BOARD ······················· 4-75 • FP-181 FLEXIBLE BOARD (PANEL REVERSE) PRINTED WIRING BOARD ······················· 4-78 • CK-94 (KEY) PRINTED WIRING BOARD ······················· 4-79 • CK-92/94 (KEY) SCHEMATIC DIAGRAM ···························· 4-83 • LB-64 (EVF BACK LIGHT) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ···························· 4-85 • JK-188 (A/V IN/OUT) PRINTED WIRING BOARD ······················· 4-87 • JK-188 (A/V IN/OUT) SCHEMATIC DIAGRAM ···························· 4-89 • CONTROL SWITCH BLOCK (FK-30150) SCHEMATIC DIAGRAM ···························· 4-91 • PD-123 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD ······················· 4-92 • PD-123 (LCD DRIVE)(1/2) SCHEMATIC DIAGRAM ···························· 4-93 • PD-123 (RGB DRIVE)(2/2) SCHEMATIC DIAGRAM ···························· 4-95 • PD-124 (LCD DRIVE)(1/2) SCHEMATIC DIAGRAM ···························· 4-97 • PD-124 (RGB DRIVE)(2/2) SCHEMATIC DIAGRAM ···························· 4-99 • PD-124 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD ····················· 4-101 • SE-107 (MANUAL FOCUS) PRINTED WIRING BOARD ····················· 4-102 • MA-385 (AUDIO I/O) PRINTED WIRING BOARD ····················· 4-103 • MA-385 (AUDIO I/O) SCHEMATIC DIAGRAM ·························· 4-105 • DD-137 (DC/DC CONVERTER)(1/2) SCHEMATIC DIAGRAM ·························· 4-107 • DD-137 (DC/DC CONVERTER)(2/2) SCHEMATIC DIAGRAM ·························· 4-109
• DD-137 (DC/DC CONVERTER)(1/2) PRINTED WIRING BOARD ····················· 4-111 4-3. WAVEFORMS ···························································· 4-113 4-4. MOUNTED LOCATION ············································ 4-125
5 1. 1-1. 5-1. 1-1.
ADJUSTMENTS
Before starting adjustment ··············································· 5-1 Adjusting items when replacing main parts and boards. ··· 5-2 CAMERA SECTION ADJUSTMENT ··························· 5-6 PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) ··················································· 5-6 1-1-1. List of Service Tools ························································ 5-6 1-1-2. Preparations ····································································· 5-7 1-1-3. Precaution ········································································ 5-9 1. Setting the Switch ···························································· 5-9 2. Order of Adjustments ······················································ 5-9 3. Subjects ··········································································· 5-9 1-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA ··· 5-10 1-2-1. INITIALIZATION OF C, D, 8 PAGE DATA ················ 5-10 1. Initializing the C, D, 8 Page Data ·································· 5-10 2. Modification of C, D, 8 Page Data ································ 5-10 3. C Page Table ·································································· 5-10 4. D Page Table ·································································· 5-12 5. 8 Page Table ··································································· 5-13 1-2-2. INITIALIZATION OF B PAGE DATA (DCR-TRV11/TRV11E/TRV20/TRV20E) ···················· 5-14 1. Initializing the B Page Data (DCR-TRV20/TRV20E) ·· 5-14 2. Modification of B Page Data (DCR-TRV20/TRV20E) ·· 5-14 3. Initializing the B Page Data (DCR-TRV11/TRV11E) ·· 5-14 4. Modification of B Page Data (DCR-TRV11/TRV11E) ·· 5-14 5. B Page Table ·································································· 5-15 1-2-3. INITIALIZATION OF E, F, 7 PAGE DATA ················· 5-15 1. Initializing the E, F, 7 Page Data ··································· 5-15 2. Modification of E, F, 7 Page Data ································· 5-15 3. F Page Table ·································································· 5-16 4. E Page Table ·································································· 5-18 5. 7 Page Table ··································································· 5-19 1-3. CAMERA SYSTEM ADJUSTMENTS ························ 5-20 1. 36MHz Origin Oscillation Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E)(VC-241 board) ·· 5-20 2. 54MHz/66MHz Origin Oscillation Adjustment (DCR-TRV20/TRV20E)(CD-252 board) ······················ 5-20 3. Zoom Key Center Adjustment ······································· 5-21 4. HALL Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-21 5. HALL Adjustment (DCR-TRV20/TRV20E) ················· 5-22 6. MR Adjustment (DCR-TRV20/TRV20E) ····················· 5-22 7. Flange Back Adjustment (Using Minipattern Box) ··············································· 5-23 8. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) ·································· 5-24 8-1. Flange Back Adjustment (1) ·········································· 5-24 8-2. Flange Back Adjustment (2) ·········································· 5-24 9. Flange Back Check ························································ 5-25 10. Optical Axis Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-26 11. Picture Frame Setting ···················································· 5-27 12. Color Reproduction Adjustment ···································· 5-28 13. MAX GAIN Adjustment ··············································· 5-29 13-1. MAX GAIN Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-29 13-2. MAX GAIN Data Input (DCR-TRV20/TRV20E) ········· 5-29 14. Auto White Balance & LV Standard Data Input ··········· 5-29 15. Auto White Balance Adjustment ··································· 5-30 16. White Balance Check ···················································· 5-31 17. Mechanical Shutter Adjustment ···································· 5-31
—6—
17-1. Mechanical Shutter Data Input (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-31 17-2. Mechanical Shutter Data Input (DCR-TRV20/TRV20E) ················································ 5-32 18. Angular Velocity Sensor Sensitivity Adjustment ·········· 5-32 1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT ····························································· 5-33 1. VCO Adjustment (VC-240/241 board) ························· 5-33 2. RGB AMP Adjustment (VC-240/241 board) ················ 5-34 3. Contrast Adjustment (VC-240/241 board) ···················· 5-34 4. Backlight Consumption Current Adjustment (VC-240/241 board) ······················································ 5-35 5. White Balance Adjustment (VC-240/241 board) ·········· 5-35 1-5. LCD SYSTEM ADJUSTMENT ··································· 5-36 1-5-1. LCD SYSTEM ADJUSTMENT (DCR-TRV11/TRV11E/TRV20) ··································· 5-36 1. VCO Adjustment (PD-123 board) ································· 5-36 2. RGB AMP Adjustment (PD-123 board) ························ 5-37 3. Contrast Adjustment (PD-123 board) ···························· 5-37 4. V-COM Level Adjustment (PD-123 board) ·················· 5-38 5. V-COM Adjustment (PD-123 board) ···························· 5-38 6. White Balance Adjustment (PD-123 board) ·················· 5-39 1-5-2. LCD SYSTEM ADJUSTMENT (DCR-TRV6/TRV6E/TRV20E) ····································· 5-39 1. VCO Adjustment (PD-124 board) ································· 5-39 2. Bright Adjustment (PD-124 board) ······························· 5-40 3. Black Limit Adjustment (PD-124 board) ······················ 5-40 4. Contrast Adjustment (PD-124 board) ···························· 5-41 5. Center Level Adjustment (PD-124 board) ····················· 5-41 6. V-COM Adjustment (PD-124 board) ···························· 5-42 7. White Balance Adjustment (PD-124 board) ·················· 5-42 5-2. MECHANISM SECTION ADJUSTMENT ·················· 5-43 2-1. HOW TO ENTER RECORD MODE WITHOUT CASSETTE ··································································· 5-43 2-2. HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE ··································································· 5-43 2-3. TAPE PATH ADJUSTMENT ········································ 5-43 1. Preparation for Adjustment ··········································· 5-43 2. Procedure after operations ············································· 5-43 5-3. VIDEO SECTION ADJUSTMENTS ··························· 5-44 3-1. PREPARATIONS BEFORE ADJUSTMENTS ············ 5-44 3-1-1. Equipment Required ······················································ 5-44 3-1-2. Precautions on Adjusting ··············································· 5-45 3-1-3. Adjusting Connectors ···················································· 5-46 3-1-4. Connecting the Equipment ············································ 5-46 3-1-5. Checking the Input Signals (Except AEP/UK model) ··· 5-46 3-1-6. Alignment Tapes ···························································· 5-47 3-1-7. Input/Output Level and Impedance ······························· 5-47 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 5-48 1. Initialization of B, C, D, E, F, 7, 8 Page Data ··············· 5-48 2. Serial No. Input ····························································· 5-48 2-1. Company ID Input ························································· 5-48 2-2. Serial No. Input ····························································· 5-48 3. Battery End Check (VC-240/241 board) ······················· 5-50 3-3. SERVO AND RF SYSTEM ADJUSTMENT ··············· 5-51 1. Cap FG Duty Adjustment (VC-240/241 board) ············ 5-51 2. PLL f0 & LPF f0 Adjustment (VC-240/241 board) ······· 5-51 3. Switching Position Adjustment (VC-240/241 board) ··· 5-52 4. AGC Center Level and APC & AEQ Adjustment ········· 5-52 4-1. Preparations before adjustments ···································· 5-52 4-2. AGC Center Level Adjustment (VC-240/241 board) ···· 5-52 4-3. APC & AEQ Adjustment (VC-240/241 board) ············· 5-53 4-4. Processing after Completing Adjustments ···················· 5-53 5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board) ······················································ 5-53 3-4. VIDEO SYSTEM ADJUSTMENTS ····························· 5-54 3-4-1. Base Band Block Adjustments ······································ 5-54
1. 2.
Chroma BPF f0 Adjustment (VC-240/241 Board) ········ 5-54 S VIDEO OUT Y Level Adjustment (VC-240/241 Board) ······················································ 5-54 3. S VIDEO OUT Chroma Level Adjustment (VC-240/241 Board) ······················································ 5-55 4. AV OUT Y, Chroma Level Check (VC-240/241 Board) ·· 5-55 3-4-2. BIST Check ··································································· 5-56 1. Playback System Check ················································ 5-56 1-1. Preparations for Playback ·············································· 5-56 1-2. IC301 TRX (RF) PB BIST Check ································· 5-56 1-3. IC301 AUD (ABUS) PB BIST Check ··························· 5-56 1-4. IC301 VFD PB BIST Check ········································· 5-56 1-5. IC301 ENCODER BIST Check ···································· 5-57 1-6. Processing after Completing Playback System Check ·· 5-58 2. Recording System Check ·············································· 5-59 2-1. Preparations for recording ············································· 5-59 2-2. IC301 TRX (RF) BIST Check ······································· 5-59 2-3. Processing after Completing Recording System Check ·· 5-59 3-5. IR TRANSMITTER ADJUSTMENTS ························· 5-60 1. IR Video Carrier Frequency Adjustment (VC-240/241 board) ······················································ 5-60 2. IR Video Deviation Adjustment (VC-240/241 board) ··· 5-60 3. IR Audio Deviation Adjustment (VC-240/241 board) ·· 5-61 3-6. AUDIO SYSTEM ADJUSTMENTS ···························· 5-62 1. Playback Level Check ··················································· 5-63 2. Overall Level Characteristics Check ····························· 5-63 3. Overall Distortion Check ··············································· 5-63 4. Overall Noise Level Check ············································ 5-63 5. Overall Separation Check ·············································· 5-63 5-4. SERVICE MODE ·························································· 5-64 4-1. ADJUSTMENT REMOTE COMMANDER ················ 5-64 1. Using the adjustment remote commander ····················· 5-64 2. Precautions upon using the adjustment remote commander ···································································· 5-64 4-2. DATA PROCESS ··························································· 5-65 4-3. SERVICE MODE ·························································· 5-66 1. Setting the Test Mode ···················································· 5-66 2. Emergence Memory Address ········································ 5-66 2-1. EMG Code (Emergency Code) ····································· 5-66 2-2. MSW Code ···································································· 5-67 3. Bit value discrimination ················································ 5-68 4. Switch check (1) ···························································· 5-68 5. Switch check (2) ···························································· 5-69 6. Record of Use check ······················································ 5-69
6.
REPAIR PARTS LIST
6-1-1. FRONT PANEL BLOCK ASSEMBLY AND BATTERY PANEL SECTION ········································ 6-1 6-1-2. CABINET (R) BLOCK ASSEMBLY ····························· 6-2 6-1-3. LCD BLOCK ASSEMBLY (TRV6/TRV6E MODEL) ··· 6-3 6-1-4. LCD BLOCK ASSEMBLY (TRV11/TRV11E/TRV20/TRV20E MODEL) ················ 6-4 6-1-5. CABINET (L) SECTION ················································ 6-5 6-1-6. CABINET (L) SECTION-2 ············································ 6-6 6-1-7. LENS BLOCK ASSEMBLY AND EVF BLOCK ASSEMBLY ············································· 6-7 6-1-8. CASSETTE COMPARTMENT AND DRUM BLOCK ASSEMBLY ········································· 6-8 6-1-9. LS CHASSIS ASSEMBLY ············································· 6-9 6-1-10. MECHANISM CHASSIS BLOCK ASSEMBLY ······ 6-10 6-2. ELECTRICAL PARTS LIST ········································ 6-11 Parts list of the VC-240/241 board are not shown. Pages from 6-23 to 6-44 are not shown. * Optical axis frame and color reproduction frame are shown on page 247 to 249.
—7—
SERVICE NOTE 1.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1. Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side. Method 2. Use the DC IN terminal. (Use the AC power adaptor (AC-L10, AC-VQ800 etc. ))
2. 1 2 3 4 5 6 7 8 9 0 qa
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) Refer to 2-4. to remove the top cabinet assembly. Refer to 2-4. to remove the front panel block assembly. Refer to 2-4. to remove the cabinet (R) block assembly. Refer to 2-6. to remove the battery panel section. Refer to 2-6. to remove the VC heat sink. (DCR-TRV20/TRV20E model only) Refer to 2-6. to remove DD-137 board. Open the VC-240/241 board. Refer to 2-9. to remove the two screws (M1.7 × 2.5) with which the MD frame assembly is fixed on the CS frame assembly. Refer to 2-9. to remove the mechanism deck and VC-240/241 board. Remove the CN006 (27P 0.3 mm) of the VC-240/241 board. Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
DC power supply (+4.5Vdc)
: Unloading : Loading Disconnect from CN006 (27P) of VC-240/241 board
CN006
VC
-24
0/2
41
boa
rd
—8—
Loading motor
SELF-DIAGNOSIS FUNCTION 1.
2.
SELF-DIAGNOSIS FUNCTION
Viewfinder or LCD screen
SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the counter of the viewfinder, LCD screen or LCD window consists of an alphabet and 4-digit numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem.
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder, LCD screen or LCD window what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.
LCD window
C : 3 1 : 11
C:31:11
Blinks at 3.2Hz
31
C
Detailed Code
Block
Repaired by:
C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer
3.
11
Refer to page 10. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.
SERVICE MODE DISPLAY
The service mode display shows up to six self-diagnosis codes shown in the past.
3-1.
Display Method
While pressing the “STOP” key, set the switch from OFF to “VCR or PLAYER”, and continue pressing the “STOP” key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes. Viewfinder or LCD screen
LCD window
3 C : 3 1 : 11
[3] C : 3 1 : 1 1
Lights up
[3] Backup No.
C:31:11 Self-diagnosis Codes
Control dial
Order of previous errors
3-2.
Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time
3-3.
End of Display
Turning OFF the power supply will end the service mode display. Note: The “self-diagnosis display” data will be backed up by the coin-type lithium battery of CK-92/94 board BT3201. When this coin-type lithium battery is removed, the “self-diagnosis display” data will be lost by initialization.
—9—
Ver 1.2 2001. 11
4.
SELF-DIAGNOSIS CODE TABLE
Repaired by:
Self-diagnosis Code Block Detailed Function Code
Symptom/State
Correction
C C C C
0 2 2 3
4 1 2 1
0 0 0 1
0 0 0 0
C
3
1
1
1
C C
3 3
1 1
2 2
0 1
C C C C C C
3 3 3 3 3 3
1 1 1 1 1 1
2 2 2 3 4 4
2 3 4 0 0 2
C
3
2
1
0
C
3
2
1
1
C
3
2
2
0
C
3
2
2
1
Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape.
C
3
2
2
2
T reel fault.
C
3
2
2
3
S reel fault.
C
3
2
2
4
T reel fault.
C
3
2
3
0
FG fault when starting capstan.
C
3
2
4
0
FG fault when starting drum
C
3
2
4
2
FG fault during normal drum operations
E
6
1
0
0
Difficult to adjust focus (Cannot initialize focus.)
E
6
1
1
0
Zoom operations fault (Cannot initialize zoom lens.)
E
6
2
0
0
E
6
2
0
1
Steadyshot function does not work well. (With pitch angular velocity sensor output stopped.) Steadyshot function does not work well. (With yaw angular velocity sensor output stopped.)
Use the info LITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Inspect the lens block focus reset sensor (Pin 8,9 of CD-252 board or Pin qk of CN3000 of FP-219 flexible board) when focusing is performed when the control dial is rotated in the focus manual mode, and the focus motor drive circuit (IC201 of VC-240/241 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin ql,w; of CD-252 board or Pin 9 of CN3000 of FP-219 flexible board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC201 of VC-240/241 board) when zooming is not performed. Inspect pitch angular velocity sensor (SE3051 of JK-188 board) peripheral circuits. Inspect yaw angular velocity sensor (SE3052 of JK-188 board) peripheral circuits.
— 10 —
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E SECTION 1 GENERAL
1-1
This section is extracted from instruction manual. (DCR-TRV6E/TRV11E/TRV20E model)
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20
1-21
1-22
1-23
1-24
1-25
1-26
1-27
1-28
1-29
1-30
1-31
1-32
1-33
1-34
1-35
1-36
1-37
1-38
1-39
1-40
1-41
1-42
1-43
1-44
1-45
1-46
1-47
1-48E
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E SECTION 2 DISASSEMBLY The following flow chart shows the disassembly procedure.
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
2-1. LCD section-1 (TRV6/TRV6E model) (PD-124 board, Inverter transformer unit, Indication LCD block assembly) 2-2. LCD section-2 (TRV11/TRV11E/TRV20/TRV20E model) (PD-123/124 board, Inverter transformer unit, Indication LCD block assembly)
PD-123/124 board service position (All model)
2-3. EVF section (LB-64 board)
LB-64 board service position
2-4. Front panel block assembly (MA-385 board), Cabinet (R) block assembly
MA-385, CK-92/94 boards service position
2-6. DD-137 board, EVF block assembly, BT panel section
MA-385, CK-92/94, DD-137 boards service position
2-7. Lens section-1 (Lens device, FP-219 flexible board) (TRV6/TRV6E/TRV11/TRV11E model) 2-8. Lens section-2 (Lens device, CD-252 board) (TRV20/TRV20E model) 2-12. Memory stick connector (TRV11/TRV11E/TRV20/TRV20E)
2-9. VC-240/241 board, Mechanism deck
2-10. Control switch block (FK30150)
2-11. JK-188 board, Control switch block (PS30150)
[Connection diagram for service position (Mainly for voltage measurement and check)] (MA-385, JK-188, CK-92/94, CD-252, FP-219 flexible, VC-240/241, DD-137 boards, Mechanism deck)
2-5. CK-92/94 board, Speaker, Control switch block (CF30150)
2-13. Hinge assembly, LCD harness processing
2-1
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD SECTION-1 (TRV6/TRV6E MODEL) (PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) 1 Two screws (M1.7 × 4), lock ace, p2
4 P cabinet (C) assembly
REMOVING THE PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICAITON LCD BLOCK ASSEMBLY 6 Screw (M1.7 × 2.5)
1 Liquid crystal indicator module (24P)
3 Four claws
5 Two screws (M1.7 × 2.5)
2 Two screws (M1.7 × 4), lock ace, p2
D
2 Back light (Cold cathode fluorescent tube) (15P)
4 Harness (PC-118) (12P) 3 Harness (PC-119) (14P)
qa P B Doa 1 rd 24
8 Inverter transformer unit (5P)
P B Doa 1 r d 24
B
9 PD-124 board A
7 Two tapping screws (M1.7 × 3.5)
5 FP-182 flexible board (21P) qs Release the two claws, and slide the indication LCD block assembly in the direction of the arrow E.
C
qf Indication LCD block assembly
8 P frame (13)
qd LCD holder 9 Back light Cold cathode fluorescent tube
E q;Two claws
0 Liquid crystal indicator module D
qa P frame assembly A
7 Two claws
C
B 6 P cabinet (M)
2-2
2-2. LCD SECTION-2 (TRV11/TRV11E/TRV20/TRV20E MODEL) (PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) 1 Two screws (M1.7 × 4), lock ace, p2
4 P cabinet (C) assembly 3 Four claws
REMOVING THE PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICAITON LCD BLOCK ASSEMBLY
2 Two screws (M1.7 × 4), lock ace, p2
6 Screw (M1.7 × 2.5)
1 Liquid crystal indicator module (24P)
5 Two screws (M1.7 × 2.5)
D
2 Back light (Cold cathode fluorescent tube) (15P)
4 Harness (PC-118) (12P) 3 Harness (PC-119) (14P) 9 PD-123 board (TRV11/TRV11E/ TRV20 model) PD-124 board (TRV20E model)
9 P B Doa rd
8 Inverter transformer unit (5P)
P B Doa rd
B
C
A
5 FP-182 flexible board (21P)
qs Release the two claws, and slide the indication LCD block assembly in the direction of the arrow E.
qf Indication LCD block assembly 8 Back light Cold cathode fluorescent tube
qd LCD holder E
q;Two claws 7 Liquid crystal indicator module D qa P frame assembly C
A 7 Two claws
B 6 P cabinet (M)
[PD-123/124 BOARD SERVICE POSITION (ALL MODEL)] AC IN
DC IN LANC jack
AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
Adjustment remote commander (RM-95)
CN009 1
2
19
20
Liquid crystal indicator module
P B Doa rd
CPC lid Screw (M1.7 × 4), lock ace, p2
Back light Cold cathode fluorescent tube
CPC-8 jig (J-6082-388-A)
Indication LCD block assembly Inverter transformer unit
PD-123 board (TRV11/TRV11E/TRV20 model) PD-124 board (TRV6/TRV6E/TRV20E model)
2-3
2-3. EVF SECTION (LB-64 BOARD) 1 Raise the finder in the direction of the arrow A, and slide it in the direction of the arrow B. A
2 Two tapping screws (M1.7 × 5)
B
3 Two tapping screws (M1.7 × 5)
2 VF cabinet (upper) assembly
1 Press down the finder and release the two claws.
3
4 VF cabinet (lower) assembly
REMOVING THE LB-64 BOARD 9 VF lens assembly 6 LCD (16P) 7 LB-64 board 1 FP-180 flexible board (27P)
8 LCD cushion (1) 5 LCD cushion (2) 4 BL illuminator 3 LCD cushion (2) 2 Three claws
[LB-64 BOARD SERVICE POSITION] VF lens assembly
AC IN
LB-64 board
AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
CPC-8 jig (J-6082-388-A)
Adjustment remote commander (RM-95) CN009 1
2
19
20
CPC lid Screw (M1.7 × 4), lock ace, p2
DC IN LANC jack
2-4
2-4. FRONT PANEL BLOCK ASSEMBLY (MA-385 BOARD), CABINET (R) BLOCK ASSEMBLY 2 Screw (M1.7 × 4), lock ace, p2
1 Slide the finder in the direction of the arrow A.
3 Claw
qd Screw (M1.7 × 4), lock ace, p2 4 Top cabinet assembly
qa Screw (M1.7 × 2.5), lock ace, p2
A qj FP-179 flexible board (51P)
qk Cabinet (R) block assembly qs Screw (M1.7 × 2.5), lock ace, p2
5 Screw (M1.7 × 4), lock ace, p2 8 Screw (M1.7 × 4), lock ace, p2
9 FP-188 flexible qh Screw (M1.7 × 4), lock ace, p2 board (28P) qf Press the eject knob in the direction of the arrow C and open the grip cabinet.
B
B
Eject knob 7 Open the jack cover (DC) and jack cover (S).
C
qg Screw (M1.7 × 4), lock ace, p2
6 Screw (M1.7 × 4), lock ace, p2 0 Front panel block assembly
Grip cabinet
REMOVING THE MICROPHONE UNIT, MA-385, SE-107 BOARD
7 SE-107 board 5 Three tapping screws (M1.7 × 3.5)
6 MA-385 board
1 Three claws 2 Tapping screw (M1.7 × 3.5) 3 Microphone retainer 4 Microphone unit
2-5
[MA-385, CK-92/94 BOARDS SERVICE POSITION]
AC IN
AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
CPC-8 jig (J-6082-388-A) FP-179 flexible board (51P)
DC IN
CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)
Adjustment remote commander (RM-95)
CN009 1
2
19
20
SE-107 board
CK oard B
JK-188 board (28P) Microphone unit
MA-385 board CPC lid Screw (M1.7 × 4), lock ace, p2
Cabinet (R) block assembly
2-5. CK-92/94 BOARD, SPEAKER, CONTROL SWITCH BLOCK (CF30150) qh Two tapping screws (M1.7 × 3.5)
qg Eject knob 5 Control switch block (CF30150) (7P)
4 FP-181 flexible board (6P)
A C
Slant the bottom frame assembly, tripod insulating sheet and tripod table all three parts together, in the direction of the arrow C and remove from the cabinet (R).
qj Control switch block (CF30150)
B CK Bo ar
d
7 Four tapping screws qs Bottom frame (M1.7 × 3.5) assembly A 1 Two tapping qd Tripod insulating sheet screws (M1.7 × 3.5) B
qf Tripod (large)
2 Speaker retainer assembly
2-6
3 Speaker (2P) 8 Two claws
6 Harness (PC-118) (12P) 9 Harness (PC-119) (14P) qa Three screws (M1.7 ), lock ace, p2 with scotch grip.
q; CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)
2-6. DD-137 BOARD, EVF BLOCK ASSEMBLY, BT PANEL SECTION 1 Two screws (M1.7 × 4), lock ace, p2
5 Screw (M1.7 × 2.5) qs Board to board connector (80P)
B
7 EVF block assembly
2 BT panel section
8 CD-252 board (60P) 4 Raise the finder in the direction of the arrow A. A
B
rd
a Bo
-
DD-137
VC
6 Two tapping screws (M1.7 × 5)
qa Screw (M1.7 × 2.5)
3 FP-180 flexible board (27P)
9 Two screws (M1.7 × 2.5)
qd DD-137 board
q; VC heat sink/VC rubber (TRV20/TRV20E model)
[MA-385, CK-92/94, DD-137 BOARDS SERVICE POSITION] FP-180 flexible board (27P)
EVF block assembly
BT panel block assembly
DD-137 board D Bo D-137 ard
DC IN
AC IN
AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
Extension cable (J-6082-395-A) (80P) CD-252 board (60P)
CPC-8 jig (J-6082-388-A) FP-179 flexible board (51P) CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)
d
oar
-B VC
Adjustment remote commander (RM-95) SE-107 board
CK oard B
JK-188 board (28P) MA-385 board
Cabinet (R) block assembly Microphone unit
2-7
2-7. LENS SECTION-1 (LENS DEVICE, FP-219 FLEXIBLE BOARD) (TRV6/TRV6E/TRV11/TRV11E MODEL) 8 Remove the fourteen solderings
4 Two tapping screws (M1.7 × 5)
1 Screw (M1.7 × 2.5)
2 Control switch block (FK30150) (8P)
2 Two tapping screws (M1.7 × 3.5) 7 Seal rubber (W) A
A
9 CCD block assembly
4 Lens block assembly
5 DC-IN connector
qa FP-219 flexible board 0 Tapping screw (M1.7 × 3.5)
5 Lens device (LSV-650B)
6 Optical filter block 3 FP-219 flexible board (24P)
3 Two tapping screws (M1.7 × 3.5)
1 FP-219 flexible board (50P)
2-8. LENS SECTION-2 (LENS DEVICE, CD-252 BOARD) (TRV20/TRV20E MODEL) 3 Two tapping screws (M1.7 × 3.5)
1 Screw (M1.7 × 2.5)
A
2 Control switch block (FK30150) (8P)
5 Remove the three solderings
A 2 NS-10 board 4 Outer connector (hot shoe) 7 lens frame
6 CD shield case
REMOVING THE LENS DEVICE, CD-252 BOARD 4 Lens block assembly
1 NS-10 board (5P)
q; CD sheet 8 Remove the fourteen solderings
5 DC-IN connector
7 Seal rubber (W) 1 CD-252 board (60P) 3 Two tapping screws (M1.7 × 3.5)
6 Optical filter block 5 Lens device (LSV-690A)
2-8
3 Tapping screw (M1.7 × 3.5)
4 Two tapping screws (M1.7 × 5) qa CD-252 board 9 CCD block assembly 2 Flexible board (from Lens block) (27P)
2-9. VC-240/241 BOARD, MECHANISM DECK 2 Control switch block (FK30150) (39P)
1 JK-188 board (60P)
3 Two screws (M1.7 × 2.5) d
ar
Bo
VC
2 Two claws
REMOVING THE VC-240/241 BOARD, MECHANISM DECK 9 Two screws (M1.7 × 2.5), lock ace, p2
4 Mechanism deck, MD frame assembly, Cassette compartment cover
4
q; Cassette compartment cover 4 Flexible board (from drum motor) (10P) 5 Flexible board (from video head) (10P)
qa Mechanism deck
A
B
A
B
C
D
d
ar
Bo
VC
3 FP-102 flexible board (27P) 8 MD frame assembly
1 Two screws (M1.7 × 2.5)
D C
2 Flexible board (from capstan motor) (27P)
3 VC-240 board (TRV20/TRV20E model) VC-241 board (TRV6/TRV6E/ TRV11/TRV11E model)
1 FP-179 flexible board (51P)
7 Four screws (M1.4 × 1.5)
6 VC-240 board (TRV20/TRV20E model) VC-241 board (TRV6/TRV6E/TRV11/TRV11E model)
2-9
d
ar
Bo
VC
2-10.CONTROL SWITCH BLOCK (FK30150) 4 FP-183 flexible B A board (8P) (TRV11/TRV11E/ TRV20/TRV20E model)
5 Control switch block (PS30150) (6P)
8 Remove 9 in the direction of the arrow C while taking care not to be caught by other parts. 6 Four tapping screws (M1.7 × 3.5) 3 Zoom cover 2 Claws
C 1 Screw (M1.7 × 2.5)
B A 9 Control switch block (FK30150) CS frame assembly
7 Two tapping screws (M1.7 × 3.5)
REMOVING THE CONTROL SWITCH BLOCK (FK30150), CS FRAME ASSEMBLY 4 Control switch block (FK30150)
1 Screw (M1.7 × 2.5) 3 CS frame assembly
2 Dowel
2-11.JK-188 BOARD, CONTROL SWITCH BLOCK (PS30150) PRECAUTION DURING INSTALLATION
REMOVING THE JK-188 BOARD 2 Screw (M1.7 × 2.5)
1 Screws (M1.7 × 2.5) 3 Tapping screw (M1.7 × 3.5) 4 Control switch block (PS30150) 4 JK-188 board
3 Jack frame
1 Tapping screw (M1.7 × 3.5)
2 JK-188 board, jack frame
2-10
To attach, align the switch position as shown.
[Connection diagram for service position (Mainly for voltage measurement and check)] (MA-385, JK-188, CK-92/94, CD-252, FP-219 FLEXIBLE, VC-240/241, DD-137 BOARDS, MECHANISM DECK) Control switch block (PS30150) (6P)
FP-180 flexible board (27P)
EVF block assembly
BT panel section
DD-137 board D Bo D-13 ard 7
DC-IN connector
Control switch block (FK30150) (39P)
Mechanism deck
(TRV20/TRV20E model) NS-10 board
Extension cable (J-6082-395-A) (80P)
CD-252 board
AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
VC oard B
Lens block assembly
FP-179 flexible board (51P)
(60P)
(TRV6/TRV6E/TRV11/TRV11E)
AC IN
CPC-8 jig (J-6082-388-A) CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)
Lens block assembly
CK oard B
(60P) FP-219 flexible board (50P)
Adjustment remote commander (RM-95)
VC-240 board (TRV20/TRV20E model) Cabinet (R) block assembly VC-241 board (TRV6/TRV6E/TRV11/TRV11E model) (28P) JK-188 board
SE-107 board MA-385 board Microphone unit
2-12.MEMORY STICK CONNECTOR (TRV11/TRV11E/TRV20/TRV20E) Perform the disassembling after steps 1 – 4 of 2-10 is complete. 5 Open it.
A
3 2 FP-183 flexible board Be careful not to be caught by other parts.
4 Push it in the direction of the arrow A.
7 Remove the MS led assembly in the direction of the arrow B. qd Memory stick connector 1 Screw (M1.7 × 2.5) q;
B
6 Release the two engaged portions. 9 Remove the MS chassis assembly in the direction of the arrow C.
2-11
C
qa Remove the eleven solderings. qs FP-183 flexible board 8 Tapping screw (M1.7 × 3.5)
2-13.HINGE ASSEMBLY, LCD HARNESS PROCESSING Start repair work after removing LCD by performing steps 1 – 6 of 2-1 or 2-2 and remove the CK-92/94 board by performing steps 1 – 0 of 2-5. q; Hinge assembly 8 Screw (M1.7 × 2.5)
2 FP-181 flexible board Be careful not to be caught by other parts.
3 Two claws 4 Hinge cover (rear) 2 Screw (M1.7 × 4), lock ace, p2
5 9 FP-181 flexible board 6 Harness (PC-118) (12P)
3 Harness (PC-119) (14P) Be careful not to be caught by other parts.
1 Two screws (M1.7) with scotch grip
4 Harness (PC-118) (12P) Be careful not to be caught by other parts.
7 Harness (PC-119) (14P) 1 Two screw (M1.7 × 4), lock ace, p2 5 Hinge cover (front)
PRECAUTION DURING INSTALLATION (LCD HARNESS PROCESSING)
Extra length is not required in LCD.
Be careful thet harness must not protrude from upper and lower side.
Create an extra length to allow opening and closing.
PDBoard
CKBoard
Allow extra length of this extent in the cabinet.
2-12
2-14.CIRCUIT BOARDS LOCATION
LB-64 (EVF BACK LIGHT)
CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)
DD-137 (DC/DC CONVERTER)
INVERTER TRANSFORMER UNIT
JK-188 (AV IN/OUT)
PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O
MA-385 (AUDIO I/O)
SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)
2-13
2-15.FLEXIBLE BOARDS LOCATION CONTROL SWITCH BLOCK (FK30150)
CONTROL SWITCH BLOCK (PS30150)
FP-183 (TRV11/TRV11E/TRV20/TRV20E)
FP-181 CONTROL SWITCH BLOCK (CF30150)
FP-182 FP-228
FP-180
FP-100
FP-179
(From LENS BLOCK) (TRV20/TRV20E model) FP-219 (TRV6/TRV6E/TRV11/TRV11E) (CCD IMAGER)
FP-102 From TOP/END SENSOR, TAPE LED (From VIDEO HEAD)
(From DRUM MOTOR) (From CAPSTAN MOTOR)
(From LENS BLOCK) (TRV6/TRV6E/TRV11/TRV11E model)
2-14E
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
SECTION 3 BLOCK DIAGRAMS ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
3-1. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV6/TRV6E) FP-219
VC-241 BOARD(1/3)
(FLEXIBLE)(1/2)
LENS ASSY
J3004 DV IN/OUT
(4-13)
IRIS (SHUTTER)
(4-25)
138 139
IC3000
CCD OUT
8
CCD IMAGER
(4-31)
IC701
CN701
CN3001 17 17
2
30
| (GCAM3) S/H,AGC A/D CONV.
AD0-AD9
|
47
AD SO AD SCK
23
16 CLP OB
CLPDM,PBLK XSHP,XSHD
V DRAIN 6
112
205
203 Y0-Y7
Y0-Y7 207
211
213
215
59
1 C0-C3
3
C0-C3 5
7
56 17 HD,VD,OE
HD,VD OE
71
21
72
23
145
(CAIN)
18
IC702
21
V1-V4,VSHT H1,H2,RG
5
5
9
9
22
TIMING GENERATOR
30
15
42
33
12
CL
HD,VD
44
13 15
132
1
SPCK
M
IRIS HALL +,-
5
37
AFCK(IC903)
196
20 • 19
IC302
I HALL AD
HD VD
184 • 183
(4-29)
IRIS HALL AMP
IC801
50
18 • 17 • 16 • 14
CHARACTER GENERATOR
4
1
COL0 195 • | COL3 194 • 191 • 190
159 VSP SO,SI,SCK
3
75 73 71 105 • 106
31 31
18
67
(4-28)
65
FC A,B FC XA,XB
139 35 35
14
2
4
FOCUS MOTOR DRIVE
21 23
38 38
63
ENO,DIR OA,DIR OB
9
ZOOM MOTOR DRIVE
17 19
28 28
24
7
PANEL R PANEL B
JK-188 BOARD (2/3)
HD,VD EVF G
(4-61)
EVF R EVF B 10 • 11
13
55 59
ENI,DIR 1A,DIR 1B
Y
46
C
7
IC1301
18 14
143 16
22
(TAKO) 144
ZOOM MOTOR
FC RST
137 SPCK (IC751)
ZM RST
ZOOM RESET SENSOR
9
31 • 68
138
39 39
AFCK
2 6
Y C
34
G
S VIDEO
51 47 IR V
IC1001
42
IR L
62
IR R
63
54
L
L
15 VSP SO,SCK
14
30 30
AUDIO I/O
V 55
J3003
49 40
(XYZ)
34 (ALIGN)
20
J3001 G
V
(4-64)
(4-50)
Y
C 31 46
48
36
C
35 50 C
39
(4-48)
IC903
Y
V
24
LINE OUT LINE IN AGC ACC
IC204
CN3001 Y
CN001
12 142
5
25 25
PANEL G
140 141
ZM A,B ZM XA,XB
FRRV,TRRV,TRRT
161
OSD CS OSD SO OSD SCK
M
(SEE PAGE 3-7)
MC BUS 179
52
IRIS DRIVE
2
21
ATF ERR
79
170
44 44
11
TO OVERALL BLOCK DIAGRAM (2/3)
PB CK
48
8 IRIS PWM
EEPROM
M
6
88 81
SPCK(IC751)
38
AD DT 6
182
3
FOCUS MOTOR
REC DT
83
110
IR FSC
42 42
4
FOCUS RESET SENSOR
REC CK
97
111
IC202 IC203
49 49 48 48
6
SFD BCK
(4-36)
IRIS DRIVE +,-
2
H
DATA TO SFD DATA FROM SFD
46
35
(4-25)
37
FRRV,TRRV,TRRT
127
4
(4-27)
CN3000 IRIS METER
MC BUS
49
99
45 X701 36MHz
47
LCK
153
133
11 11 13 13
51 141
11
C4-C7 2
16
42 42
29
156
1
25
9 (LIP) DV INTERFACE
TRCK
152
115 9
1
IC361
CN3001 39 39
DV SIGNAL PROCESS
AD CLK
1
TPA+,TPB+,-
6
42
(4-33)
IC301
CN001
(4-36) 45
L BUS
68
|
X301 24.576MHz
142
201
61
70
V DRAIN 6
199 |
(BIRDS+) CAMERA PROCESS, FOCUS/ZOOM CONTROL, EVR
48 19
IC751
121
11
6
1-4 • 10-13
131
AUDIO/VIDEO
R
R 50 36
59 NIGHT SHOT
CN3001
CN701
A/D CONV. Y0-Y7 43
14
52
JK-188 BOARD(1/3)
8
PITCH SENSOR
66
18
58 58
SFD BCK 47
2
57 57
9 8 12
IC1002 (ADC&DAC) D/A CONV. A/D CONV.
38 HD,VD,OE 37 34
15 16
19 64 17 2
3 2
L R
58
PITCH AD
62
AD SO,AD SCK
23
EXCEPT AEP/UK MODEL 46
ZOOM AD
49
HI SO,SI SCK | 50
CN2051 11
11 11
10
10 10 HI SO,SI,SCK
TO OVERALL BLOCK DIAGRAM (3/3) CN2001
MIC L
1
35
(SEE PAGE 3-10)
IC2002 22
MIC R
3
1
J2001
R
MIC
L
MIC AMP
14
SHOE MIC L SP+,ZOOM AD OSD CS,SO,SCK PANEL R,G,B,EVF R,G,B,HD,VD IR V,IR L,IR R
L 3
3
3
1
1
1
5
5
5
LANC SIG
R
36
3
48
33
(4-105) J2002 LANC SIG
LANC
26
26 26
CN2701
16
MA-385 BOARD(1/2)
3-1
3-2
J3002 L
45 41
25
48
59
SE-94 BOARD
2
R 46 37
SP+,-
63-66 54
1
L R
10
35
YAW AD
MANUAL FOCUS SENSOR
R
53
L R
8
CAM SO,SI,SCK 36
53
YAW/PITCH SENSOR AMP
|
I HALL AD
33
41
CN001
CN3001
12
SE3051
DATA TO SFD
CAMERA CONTROL 40
X801 20MHz
IC3051
YAW SENSOR
IC802
23
(4-89)
SE3052
DATA FROM SFD 49 C0-C7
L
51
IRIS PWM
(4-29) 22
MF A,B
(4-64)
|
L R
HEADPHONE
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
3-2. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV11/TRV11E) FP-219
VC-241 BOARD(1/3)
(FLEXIBLE)(1/2)
LENS ASSY
J3004 DV IN/OUT
(4-13)
IRIS (SHUTTER)
(4-25)
138
X301 24.576MHz
139
IC3000
CN3001
CCD OUT
8
CCD IMAGER
17 17
131
2
30
AD0-AD9
| (GCAM3) S/H,AGC A/D CONV.
47
IC751
|
|
AD SO AD SCK
48 19
CLP OB CLPDM,PBLK XSHP,XSHD
V DRAIN 6
V DRAIN
6
Y0-Y7
|
|
C0-C3
C0-C7
|
|
56
2
29
70
14
28
18 1
IC702
71
13
27
72
12
26
5
5
9
9
22
TIMING GENERATOR
215
7
5
51
| 30
15
42
25
16
33
12
SPCK
10
21
152
23
153
200
202
156
204
206
133
208
212
132
214
216
127
Y0-Y7
49 |
C0-C3
2
4
6
8
13 13
CL
46
MC BUS
49
37
FRRV,TRRV,TRRT
DATA TO SFD DATA FROM SFD SFD BCK
REC CK
99
46
11 11
42 42
29
47
LCK
141
(CAIN)
51 2
9
DV INTERFACE
TRCK
DV SIGNAL PROCESS
17
58
IC361
REC DT
97
45
CN3001 39 39
(LIP)
IC301
3
1 C0-C3
TPA+,TPB+,-
6
42
145
(4-33)
HD,VD OE
1
21
V1-V4,VSHT H1,H2,RG
211
213
115
AD CLK
1
207
32
HD,VD,OE
112
205
203 Y0-Y7
34
(SHIORI) DIGITAL STILL PROCESS
9
L BUS
41
| 17
59
16
23
Y0-Y7
61
(BIRDS+) CAMERA PROCESS, FOCUS/ZOOM CONTROL, EVR
CN001
(4-36) 45
142
201
199
IC1406
24
68
121
11
6
1-4 • 10-13
(4-46)
(4-31)
IC701
CN701
18 HD,VD,OE
44 44
HD,VD
22
110 43
6
4
35
IR FSC
182
5
37
AFCK(IC903)
196
38
SPCK(IC751)
48
(4-25)
AD DT
24
111
45 X701 36MHz
83
6 TO OVERALL BLOCK DIAGRAM (2/3)
88 PB CK
81
ATF ERR
79
(SEE PAGE 3-7)
CN3000 IRIS METER
1
M
IRIS DRIVE +,-
2
8
IC202 IC203
49 49 48 48
IC801
42 42 IRIS HALL AMP
4
3 EEPROM
(4-36)
2
(4-27) 19
1 13
SHUTTER ON
FOCUS MOTOR
M
21
FRRV,TRRV,TRRT
159 VSP SO,SI,SCK 161
3
PANEL G
75
133
PANEL R PANEL B
71 105 • 106
SHUTTER DRIVE
5
11
COL0 195 | • COL3 194 • 191 • 190
31 31
18
M
MC BUS 179
OSD CS OSD SO OSD SCK
15 7
184 • 183
73
IC201
17
FOCUS RESET SENSOR
18 • 17 • 16 • 14
CHARACTER GENERATOR
4
44 44
(4-27)
HD VD
52 50
IRIS HALL +,-
6
20 • 19
IC302
I HALL AD
(4-29)
IRIS DRIVE
H
170
IRIS PWM
EVF G
139 35 35
14
2
4
38 38
21 23
25 25
5
FOCUS MOTOR DRIVE
15
ENO,DIR OA,DIR OB
9
140
AFCK (IC1903)
28 28
24
13
ZOOM MOTOR DRIVE
17 19
(4-50) 10 • 11
CN001
12 Y
55 115
142 7
EVF B
63
141 ZM A,B ZM XA,XB
(4-61)
EVF R
65
FC A,B FC XA,XB
JK-188 BOARD (2/3)
HD,VD
67
IC1301
46
C
59
ENI,DIR 1A,DIR 1B
7
143 144
IC204 ZOOM MOTOR
FC RST
137
ZM RST
96
138
39 39
9
VSP SO,SCK
112
(4-28) ZOOM RESET SENSOR
LINE OUT LINE IN AGC ACC
113
74
85
103
80
72
60
94
Y
2
IC903
C
6
34
42
IR V
IC1001 15
VSP SO,SCK A0-A11
CN701 14
22
JK-188 BOARD(1/3)
43
CN3001
12
SE3051 8
PITCH SENSOR
DATA FROM SFD 31
1
13 • 38
48
49 DATA TO SFD C0-C7
66
I HALL AD
| SFD BCK
IC752
47
18
58 58
2
57 57
35
62
58
PITCH AD
IC1002 (ADC&DAC) D/A CONV. A/D CONV.
15 16
L
J3003
49 40 V
55
AUDIO/VIDEO
R 50 36
19 64 17 2
3 2
L
R
R
L
R J3002
46 37 L
R 45 41
HEADPHONE
25 23 8
SP+,-
10
(4-48)
(4-32)
L
53
L R
37
63-66
AD SO,AD SCK
EXCEPT AEP/UK MODEL
54 YAW AD
12
HD,VD,OE
16Mbit SDRAM
CAM SO,SI,SCK
36
53
YAW/PITCH SENSOR AMP
9 8
38 34
L
R
51
52 18
33
41
CN001
(4-64)
|
CAMERA CONTROL 40
X801 20MHz
IC3051
YAW SENSOR
IC802
23
(4-89)
SE3052
14
AUDIO I/O
IRIS PWM
(4-29) MF A,B
IR R
63
A/D CONV.
D1-D10 Y0-Y7
IR L
62
54
(ALIGN)
59 CN3001
S VIDEO
G
51 47
30 30
20 NIGHT SHOT
J3001 G
V
(4-64) 48
Y
C
24
36
C
35 50 31 46
(XYZ)
34
AFCK
Y C V
39
31 • 68
SPCK (IC751)
14 22
(TAKO)
16
18
CN3001 Y
4 46
ZOOM AD
49
L R
48
59
KASYA ON
HI SO,SI SCK |
SE-94 BOARD
50
(4-45)
(4-45)
171 • 172 • 178
CN2051 MANUAL FOCUS SENSOR
1
11
11 11
2
10
10 10
IC1405 HI SO,SI,SCK
IC1407
16Mbit SDRAM
(4-44)
IC1404
4Mbit FLASH
160 TO OVERALL BLOCK DIAGRAM (3/3) CN2001
MIC L
1
35
(SEE PAGE 3-10)
IC2002 22
MIC R
3
1
MIC AMP
14
L
SHOE MIC L 19 SP+,-
2
12
1
8
39
49
16
24
32
29
(KATHMANDU) DIGITAL STILL CONTROL
45
ZOOM AD
3
A1-A19
PANEL R,G,B,EVF R,G,B,HD,VD
R
MIC
L
1
5
5
5
RXD TXD
(4-105)
232C ON
J2002
IC1403
Q1111 LANC SIG/232C RD
LANC/ DIGITAL I/O
26 LANC GND/232C TD 24
14
23 23
RS232C I/F
181 175
9
12
26 26
7
RXD
5
24
4
23
2
(SEE PAGE 4-91)
TXD
CN2701
MA-385 BOARD(1/2) 16
3-3
CN062 26
CONTROL SWITCH BLOCK (FK-30150) (1/2)
| 35
(4-39)
48
33
MS DIO,MS SCLK,MS BS
53
36
3
193 192
D0-D15
J2001
194
LANC SIG 1
CN008
| 79
3
1
X1401 25.8048MHz
57
OSD CS,SO,SCK
IR V,IR L,IR R 3
R
161
3-4
MEMORY STICK
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
3-3. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV20/TRV20E) CD-252 BOARD(1/2)
VC-240 BOARD(1/3)
IC751
(4-23)
LENS ASSY
J3004
(CARILLON)
DV IN/OUT
138
(4-11)
IRIS (SHUTTER)
(4-11)
13
(4-17)
9
PLL
IC101
IC104
CCD OUT 8
CCD IMAGER
5
11
CDS, AGC
4
2
2
36
4
4
32
SPCK
199
201
203
205
207
211
213
215
142
16
1,13,14
|
|
145
Y0-Y7
65
1 |
IC301
3
C0-C3 5
7
(CAIN)
248
16,17,22
HD,VD OE 60
34
26 26
61
35
25 25
62
15 15
57
23
256
(4-11)
IC102
MCK
25
RC PROCESS
200
202
156
204
206
133
208
212
132
214
216
127
33 Y0-Y7
| 25
29
TIMING GENERATOR
30
(TRV20) 54MHZ(TRV20E)
(4-17)
IC702
18 18
DRAM 18 |
A0-A11
2
16Mbit SDRAM
22 22 CN101
C0-C3
|
109
20
|
16
122
H
ND FILTER METER
17
43 43
IRIS HALL +,-
IC202 IC203 IRIS DRIVE
I HALL AD
25
M
27
DQ0-DQ15
182
89
AFCK(IC903)
196
|
SPCK(IC751)
48
26
19
60 60
20 • 19
18 • 17 • 16 • 14
CHARACTER GENERATOR
42 43 45
1
HD VD
184 • 183
8
F MR A,B
9
FOCUS MOTOR
M
3
M
2
FOCUS +,-
4
ZOON +,-
1
39 39
7
40 40
17
ND FILTER PRE DRIVE
13
36 36
23
35 35
2
34 34
21
SHUTTER DRIVE
PWMO EN0
10
VSP SO,SI,SCK 161
12
(4-22)
32
105 • 106
MR
21
Z MR A,B
19
IC803
Y0-Y7
1
28
46
27
213 233
EVR
|
12 15
EVF G (4-61)
EVF R
65
EVF B
63
10 • 11 Y
55
46
C
59
7
(TAKO)
49
LINE OUT LINE IN AGC ACC
47 38
2
236
37
6
234
36
Y C
48
26
IC801
IR V
IC1001
2 CN101
(4-64)
CN701 37 14
43
(4-21) MF A,B
22
JK-188 BOARD(1/3)
46
IC802
23
65 66
IRIS PWM
IC3051
SE3052 12
YAW SENSOR SE3051
8
PITCH SENSOR
165
SFD BCK |
|
IC1404 CAM SO,SI,SCK
A0-A13
58 58
2
57 57
JID0-JID7
|
AD SO,AD SCK
193 13 • 42
58
62
ZOOM AD
D0-D15
X1401 6,875MHz
|
|
77
212
145
79
|
83
SYSCLK
(4-40) 27 34
CN2051
IC1407
JID0-JID7 11
11 11
2
10
10 10
41
JPEG
18 TO OVERALL BLOCK DIAGRAM (3/3)
(4-105)
CN2001 1
35
22
MIC R
3
1
J2001
R
MIC
L
(SEE PAGE 3-10)
IC2002 MIC AMP
3 33
14
L
19
2
21
4
3
HEADPHONE
SP+,-
4 46
6 49
(4-39)
DI,CI
109
DIGITAL STILL CONTROL
1
L R
50
IC1408
TXD RXD
4
SHUTTER SOUND
2
112
IC1412
(4-40)
16Mbit DRAM FAST PAGE
2,9-16 58-64
5-15
51
1-13 38-48
20-31
62-75
28
(4-40)
SHOE MIC L SP+,-
36 A0-A10
ZOOM AD
|
10
15
26
5
|
|
24
4
17
23
2
1
1
1 • 48
5
5
5
26
26 26
12
24
23 23
14
D0-D15
36
(4-39)
48
IC1410
232C ON
40 SCK
13
XTAL OSC 9
RS232C I/F
MEMORY STICK I/F
|
X1402 20MHz 2 4
IC1403
Q1111
7
TXD
CONTROL SWITCH BLOCK (FK-30150) (1/2) (4-69)
RXD
(4-42)
CN2701
MA-385 BOARD(1/2)
3-5
CN062
CN008
38
PANEL R,G,B,EVF R,G,B,HD,VD
1
LANC GND/232C TD
(4-42)
IC1409
OSD CS,SO,SCK
LANC SIG
LANC SIG/232C RD
16
J3002 L
45 41
23
EEPROM
3
R
J2002 LANC/ DIGITAL I/O
R 46 37
R
25
SPCK1(IC751)
IC1406
IR V,IR L,IR R 3
R
2
L
SYSCLK(IC1412) HI SO,SI,SCK
MIC L
L
3
R
IC1411
50
1
64 17
8
|
SE-94 BOARD
50 36 L
10
53
MANUAL FOCUS SENSOR
19
R
J3003 AUDIO/VIDEO
R
54-52
48
59
55
R
53
L
(4-40)
154
L 49 40 V
2
D/A CONV. A/D CONV.
A0-A10
2
54
PITCH AD
16
(ADC&DAC)
HI SO,SI SCK
181
|
YAW AD
12
|
155
18
8
130 35
64Mbit SDRAM
35 53
YAW/PITCH SENSOR AMP
20
15
IC1002
9
161 34
41
CN001
138
(4-41)
I HALL AD
33
40
X801 20MHz CN3001
DATA FROM SFD SYSCLK(IC1412) DATA TO SFD
CAMERA CONTROL
(4-89)
36 143
ND HALL AD
L
51
VSP SO,SCK
(4-21)
ND PWM
AUDIO I/O
14
EEPROM
38 38 CN151
IR R
63
54
3 5
IR L
62
(XYZ) 15
63-66
NIGHT SHOT
S VIDEO
G
51 47
42
(4-50)
J3001 G
V
(4-64) 39
Y
C 31 46
V
24
34
C
Y 35 50
C
14
36
CN3001
Y
18
22
52
HD,VD,OE
4
CN001
IC1301
|
C0-C7
237
52 52
IC903
JK-188 BOARD (2/3)
HD,VD
67
|
224
50 50
(4-48)
A/D CONV.
17
(4-19)
PANEL B
71
59
222 |
16
PANEL R
73
(ALIGN)
SPCK1(IC751)
FOCUS/ ZOOM MOTOR CONTROL
31
PANEL G
75
34
223 23
34 PWM1 EN1
11
31 • 68
(4-19)
IC204
33
IC201 ZOOM MOTOR
SPCK (IC751)
14
ZOOM MOTOR DRIVE
4
33 33
15
FRRV,TRRV,TRRT
159
COL0 195 | • COL3 194 • 191 • 190
OSD CS OSD SO OSD SCK
SHUTTER ON
9
(SEE PAGE 3-7) MC BUS
3
IRIS COM
15
FOCUS MOTOR DRIVE
TO OVERALL BLOCK DIAGRAM (2/3)
ATF ERR
179
AFCK
MR
6
PB CK
170
ND PWM ND FILTER DRIVE
AD DT
88
79
ND HALL AMP 5
REC DT
83
8
ND HALL AD
59 59
REC CK
81
(4-36)
IC205
55 55 ND DRIVE +,-
SFD BCK
99
6
(4-19)
57 57
23
8
IR FSC
48
IRIS HALL AMP
H
DATA TO SFD DATA FROM SFD
24
18 1
IC302
48 48 ND HALL +,-
4
6
22
17
| IRIS PWM
47 47
16
FRRV,TRRV,TRRT
107
(4-19)
13
37
97
CN701 13 • 38
M
MC BUS
49
18
|
44 44
2
CAM SO,SI,SCK
20 20
47
IRIS DRIVE +,-
47
LCK
HD,VD,OE 31
12
42 42
29
24 X101 66MHz
1
IRIS METER
51 141
153
HD,VD,FLD CAMERA SIGNAL PROCESS
9 (LIP) DV INTERFACE
TRCK
152
21
| 23 23
33
CN3001 39 39
DV SIGNAL PROCESS
17
253
AD SO,SCK
42
(4-33)
251
47 48
TPA+,TPB+,-
6
IC361
L BUS
|
AD0-AD9
11
CLPDM, XSHP,XSHD
V1-V4 RG,H1,H2 40-42,44,45, 9,12,13
45
247 A/D CONVERTER
CN001
(4-36)
78
2
238 1-4,10-12,14
X301 24.576MHz
139
10
IC701
CCD OUT(+) CCD OUT(-)
SPCK1
3-6
MEMORY STICK
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
3-4. OVERALL BLOCK DIAGRAM (2/3)
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. CN009 FOR ADJUSTMENTS 17 SWP
VC-240/241 BOARD(2/3)
(SEE PAGE 4-55) (4-38)
RF MON
REC CK
REC CK
REC DT
REC DT
40
IC102
42
(TRW)
(4-37) 42 AD DT
AD DT
6
6
PB CK
PB CK
ATF ERR
ODD
7
REC/PB AMP
5 6 DRUM
2
27
EVEN
1
8 9
(TRF) EQ A/D CONV. PLL
13
22 24
34
(SEE PAGE 3-2,3-4, 3-6)
PB Y OUT
CN101 6
IC101
15 20
TO OVERALL BLOCK DIAGRAM (1/3)
(4-52)
J MECHA DECK
20
31
SWP
95 60
SWP
78 |
(4-59)
MC BUS FRRV TRRT,TRRV
IC501
VSP SO,SI,SCK
MECHA CONTROL
(4-60)
2-4
M902 CN007
115 45
32
CAP FG
CN002 69
CAP PWM
56
IC401
| (RABI) 108
(4-107)
CN1603
54
CN1603
68 68
18
(2/2)
IC1601
SWITCHING 66 66
61
PWM DRIVE DRUM PWM
52
53
CAP VS
62 62
18.22
(SEE PAGE 3-10)
HI SO,SI,SCK
CAPSTAN MOTOR
11
(4-56)
| 14
58 58
DRUM VS
SWITCHING 58
60 60
(RABI) DRUM MOTOR DRIVE
11
LPF
TO OVERALL BLOCK DIAGRAM (3/3)
M
1 | 4
(4-55)
IC401
Q1611
DRUM ERROR 22
1
21,23,19
(2/2)
|
X501 20MHz
FG
17 | 20
CAPSTAN MOTOR DRIVE
CN002 64 64
CAP ERROR
LPF
68
25
Q1610
74
76
CAPSTAN
IC402
(4-55)
37 106
CAPSTAN FG AMP
2,3
| FRRV TRRT TRRV
14,15
CAP ON,CAP FWD
46
26
IC502 EEPROM
DRP SO,XDRP SCK
80
DD-137 BOARD(1/3)
CN005
M901 5
20,21,24
2
DRUM MOTOR
M
| 10
(1/2)
2
DRUM FG
1
DRUM PG
47 DRUM ON,DRUM FWD,DRUM START
83
48
82
63
16,6,3
81 116
DRUM FG
1
DRUM PG
59
DRUM FG AMP
64
CHIME SDA,CHIME SCK,CHIME VDD XCC DOWN
117
61 DRUM PG AMP
CN006 1
49
LOAD,UNLOAD
26,25
50
114 113
54
53
96
LOADING MOTOR DRIVE
28,30
|
M
M903 LOADING MOTOR
4 TREEL FG
40
SREEL FG
48
TAPE END
34
42,43 REEL FG AMP
45,46
5
35 TAPE END DETECT
TAPE TOP
36
37 TAPE TOP DETECT
DEW SENSOR
20
T REEL
21
SENSOR
24
S REEL
23
SENSOR Q902
DEW DET
TAPE END SENSOR 25
55
TAPE LED ON Q901 TAPE TOP SENSOR
44
39
27
REC PROOF SW
D901 TAPE LED
MODE SW A - MODE SW D
| 42
12
REC PROOF 15
S901
7 |
4PIN CONNECTOR
CN901
9 XCC DOWN 11
S903 C IN
16 MODE |
Note : VC-240 BOARD : DCR-TRV20/TRV20E VC-241 BOARD : DCR-TRV6/TRV6E/TRV11/TRV11E
S902
16
3-7
SWITCH
18
3-8
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
3-5. OVERALL BLOCK DIAGRAM (3/3)
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. Note : VC-240 BOARD : DCR-TRV20/TRV20E VC-241 BOARD : DCR-TRV6/TRV6E/TRV11/TRV11E
9
FP-181
CK-92/94 BOARD(1/2)
(FLEXIBLE)
PANEL REVERSE SW
3
4
4
CAMERA FUNCTION SW MEMORY FUNCTION SW PANEL CLOSE SW MENU SW DISPLAY SW DATA CODE SW
AD4X
CN3204
7
CK-94 BOARD (2/2)
(4-62)
IC1104
CN003 3
11 10
VC-240/241 BOARD(3/3)
S3201-3216 CN96
S97
PD-123 BOARD(REF.NO.2000 SERIES): TRV11/TRV11E/TRV20 PD-124 BOARD(REF.NO.3000 SERIES): TRV6/TRV6E/TRV20E
CN009 FOR ADJUSTMENTS
13 39
97
KEY AD4
99
KEY AD6
15 37
HI CONTROL
17 35
CN3205 XCS OSD
44
OSD SO XOSD SCK
45
1 2
PD-123/124 BOARD
51
OSD SO,SCK
1
50
8
1
2
46
IC2171 IC3171
CN3171 CN2176
CN3201
(4-93/4-97)
LCD DRIVE
7
2
11
1
30
20
9
9
12
12
LCD INDICATOR
CN2175 CN3173
PANEL VG 13 39
COM1-4 SEG1-16
PSIG 27 25 PANEL COM
CONTROL SWITCH BLOCK(CF-30150)
15 37 CHIME SDA CHIME SCL
S103-106 LCD BRIGHT SW VOLUME SW
6
5
100
19 33
6
96
11 41
5
CHIME AD0
71
CHIME AD2
73
KEY AD7
KEY AD3
XCC DOWN
4
4
3
3
1
51
67
DIAL A
3
49
68
DIAL B
CN3203
CN100
S3218 21 31
(SEE PAGE 4-83)
RESET
38
5
(4-96/4-99)
8
48
9
43
7
7
47
7
45
6
6
46
CHIME SDA CHIME SCK CHIME VDD
40
XCC DOWN
18
HI SO
33
HI SI
34
XHI SCK
35
TO OVERALL BLOCK DIAGRAM(2/3)
(SEE PAGE 3-7)
BATT LI 3V
3
CN3205
7
IC1102
21 31
9
9
22 30
10
10
45 42
(4-61)
51
6
LANC IN
1
10
LANC OUT
2
12
VDD 77
IC1103
VDD SWITCH
HD 17 35
1
1
1
2
2
48
LANC SIG
CN2173 CN3172
11
LANC I/O
(4-61)
CONTROL SWITCH BLOCK(FK-30150) (2/2)
CN008
X1101 20MHz
40
X1102 32.768KHz
52
IB SI
48
53
IB SO
49
41
Q1104
S1
2
1
1
XCAM STBY SW
POWER SW
4
3
3
XVTR MODE SW
BATT/EXT SW
66
1
5
5
XPHOTO STBY SW
FAST CHARGE
50
S2 START/STOP SW
5 CN064
4
16
XS/S SW
21
17
XEJECT SW
S61
(SEE PAGE 4-91)
EJECT SW
VTR DD ON
29
CAM DD ON
28
SHOE ON
81
VTR FUNCTION SW LASER LINK SW
14
94
KEY AD1
18
93
KEY AD0
36
SIRCS ENV
59
46
6
48
4
SP+,-
KEY AD2 19
10
XPHOTO FREEZE SW SIRCS SIG
47
4
9 PWM
PANEL 4.6V Q2172,2173 Q3171,3172
P UNREG
DD-137 BOARD (3/3)
LB-64 BOARD 3
6
25
3
4
26
2
8
8
24
4
2
2
27
1
10 10
23
5
5
14
14
14
R,G,B 2 4 COM
12
1
14 14 CN2202
95
45
HI SO,SCK
4
16 16
(4-54)
24
IC1803
18 18
1
(4-86)
20 20 14
42 TIMING GENERATOR
48 9
1
1
3
3
5
5
7
7
IC2201 EVF BL 4.6V
Q2201 INVERTER PWM
17 17 36
3
25
8
20
7
21
ND2201 BACK LIGHT
BACK LIGHT DRIVE
EVF BL + 24 24
37
R1693,1694
SHOE UNREG 38
EVF BL -
EVF BL 4.6V
22 22 CN1603 CN2201
CN1604 BATT SIG EVF BL+
73 73 BATT/EXT SW
2 75 75
EVF BL-
71 71
EVF VG
76 76
EVF VCO
FAST CHARGE
3
BATT UNREG J1602 BATTERY TERMINAL
4
CN009 FOR ADJUSTMENTS
5 TRV20/TRV20E
70 70
S
VTR UNREG
2
VTR UNREG
72 72 3
74 74
Q1602
65 65 67 67
1 DC IN
(4-107)
IC1601 IC1602
2 3
DC/DC CONVERTER
CN701
A 3.1V
P UNREG 80 80
D 1.5V
CN152
OSD,CS,SO,SCK
A 2.8V
MA-385 BOARD(2/2)
SHOE ON 27 27
AU 2.8V
HI,SO,SI,SCK TO OVERALL BLOCK DIAGRAM(1/3)
Q1626 30 30
CAM -7.5V
ZOOM AD SHOE UNREG
32 32
CAM 15V CN1603
SHOE MIC L CN002
LANC SIG
PANEL -15.3V
28
30 30
S2061 FOCUS SW
JK-188 BOARD (3/3)
(SEE PAGE 3-1,3-3,3-5)
IR V,IR L,IR R
PANEL 4.6V 15 15
PANEL/EVF 2.8V
1
15
REMOTE COMMANDER RECEIVER
TRV6/TRV6E/TRV11/TRV11E
FP-219
EVF 13.3V RP 4.6V
(FLEXIBLE)(2/2)
IR V IR L
A 4.6V
IR R S3000
AU 4.6V
SIRCS PWM SUPER NIGHT SHOT SW
EVF BL 4.6V
3-9
41 46 48
IC1901 IR TRANSMITTER
18
IR DRV EM
22 7
IR FSC
( IC301
S2071-2074
196 )
50 50 CN3001
16
18 18 CN701
(4-105)
IC2091
SIRCS SIG
PANEL 13.3V
DD-137 BOARD (2/3)
SUPER NIGHT SHOT SW
3 CN101
PANEL R,G,B EVF R,G,B HD,VD,SP+,SP-
78 78
D 1.9V
MT 4.9V
S001
31 31
D 3.1V
D 2.8V
NS-10 BOARD
CD-252 BOARD (2/2)
VTR DD ON CAM DD ON
CN1601
BACK LIGHT DRIVE
5
4
LANC SIG
CN1602
2
6
31
1
INVERTER BLOCK
22
MOD
1
(SEE PAGE 4-91)
1
20
24
RGB DRIVE
SHOE MIC L
8
CN3101
CN3174 CN2174
12 12
VD
7
18 22
24
39
HD
INTELLIGENT ACCESSORY SHOE
12
CN2101
2
SP901 SPEAKER
CN002
IC1802
46
8
2
1
(4-54) 48 EVF R,G,B
RV51 ZOOM VR
2 7 8 10 12 13 12 19
BL ON
2
46
PHOTO SW
6
CN003
BATT SIG
PHOTO REC S71
LCD UNIT
I/F
Q1102,1105 SIRCS CARRIER
3
PSIG
HD OUT
40
S62-70,72
5
21 11
TIMING GENERATOR
CN3206
87
CONTROL SWITCH BLOCK(PS-30150)
27
IC2105 IC3102
46
42
4
20
VCOM
(4-96/4-99)
VD 50
24
CN3202
16 36 2
19 VR,VG,VB
22
5
HI SO,SCK
XRESET
20
RGB DRIVE
39
RESET BT3201 LITHIUM BATTERY
IC2104 IC3101
PANEL R,G,B
HI SO,SI,SCK
DIAL
11
8
6
S102
CONTROL
10
11
11 41
5
S100,101 PROGRAM AE SW EXPOSURE SW
10
26 26
XHD OUT
CK-92 BOARD : TRV11/TRV11E/TRV20 CK-94 BOARD : TRV6/TRV6E/TRV20E
(4-52)
CN001
18 CN3001
3-10
LED DRIVE CN2071
D2701,2072
LCD UNIT
ND901 BACK LIGHT
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
3-6. POWER BLOCK DIAGRAM (1/2) PD-124 BOARD
*1 : DCR-TRV6/TRV6E/TRV11/TRV11E *2 : DCR-TRV20/TRV20E
DD-137 BOARD
IC3101
BATT SIG 73
Q1625, 1626
J901 BATTERY TERMINAL
RGB DRIVE
SHOE ON 27
SHOE UNREG
(4-61)
INIT CHARGE ON 69 VTR DD ON 65 CAM DD ON
(4-99)
67
CN1602
CN3171
1
FAST CHARGE
F1601
BATT UNREG
71 BATT/XEXT SW
PANEL 4.6V
75
8
Q3103
7
Q1601, 1602
F1602
Q1603, 1604
3
L3101
PANEL 13.3V 6
BATT SIG
2
P UNREG
76 Q1615-1617,1624
12 POFF
IC3171
70 VTR UNREG 72
F1603
ACV UNREG
1
TIMING GENERATOR
74 30
SHOE UNREG
2 BATT/XEXT
4
(4-99)
MT 4.75V 55 57
32
3 CN1601
BLON
LCD INDICATOR DRIVE
2
INVERTER BLOCK
5
BACK LIGHT DRIVE
Q3171,3172
CN3174
INIT CHARGE ON
(4-97)
LF1601
SHOE ON
CN3172
53
MT 4.9V
F1604
J902 DC IN
IC3102
EVER 3.0V 5
4.9V REG
F1605
CN3101
14
BATT UNREG
BATT UNREG
F1606
CHARGE SWITCH
18
BATT FET ON
TO POWER BLOCK DIAGRAM (2/2) (CK-94)
S
LCD UNIT
PANEL 2.8V 5
78
IC1601
Q1606, 1607 D1609
TRV6/TRV6E/TRV20E
DC/DC CONVERTER
EMERGENCY DETECT
T1601
(4-107)
P UNREG
80
Q1612 SWITCHING
TRV11/TRV11E/TRV20/TRV20E L1604
L1608
A 3.1V
L1607
D 3.1V
PANEL 2.8V 23 PANEL -15.3V 25 PANEL 13.3V 26 PANEL 4.6V
5 D1607 RECT
PD-123 BOARD
VCC(0)1234
OUT7-1
64
2
VCC(0)5678
OUT7-2
1
28
VCC
-IN7
IC2104
28
Q1621 SWITCHING
EVF 13.3V 19
13
43 AU 4.6V 44
RGB DRIVE
Q1613 SWITCHING
7
(4-96) 8
CN2173 CN2101
TRV20
L2104
PANEL 4.6V 8
LCD UNIT
23 PANEL -15.3V
7
4
3
L2103
PANEL 13.3V
1
6 P UNREG
2
1
(4-96)
12
VSS(0)1234
57
VSS(0)567
3
46 L1608
L1605
49
VDD(0)123
60
VDD(0)567
OUT3-1
53
OUT3-2
54
IC1602
Q1622 SWITCHING
CN2176
28
8
+IN8
7
-IN8
IC2171
3
TRV11/TRV11E
OUT8
INVERTER BLOCK
5
BACK LIGHT DRIVE
Q2172,2173
(4-93)
AU 2.8V 48 D 1.5V 49
54
Q1614 SWITCHING
OUT2-1
50
OUT2-2
51
-IN2
BLON 2
L1606
L1612
AU 2.8V
L1610
A 2.8V
L1609
Q1623 SWITCHING
D1610,1613 -15.3V REG
VREF
27
56
4
5
1
6
-IN4
37
33
VB
34
RT
35
VTR DD ON
IC2201
COMP
11
CT
OUT1-1
47
OUT1-2
48
-IN1
44
RP 4.6V CAM 15V(*2)
L1617
PANEL 13.3V
L1618
D1612 RECT
EVF 13.3V
*1
D1611(2/2) RECT
EVF 13.3V CAM -6.5V(*1) CAM -7.5V(*2)
Q1635,1639,1643
3
Q1609 SWITCHING
-6.5V/-7.5V REG
*2 L1603
L1615
Q1618 SWITCHING
PANEL 4.6V
L1614
A 4.6V
L1616
RP 4.6V
L1613
AU 4.6V EVF BL 4.6V
29
CTL1-6,8
30
CTL7
CAM DD ON Q1610 SWITCHING
L1601
CAP VS
INVERTER
CAM 12V(*1)
12V REG CN1604 21
R1693,1694
7
20
8
17
11
EVF BL 4.6V
A 4.6V
46
*2
8
D 3.1V
40
41
*2 OUT4
2
LCD UNIT
38
EMERGENCY DETECT
D1611(1/2) RECT
VREF
TRV11/TRV11E/TRV20
BACK LIGHT DRIVER
EVF 2.8V PANEL -15.3V
44 T1602
OUT6-1
61
OUT6-2
62
+IN6
18
Q1619 SWITCHING
Q1647,1649, 1650,1653 *1
EVF 13.3V EVF VCC
16
EVF 2.8V CN1603 11
22 24
19
CAP ERROR Q1611 SWITCHING
CN2201
CN2202
64 L1602
CAP VS
66
DRUM VS
CAP ERROR
21 68
LB-64 BOARD
11
22 24
19
21 L1803
CN002
OUT5-1
58
OUT5-2
59
+IN5
22
58
Q1620 SWITCHING
DRUM VS
60 DRUM ERROR 62
DRUM ERROR
CN009 FOR ADJUSTMENTS
EVF BL+
3-11
IC1803
RGB DRIVE
TIMING GENERATOR
CAM 12V(*1) CAM 15V(*2) 36
CAM -6.5V(*1) CAM -7.5V(*2)
2 EVF BL3
16
IC1802 (4-54)
VC-241 BOARD(1/2) VC-240 BOARD(1/2)
TO POWER BLOCK DIAGRAM (2/2) (VC-240)*2 (VC-241)*1
(SEE PAGE 3-13,3-15)
PANEL 2.8V Q1632,1637 1641
43
Q1608 SWITCHING
D 1.5V
D 2.8V
Q1629
(4-86)
D 2.8V
56
L1611
RECT
CN2174
A 2.8V
47
40
Q1605 SWITCHING
LCD INDICATOR DRIVE
D 1.9V
51
Q2102 2106 2103
XC SAVE
4
(4-109)
1.5V REG -IN3
45
Q1627,1628
5 TIMING GENERATOR
50
D 1.9V
52
D1606 RECT
IC2105
EVER 3.0V
46
D1608 RECT
24
L2102
PANEL 2.8V 5 TO POWER BLOCK DIAGRAM (2/2) (CK-92)
55
34
(4-54)
A 3.1V 42
*1 *2
CN1603
3-12
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
3-7. POWER BLOCK DIAGRAM (2/2) (DCR-TRV6/TRV6E/TRV11/TRV11E) VC-241 BOARD(2/2)
CN008 38
SHOE UNREG 8
IC1104
37
(4-62)
INTELLIGENT ACCESSORY SHOE
TRV11/TRV11E
HI CONTROL MS VCC 28 SHOE ON BATT SIG INIT CHARGE ON VTR DD ON CAM DD ON FAST CHARGE BATT XEXT SW BATT UNREG
27 73 69 65
IC1102
(4-61)
67 71 75
IC1101
D1103
76
REG
2
ACV SENS
IB SO
49
IB SI
48
INIT CHARGE ON
25
VTR DD ON
29
5
XRESET
38
3
31 42
6
54
7
IC1103
BATTER IN DETECT
REG
51
63 87
VDD
4
(4-61)
61
CAM DD ON
28
FAST CHARGE
50
POWER
4
MT 4.75V KEY ILLUMINATION LED
17 RV51 D 2.8V
7
ZOOM VR
BATT/XEXT
66
XVTR MODE SW
14
3
4
XCAM+STBY SW
15
1
2
XPHOTO STBY SW
20
5
1
LANC I/O UNREG
1
BATT SIG I/F
12
CONTROL SWITCH BLOCK(FK-30150)
CN064
BATT IN
8
70 72
MEMORY STICK
1 CN062
Q1104
D62-70
D1102
55
VTR UNREG
81
15
D1104 53 MT 4.75V
91
SHOE ON
(4-61)
RESET 3
90
BATT SENS
OFF
LANC DC
14
VCC
S1
CAMERA
POWER
MEMORY
TRV11/TRV11E
XLANC ON
Q1106
74
CONTROL SWITCH BLOCK (PS-30150)
VCR
8
D 2.8V
CK-92/94 BOARD
7
CHIME PWR CONT
92
VTR DD SENS CN003
Note : CK-92 BOARD : TRV11/TRV11E CK-94 BOARD : TRV6/TRV6E PD-123 BOARD : TRV11/TRV11E PD-124 BOARD : TRV6/TRV6E
S100-106 D 2.8V
SHOE UNREG
7
40 12
30
SHOE UNREG 31 21
P UNREG
50
78
PANEL 2.8V
PANEL 13.3V PANEL 4.6V
2
VTR UNREG
21
PANEL 4.6V 8
38 14
25
PANEL 2.8V Q1011
26
REG
5
32 20
LANC DC
PANEL -15.3V 7
36 16
28
PANEL 13.3V 6
25 27
EVF 13.3V
19
(4-64) 43 AU 4.6V
SW
CONTROL SWITCH BLOCK(FC-30150)
BT3201 LITHIUM BATTERY
34 18 EVF 13.3V
7 CN100
RESET
BTT LI 3V
80 PANEL -15.3V
CN3203
S3218
31
44
IC1002
(XYZ) AUDIO I/O
AUDIO ADC&DAC
12
24 28
(4-64)
IC1001
P UNREG
TO POWER BLOCK DIAGRAM (1/2) (PD-123/124)
CN3202 EVER 3.0V 5
5
47 CN3201
CN3205
46
IC502 50
IC501
52 45
(4-60)
A 2.8V
XREEL HALL ON
D2071,2072
JK-188 BOARD CN001 21 21
5
AU 2.8V TO POWER BLOCK DIAGRAM (1/2) (DD-137)
D 2.8V
AU 2.8V
48
(4-105)
12
IC002
D 1.5V
9
9 A 4.6V
D 2.8V
MIC AMP
13 13
13 LANC DC
51
28 28
(4-106)
27
(4-33)
54
CN2071
56
(SEE PAGE 4-12)
59 59
EVER 3.0V
IC2091
A 2.8V
60 60
IC903 D 3.1V
IC1301
IC301
IC361
(ALIGN)
(TAKO)
(CAIN)
(LIP)
A/D CONV.
VIDEO LINE IN/OUT AMP
DV SIGNAL PROCESS
DV INTERFACE
38
IC302
IC1901
CHARACTER GENERATER
IR TRANSMITTER
RP 4.6V
44
A 4.6V
46
D 3.1V
(4-48)
(4-50)
(4-36)
J2002 SE3501,3502
PITCH,YAW SENSOR AMP
MA-385 BOARD
FB753
(4-55)
TRV6/TRV6E
MT 4.75V
(4-56)
D 1.9V D 2.8V
IC401
IC402
A 2.8V
L801
DRUM VS
CAM 12V CAM -6.5V
IC801
IC753
IC751
68 58
FC RST LED
60 DRUM ERROR
DRUM ERROR
TRV11/ TRV11E
(4-29)
IC802
66 CAP ERROR
(4-29)
CAP ERROR
64
62
L201
ZM RST LED
16
CAMERA CONTROL
EEPROM
IC752
(BIRDS+) CAMERA SIGNAL PROCESS
REG
CAP_VS
IC701 (GCAM3) S/H,AGC A/D CONV.
16M SDRAM
Q802
18
CAPSTAN MOTOR DRIVE, CAP FG AMP
Q1109 CHIME VDD
(RABI)
EVF 13.3V
CAP VS
LANC/DIGITAL I/O
(4-89)
(4-52)
TRV11/TRV11E
RP 4.6V
41
(4-36)
EXCEPT AEP/UK MODEL
REMOTE COMMANDER RECEIVER
PITCH,YAW SENSOR
IC3051
40 A 4.6V
SE-94 BOARD
AU 2.8V 9
49
R052
22 MF VCC
12 12
MANUAL FOCUS AENSOR
4
47 FB501
PH081,082
CN2051
21
VTR UNREG
22 22
(4-59)
R051
IR LED
CN3001
DRUM VS
52 54 51
DRUM MOTOR DRIVE DRUM FG,PG AMP LOADING MOTOR DRIVE REEL FG AMP TAPE TOP,END DET DRUM,CAP ERROR AMP
D 2.8V
R424
MT 4.75V
36
21
(4-32)
MF LED
(4-31)
(4-32)
SENSOR VCC
VTR UNREG
15
18
4PIN CONNECTOR
19
T REEL, S REEL SENSOR
13
TAPE LED
Q402
XREEL HALL ON
A 2.8V
105
MECHA CONTROL
EEPROM
CHIME PWR CONT
D 1.9V
TAPE LED A
(4-25)
CN006
J MECHA DECK
34
(SEE PAGE 4-55)
(4-25) A 3.1V
RP 4.6V
A 4.6V
42 MT 4.75V
L102
L203
IC702
A 2.8V
FB101
D 2.8V
D 1.9V
FB201
IC201 SHUTTER DRIVE
IC202 IC203
IC204 FOCUS/ZOOM MOTOR DRIVE
IRIS DRIVE IRIS HALL AMP
FP-219
TIMING GENERATOR
IC102
IC101 (TRF)
REC/PB AMP
EQ, A/D CONV. PLL
(4-38)
(4-13) CAM 12V
(TRW)
(FLEXIBLE)
IC3000
21 21
CAM -6.5V 8
(4-37)
CCD IMAGER
8
TRV11/TRV11E
IC1403
IC1405
IC1407
RS232C I/F
16Mbit SDRAM
4Mbit FLASH
IC1406
IC1404
FC RST LED LENS ASSY
D 1.5V
(4-43)
(4-45)
(SHIORI) DIGITAL STILL PROCESS
(4-45)
DIGITAL STILL CONTROL
(4-46)
(4-44)
33
MS VCC ON
Q204 CN3000 D 2.8V
16
FOCUS RESET SENSOR
8
ZOOM RESET SENSOR
FC SENS VCC 33 33
ZM RST LED Q203
Q1406,1407
D 3.1V
ZM SENS VCC 41 41 CN3001
16
CN701
3-13
3-14
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
3-8. POWER BLOCK DIAGRAM (2/2) (DCR-TRV20/TRV20E) VC-240 BOARD(2/2)
CN008 38
SHOE UNREG 8
IC1104
37
(4-62)
INTELLIGENT ACCESSORY SHOE
HI CONTROL MS VCC 28 SHOE ON BATT SIG INIT CHARGE ON VTR DD ON CAM DD ON FAST CHARGE BATT XEXT SW BATT UNREG
27 73 69 65
IC1102
(4-61)
67
91
ACV SENS
SHOE ON
75
IC1101
D1103
76
49
IB SI
48
5
7
IC1103
55
BATTER IN DETECT
REG
6
31 42 51 63 87
4
61
VDD
(4-61)
70 UNREG
1
POWER
MT 4.75V
VTR DD ON
29 28
FAST CHARGE
50
4
12
CONTROL SWITCH BLOCK(FK-30150)
RV51 D 2.8V
7
ZOOM VR
(SEE PAGE 4-91)
BATT/XEXT
66
XVTR MODE SW
14
3
4
XCAM+STBY SW
15
1
2
XPHOTO STBY SW
20
5
1
CN064
BATT IN
8
LANC I/O 72
D62-70 15
25
CAM DD ON
XRESET
38
D1102
54
BATT SIG I/F
KEY ILLUMINATION LED
3
3
MEMORY STICK
1 CN062
Q1104
17
RESET
REG
2
53
VTR UNREG
IB SO
INIT CHARGE ON 71
81
(4-61)
D1104
MT 4.75V
90
BATT SENS
VCR OFF CAMERA
14
LANC DC
VCC
POWER
XLANC ON MEMORY
Q1106
74
CONTROL SWITCH BLOCK (PS-30150)
S1
(SEE PAGE 4-91)
8
D 2.8V
CHIME PWR CONT
92
CK-92/94 BOARD
7
VTR DD SENS CN003
Note : CK-92 BOARD : TRV20 CK-94 BOARD : TRV20E PD-123 BOARD : TRV20 PD-124 BOARD : TRV20E
S100-106 D 2.8V
SHOE UNREG
7
40 12
30
SHOE UNREG 31 21
P UNREG
50
78
PANEL 2.8V PANEL -15.3V PANEL 13.3V PANEL 4.6V
2
CONTROL SWITCH BLOCK(CF-30150)
BT3201 LITHIUM BATTERY
(SEE PAGE 4-83)
VTR UNREG
21
PANEL 4.6V 8
38 14
25
PANEL 2.8V Q1011
26
REG
5
32 20
LANC DC
PANEL -15.3V 7
36 16
28
TO POWER BLOCK DIAGRAM (1/2) (PD-123/124)
PANEL 13.3V 6
34 18 EVF 13.3V
SW CN100
RESET
BTT LI 3V
80
7
CN3203
S3218
31
25 27
EVF 13.3V
19
P UNREG 12
24 28
CN3202
43 AU 4.6V
(XYZ) AUDIO I/O
AUDIO ADC&DAC
EVER 3.0V 5
5
47 CN3201
CN3205
46
(4-64) D 1.9V
(4-64)
IC502
50
IC501
52 A 2.8V
45
(4-60)
A 2.8V
105
XREEL HALL ON
D2071,2072
JK-188 BOARD 21 21 22 22
(4-59)
5
21
VTR UNREG
PH081,082
CN2051
R051
IR LED
CN3001
CN001
MECHA CONTROL
EEPROM
(4-105)
22
MANUAL FOCUS AENSOR
4 R052
SE-94 BOARD
47 AU 2.8V D 2.8V
12 12 AU 2.8V 9
9
9 A 4.6V
49
D 2.8V
MIC AMP
13 13
13 LANC DC
51 D 1.5V
12
AU 2.8V
48
IC2002
MF VCC
FB501
28 28
(4-106)
27
54
CN2071
56
59 59
EVER 3.0V
IC2091
A 2.8V
60 60
IC903 D 3.1V
IC1301
IC301
IC361
(ALIGN)
(TAKO)
(CAIN)
(LIP)
A/D CONV.
VIDEO LINE IN/OUT AMP
DV SIGNAL PROCESS
DV INTERFACE
38
IC302 CHARACTER GENERATER
IC1901
IC3051
IR TRANSMITTER
REMOTE COMMANDER RECEIVER
PITCH,YAW SENSOR
J2002 SE3501,3502
PITCH,YAW SENSOR AMP
LANC/DIGITAL I/O
MA-385 BOARD
(4-89)
40 A 4.6V
RP 4.6V
44
A 4.6V
46
D 3.1V
(4-48)
(4-50)
(4-33)
(4-36)
(4-36)
(4-52) (4-55)
RP 4.6V
41
MT 4.75V
(4-56)
D 1.9V D 2.8V
IC401
IC402
A 2.8V EVF 13.3V L801
CAP VS
IC803
66 CAP ERROR DRUM VS
CAM 15V CAM -7.5V
DRUM ERROR
(4-21)
CAP ERROR
IC802
IC801
IC752
EEPROM
2.4V REG
IC751
68
2.4V
58
EVR
CAMERA CONTROL
60 DRUM ERROR
(4-21)
64
62
(4-22) 36
(4-24)
MF LED
21
(CARILLON) CAMERA SIGNAL PROCESS RC PROCESS
IC702
CAP_VS
IC701 A/D CONV.
16M SDRAM
18
CAPSTAN MOTOR DRIVE, CAP FG AMP
DRUM VS
52 54 51
CHIME VDD
DRUM MOTOR DRIVE DRUM FG,PG AMP LOADING MOTOR DRIVE REEL FG AMP TAPE TOP,END DET DRUM,CAP ERROR AMP
SENSOR VCC
VTR UNREG
(4-17)
18
4PIN CONNECTOR
19
T REEL, S REEL SENSOR
13
TAPE LED
Q402
D 2.8V
Q801
R424
MT 4.75V
(4-23)
Q1109
(RABI)
XREEL HALL ON
(SEE PAGE 3-12)
44
IC1002
CHIME PWR CONT
TO POWER BLOCK DIAGRAM (1/2) (DD-137)
IC1001
(4-17)
TAPE LED A CN006
J MECHA DECK
34
(SEE PAGE 4-55) A 3.1V
RP 4.6V
A 3.1V
42
MT 4.75V
A 2.8V
L203
D 2.8V FB201
CD-252 BOARD
D 1.9V
L102
A 2.8V
FB101
IC204 FOCUS/ZOOM MOTOR CONTROL
(4-19)
IC1403 RS232C I/F
IC201
IC202 IC203
IC205
FOCUS/ZOOM MOTOR DRIVE SHUTTER DRIVE ND FILTER DRIVE
(4-19)
IC1404 64M SDRAM
CAM DD ON
ND FILTER PRE DRIVE, ND HALL AMP
IC102
IC1407 JPEG
(4-19)
IC1408 16M DRAM FAST PAGE
(4-39)
(4-41)
(4-40)
(4-40)
5
CCD IMAGER (4-11)
IC103
DIGITAL STILL CONTROL FB1401
IC1411 118
SHUTTER SOUND
(4-39)
(4-40)
IC104
(4-18)
IC703
LENS ASSY 10 10
(4-11)
A 2.8V
12 12 3.3V REG
D 3.3V
3
(4-11) MR VCC
3-15
F MR VCC 7 Z MR VCC 18
L151 CN701
FOCUS MR
CN151
11 11
49 49 FB1406
TIMING GENERATOR
CDS,AGC
MEMORY STICK I/F
(4-42)
IC102
AMP
IC1409 IC1410
D 3.1V
16
IC101
Q1404,1405
IC1412
EEPROM
Q103,104
(4-11)
(4-37)
IC1406
(4-40)
8
5
CAM -7V
2 D 2.8V
8
CAM 15V
EQ, A/D CONV. PLL
(4-38)
7
MS VCC ON
(TRF)
REC/PB AMP
IRIS DRIVE IRIS HALL AMP
(4-20)
IC101
(TRW)
7
CN101
3-16E
ZOOM MR
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM-1 11
12
13
14
15
16
17
CD-252 BOARD
CCD IMAGER
C NIGHT SHOT OFF
37
GND
39
F MR A
41
GND
43
IRIS DRIVE-
45
IR SW OUT
38
F MR B
40
TEMP OUT
42
IRIS DRIVE+
44
IRIS BIAS+
IRIS BIAS-
46
47
IRIS HALL+
IRIS HALL-
48
49
MR VCC
Z MR A
50
51
TEMP/MR GND
Z MR B
52
53
ND BIAS+
GND
54
55
ND HALL-
ND BIAS-
56
57
ND HALL+
GND
58
59
ND DRIVE+
ND DRIVE-
60
ZOOM-
ZOOM+
FOCUS+
FOCUS-
IR_SW_OUT
FP-219 FLEXIBLE BOARD
CCD IMAGER
50P
1
V3
V2
2
3
V4
V1
4
5
VSHT
V_DRAIN
6
7
HDR_GND
-6.5V
8
9
H2
HDR_GND
10
11
H1
HDR_GND
12
13
RG
HDR_GND
14
15
CCD_GND
CCD_GND
16
17
CCD_OUT
CCD_GND
18
19
CCD_GND
CCD_GND
20
21
12V
CCD_GND
22
OFF
23
S_GND
S_GND
24
25
ZM_XA
ZM_XB
26
27
ZM_A
ZM_B
28
VC-240 BOARD VC-241 BOARD
24P
5
4
3
29
Gnd
NightShot_Vcc
30
31
FC_SENS_OUT
THERMO_OUT
32
33
FC_SENS_Vcc
Gnd
34
35
FC_XA
FC_XB
36
37
FC_A
FC_B
38
39
ZM_SENS_OUT
Gnd
40
41
ZM_SENS_Vcc
HALL(+)
42
43
BIAS(+)
HALL(-)
44
45
BIAS(-)
Gnd
46
47
Gnd
DRIVE(-)
48
49
DRIVE(+)
SLOW SHUT
50
CN701 50P
1/24 CH BLOCK
13/24 MS-2 BLOCK 14/24 MS-1 15/24 MS-2 16/24 IN BLOCK 17/24 IO BLOCK 18/24 IR BLOCK
4/24 CA BLOCK 5/24 CH BLOCK 6/24 LD BLOCK 7/24 CM BLOCK
2
S VIDEO
AU_GND
2
AU_GND
4
5
SHOE_MIC_L
7
EXT_MIC_JACK
9
AU_2.8V
XMIC_MONO
J2002
8
MF_B
10
MF_LED
12
F_TALLY_LED
14
CN101
10P
CN005
10P
4
3
2 XOSD_SCK
1
5
XCS_LCD_DRIVER
OSD_SO
6
16
LCD_COM/XDATA
17
7
18
C-SYNC/XHD
EVER_3.0V
19
XVD
8
20
REG_GND
REG_GND
21
REG_GND
9
22
REG_GND
PANEL_B
23
31
HI_SO
32
CN007
16
EVF_RGT
18
19
EVF_13.3V
EVF_DCG/CLR
20
21
EVF_2.8V
EVF_BL-
22
23
PANEL_2.8V
EVF_BL+
24
25
PANEL_-15.3V
PANEL_13.3V
26
27
SHOE_ON
PANEL_4.6V
28
29
SHOE_GND
SHOE_UNEREG
30
31
SHOE_GND
SHOE_UNEREG
32
33
REG_GND
CAM_-7.5V
34
35
REG_GND
CAM_15V
36
37
REG_GND
D_3.1V
38
39
REG_GND
D_3.1V
40
41
RP_4.6V
A_3.1V
42
43
AU_4.6V
A_4.6V
44
45
A_2.8V
A_4.6V
46
47
A_2.8V
AU_2.8V
48
49
D_2.8V
D_1.9V
50
51
D_2.8V
D_1.9V
52
53
MT_4.75V
D_1.5V
54
55
MT_4.75V
D_1.5V
56
57
MT_4.75V
DRUM_VS
58
59
MT_GND
DRUM_VS
60
61
MT_GND
DRUM_ERROR
62
63
MT_GND
CAP_VS
64
65
VTR_DD_ON
CAP_VS
66
67
CAM_DD_ON
CAP_ERROR
68
69
INIT_CHARGE_ON
VTR_UNREG
70
71
FAST_CHARGE
VTR_UNREG
72
73
BATT_SIG
VTR_UNREG
74
75
BATT_XEXT_SW
BATT_UNREG
76
77
P_UNREG_GND
P_UNREG
78
79
P_UNREG_GND
P_UNREG
80
B TO(2/2)
XX
XDS_FLASH CAM_XRESET CAM_RXD CAM_TXD CAM_TEST_A XCS_MC_FLASH XDRP_SCK DRP_SO DRP_SI MC_F_BUSY REG_GND HI_XRESET HI_RXD HI_TXD HI_TEST_A
27P
17
18
19
20
21
22
23
24
25
26
27
17
18
19
20
21
22
23
24
25
26
27
CAP_U
CAP_U
CAP_U
CAP_U
N.C.
FG1
FG_VCC
FG_VCC
FG2
FG_GND
FG_GND
FG_GND
16 16 VHE-
FG_GND
15 15 WHE-
FG2
14 14 CAP_W
FG_VCC
13 13 CAP_W
FG_VCC
12 12 CAP_W
FG1
11 11 CAP_W
N.C.
HE_GND 10 10 HE_GND
CAP_U
WHE+ 9 9 WHE+
CAP_U
VHE+ 8 8 VHE+
CAP_U
UHE+ 7 7 UHE+
CAP_U
HE VCC 6 6 HE VCC
VHE-
UHE5 5 UHE-
WHE-
CAP_V 4 4 CAP_V
CAP_W
CAP_V 3 3 CAP_V
CAP_W
CAP_V 2 2 CAP_V
CAP_V 1 1 CAP_V
TAPE_TOP 27 27 TAPE_TOP
TOP/END_GND 26 26 TOP/END_GND
TAPE_END 25 25 TAPE_END
SREEL+ 24 24 SREEL+
SREEL23 23 SREEL-
HALL_GND 22 22 HALL_GND
TREEL21 21 TREEL-
TREEL+ 20 20 TREEL+
HALL_VCC 19 19 HALL_VCC
CHIME_VDD 18 18 CHIME_VDD
CHIME_SDA 17 17 CHIME_SDA
CHIME_SCK 16 16 CHIME_SCK
XREC_PROOF 15 15 XREC_PROOF
MIC/REC_SW_GND 14 14 MIC/REC_SW_GND
TAPE_LED_A 13 13 TAPE_LED_A
TAPE_LED_K 12 12 TAPE_LED_K
XCCDOWN_SW 11 XCCDOWN_SW 11
SW_COM/SW_GND 10 10 SW_COM/SW_GND
MODE_SW_C 9 9 MODE_SW_C
MODE_SW_B 8 8 MODE_SW_B
MODE_SW_A 7 7 MODE_SW_A
DEW6 6 DEW-
DEW+ 5 5 DEW+
LM_UNLOAD 4 4 LM_UNLOAD
LM_UNLOAD 3 3 LM_UNLOAD
LM_LOAD 2 2 LM_LOAD
LM_LOAD 1 1 LM_LOAD
DRUM_W 10 DRUM_W 10
DRUM_W 9 9 DRUM_W
DRUM_V 8 8 DRUM_V
DRUM_V 7 7 DRUM_V
DRUM_U
58
6
YS_OUT
6
PS_OUT
DRUM_U
57
DRUM_U
56
5
54
C_RESET
5
52
REG_GND
REG_GND
DRUM_U
AV_GND
REG_GND
55
M COM
VIDEO_I/O
53
4
51
4
50
M COM
R_IO
FG/PG COM
L_IO
3
48
49
3
AV_JACK_IN
FG
XHP_JACK_IN
2
46
47
2
HP_L
FG
HP_R
PG
44
45
1
DV_GND
1
DV_GND
PG
42
43
GND
TPA
10
TPB
10
40
41
GND
NTPA
XEVEN
NTPB
9
38
39
9
DV_GND
XEVEN
DV_GND
YEVEN
36
37
8
XSJACK_IN
8
S_Y_OUT
YEVEN
34
35
GND
S_Y_GND
7
32
REG_GND
7
S_C_OUT
33
GND
30
31
S_C_GND
XODD
KEY_AD2
6
REG_GND
6
28
29
XODD
LANC_DC
YODD
REG_GND
5
26
27
5
24
LANC_SIG/232C_RD
YODD
22
REG_GND
GND
25
20
XLANC_JACK_IN
4
LANC_GND/232C_TD
4
23
18
VTR_UNREG
GND
VTR_UNREG
XSDL
21
16
REG_GND
YSDL
IR_DRV_CL
GND
19
REG_GND IR_DRV_EM
3
REG_GND
2
SIRCS_SIG
17
1
A_4.6v
15
LM_UNLOAD
LM_UNLOAD
DEW+
DEW-
MODE_SW_A
MODE_SW_B
MODE_SW_C
SW_COM/SW_GND
4
5
6
7
8
9
10
A_2.8V
A_2.8V CN3001
3
59
FG/PG COM
M901 FG PG VIDEO HEAD
60
60P
M DRUM MOTOR
LM_LOAD
INFINITY
2
MAN
TRV6 MODEL:DCR-TRV6 TRV6E MODEL:DCR-TRV6E TRV11 MODEL:DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL:DCR-TRV20 TRV20E MODEL:DCR-TRV20E
S901 CN901 3P
LM_LOAD
AUTO
CN2001
(CC DOWN)
M902
REC PROOF HALL
Q902
Q901
TAPE TOP
TAPE END
M
FG
CAPSTAM MOTOR
D901
4P
1
INT MIC L
2
INT MIC GND
3
INT MIC R
4
INT MIC GND
1
MF_A
2
MF_B
IC2091
3
GND
R
4
MF_LED_A
5
MF_LED_B
TAPE LED
M903
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1 MIC_R
AU_GND
MIC_L
AU_GND
SHOE_MIC_L
XMIC_MONO
EXT_MIC_DET
ZOOM_MIC_CONT
AU_2.8V
MF_B
MF_A
MF_LED
A_4.6v
XF_TALLY_LED
XSIRCS_IN
GND
GND
20 GND
IR_EM
IR_DRV
21 VTR_UNREG
22 VTR_UNREG
23 GND
24 232C_TD
25 LANC_JACK_IN
26
27
CN2071
REMOTE COMMANDER RECEIVER
28P
5P
LANC_SIG
KEY_AD2
MIC
LANC_DC
28
MIC
CN2051
MANUAL FOCUS SENSOR
27P
3
13
1
J2001
LASER LINK
SE-94 BOARD
CN006
2
MF_A
FOCUS
N
14
EVF_HST
EVF_PWM
6
ZOOM_MIC_CONT
S903 S2061
MIC (R)
EVF_HCK2
EVF_LED_K
17
MT_4.75V
7
1
MA-385 BOARD
DIGITAL I/O
MIC (L)
EVF_DET
15
CN001 60P
J3002
MIC901 MIC UNIT
13
J3004
K
M
24
33
XRESET_SW
CN004
GND
DV IN/OUT
MIC
XHI_SCK
34
PANEL_2.8V
22/24 HI BLOCK 23/24 AU BLOCK 24/24 CN BLOCK
XSDL
J3003
AUDIO/VIDEO
PLUG IN POWER
12
RF_MON
20
YSDL
J
L
EVF_HCK1
J3001 11
LANC
EVF_VCC
GND
19
16
MIC_R
11
6
RF_IN/LANC_JACK_IN
18
15
MIC_L
10
SWP
13
3
EVF_BLK
GND
12
1
EVF_GND
JIG_TDO
11
JK-188 BOARD
8
9
JIG_TDI
14
I
EVF_B
TCK
17
TRV6/6E/11/11E MODEL
EVF_VST
TMS
10
1
CPC
21/24 MC BLOCK
10/24 JC-2 BLOCK 11/24 RF BLOCK 12/24 MS-1 BLOCK
7
PANEL_COM
16
19/24 VF BLOCK 20/24 MD BLOCK
8/24 CA BLOCK 9/24 JC-1 BLOCK
4
EVF_R
EVF_EN
XHD/PSIG
8
DRIVE(-)
DRIVE(+)
Gnd
HALL(-)
BIAS(-)
BIAS(+)
ZM_SENS_Vcc
ZM_SENS_OUT
Gnd
FC_B
FC_A
FC_XB
FC_XA
Gnd
FC_SENS_Vcc
THERMO_OUT
FC_SENS_OUT
Gnd
NightShot_Vcc
ZM_B
ZM_A
CN3000
ZM_XB
ZM_XA
HALL(+) 6
25
H_START
9
7
8
XCS_LCD
PD_VCO
9
6
9
26
PANEL_VG
8
5
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
P_UNREG
7
14
2/24 LD BLOCK 3/24 CM BLOCK
EVF_G
EVF_VCK2
GND
13
(TRV6/6E/11/11E MODEL)
2
EVF_STB
5 EVF_VCO
12
(TRV20/20E MODEL)
EVF_COM
3
1
EVF_VG
4
SUPER NIGHT SHOT
CN002 80P
TRV20/20E MODEL
3
H
27
EFN_BL-
2
NIGHT SHOT ON
P_UNREG
3
1
G
28
EVF_BL+
15
LENS UNIT
XHD_OUT
LANC_SIG
2
11
CN101
20P
1
10
F
29
35
KEY_AD7
30
36
PANEL_13.3V
51P
6
E
10
36
REG_GND
FOCUS+
11
FOCUS-
PANEL_G
34
35
12
ZOOM+
CN003
39P
FLEXIBLE
REG_GND
ZOOM-
21
13
32
33
37
1
GND
KEY_AD6
2
S.N.SHOT
38
3
XCAM_STBY_SW
30
31
PANEL_-15.3V
4
N.C.
FRQ
39
5
XVTR_MODE_SW
GND
KEY_AD5
6
XS/S_SW
28
29
40
7
XPHOTO_STBY_SW
ZV1
PANEL_4.6V
8
GND
ZSG1
41
9
D_2.8V
26
27
KEY_AD4
10
ZOOM_AD
TG_VD
42
11
GND
TG_FLD
D_2.8V
12
XPHOTO_FREEZE
24
25
43
13
MS_LED_VCC
22
TG_ID
KEY_AD3
14
XMS_ACCSEE
20
CAM_SI
TG_HD
44
15
GND
CAM_SCK
GND
23
REG_GND
16
KEY_AD_1
CSUB
21
45
17
MT_4.75V
19
CN008
REG_GND
18
FK_LED_ON
18
46
19
MT_4.75V
16
CAM_SO
REG_GND
20
KEY_AD_0
14
CS_CAM
GND
47
21
IR_LED_ON
XCAM_RST
MCK
17
REG_GND
22
IR_LED_VCC
GND
15
48
23
XEJECT_SW
13
SP+
24
GND
12
49
25
SCLK
A_2.8V
REG_GND
26
DIO
D_3.3V
50
27
GND
11
SP-
28
BS
10
51
29
MS_IN
8
A_2.8V
DIAL_B
30
MS_VCC
CAM_15V
PBLK
DIAL_A
31
SHOE_GND
6
CAM_DD_ON
9
BATT_LI_3V
32
SHOE_GND
GND
33
CAM_-7V
7
1
2
3
IR_SW
F_MR_VCC
F_MR_A
F_MR_B
TEMP/F_MR_GND
5
CN701 60P
5
4
5
6
7
8
TEMP
IRIS_DRIVE+
IRIS_DRIVE-
IRIS_BIAS+
IRIS_BIAS-
IRIS_HALL-
IRIS_HALL+
Z_MR_VCC
Z_MR_B
Z_MR_GND
Z_MR_A
ND_BIAS-
ND_HALL-
ND_BIAS+
ND_HALL+
4
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CN051
ND_DRIVE+
ND_DRIVE26
27
D
2
CCDout (-)
CN009
27P
ON
CCDout (+)
GND
CAP_W
LENS UNIT
GND
3
SHOE_MIC_L
B
60P
1
34
CN101 SUPER NIGHT SHOT
MIC_GND
S001
35
5
SHOE_MIC_R
4
GND
36
3
GND
GND
SHO_ID2
SLOW_SHUT
GND
5
37
SLOW_SHUT
4
SHO_ID1
3
FP-179
NS-10 BOARD 38
2
LANC_SIG
1
GND
39
GND
GND
N.C.
GND
2
SHOE_UNREG
1
20
A TO(2/2)
PSIG
5P
SHOE_UNREG
CN052
19
PANEL_R
C TO(2/2)
A
18
14
10
REG_GND
9
15
8
PANEL_VG
7
REG_GND
6
PANEL_COM
5
P_UNREG_GND
4
P_UNREG_GND
3
CAP_W
2
P_UNREG_GND
1
M LOADING MOTOR
S902 MODE SWITCH
DEW SENSOR
FP-100
FP-228
FLEXIBLE
FLEXIBLE
FP-102 FLEXIBLE
J-100 MECHANISM
16
4-1
4-2
FRAME SCHEMATIC DIAGRAM (1/2)
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
FRAME SCHEMATIC DIAGRAM-2 2
1
3
5
4
6
7
8
9
10
11
12
14
13
LCD902 CHARACTER DISPLAY
3
DIAL_B
13
2
DISP_VD
P_UNREG
12
3
GND
S3201 5
REG_GND
6
SP+
7
REG_GND
XCS_LCD_DAC
11
XHI_SCK
10
PC-119
5
PANEL_2.8V
HI_SO
9
HARNESS
6
PANEL_13.3V
8
7
PANEL_-15.3V
9
REG_GND
10
REG_GND
11
KEY_AD3
S3203
8
PANEL_4.6V
6
9
HI_SO
5
10
XHI_SCK
4
11
XCS_LCD_DAC
GND
3
12
P_UNREG
DISP_VD
2
13
P_UNREG_GND
PANEL_-15.3V
7
PANEL_13.3V PANEL_2.8V GND
MEMORY INDEX
5 24P
4
N.C.
5
BL_LOW
3
GRES
6
LED
2
GPCK
7
BL_GND
1
9
12
13
14
15
16
17
18
19
20
21
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
COM3
COM4
N.C.
8
11
7
SEG9
6
SEG6
10
5
SEG5
SEG8
4
SEG4
KEY_AD6
1/2 LCD/CN BLOCK
RESET
10
18
PANEL_13.3V
2/2 RGB/TG BLOCK
VCOM
11
19
KEY_AD7
VBC
12
20
PANEL_2.8V
STBYB
13
21
XRESET_SW
SRT
14
22
P_UNREG_GND
OE
15
23
P_UNREG_GND
CLR
16
24
P_UNREG_GND
MCLK
17
25
PSIG
HCNT
18
26
XHD_OUT
VR
19
27
P_UNREG
VG
20
28
P_UNREG
VB
21
29
XCS_LCD
VSS
22
30
XHI_SCK
VDD
23
31
HI_SO
VSH
24
32
REG_GND
33
REG_GND
CN2176
PANEL_COM
MEMORY+
10
PANEL_VG
9
PANEL_R
S3207
8
PANEL_G
DIGITAL EFFECT
7 8 9 10 11
2
OSD_SO
12
1
12P
OSD_SO XOSD_SCK XCS_LCD_DRIVER LCD_COM/XDATA EVER_3.0V PANEL_B PANEL_G PANEL_R PANEL_VG PANEL_COM XHD_OUT PSIG
S3215 MEMORY DELETE
TITLE REG_GND S3211 35
XVD
36
C-SYNC/XHD
37
PANEL_COM
38
REG_GND
39
PANEL_VG
40
REG_GND
S3216 MENU
END SEARCH
S3212
S3217 DISPLAY
MEMORY MIX
S3213
DD-137 BOARD
S3218
LB-64 BOARD
CONTROL SWITCH BLOCK (FK-30150)
41
PANEL_R
42
REG_GND
43
PANEL_G
44
REG_GND
45
PANEL_B
1
EVF_EN
EVF_COM
2
COM
27
1
COM
VDD
16
46
REG_GND
3
EVF_STB
EVF_G
4
G
26
2
G
VSS
15
47
EVER_3.0V
5
EVF_VCK2
EVF_R
6
R
25
3
R
VST
14
48
LCD_COM/XDATA
7
EVF_VST
EVF_B
8
B
24
4
B
VCK2
13
PB ZOOM
RESET
S3214
BT3201
CN1603
80P
CN1604
27P
CN2201
27P
CN2202
49
XCS_LCD_DRIVER
50
XOSD_SCK
S3209 MEMORY INDEX
51
OSD_SO
S3205
S3212 MEMORY PLAY
S3206
SP+
2
SP-
EVF_BLK
10
BLK
23
5
BLK
EVF_HCK1
12
HCK1
22
6
HCK1
13
EVF_DET
15
EVF_LED_K
2P
14
HCK2
21
7
HCK2
EVF_HST
16
HST
20
8
HST
17
EVF_PWM
EVF_RGT
18
RGT
19
19
EVF_13.3V
EVF_DCG/CLR
20
DCG/CLR
18
21
6P
PANEL_-15.3V
27
SHOE_ON
22
EN
17
24
STB
16
26
VCK2
15
PANEL_4.6V
28
VST
14
N.C.(XTALLY_LED)
A_2.8V
A_4.6V
46
47
A_2.8V
AU_2.8V
48
GND
EVF_BL_4.6V
44
GND
42
A_4.6V
KEY_AD4X
A_3.1V
AU_4.6V
6
RP_4.6V
43
KEY_AD4X
8
5
9
EVF_BL_4.6V
4
10
EVF_BL_GND
40
3
EVF_BL_GND
38
D_3.1V
GND
36
D_3.1V
REG_GND
GND
CAM_15V
REG_GND
39
2
REG_GND
37
1
35
D_2.8V
11
KEY_AD7
VDD
KEY_AD3
34
7
CAM_-7.5V
CTRL_B
REG_GND
6
33
CTRL_A
12
5
13
VSS
4
VSS
32
3
30
SHOE_UNEREG
GND
SHOE_UNEREG
SHOE_GND
GND
SHOE_GND
31
45
9 10
RGT DCG/CLR
11
EN
12
STB
13
VCK2
14
VST
EVF_BL_GND EVF_BL_GND EVF_BL_4.6V
7
21
EVF_BL_4.6V
6
22
N.C.(XTALLY_LED)
DET
5
23
DET
LED_K
4
24
LED_K
25
PWM
26
N.C.
1
27
N.C.
55
MT_4.9V
D_1.5V
56
FLEXIBLE
57
MT_4.9V
DRUM_VS
58
S97
59
MT_GND
DRUM_VS
60
VTR_DD_ON
CAP_VS
66
CAM_DD_ON
CAP_ERROR
68
69
INIT_CHARGE_ON
VTR_UNREG
70
71
FAST_CHARGE
VTR_UNREG
72
BATT_SIG
75
BATT/XEXT_SW
VTR_UNREG
74
BATT_UNREG
76
S103
P_UNREG_GND
P_UNREG
78
79
P_UNREG_GND
P_UNREG
80
5
SHOE_MIC_L
2
MIC_GND
3
SHOE_MIC_R
4
XPHOTO_STBY_SW
SHO_ID2
5
6
GND
SHO_ID1
6
7
2.8V
LANC_SIG
7
SHOE_UNREG
8
S61 OPEN/EJECT
LCD
8
ZOOM_AD
9
GND
EVF
S62 10
XPHOTO_FREEZE
11
MS_LED_VCC
12
XMS_ACCSEE
STOP S71
S63 13
GND
14
KEY_AD_1
15
MT_4.75V
PHOTO REW (FREEZ)
CONTROL SWITCH BLOCK (PS-30150)
(PHOTO REC) S64
FK_LED_ON PLAY
17
MT_4.75V
18
KEY_AD_0
19
IR_LED_ON
CN64
6P POWER XPHOTO_STBY_SW
1
XCAM_STBY_SW
2
20
IR_LED_VCC
21
XEJECT_SW
GND
3
XVTR_MODE_SW
4
XS/S_SW
5
OFF(CHG) S66 22
GND
23
SCLK
24
DIO
25
GND
26
BS
27
INS
16
MEMORY S67
S2 START/STOP
28
MS_VCC
29
SHOE_GND
30
SHOE_GND
EDITSEARCHLINE IN/OUT MODEL
TO(1/2)
1
ACV_GND
2
BATT_XEXT
3
31 J902 DC IN
SHOE_MIC_L
CN62
CN52
FRAME SCHEMATIC DIAGRAM (2/2)
32
MIC_GND
33
SHOE_MIC_R
34
SHO_ID2
35
SHO_ID1
VSS
1
2
BS
SCLK
2
3
VCC
4
DIO
5
36
LANC_SIG
N.C
6
37
INS
7
N.C
S72
3P BATT_UNREG
1
BATT_SIG
2
BATT_GND
3
J901 BATTERY TERMINAL
INS
3
DIO
4
BS
5
SHOE_UNREG
VSS
6
38
SHOE_UNREG
STATICS_GND
7
8
SCLK
39
N.C.
N.C.
8
9
VCC
10
VSS
S106
4-3
1 VCC
8P
10P
REC
SUPER LASER LINK
LCD BRIGHT+
VOLUME-
CAMERA
6
MEMORY MODEL S104
M
VCR
FF
S105 VOLUME+
S1
S65
S69,70
CN1602 77
XS/S_SW
LCD903
C 3P
S100 73
XVTR_MODE_SW
4
1
EDITSEARCH+
TO(1/2)
PROGRAM AE
N.C.
3
SHOE_GND
S68
ACV_UNREG
67
2
8P
PAUSE
2
65
3
20
3
B
R
19
N.C.
SEL/PUSH EXEC
4
18
N.C.
64
XCAM_STBY_SW
16
PWM
CAP_VS
5
B
VDD
54
MT_GND
6
BLK
17
52
63
HCK1
1
50
62
7
2
D_1.5V
DRUM_ERROR
8
G
D_1.9V
MT_GND
HST HCK2
COM
D_1.9V
61
9
CN63
39P
1
10
VSS
D_2.8V
FP-181
DCG/CLR
VSS
MT_4.9V
S102
EXPOSURE
11
16
D_2.8V
(PANEL REV)
S101
12
EN
15
53
CN1601
L
STB
RGT
51
49
K
EVF_BLEVF_BL+ PANEL_13.3V
29
2
CN3204
PANEL_2.8V
25
41
CONTROL SWITCH BLOCK (CF-30150)
EVF_2.8V
23
1
CN3203
EVF_HCK2
MEMORY DELETE
MEMORY MODEL
J
EVF_GND EVF_VCC
S3215
7P
1
MEMORY MIX
MEMORY+
CN3206 SP901 SPEAKER
I
9 11
MEMORY –
FLEXIBLE
H
CN003
FP-180
S3203
INTELLGENT ACCESSORY SHOE
16P
DATA CODE
LCD BRIGHT-
4-4
MEMORY STICK CONNECTOR
34
6
3
XOSD_SCK
S3210
5
4
XCS_LCD_DRIVER
MEMORY –
HARNESS
5
LCD_COM/XDATA
S3209
4
6
EVER_3.0V SELFTIMER
PC-118
7
PANEL_B S3208
3
LCD
P_UNREG_GND
12P
2
6 5
17
11
N.C.
LCD901
N.C.
9
XHD_OUT
7
N.C.
STBYB
S3206
8
N.C.
4
PANEL_-15.3V
1
9
N.C.
3
16
12
10
N.C.
2
8
CN3201
N.C.
VDD
GSRT
14
BACK-LIGHT
11
VGL
KEY_AD5
1
NR901
12
N.C.
VSS
15
DISP_HD
13
N.C.
1
PANEL_4.6V
(TRV6/6E/20E MODEL)
14
N.C.
VGH
KEY_AD4
PSIG
G
P_UNREG
D_2.8V
MEMORY PLAY
F
4
14
S3205
E
P_UNREG_GND
13
BACK LIGHT
A TO(1/2)
(TRV11/11E/20 MODEL)
PD-123 BOARD PD-124 BOARD
3
12
S3204
D
SEG7
3
SEG3
REG_GND FADER
2
BL_DET
CN2101
15
N.C.
FLEXIBLE
8
GND
PANEL_4.6V
(PANEL CLOSE)
S3202
4
1
PANEL_4.6V
SP-
BL_HI 5P
LCD_PWM
FP-183
4
P_UNREG_GND
15P CN2174
21P
BATT_LI_3V
DISP_HD
INVERTER UNIT
FP-179 FLEXIBLE
C
2
1
2
CN2173 14P 14
SEG2
14P P_UNREG_GND
1
CN3202
SEG1
51P
DIAL_A
MEMORY MODEL : DCR-TRV11/TRV11E/TRV20/TRV20E TRV6 MODEL : DCR-TRV6 TRV6E MODEL : DCR-TRV6E TRV11 MODEL : DCR-TRV11 TRV11E MODEL : DCR-TRV11E TRV20 MDEL : DCR-TRV20 TRV20E MODEL : DCR-TRV20E
FLEXIBLE
CN2175
1
(TRV6/6E/20E MODEL)
COM2
CN3205
B
FP-182
(TRV11/11E/20 MODEL)
COM1
CK-92 BOARD CK-94 BOARD
18
17
LINE IN/OUT MODEL : DCR-TRV6/TRV6E:E,HK,AUS,CN,JE/ TRV11/TRV11E:E,HK,AUS,CN,JE/ TRV20/TRV20E
LCD
A
16
15
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
NS-10 (SUPER NIGHTSHOT SW) PRINTED WIRING BOARD
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
— Ref. No. NS-10 Board; 4,000 Series —
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (Measuring conditions voltage and waveform)
(For printed wiring boards) • b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) • Through hole is omitted. • Circled numbers refer to waveforms. • There are few cases that the part printed on diagram isn’t mounted in this model. • Chip parts. Transistor Diode C
B
E
65 4
45 6
4
12 3
32 1
32 1
5
1
3
2
54 3
2
3
1
2
• Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. * (VOM of DC 10 MΩ input impedance is used.). • Voltage values change depending upon input impedance of VOM used.) * 1. Connection
3
1
2
Pattern Box
1
(For schematic diagrams) • All capacitors are in mF unless otherwise noted. pF : m mF. 50V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10W unless otherwise noted. kW=1000W, MW=1000kW. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520
1.5m
Front of the lens
1-677-555-
Kinds of capacitor Temperature characteristics External dimensions (mm) 2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
White Magenta Red Blue
A=B
For printed wiring board • Refer to page 4-125 for parts location. • This board is four-layer print board. H5owever, the patterns of layers two to four have not been included in the diagram.
B A
LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)
There are few cases that the part printed on this diagram isn’t mounted in this model.
DD-137 (DC/DC CONVERTER)
Fig. a (Video output terminal output waveform) JK-188 (AV IN/OUT)
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Yellow Cyan Green White Magenta Red Blue
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
A B
H
Cyan Green
• Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2 : non flammable resistor • 1 : fusible resistor • C : panel designation • A : B+ Line * • B : B– Line * •J : IN/OUT direction of (+,–) B LINE. * • C : adjustment for repair. * • Circled numbers refer to waveforms. * * Indicated by the color red.
INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
Electron beam scanned frame CRT picture frame
Fig.b (Picture on monitor TV) When indicating parts by reference number, pleas include the board name.
4-5
4-6
SUPER NIGHTSHOT SW NS-10
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
CD-252 (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. CD-252 Board; 4,000 Series —
For printed wiring board • Refer to page 4-125 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. • Chip parts Transistor C
B
E
There are few cases that the part printed on this diagram isn’t mounted in this model. LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER) DD-137 (DC/DC CONVERTER)
JK-188 (AV IN/OUT)
1-677-549-
INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
CCD IMAGER CD-252
4-7
4-8
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
1-677-549-
4-9
4-10
CCD IMAGER CD-252
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E For Schematic Diagram • Refer to page 4-7 for CD-252 printed wiring board. • Refer to page 4-6 for NS-10 printed wiring board. • Refer to page 4-113 for waveforms.
R108
C128 0.1u B
GND R1.7/P0 SHD R1.7/P0 SHP
GND R2.6/P0 CLPDM
CCDout (+)
2
3
GND
CCDout (-)
4
5
CAM_-7V
GND
6
7
CAM_DD_ON
CAM_15V
8
9
PBLK
A_2.8V
10
11
D_3.3V
A_2.8V
12
13
GND
XCAM_RST
14
15
MCK
CS_CAM
16
17
GND
CAM_SO
18
19
CSUB
CAM_SCK
20
21
GND
CAM_SI
22
0.1u B
4
23
TG_HD
TG_ID
24
25
TG_FLD
TG_VD
26
27
ZSG1
ZV1
28
29
GND
FRQ
30
31
S.N.SHOT
GND
32
5
CAM_DD_ON
CCDPBLK
IC104
TG_HD TG_FLD ZSG1
SLOW_SHUT
FOCUS-
39
VM
40
V2
41
V4
42
V1
45
SHT
46 47 48
VSS1
TG_ID
CHCK
TEST
CK
VSS5
OSCO
OSCI 1.3
ID
VDD3
2.6
R1.3/P0
TGVD
TGHD
TGFLD
2.3
R2.6/P0
1.3
0.9
22
PBLK
21
NC
20
VSS4
19 18
16
VL
AVDD2
15
SSO
AVDD1
14
H2
13
33
ZOOM-
ZOOM+
34
35
FOCUS-
FOCUS+
36
37
SLOW_SHUT_GND
IR SW OUT
38
39
F MR A
F MR B
40
41
GND
TEMP OUT
42
43
IRIS DRIVE-
IRIS DRIVE+
44
45
IRIS BIAS+
IRIS_BIAS-
46
47
IRIS HALL+
IRIS HALL-
48
49
MR VCC
Z MR A
50
51
TEMP/MR GND
Z MR B
52
53
ND BIAS+
GND
54
RG
VSS2
4
5
6
7
8
9
10 11 12
CLPDM PBLK
FB104 0uH
ND_HALL55 ND_HALL+ ND_DRIVE+
C126 C127 10u 0.1u B P
ND HALL-
ND BIAS-
TRV20 MODEL :DCR-TRV20 TRV20E MODEL:DCR-TRV20E
TG_ID TG_VD ZV1
ZOOM+
ND_DRIVE-
CN151
FOCUS+
ND_HALL+
NT_SHOT
ND_BIAS+
F_MR_B
ND_HALL-
TEMP I_DRIVE+
CD-252
ND_BIAS-
ND_BIAS+
23
ND_HALL-
22
ND_BIAS-
21
Z_MR_A
20
Z_MR_GND
19
Z_MR_B
18
Z_MR_VCC
17
IRIS_HALL+
16
IRIS_HALL-
15
IRIS_BIAS-
14
IRIS_BIAS+
13
IRIS_DRIVE-
12
IRIS_DRIVE+
11
TEMP OUT
10
TEMP/F MR GND
I_BIAS-
56
57 59
GND
ND HALL+ ND DRIVE+
58
ND DRIVE-
ND_DRIVE-
LENS BLOCK
I_DRIVE-
60 I_DRIVE+
FB105 0uH
TO VC-240 BOARD CN701 TEMP
(SEE PAGE 4-18)
F_MR_B 9
F_MR_B
8
F_MR_A
7
F_MR_VCC
6
IR_SW
5
IR_SW_OUT
4
FOCUS(-)
3
FOCUS(+)
2
ZOOM+
1
ZOOM-
F_MR_A
NT_SHOT FOCUS-
NS-10 BOARD
FOCUS+
XSHD
(TRV20/20E MODEL)
ZOOM+ XSHP L151 10uH
2.6 3.4 H2
R151 XX
ZOOM-
C151 10u 6.3V P
SLOW SHUTTER SW -REF.NO.:4000 SERIESXX MARK:NO MOUNT
C152 1u B CN152
SIGNAL PATH
1
GND
2
GND
3
SLOW_SHUT
4 5
REC
Y
Y/CHROMA
CN152
S001
5P GND
1
GND
2 3
GND
GND
4
GND
GND
5
LENS BLOCK is replaced as a block, so that these PRINTED WIRING BOARD and SCHEMATIC DIAGRAM are omitted.
4-12
5P
SLOW_SHUT
VIDEO SIGNAL
H1
RG
ND_HALL+
24
I_HALL+
PB
4-11
ND_DRIVE-
25
Z_MR_B
16
CCD IMAGER
26
27P
Z_MR_A
Z_MR_A Z_MR_B
ND_DRIVE+
ND_BIAS-
I_BIASI_HALL-
27
I_BIAS+
CHROMA
I
CAM_SI
H1
VSS3
AVDD0
3
C105 0.1u B
CAM_SCK
I_HALL-
R0.9/P0
R1.3/P0
R0.4/P0
TESTEN
3.4
R2.9/P0
2.6
DSGAT
2
CAM_DD_ON
VDD1
2.6
2.3
1 CAM_SCK
H
2.4
CLPDM
XSHP
R1.7/P0
RST
C104 10u 10V A
23
XRS R1.7/P0
SEN
-7.8 CAM_SI
VDD2
17
XCAM_RST
R-7.2/P0
R2.2/P0
24
XSHD
CS_CAM
G
V3
2.6
IC102 CXD2477R-T4
C125 0.1u B
L103 10uH
L104 10uH 3.3V
TIMING GENERATOR
VH
44
C124 10u P
XCHCK
6
IC102
0.2
43 R-0.4/P0
CS_CAM CAM_SO
ND_BIAS+
R2.6/P0
2.5
R-7.0/P0
R2.6/P0
ZSG1 CSUB
R15.0/P0 V3
ZV1
38
R-7.2/P0
V1
R109 0
SSI
37 R2.4/P0
R-0.5/P0
V4
I_BIAS+
SSK
V2
ZV1
I_DRIVE-
R102 82
36 35 34 33 32 31 30 29 28 27 26 25
CAM_SO
0uH FB101
F
nor exposed to strong light. XCAM_RST
SLOW_SHUT
TG_VD
C103 3.3u 20V TA A
In addition, ensure that the receiver is not covered with dusts
ND_DRIVE+
F_MR_A
C112 0.001u B
its structure, handle it carefully like for the MOS IC.
CLPDM
AMP
FB109 0uH
• As the CCD imager may be damaged by static electrictiy from
CCD+
I_HALL+
TG_HD
ZSG1
FB102
E
TG_FLD
0uH
C110 0.001u B
17
adjustments for the camera section.
60P
GND
4
CCD_IN
GND 0.6 OUT2 0.5 OUT1 2.6 VDD
CN101 1
3
2
BYP
ZOOM-
C111 5p CH
X101 66MHz
16
• If the CCD imager has been replaced, carry out all the 1.6
AD80017JSTRL
15k
R107 470k
15
with a CCD imager. When replaching this board, remove the CCD imager from the
2
8 9
B
BYP R0.5/P0 BYP
14 13 12 11 10
B 68p
0.1u
C131
5
VCO
D101 1T379-01-T8A
14
• The CD-252 board mounted as a repair part is not equipped
7
C114
R106 5600
IC103
13
Precautions Upon Replaching CCD imager
6
2.8 OUT
12
C129 10u P
C119
IN-
0.7
11
FB106 CAM_DD_ON 0uH
1
R0/P13.4
2
VCC VSS
3
1
9.8
IN+
C130 0.1u L105 10uH B
3
R113 10k 3.3u A
V1
V2
V3
V4
XSHP
IC103 TA75S01F(TE85R) 0.7
D
XSHD FB103 0uH
Q101 UN9213J-(TX).SO SWITCH
BYP
0.4
FB108 0uH
Q104 UN9213J-(K8).SO
IC104
C118 0.1u
R123 0
1
R8.9/P0 0
2
R104 0
10
old one and mount it onto the new one.
C122 0.1u B R1.3/ P0.1
1.3
R105 4700
C
C113 0.022u B
C109 0.1u B
C116
7
9
2 R2.9/P0
3
0.1u F
6
R112 220k
VDD
RCSUB
VL 5
8
1
Q103,104 CAM DD ON SWITCH
C120
R14.9/ P0
R0/P13.7 R114 1M
5
4
C107 10u 10V A
7
15.0
4
3
C108 0.1u B 1608
R12.4/ P0 R11.7/ P0
2
C106 4.7u 25V TA B BUFFER
GND
Q102 2SC4250(T5LSONY1)
8
CCD IMAGER
1
1
H1 RG
H1
H2
GND
VSUB
9
IC101 V4
R122
B
ICX237AKF-13
0
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
14 13 12 11 10
CCD_OUT
C101 0.1u B
6 Q103 NDS356AP
R15.0/P0
V1
-REF.NO.:5000 SERIESXX MARK:NO MOUNT
V2
CCD IMAGER
5 L101 100uH
V3
(TRV20/20E MODEL)
C132 2200p B
H2
C102 0.1u B
CD-252 BOARD
4
3
3
IC101
A
2 RG
1
SUPER NIGHT SHOT
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
For Schematic Diagram • Refer to page 4-16 for printed wiring board. • Refer to page 4-113 for waveforms.
2
1
3
FP-219 FLEXIBLE BOARD CCD IMAGER
A
4
5
6
7
8
9
10
(TRV6/6E/11/11E MODEL)
R3001 0
CN3001
7
HDR_GND
9
H2
HDR_GND
10
11
H1
HDR_GND
12
13
RG
HDR_GND
14
15
CCD_GND
CCD_GND
16
17
CCD_OUT
CCD_GND
18
7
19
CCD_GND
CCD_GND
20
21
12V
CCD_GND
22
23
S_GND
S_GND
24
25
ZM_XA
ZM_XB
26
27
ZM_A
ZM_B
28
29
GND
NightShot_Vcc
30
31
FC_SENS_OUT
THERMO_OUT
32
33
FC_SENS_Vcc
GND
34
35
FC_XA
FC_XB
36
37
FC_A
FC_B
38
39
ZM_SENS_OUT
GND
40
41
ZM_SENS_Vcc
HALL(+)
42
43
BIAS(+)
HALL(-)
44
45
BIAS(-)
GND
46
47
GND
DRIVE(-)
48
49
DRIVE(+)
SLOW SHUT
50
Q3001 UN9213J-(K8).SO
H2 H1
R11.6/P0
RG
GND
CCD_OUT
9
8
R9.9/P0 RG
H1
H2
R-6.7/ P0.4
C3000 10u 10V TA A
R11.6/P0
H1
10
R9.2/P0
H2
11
0
12
R1.3/P0
13
R6.5/P0
14
D
E
4
SUB
5
VL
6
C3001 10p CH
IC3000
C3003 22u 16V B TA
C3002 0.1u F
R8.4/ P0
IC3000
2
BUFFER
L3000 100uH
Q3000 2SC4178-F13F14-T1
V_HOLD
V_DRAIN
V1
V2
V3
R3.7/P0
R-0.3/P0
R-0.3/P0
R-6.3/P0
R-6.3/P0 V4
3
1
6
6
VSHT
0
5
4
V4
5
RG
4
2
3 R3.7/P0
SWITCH
3
V2 V1 V_DRAIN
V3
C3004 XX B
2
50P
1
VDD
B
1
12
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
-REF.NO.:30000 SERIESXX MARK:NO MOUNT
C
11
R3000 2200
7
TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E
-6.5V
8
TO VC-241 BOARD CN701
CCD IMAGER
(SEE PAGE 4-26) IC3000 ICX220BKC-13 : TRV6/11 MODEL ICX221BKC-13 : TRV6E/11E MODEL
F
Y
Y/CHROMA
13
14
15
16
17
18
19
20
21
22
23
24
FC_XA
GND
FC_SENS_Vcc
THERMO_OUT
FC_SENS_OUT
GND
NightShot_Vcc
ZM_B
ZM_A
ZM_XB
ZM_XA
D3000 MA8082-(K8).S0
12
FC_XB
8
11
7
ZM_SENS_Vcc
FC_A
6
BIAS(+)
FC_B
5
HALL(+)
9
4
BIAS(-)
10
3
HALL(-)
GND
2
GND
ZM_SENS_OUT
1
SUPER NIGHT SHOT
GND
CN3000
VIDEO SIGNAL CHROMA
DRIVE(-)
24P
SIGNAL PATH
G
DRIVE(+)
S3000
LND300
REC PB
LENS BLOCK
LENS BLOCK is replaced as a block, So that these PRINTED WIRING BOARD and SCHEMATIC DIAGRAM are omitted.
H 16
Precautions Upon Replaching CCD imager • The FP-219 flexible board mounted as a repair part is not equipped with a CCD imager. When replaching this board, remove the CCD imager from the old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjustments for the camera section. • As the CCD imager may be damaged by static electrictiy from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strog light.
4-13
4-14
CCD IMAGER FP-219
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
FP-219 FLEXIBLE BOARD (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. FP-219 Flexible Board; 30,000 Series —
FP-219 FLEXIBLE BOARD (SIDE A) (CCD IMAGER) F
50
2 40
30
20
10
CN3001 45
35
25
15
5 1
49
E Q3001 IC3000 1
10
D
1
5
3
2
5
4
R3001
24 5
10
15
C3000
1
6
C3004
C3003
L3000
14
20
CN3000
C3001
8
7
Q3000 R3000
B C E
7
C3002
C For printed wiring board • This board is two-layer print board. However, the patterns of layers two have not been included in the diagram. • Chip parts Transistor C
B
B
E
There are few cases that the part printed on this diagram isn’t mounted in this model. A
K
D3000
FP-219 (TRV6/TRV6E/TRV11/TRV11E) (CCD IMAGER)
A S3000
1-667-566(From LENS BLOCK) (TRV6/TRV6E/TRV11/TRV11E model)
CCD IMAGER FP-219
4-15
16
1
2
3
4
4-16
11
5
Schematic diagram and printed wiring board of the VC-240/241 board are not shown. Pages from 4-17 to 4-74 are not shown.
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
CK-92 (KEY) PRINTED WIRING BOARD — Ref. No. CK-92 Board; 20,000 Series —
For printed wiring board • Refer to page 4-125 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. • Chip parts Transistor
Diode
C
B
3
E
2
1
There are few cases that the part printed on this diagram isn’t mounted in this model. VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O
1-677-556-
MA-385 (AUDIO I/O)
SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)
KEY CK-92
4-75
4-76
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
FP-181 FLEXIBLE BOARD (PANEL REVERSE) PRINTED WIRING BOARD
S906 (PANEL REVERSE)
1-677-563-
11
FP-181 FLEXIBLE BOARD
CONTROL SWITCH BLOCK (PS30150) FP-183 (TRV11/TRV11E/TRV20/TRV20E)
1-677-556-
FP-181 FP-182
4-77
4-78
KEY CK-92
/ PANEL REVERSE FP-181
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
CK-94 (KEY) PRINTED WIRING BOARD — Ref. No. CK-94 Board; 30,000 Series —
For printed wiring board • Refer to page 4-125 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. • Chip parts Transistor
Diode
C
B
3
E
2
1
There are few cases that the part printed on this diagram isn’t mounted in this model. VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O
1-677-559-
MA-385 (AUDIO I/O)
SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)
KEY CK-94
4-79
4-80
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
1-677-559-
4-81
4-82
KEY CK-94
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
For Schematic Diagram • Refer to page 4-75,79 for printed wiring board.
2
1 CK-92 BOARD CK-94 BOARD A
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
(TRV11/11E/20 MODEL) CN3201
(TRV6/6E/20E MODEL)
KEY -REF.NO.:30000 SERIESXX MARK:NO MOUNT
(TRV11/11E/20 MODEL) TO PD-123 BOARD CN2176
1
51
OSD_SO
XOSD_SCK
2
50
XOSD_SCK
3
49
XCS_LCD_DRIVER
LCD_COM/XDATA
4
48
LCD_COM/XDATA
EVER_3.0V
5
47
EVER_3.0V
PANEL_B
6
46
REG_GND
PANEL_G
7
45
PANEL_B
PANEL_R
8
44
REG_GND
PANEL_VG
9
43
PANEL_G
PANEL_COM
10
42
REG_GND
XHD_OUT
11
41
PANEL_R
PSIG
12
40
REG_GND
39
PANEL_VG
TO PD-124 BOARD CN3171
(SEE PAGE 4-97)
B
OSD_SO
XCS_LCD_DRIVER
(SEE PAGE 4-93)
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
CN3205
12P
51P
(TRV6/6E/20E MODEL)
CN3202
C
TO PD-123 BOARD CN2173
(SEE PAGE 4-93) S104
S105
LCD BRIGHT-
LCD BRIGHT+
38
REG_GND
37
PANEL_COM
36
C-SYNC/XHD
35
XVD
34
REG_GND
DISP_HD
1
DISP_VD
2
GND
3
GND
4
PANEL_2.8V
5
33
(TRV11/11E/20 MODEL)
CONTROL SWITCH BLOCK (CF-30150) S106
14P
C3203 10u 25V TA C
MEMORY MODEL
REG_GND
PANEL_13.3V
6
32
REG_GND
PANEL_-15.3V
7
31
HI_SO
PANEL_4.6V
8
30
XHI_SCK
S103
VOLUME-
VOLUME+
TO PD-124 BOARD CN3202
HI_SO
9
29
XCS_LCD
XHI_SCK
10
28
P_UNREG
TO VC-240 BOARD CN003
XCS_LCD_DAC
11
27
P_UNREG
(SEE PAGE 4-62)
(SEE PAGE 4-97)
D
(TRV6/6E/20E MODEL) R106 3300
R104 1200
R105 1500
R103 10k
P_UNREG
12
26
XHD_OUT
P_UNREG_GND
13
25
PSIG
P_UNREG_GND
14
24
P_UNREG_GND
23
P_UNREG_GND
C3201 10u 16V TA B
S100
S102 SEL/PUSH EXEC
PROGRAM AE R3201 0 1/10W
S101
E
EXPOSURE
R102 1500
R101 1200
CN3203 R100 10k
7P
PANEL_2.8V
19
KEY_AD7
D_2.8V
7
18
PANEL_13.3V
KEY_AD7
KEY_AD7
6
17
KEY_AD6
KEY_AD3
KEY_AD3
5
16
PANEL_-15.3V
4
DIAL_B
DIAL_B
4
15
KEY_AD5
3
DIAL_A
DIAL_A
3
14
PANEL_4.6V
2
GND
GND
2
13
KEY_AD4
1
GND
GND
1
12
D_2.8V
11
KEY_AD3
CN100
7P
10
G S97
D3203 01ZA8.2(TPL3)
(PANEL_REV)
6P
CN3204
D3201 01ZA8.2(TPL3)
R3202 22k
R3208 3300
R3205 6800
R3211 1500
R3214 1200
D3202 01ZA8.2(TPL3)
KEY_AD6
BT3201 BATTERY
6P
6
GND
GND
1
5
GND
GND
2
4
PANEL_REV
KEY_AD4X
3
3
PANEL_REV
KEY_AD4X
4
2
GND
GND
5
1
GND
GND
6
S3201
S3203
S3206
S3209
(PANEL_CLOSE)
MEMORY INDEX
MEMORY+
MEMORY-
R3203 22k
R3206 6800
R3209 3300
S3212
S3215
MEMORY MIX
R3212 1500
MEMORY DELETE
R3215 1200
REG_GND
9
REG_GND
8
REG_GND
7
REG_GND
6
SP+
5
REG_GND
4
SP-
3
DIAL_B
2
BATT_LI_3V
1
DIAL_A
2
SP-
1
SP+
MEMORY MODEL
KEY_AD5 CN3206
D3204 01ZA8.2(TPL3)
FP-181 FLEXIBLE
MEMORY MODEL:DCR-TRV11/TRV11E/ TRV20/TRV20E
LND321
S3202
S3204
S3207
S3210
S3213
GND
FADER
BACK LIGHT
DIGITAL EFFECT
TITLE
PB ZOOM
R3204 22k
R3207 6800
R3213 1500
R3210 3300
S3216 MENU R3216 1200
KEY_AD4
LND322 GND R3217 1k
I LND323
16
GND S3205 MEMORY PLAY
S3208 SELFTIMER
S3211
S3214
S3217
S3218
END SEARCH
DATA CODE
DISPLAY
RESET
MEMORY MODEL
KEY
20
D_2.8V
CN96
CK-92/94
XRESET_SW
5
CONTROL SWITCH BLOCK(CF-30150)is replaced as a block. So that this PRINTED WIRING BOARD is omitted.
H
P_UNREG_GND
21
6
GND
TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL :DCR-TRV20 TRV20E MODEL:DCR-TRV20E
22
7
LND100
F
C3202 XX 16V TA G
4-83
4-84
2P SP901 SPEAKER
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
LB-64 (EVF BACK LIGHT) PRINTED WIRING BOARD — Ref. No. LB-64 Board; 10,000 Series —
2
1
4
3
5
6
7
LB-64 BOARD EVF BACK LIGHT
A
-REF.NO.:10000 SERIESXX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE CN2201
CN2202
27P COM
1
1
COM
G
2
2
G
R
3
3
R
B
4
4
B
BLK
5
5
BLK
HCK1
6
6
HCK1
HCK2
7
7
HCK2
HST
8
8
HST
B
RGT TO DD-137 BOARD CN1604
9
9
DCG/CLR
10
10
DCG/CLR
EN
11
11
EN
STB
12
12
STB
VCK2
13
13
VCK2
(SEE PAGE 4-110)
VST
14
14
VST
VSS
15
15
VSS
VSS
16
16
VDD
VDD
17
EVF_BL_GND
18
EVF_BL_GND
19
EVF_BL_4.6V
20
BUFFER
EVF_BL_4.6V
21
IC2201 TC7SET08FU(TE85R)
N.C
26
N.C
27
E
4.6
25
C2204 2200p B
5
24
PWM
10
L2202 10uH 2
VCC
0.4
0.5
LED_K
1
L2201 47uH 3225
R2205 10k
0.5
C2201 0.1u B
3
4.5
4
23
4.6
22
1
N.C DET
T2201 INVERTER TRANS
IC2201
2
D
LCD903 EVF LCD
RGT
THROUGH THE FP-180 FLEXIBLE BOARD
3
C
16P
4
5
6
ND2201 BACKLIGHT
Q2201 FX216-TL1 SWITCHING C2202 33u 10V TA B
LND201
C2203 4.7u B
A
F
LND202 A
R2204 XX
R2203 82
1-677-553-
D2202 XX
R2202 XX
G
For printed wiring board • Refer to page 4-126 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram.
LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER)
H
NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)
There are few cases that the part printed on this diagram isn’t mounted in this model.
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
16 DD-137 (DC/DC CONVERTER)
JK-188 (AV IN/OUT)
INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
4-85
4-86
EVF BACK LIGHT LB-64
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
JK-188 (A/V IN/OUT) PRINTED WIRING BOARD — Ref. No. JK-188 Board; 10,000 Series —
1-677-552-
For printed wiring board • Refer to page 4-126 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram.
LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)
There are few cases that the part printed on this diagram isn’t mounted in this model.
DD-137 (DC/DC CONVERTER)
JK-188 (AV IN/OUT)
INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
A/V IN/OUT JK-188
4-87
4-88
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
2
1
3
5
6
7
8
9
10
11
12
13
14
A/V IN/OUT -REF.NO.:10000 SERIESXX MARK:NO MOUNT
C
J3001
Y S
D3001 015AZ8.2-TPL3
3
4
S
2
R3056 10k
R3061 0
2
1.6
47
46
HP_L
44
DV_GND
42
TPA
40
NTPA
38
DV_GND
36
XSJACK_IN
34
S_Y_GND
AM2
OUT2
C_RESET
VCC 2.8
Vref2
0.1
HO2
1.5
HI2 C3061 10u
1.4
LO2
1.4
53
49
LIA2
1.4
GND
XHP_JACK_IN
LIB2
1.5
GND
XAVJACKIN
20
1.5
55
54
48
19
1.0
57
GND
51
18
R3060 1k
C3062 10u
R3057 1M
SIGNAL PATH
R3002 0
R3003 0
VDR005
VDR006
LND033 GND
HP_R
45
4
DV_GND
43
3
TPB
41
2
NTPB
39
1
TPA NTPA
IC3051
DV_GND
37
S_Y_OUT
35
GND
33
LND033
TPB NTPB J3004
4P
GND
32
S_C_GND
S_C_OUT
31
30
KEY_AD2
GND
29
28
LANC_DC
GND
27
26
LANCK_SIG/232C_RD
GND
25
24
XLANC_JACK_IN
LANC_GND/232C_TD
23
VTR_UNREG
21
IR_DRV
19
22
VTR_UNREG
20
GND
18
IR_EM
16
GND
14
XF_TALLY_LED
12
MF_LED
10
MF_B
GND
17
XSIRCS_IN
15
A_4.6v
13
MF_A
11
AU_2.8V
8
ZOOM_MIC_CONT
6
XMIC_MONO
9
EXT_MIC_DET
7
SHOE_MIC_L
5
4
AU_GND
MIC_L
3
2
AU_GND
MIC_R
1
J3003 FB3004 0uH
AUDIO/VIDEO VDR001
FB3005 0uH VDR002
R3004 0 VDR007 FB3007 0uH
J3002
HEADPHONE
FB3008 0uH VDR003 1000p
R3005 0
VDR004 1000p
LND031 GND
VIDEO SIGNAL CHROMA
PS_OUT
C_RST
L_IO
17
E
F
YS_OUT
56
V_IO
16
R3055 10k
58
GND
15
C3059 0.047u B
59
R_IO
14
R3054 22k
G
G
DV IN/OUT
3 R3051 22k
A_2.8V
50
13
C3057 0.047u B
C3055 0.1u B
A_2.8V
52
12
0.8
4
60
1
2
11
C3051 XX
SE3052 (YAW)
3
IC3051 UPC6756GR-8JG-E2
C3054 22u A
1
L3052 10uH
PASS
C3052 XX P
D
1.4 4
S VIDEO
R3001 0
C3067 0.1u B
R3059 1M
OUT1
5
C3066 22u A
R3058 15k
AM1
6
1.4
1.4
1.5 7
Vref1
LIB1
8
HO1
9
GND
10
HI1
C3053 22u A
1.0
R1.8/P0.8
C3056 0.1u B
R0/P1.5
C3064 10u
R3053 22k
C3065 0.33u B
C3063 10u
C3060 0.047u B
LO1
R3052 22k
B
C3058 0.047u B
LIA1
1
SE3051 (PITCH)
C
15
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
JK-188 BOARD A
4
Y
Y/CHROMA
CN3001
AUDIO SIGNAL
LND032
60P
TO VC-240 BOARD CN001
GND
(SEE PAGE 4-65)
REC PB
G
H
28
KEY_AD2
27
LANC_DC
26
LANC_SIG
25
LANC_JACK_IN
24
232C_TO
23
GND
22
VTR_UNREG
21
VTR_UNREG
20
GND
19
IR_DRV
18
IR_EM
17
GND
16
GND
15
XSIRCS_IN
14
XF_TALLY_LED
13
A_4.6V
12
MF_LED
11
MF_A
10
I 16
4-90
(SEE PAGE 4-106)
MF_B
9
AU_2.8V
8
ZOOM_MIC_CONT
7
EXT_MIC_DET
6
XMIC_MONO
5
SHOE_MIC_L
4
AU_GND
3
MIC_L
2
AU_GND
1
MIC_R CN3002
4-89
TO MA-385 BOARD CN2071
28P
A/V IN/OUT JK-188
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
PD-123 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD — Ref. No. PD-123 Board; 20,000 Series — 3
4
5
6
7
8
CONTROL SWITCH BLOCK (FK-30150)
A CN008
B
CN062
39P N.C.
39
SHOE_UNREG
38
SHOE_UNREG
37
SHOE_UNREG
1
LANC_SIG
36
LANC_SIG
2
SHO_ID1
35
CN63
SHO_ID1
3
SHO_ID2
34
SHO_ID2
4
33
SHOE_MIC_R
5
MIC_GND
32
MIC_GND
6
31
SHOE_GND
30
SHOE_GND
29
MS_VCC
28
INS
27
BS
26
GND
25
8
N.C.
7
STATICS_GND
6
VSS
5
BS
4
DIO
3
INS
2
SCLK
1
VCC
8P
10
CN51
11
FP-183 FLEXIBLE
8P N.C
8
STATICS_GND
7
VSS
6
1
VSS
BS
5
2
BS
DIO
CN52
INTELLGENT ACCESSORY SHOE
4
3
VCC
INS
3
4
DIO
SCLK
2
5
N.C
VCC
1
6
INS
7
TO VC-240 BOARD CN008
(SEE PAGE 4-65)
D
DIO
24
SCLK
23
GND
22
XEJECT_SW
21
IR_LED_VCC
20
N.C
8
SCLK
9
VCC
10
VSS
IR_LED_ON
19
KEY_AD_0
18
MT_4.75V
17
FK_LED_ON
16
MT_4.75V
15
KEY_AD_1
14
GND
13
XMS_ACCSEE
12
MS_LED_VCC
11
XPHOTO_FREEZE
10
R073 150
S61 EJECT
R063 1200 S062
IR_LED
S069
GND
9
ZOOM_AD
8
D_2.8V
7
D64
R072 470
D66
S066
FF
S068
D62
D65
PAUSE
R068 1500
S067
R067 3300
S072
S71
R069 6800
PHOTO (FREEZE)
LINE IN/OUT MODEL 30150
F
D63
R071 150
(MS ACCESS) REC
E
R070 150
MEMORY MODEL
(SWITCH BACK LIGHT)
S065
PLAY
R074 1200
D70
D69
R066 6800
S064
REW
S070 D73
R065 3300
R064 1500 S063
STOP
MS_ACCSEE
MEMORY STICK CONNECTOR
8
SHOE_GND
D72
10P
7
SHOE_MIC_L
LINE IN/OUT MODEL
C
12
8P
SHOE_MIC_R
SHOE_MIC_L
9
ENDSERCH -
ENDSERCH +
IR_ON
(PHOTO REC)
R085 0
RV61
MEMORY MODEL
CONTROL SWITCH BLOCK (PS-30150)
GND
6
XPHOTO_STBY_SW
5
XS/S_SW
4
XVTR_MODE_SW
3
N.C.
2
1
XPHOTO_STBY_SW
XCAM_STBY_SW
1
2
XCAM_STBY_SW
CN064
6P
3
GND
4
XVTR_MODE_SW
5
XS/S_SW
N.C.
6
XS/S_SW
5
XVTR_MODE_SW
4
START/STOP
S1
S2
POWER
S/S
VTR
1-677-557-
2
1
(VTR) GND
3
XCAM_STBY_SW
2
XPHOTO_STBY_SW
1
RV61
OFF (CAM)
6 ZOOM
CAMERA (PHOTO) PHOTO
T
G
W
CONTROL SWITCH BLOCK(FK-30150,PS-30150) is replaced as a block.so that this PRINTED WIRING BOARD is omitted. MEMORY MODEL :DCR-TRV11/TRV11E/TRV20/TRV20E LINE IN/OUT MODEL:DCR-TRV6/TRV6E:E,HK,AUS,CN,JE,/TRV11/ TRV11E:E,HK,AUS,CN,JE/TRV20/TRV20E
16
For printed wiring board • Refer to page 4-126 for parts location. • This board is four-layer print board. However, the patterns of layers two to four have not been included in the diagram. • Chip parts
LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER) DD-137 (DC/DC CONVERTER)
Transistor C
B
E
JK-188 (AV IN/OUT)
PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
There are few cases that the part printed on this diagram isn’t mounted in this model.
CONTROL SWITCH BLOCK FK-30150
/ LCD DRIVE, RGB DRIVE PD-123
INVERTER TRANSFORMER UNIT
4-92
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
For Schematic Diagram • Refer to page 4-113 for waveform.
2
3
PD-123 BOARD(1/2)
4
5
6
8
9
(TRV11/11E/20 MODEL) SEG11
SEG12
SEG13
SEG14
COM2 SEG2 SEG3
1.5
1.5
1.5
SEG15
1.5
SEG16
1.5
1.5
-REF.NO.:20000 SERIESXX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE
SEG4 SEG5
SEG11
SEG12
SEG13
SEG14
SEG15
SEG17
SEG18
32 31 30 29 28 27 26 25
SEG6 SEG7
1
B
OSC1
2
2.0 3 4
3.0 3.0 6
LCD DRIVE
VLCD
IC2171 BU9735K-E2
SEG5
7
SEG4
8
SEG3 SO
1.5 1.5 1.5 1.5 1.5 1.5 1.5
SEG10
VG
10
COM_OUT
XHD_OUT
11
XHD_OUT
PSIG
12
PANEL_VG
CN2173
2
TO(2/2)
14P DISP_HD
1
SYNC
DISP_VD
2
XVD
REG_GND
3
REG_GND
4
TO(2/2) C2174 10u 6.3V
SEG9
SEG10
SEG8
SEG11
SEG7
SEG12
SEG6
SEG13
SEG5
SEG14
SEG4
SEG1
SEG3
SEG16
SEG2
4
SEG3
5
SEG4
6
SEG5
7
SEG6
8
SEG7
9
SEG8
10
SEG9
11
SEG10
12
SEG11
13
SEG15
CHARACTER DISPLAY
SEG12
14
SEG13
15
SEG14
16
SEG1
17
SEG16
18
COM4
SEG2
SEG1
COM2
3
SEG15
19
COM3
20
COM4
21
N.C
1.5
1.5
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Q2173 2SB1462J-QR(K8).SO BACK LIGHT SWITCH 4.5 0
L2173 100uH
3
2
13
21P
SEG2
TO(2/2)
COM1
2.9
9
PANEL_COM
1
SEG1
PANEL_R
COM4
8
1.5
PANEL_G
PANEL_R
COM4
PANEL_B
7
COM3
6
PANEL_G
1.5
5
PANEL_B
COM1
12
10 11 12 13 14 15 16
COM3
EVER_3.0V
9
COM2
4
COM1
LCD_COM/XDATA
1.5
3
COM2
XCS
2
C/XD
XOSD_SCK
0
1
1.5
OSD_SO
1
11
LCD902
SEG9
COM3
XCS_LCD_DRIVER
E
SEG6
1.5
12P
(SEE PAGE 4-83)
D
SEG7
VC
SCK
0.1
TO CK-92 BOARD CN3201
SEG8
VDD
2.8
CN2176
SEG9
IC2171
VSS
3.0
C
1
OSC2
5
C2180 0.01u B
SEG10
17 18 19 20 21 22 23 24
SEG8 R2180 680k 1.5
10 CN2175
COM1
LCD DRIVE
A
7
SEG16
1
C2175 0.1u B
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
R2175 4700 3.7 R2176 1k BL
TO CK-92 BOARD CN3202
(SEE PAGE 4-83)
F
PANEL_2.8V
5
PANEL_2.8V
PANEL_13.3V
6
PANEL_13.3V
PANEL_-15.3V
7
PANEL_-15.3V
PANEL_4.6V
8
PANEL_4.6V
HI_SO
9
XHI_SCK
10
XCS_LCD_DAC
11
P_UNREG
12
P_UNREG_GND
13
P_UNREG_GND
14
0
2.7
(STARTER) 13P
REG_GND
XHI_SCK
4
5
BACK LIGHT SWITCH
TO(2/2)
TO(2/2)
L2172 4.7uH C2172 47u 16V
HI_SO
7
Q2172 UN9214J-(K8).SO
6
C2182 XX C2173 0.1u B
R2177 0
1
BL_GND
BL_DET
2
LED
PWM
3
BL_LOW
4
NC
5
NC
6
NC
7
NC
8
NC
5P
CN2174 1
PWM
2
PANEL_4.6V
3
BL_DET
4
P_UNREG_GND
5
P_UNREG
5P PWM PANEL_4.6V
5 4
BL_DET
3
P_UNREG_GND
2
P_UNREG
1
TO(2/2)
XCS_PANEL
R2178 XX
LND217 A
G
TO(2/2)
SIGNAL PATH
INVERTER UINT
9
NC
10
NC
11
NC
12
NC
13
BL_HI
ND901 BACK LIGHT
VIDEO SIGNAL CHROMA
Y
Y/CHROMA
REC PB
H 16
TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL :DCR-TRV20
4-93
4-94
LCD DRIVE PD-123 (1/2)
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
For Schematic Diagram • Refer to page 4-92 for printed wiring board. • Refer to page 4-114 for waveforms.
2
PD-123 BOARD(2/2)
5
6
7
L2103
L2104
0
6.7
COM_OUT
24 23 22 21 20 19 18
C2122 6.8u 16V TA A
17
N.C
4.5 13.5
C2124 0.1u B
C2125 1u 3216 B
C2123 0.1u B
*
R2140
4
5
6
7 0
3
L2102 10uH
8
9
10
*
D2103
11
TG24
12
TG23 TG22
R2113 2700 R2116 68k
C2114 0.1u B
R2114 47k
TG21
R2120 100k R2119 1M
C2108 10u 6.3V TA
* R2122
N.C
2
1
D2102 1T369-01-T8A
C2113 560p CH
R2117 22k
G
R2118 68k
TG19 TG12
* C2118
R2126
TG16 TG15 TG14 TG13 XP.SAVE
* C2127 25V TA *
*
XC.SAVE
XHI_SCK
C2128 R2111 0.1u B Q2107 100k 1608 2SD2216J-QR(K8).SO
6
XCS_PANEL
RGB DRIVE PD-123 (2/2)
XHD_OUT
VG
19
VR
18
HCNT
17
MCLK
16
CLR
15
OE
14
SRT
13
STBYB
12
VBC
11
VCOM
10
RESET
9
STBYB
8
GSRT
7
GPCK
6
GRES
5
N.C.
4
VDD
3
VGL
2
VSS
1
VGH
LCD901
*
*MARKED:MOUNT TABLE TRV11/11E MODEL
Q2102 *
6
7
8
9
10
11
12
XX
0.01u 16V B
XX
C2131
0.01u 16V B
XX
C2132
C2118
82p 16V CH
56p 16V CH
D2103
MA111-TX 871940450
XX
L2105
3.3uH ± 5%
2.2uH ± 5%
IC2105
LZ9FF424
CM7019L2-T
IC2106
TC7SET04FU
XX
Q2102
MGSF1P02LT
XX
Q2103
2S81462J-Q
XX
Q2104
2SD2216J-Q
XX
Q2105
2S81462J-Q
XX
Q2106
2SD2216J-Q
XX
R2101
XX
0
R2103
0
XX 56k
* *
*
5
1 2
R2125 0uH
0
TG23
4
C2131 B
IC2106
* Q2105 R2145 XX
TG22 *
2.6
Q2106
R2150
TG21
0
C2132 B
*
DR.P.SAVE CPMODE/CLS
5
1u 25V
TG24 R2127 120
3
OSCI
OSCO
4
1.3
(Note)
*
XC.SAVE
3
TRV20 MODEL
C2127
*
PD
2
R2147
R2151
TG20 * R2103
2.7
TG19
0
TG18
2.7
TG17
0
TG16
0.1
TG15
2.5
TG14
0.5
TG13
* R2149
R2141 10k
BL_DET
Q2108 UN9213J-(K8).SO
7 PWM
TO(1/2)
BL
SIGNAL PATH
R2123
VIDEO SIGNAL CHROMA
TG12
Y
R2122
XX
R2123
XX
0
R2124
0
XX
R2126
Y/CHROMA
16
4-96
XX
0
R2140
XX
0
R2143
180k
XX
R2144
PB
4-95
VB
20
* Q2104
REC
XCS_PANEL
TO(1/2)
M
2.5
2.7
L
SYNC
1.4
*
PS/VDD
TESTI
HI_SO
24
GND
TESTI
XVD
HI_SO
23
-IN/TESTO
PWM
XVD
2.7
TO(1/2)
2.7
8
SYNC
22
+IN/TESTO
1
XHD_OUT XHD_OUT
CP/SPS
21
OUT/TESTO
9
16
LED
XVD
GPCK/MODE1 GRES/EX1
2.7
VSYB
20
37 38 39 40 41
10
SI
TESTI/GND
2.6
STBYB/SPG GSRT/MODE2
GND/TESTI
1.1
SO
BL-DET
HI_SO
XCS
RESET/EX2
BL-ON
2.6
11
W/H
XTG_SO
VDD/RES
* IC2105
VDD/TESTI
MCLK/CLD
SRT/PSS1
TIMIING GENERATOR
XSCK
HCNT/SPD
OE/PSS2
12
IC2105
R2101
14
CLR/CTR
HDB
3.0
K
SYNC
VSS
21
IC2106
19
25
18
26
17
27
16
28
15
29
14
30
HDI
XCS_PANEL
COM_FRP
42
2.4 2.7
3
22
R2148
13
31
13
FRP
43
1.3
44
1.3
XVD
2.7
32
SW
45
FRP COM_FRP
SWCOM
46
0.1
XHI_SCK
0
33
15
BGP
47
0
48
J
1.4
34
13.5
35
I
BLK
0
0
2.7
36
R2142 470k
BGP
1.4
C2109 0.1u
SYF
2.7
POCB
0
0
D2101 MA111-TX
C2130 1u B 3216
* R2144
R2146
Q2103
*
H
VDD
TG17
* R2121
TO(1/2)
VSH
23
TG18
* L2105
XHI_SCK
24
LCD
TG20
C2117 1000p SL
* R2124
C2110 0.1u B
TO(1/2)
R2129 10k
C2121 1u B 2012
16
43
1.7
2
CN2101
N.C
4
VR
13
R_IN
C2133 XX CH
2.2
VG
C2120 1u B 2012
VG
14
3
1.7
15
Vcc4
G_IN
2.2
C2119 1u B 2012
VB
N.C
COM_OUT
B_IN
1.7
N.C
0.01u
C2135 XX CH
VSH
VCO
C2107
PANEL_R
1.8
2
XP.SAVE
VB
2.2
0
0.01u
GND1
OP_OUT
C2106
LPF_ADJ 2.7
OP_IN-
0
PANEL_G
GND2
0
R2152
1.7
TRAP_ADJ 1.1
OP_IN+
0.01u
VR
R_DC_DET
IC2104 RB5P003AM1
0
C2105
5
RGB DRIVE
Vcc1 1.1
BIAS
0
XCS
VG
G_DC_DET
0
R2154
1.7
46
XP.SAVE
0
47
C2101 C2102 68u 0.1u 4V TA B
R2153 PANEL_B
48
C2134 XX CH
C2104 XX R2109 R2107 27k XX ± 0.5%
IC2104
SI
N.C
38 39 42
R2108 0 XX C2103 XX R2106 33k ± 0.5%
6
N.C
L2101 10uH
VB
B_DC_DET
XSCK
N.C
0
XC.SAVE
N.C
XCS_PANEL
7
EXT_DA2
N.C
0
40
XTG_SO
41
2.4
44
D
XHI_SCK
45
R2105 470k
0
37
1.6 XC.SAVE
VG
FRP
COM_FRP
25
100
GND3
26
R2135
27
VR
28
100
29
100
30
R2133
31
R2134
32
13.5 Vcc3
33
Vcc2
FRP
COM_FRP
34
BLACK_IN
0
1.3
BLK
35
N.C
0
0.1
36
* R2143
5
18
C2115 0.1u B
C2112 0.1u B 1608
BGP
0
C2111 3.3u 20V TA
EXT_DA1
0
BGP
C2129 0.01u B
R_INJECT
C
F
17
16
C2116 10u 10V TA A R2112 15k
TO(1/2)
15
14
10uH
PANEL_2.8V
1
13
10uH
PANEL_4.6V
REG_GND
E
12
TRV11 MODEL :DCR-TRV11 TRV11E MODEL :DCR-TRV11E TRV20 MODEL :DCR-TRV20
PANEL_13.3V
B
11
(Note) Inductor is mounted to the location where R2125 is printed.
PANEL_-15.3V
TO(1/2)
10
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
-REF.NO.:20000 SERIESXX MARK:NO MOUNT
4
9
8
(TRV11/11E/20 MODEL)
RGB DRIVE
A
4
3
*
1
XX
0
R2146
XX
0
R2147
10k
XX
R2148
47k
XX
R2149
XX
0
R2150
1M
XX
R2151
1M
XX
R2121
1M
XX
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
For Schematic Diagram • Refer to page 4-101 for printed wiring board. • Refer to page 4-114 for waveform.
SEG16
(TRV6/6E/20E MODEL)
LCD DRIVE -REF.NO.:30000 SERIESXX MARK:NO MOUNT
8
9
10
11
1.5
1.5
1.5
1.5
1.5
1.5
SEG11
SEG12
SEG13
SEG4
SEG14
SEG3
SEG16
2
COM2
3
SEG2
4
SEG3
5
SEG4
6
SEG5
7
SEG6
8
SEG7
9
SEG8
10
SEG9
SEG5 SEG6
3
2
1.9
3.0
4
C3171 0.01u B
5
3.0
6
3.0
7
2.9 0.1
8
C
SEG10
OSC1 SEG9 OSC2
IC3171
VSS
SEG8 SEG7
VC SEG6
IC3171 BU9735K-E2
VLCD
SEG5
VDD SEG4 SCK SEG3 SO
1.5 1.5 1.5 1.5 1.5 1.5 1.5
SEG10
SEG7
SEG9
SEG8
SEG8
SEG9 SEG10
SEG7
SEG11
SEG6
SEG12
SEG5
SEG13
SEG4 SEG3
1.5
SEG16
SEG2
SEG1
COM4
COM3
COM2
XCS
2
COM1
XOSD_SCK
1
SEG10
12
SEG11
13
SEG12
14
SEG13
15
SEG14
16
SEG1
17
SEG16
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
LCD XXX
SEG1
SEG15 OSD_SO
11
14
SEG14
12P
C/XD
CN3171
1
1.5
1
R3174 680k
17 18 19 20 21 22 23 24
B
13
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
SEG2
32 31 30 29 28 27 26 25
SEG17
COM1
COM2
SEG18
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
1
12
21P
CN3173 COM1
SEG15
A
7
SEG11
6
SEG12
5
SEG13
PD-124 BOARD(1/2)
4
SEG14
3
SEG15
2
1
18
SEG15
COM3 19
COM3
20
COM4
21
N.C
COM4
PANEL_R
2.9
9
VG
PANEL_COM
10
COM_OUT
XHD_OUT
11
PSIG
12
PANEL_VG
TO(2/2)
2
TO(2/2)
3
TO(2/2)
1
SYNC
DISP_VD
2
XVD
REG_GND
3
REG_GND
REG_GND
4
R3175 4700
4
TO(2/2)
5
TO(2/2)
4.6
4.6
14P DISP_HD
Q3172 2SB1462J-QR(K8).SO
L3172 100uH
PSIG XHD_OUT
CN3172
E
1
1.5
8
SEG2
PANEL_R
1.5
PANEL_G
SEG1
PANEL_B
7
1.5
6
PANEL_G
COM4
PANEL_B
(SEE PAGE 4-83)
COM1
D
1.5
5
COM3
EVER_3.0V
10 11 12 13 14 15 16
1.5
TO CK-94 BOARD CN3201
9
COM2
4
0
3
LCD_COM/XDATA
1.5
XCS_LCD_DRIVER
3.8 R3176 1k
(STARTER) BL
TO CK-94 BOARD CN3202
(SEE PAGE 4-83)
F
G 16
PANEL_2.8V
5
PANEL_2.8V
PANEL_13.3V
6
PANEL_13.3V
PANEL_-15.3V
7
PANEL_4.6V
8
HI_SO
9
6
C3175 10u 6.3V
TO(2/2)
C3176 0.1u B
2.8
R3171 0 R3172 0
L3171 4.7uH
HI_SO
7
C3177 XX
R3178 XX
CN3174
2
PANEL_4.6V
3
BL_DET
13
4
P_UNREG_GND
14
5
P_UNREG
XCS_LCD_DAC
11
P_UNREG
12
P_UNREG_GND P_UNREG_GND
R3173 0
XHI_SCK
TO(2/2)
XCS_PANEL
C3173 47u 16V
C3174 0.1u B
TO(2/2)
R3177 0 PWM
10
9
BL_DET A Q3171 UN9214J-(K8).SO
13P TO(2/2)
LND311
TA P
1
XHI_SCK
8
PWM
0
5P
4-97
BL_GND
2
LED
3
BL_LOW
4
NC
5
NC
6
NC
7
NC
8
NC
9
NC
10
NC
11
NC
12
NC
13
BL_HI
5P PWM PANEL_4.6V
1 2
BL_DET
3
P_UNREG_GND
4
P_UNREG
5
INVERTER UINT
TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV20E MODEL:DCR-TRV20E
1
ND901 BACK LIGHT
4-98
LCD DRIVE PD-124 (1/2)
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
For Schematic Diagram • Refer to page 4-114 for waveforms.
2
1
3
PD-124 BOARD(2/2)
4
(TRV6/6E/20E MODEL)
6
7
8
9
10
11
12
13
14
15
16
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
LCD DRIVE
A
5
-REF.NO.:30000 SERIESXX MARK:NO MOUNT L3101 10uH
13.5
Q3103 NDS356AP
13.5
PANEL_13.3V
C3116 0.01u B
24 23 22 21 20 18
19
C3121 1u
R3160 100k
C3104 10u 6.3V TA P
C3113 1000p SL
* R3115 XX
13.5
* L3104
32
31
30
29
28
27
26
25
SHB 0.9
SHA 0.9
GND
TESTI/VDD
RPD 1.4
XCSAVE 2.8
OSCI 1.4
OSCO 1.4
XSTBY 2.8
POFF
10
NC
1
2
SYNC
2.8
3
4
5
6
7
8
9
10
11
24 23 22 21 20 19 18 17 16 15
RGT
14
SI
XVD
0
9
CRext
TG16
8
HCK2
7
HCK1
6
PSIG
5
G
4
R
3
B
2
* R3143 R3157 100k
RGT
1
TEST2 CN3101
24P
Q3105 XP4601-TXE
PWM
TG24
8 TO(1/2)
BL
3 TO(1/2)
XHD_OUT
2.2 TG22 2.8 TG21 0.1 TG20
SIGNAL PATH *MARKED:MOUNT TABLE
VIDEO SIGNAL
2.8 0
CHROMA
TG18
1.4 TG17
REC
1.4 TG16
PB
Y
2.8 TG15 2.8
TG14
TRV20E MODEL
TRV6/6E MODEL
C3117
39p 16V CH
47p 16V CH XX
C3129
1u 10V B XX
1u 10V B
Y/CHROMA
C3132
TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV20E MODEL:DCR-TRV20E
D3103
RD2.7UM-T1
XX
D3104
XX
RD3.3UM-T1
L3104
2.2uH ± 5%
3.3uH ± 5%
R3137
56k
XX
R3143
0
XX
R3144
XX
0
R3146
110k
XX
12
R3139 6.8k
Q3108 UN9213J-(TX).SO
4-99
TEST
TG17
1.4 TG23
16
PD-124 (2/2)
10
LCD
R3133 10k
M
RGB DRIVE
REF
6.1
C3126 0.1u B
0.1
BL_DET
HST
11
6.1
13
HCK1
2.6
L
HCK2
SO
VDO
12
Q3106 XP4601-TXE
TEST/GSPB
8
XCS
TEST/GPWCB
4 TO(1/2)
HST
IC3102 CXD3505R-T4
TEST/GPWC
2.8
VDD
PWM
47 48
XVD
VDD
LED
K
2.5
IC3102
XSCK
WIDE
6.7
6.7
2.8
2.7 46
HI_SO
WIDE
TESTI/GND
3.0 45
XTG_SO
PFRP
GND
2.8 44
XCS_PANEL
DWN
2.8
42 43
2.6
EN
FRP
DETIN
1.4 XHI_SCK
SBLK
BL
41
J
1.4
VCK
2.8
PFRP
PRG
XWRT
0 40
FRP
13
Q3104 2SB1462J-QR(K8).SO
VST
9
HDO
2.8 39
BLK
XCLP
0.3
PRG
CS
TG18
TG14
33
SHG 2.8
XP.SAVE
XC.SAVE
34
SHR 0.9
SH4
SH3
35
XCLR 2.8
SH2
36
HD
37 2.7
XCS_PANEL
XCS_PANEL
9 TO(1/2)
R3128 100k
BGP
XHI_SCK
38
XHI_SCK
14
1.7 1.1
SH1 HI_SO HI_SO
7 TO(1/2)
VSSG
TG20
13.5
6.7 * C3117 CH
D3101 MA111-TX
I
VDDG
15
* D3104
C3130 0.1u
7.3
R3127 220k
H
VSS/GND
16
TG15
D3102 1T369-01-T8A
C3131 0.1u B
VDD
17
R3159 R3158 100k 100k
2.8
R3107 470k
DWN
18
B
R3113 100k
0
EN
19
R
R3132 10k
R3131 100k
R3116 1M
C3112 R3114 68k 560p CH
R3135 100k
C3111 0.1u B
C3106 0.1u B
20
G
R3118 ± 0.5% XX B
C3122 XX F
2.3
Q3107 2SD2216J-QR(K8).SO
VCK
TG21
LCD901
R3120 XX ± 0.5%
R
3.2
R3117 0
6.7
L3103 10uH
21
* D3103
R3134 150k
G
G
VST
TG22
6.4
C3115 0.1u
R3112 22k
COM
TG23
22
* R3144
* C3132
R3136 0
VG
VB
VR
VP R3124 100
R3123 10
C3123 XX F
R3109 0
R3110 47k
TEST1
23
* C3129
12
R3111 68k
C3128 4.7u
24 TG24
* R3137 R3119 XX
R3121 10
0 COM_IN
* R3146
R3122 10
16 15
17
D3105 MA111-TX
COM_DC
11 1.5
10
VCO
OP_OUT
OP_IN9 1.4
8 1.4
7 1.4
6
OP_IN+
BIAS
N.C
SH_A 5 0.9
0.9
4
SH2
2.8
3
SH1
F
SH_B
XSH.SAVE
2
1
2 TO(1/2)
PSIG COM_OUT
R3138 XX
1.7 Vcc2
1.4 XVP.SAVE
2.8 VP
FRP
PFRP
2.8 FRP
1.4 PFRP
BLK
0 PRG
N.C
EXT_DA
13.5 0 COM_OUT
14
42 43 45
C3135 CH 120p
C3134 CH 120p
13.5 Vcc3
4
VG
C3120 1u VR
6.7 VREF
3
R_IN
1.8 C3133 CH 120p
2
0.9
100
PANEL_R
GND1
G_IN
1.8 48
R3142
1.8
C3110 0.01u B
LPF_ADJ
SH4
PANEL_G
GND2
C3119 1u VG
6.7 VR 1.7 R_DC_DET
IC3101 RB5P004AM1
2.8
E
C3108 0.01u B
5
TRAP_ADJ
B_IN
R3126 0
VB
1.7 G_DC_DET
XP.SAVE
2.8
C3109 0.01u B
IC3101
SH3
1 TO(1/2)
100
1.1 XP.SAVE
6.7
6.7 VG
6
Vcc1
44
100
PANEL_B R3141
1.1
0
Q3102 UN9213J-(TX).SO
VB 1.7 B_DC_DET
SH_R
R3140
2.8
C3107 0.01u B
0
25
26
NEW-DRIVER
46
REG_GND
R3104 XX
R3105 33k ± 0.5%
5 TO(1/2)
C3103 XX SL
R3102 33k ± 0.5%
C3102 0.1u B
C3101 68u 4V B
27
7
XCS
3.0
PANEL_2.8V
28
2.7 SI
47
D
R3101 XX
C3127 0.01u B
R3125 470k
2.8
29
13
37 XCS_PANEL L3102 10uH
30
2.6 XSCK
40
XTG_SO
31
C3125 XX B
VP
N.C 2.8 XC.SAVE
39
XHI_SCK
32
C3114 1u B
1.1
38
XC.SAVE
41
R3106 470k
33
BGP 2.7 BLACK_IN
C3105 0.01u B REG_GND
34
SH_G
6 TO(1/2)
C
35
R_INJECT 0.7
36
PRG
BGP
R3108 15k
6.7 P_DC_DET
B
C3124 XX 20V TA A
C3118 3.3u 20V TA A
4-100
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
SE-107 (MANUAL FOCUS) PRINTED WIRING BOARD
— Ref. No. PD-124 Board; 30,000 Series —
— Ref. No. SE-107 Board; 4,000 Series —
1-677-554-
PD-124 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD
1-677-560-
For printed wiring board • Refer to page 4-126 for parts location. • This board is four-layer print board. However, the patterns of layers two to four have not been included in the diagram. • Chip parts
For printed wiring board • Refer to page 4-127 for parts location. • This board is four-layer print board. However, the patterns of layers two to four have not been included in the diagram.
There are few cases that the part printed on this diagram isn’t mounted in this model.
LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER)
VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O
MA-385 (AUDIO I/O)
NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)
SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)
DD-137 (DC/DC CONVERTER)
Transistor C
B
E
JK-188 (AV IN/OUT)
INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
There are few cases that the part printed on this diagram isn’t mounted in this model.
4-101
4-102
LCD DRIVE, RGB DRIVE PD-124
/ MANUAL FOCUS SE-107
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
MA-385 (AUDIO I/O) PRINTED WIRING BOARD — Ref. No. MA-385 Board; 10,000 Series —
I/O LANC
1-677-551-
For printed wiring board • Refer to page 4-127 for parts location. • This board is four-layer print board. However, the patterns of layers two and three have not been included in the diagram. • Chip parts Transistor
VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O
Diode
C
3 MA-385 (AUDIO I/O)
B
E
2
1
There are few cases that the part printed on this diagram isn’t mounted in this model.
AUDIO I/O MA-385
4-103
4-104
SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
7
8
9 C2045 0.1u B
MA-385 BOARD
F
R2020 22k
R2017 2.2k
1k B
R2016
1.5
1.5
1.5
1.5
1.5
1.5
C2024
0.1
1.5
R_OUT
7
8
9
C2016 XX
HPF_AMP_IN_R
6
4
1.5
MIC_L
1.5
XMIC_MONO
2.7 R2032
2.8
R2033
1.5 2.8 2.7
C2037 10u C2036 0.1u B
0.1
6.3V
ZOOM_MIC_CONT
1200 33k
D2061 TLSU1002(TPX1,SONY)
TA P C2038 0.22u F
R2034 18k
R2061 XX
(TALLY) EXT_MIC_DET
1.9
R2065 470
1.5 R2031 33k
L2001 10uH 2520
MIC_R
R2029 XX
C2034 XX B
ZOOM_MIC_CONT EXT_MIC_DET
C2030 XX B
XMIC_MONO SHOE_MIC_L
100p
CH C2020 0.1u R2022 22k
C2025 0.068u B 1608
MIC_L
C2026 0.022u B 1608
MIC_R
R2028 22k R2025 0 R2026 27k
4
IC2091
C2032 0.015u B
KEY_AD2
27
LANC_DC
26
LANC_SIG
25
LANC_JACK_IN
24
232C_TD
23
GND
22
VTR_UNREG
21
VTR_UNREG
20
GND
19
IR_DRV
18
IR_EM
17
GND
16
GND
15
XSIRCS_IN
TO JK-188 BOARD CN3002
14
XF_TALLY_LED
(SEE PAGE 4-90)
13
A_4.6V
12
MF_LED
11
MF_A
10
MF_B
9
AU_2.8V
8
ZOOM_MIC_CONT
7
EXT_MIC_DET
6
XMIC_MONO
5
SHOE_MIC_L
4
AU_GND
3
MIC_L
2
AU_GND
1
MIC_R
5
MF_LED_B
MF_LED_B
5
4
MF_LED_A
MF_LED_A
4
SE-107 BOARD MF SENSOR CN2051
-REF.NO.:4000 SERIESXX MARK:NO MOUNT
5P
3 C2091 10u 6.3V TA
IC2091 RS-70-TU
REMOTE COMMANDER RECEIVER
28P
28
R2051 220
R2091 47
4.5
C2031 0.0033u B
R2052 220
GND
3
MF_B
MF_B
2
MF_A
MF_A
1
3
GND
2 1
2
4.4
1
R2035 0
D2091 MA2S111-(K8).SO
H C2072 10u 16V TA B
SIGNAL PATH VIDEO SIGNAL CHROMA
Y
Y/CHROMA
AUDIO SIGNAL
D2072 DCR2815
REC
Q2071 2SD999-T1-CLCK
D2071 DAC3825
16
LASER LINK
4-105
R2071 18 1/16W
R2072 10 1/10W 2012
PH082 GP1S93
Q2074 2SB1462J-QR(TX).SO
R2073 47k 7.9
0.1 0.1
C2071 0.1u B
PB
R0.1/ P0.3
8.0
8.0 7.9
PH081 GP1S93
R2075 6.8 1/16W 1608
Q2072 2SB624-T1BV4 0.5 8.0
I
D2063 MAZJ200D0LS0
CN2071
C2039 22u 4V TA
10 11 12
C2022 0.1u B
R2018 2.2k
C2042 0.001u B
NC
1.5
5
3
HPF_OUT_R
2
1.5
1
SUB_IN_R
MTX_AMP_OUT_R
MTX_AMP_IN_R
C_1/2VCC
13 14 15 16 17 18 19 20 21 22 23 24
HPF_ON/OFF
GND
R2014 6800
A
R2030 XX
HPF_OUT_L
MTX_AMP_OUT_L
MTX_AMP_IN_L
SUB_SIG_OUT_L
SG_IN_L
INVT_OUT_L
EXT_MIC
MIX_OUT
1.5
D2001 01ZA8.2(TPL3)
D2002 01ZA8.2(TPL3)
VCC
IC2002 AN2901FHQ-EB
C2013 100p CH
MODE_CTL_2 1.5 AMP_OUT_L
ZOOM_POSI
C2009 0.0047u B C2011 0.001u B
ZOOM_BAL
NC
C2005 0.022u B
G C2043 2200p B
INFINITY
R2064 820
HPF_AMP_IN_L
R2021 9.1k
LND001
MAN
R2063 22k
manual Focus
MIC AMP
C2017
C2041 0.001u B
C2035 XX B
C2033 XX B
ZOOM_AMP_IN
1.5
1.5
J2001 MIC (PLUG IN POWER)
FOCUS AUTO
MIC_MONO
1.5
1.5
FB2003 0uH
C2027 0.022u B 1608
IC2002
ZOOM_AMP_OUT
SUB_SIG_OUT_R
1.5
FB2002 0uH
DIGITAL I/O
J2002
LANC
L_OUT
INVT_OUT_R
C2008 0.01u B R2010 10k
FB2001 0uH
17
S2061 R2039 XX
NC
1.5
1.5
E
FB2061 0
(Note)
R2027 22k
GND NC
SG_IN_R
1.5
C_REG
1.5
R2009 4700
1.3
48 47 46 45 44 43 42 41 40 39 38 37
C2010 10u 6.3V P
C2012 10u 6.3V P
16
36 35 34 33 32 31 30 29 28 27 26 25
C
D
C2046 0.1u B
0.1u
C2007 0.022u B
AMP_OUT_R
4
2.4
3
INT MIC GND
REG_2.5V
2
INT MIC R
1k
INT MIC GND
R2015
MIC
1.5 SUB_IN_L R0/P1.5 INT_IN_L
R-CH
1
C2047 0.1u B
R2062 12k
REG_2.5V R0/P1.5 EXT_IN_R 2.2 MODE_CTL_1
MIC
INT MIC L
C2015 0.001u B
INT_IN_R
L-CH
4P
C2014 100p CH
XX
2.4
CN2001
C2006 0.0047u B
C2019
EXT_IN_L
B
100p CH
C2018
R2012 2200
15
R2036 11k ± 0.5%
C2044 0.1u B
R2038 5600 ± 0.5%
R2019 9.1k
14
(Note) Resistor is mounted the rocation where FB2061 is printed.
VDR201
C2021 0.1u B
R2011 2200
1.5
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
13
SHOE_MIC_L
R2037 11k ± 0.5% 1005
C2029 0.0033u B
R2024 0
12
0uH
C2023 0.068u B 1608
R2013 6800
MIC901 MIC UNIT
C2028 0.015u B
R2023 27k
11
D2062 01ZA8.2(TPL3)
R2008 33k
-REF.NO.:10000 SERIESXX MARK:NO MOUNT
1.5
R2007 18k
MIC AMP
A
10
0uH
6
FB2062
5
FB2063
4
0uH
3
FB2064
2
1
R2074 1k 7.9
Q2073 UN9211J-(TX).SO 0.1 0.1
C2073 0.1u B
4-106
AUDIO I/O MA-385
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
For Schematic Diagram • Refer to page 4-111 for printed wiring board. • Refer to page 4-115 for waveforms. 2 3 1 DD-137 BOARD(1/2) A
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
DC/DC CONVERTER -REF.NO.:10000 SERIESXX MARK:NO MOUNT
BATT/XEXT_SW BATT_SIG
F1605 1.4A 1608
D1602 01ZA8.2(TPL3)
R1604 10 1/8W 3216
3P
BATT_UNREG
R1608 XX 3216
1
BATT_SIG
2
BATT_GND
3
Q1602 SI4963DY-T1 SWITCH 4
C
VTR_UNREG
LF1601 1-411-957-21
D
LND161
A
LND162
A
3
7.9
7.7
6 5 7 8
1
7.7
2
D1601 MA8120-TX
R1602 470k
7.5
7.5 7.5
CAP_ERROR
F1604 1.4A 1608
R1605 1k
2
F1603 1.4A 1608
CAP_VS
F1602 1.4A 1608
D1609 1SS388(TPL3)
0.1
0.8
7.9
C1608 10u 16V TA B
R1606 4700 0
C1616 22u 16V TA B
D1607 RB501V-40TE-17
4
3
Q1603,1604 CHARGE ON SWITCH
R1603 1M
VCC(C)
DRUM_ERROR
6
C1624 4.7u 6.3V B 2012
7
R1641 1k 7.9
VDD C1622 1u B 10V 2012
0.2
R1642 1k
7.9
SI2304DS-T1
2.5
C1626 1u B 10V 2012
Q1612 CPH6702-TL
0
C1635 4.7u 10V B 3216
2.8
C1603 0.022u B
J
3.0 0 0
C1615 0.001u B
0.2
0.3
0.5
11.8 OUT7-2
VCC(O) 5678
-IN8
out8
7.9
6.6 FB8
6.6
2.5
0.7 ROFS
DTC 8
COMP
+IN8
2.5
2.5
1.3
1.2 -IN7
+IN7
FB7
RB8
VDD(O) 567
6
-IN5
OUT5-2 out5-1
7
IC1601 MB4488PFV-BND-G-ER-F
FB5
VSS(O) 567
DTC 56
out4
8
GND
VCC(O) 1234
9
VREF
out3-2
VCC
out3-1
10
CTL1-6,8 CTL7
GND(O) 1234 out2-2
11
CS1-7
out2-1 VDD(O) 123
CSCP
RT
VB
C1604 0.022u B
2.7 Q1623 SI2304DS-T1
10.0
Q1617 2SB1462J-QR(K8).SO 5.0
R1645 47k 6.8
R1637 100
3.0
Q1615 2SD2216J-QR(K8).SO
R1638 100
11.3
2.4 2.4
4.9
R1646 10k
C1629 3300p B
2.9
R1678 1200 ± 0.5%
5.0
2.9
3.9
Q1624 2SD2216J-QR(K8).SO
6.6
R1639 100
9.8
7.9
C1631 3300p B
0.1 T1602
11.8 C1630 3300p B
3.3
4
C1632 3300p B
2.7
3 CH-4
R1640 100
4.9
6
0.1 Q1608 MCH6103-TL SWITCHING 7
2
C1638 0.01u B 1608 25V
R1616 10k ± 0.5%
D1612 1SS388(TPL3)
1.6
8.7
6.6
C1671 R1651 XX 0 13.3V C1649 2.2u 16V 2012 F C1647 2.2u 16V 2012 F
TRV6/6E/11/11E MODEL
PANEL_13.3V
C1650 0.1u 50V 2012 F
D
13
12
D1613 1SS388(TPL3)
C1627 3300p B
8
1
D1610 1SS388(TPL3)
C TRV20/20E MODEL
E
14
C1625 2200p B
C1620 220p B R1626 33k
Q1609 CPH6702-TL 4.7 L1603 22uH CHOKE
R1634 3900 ± 0.5% C1633 4.7u 10V B 3216
R1635 3900 ± 0.5% R1636 ± 0.5%
R1636 10k :TRV20/20E MODEL 15k :TRV6/6E/11/11E MODEL
4.7 1.6 7.9 9.0
R1631 ± 0.5%
R1633 3300 ± 0.5%
*
1.4
1.3
1.3 C1618 470p B R1623 22k
1.2
R1627 22k ± 0.5% R1622 R1624 47k 47k ± 0.5% ± 0.5%
R1681 XX 15V/13.3V
C1646 2.2u F 16V 2012
9.8
R1628 56k ± 0.5%
47k R1612 22k ± 0.5%
M
TO(2/2)
R1679 0
D1611 MA796-TX 5
R1644 100
10.4
R1630 22k ± 0.5%
R1620
C1607 0.1u 10V B
3
R1648 33k ± 0.5%
R1643 100
10.3
R1629 56k ± 0.5%
Drum servo (speed and phase)
C1639 10u 10V TA A
220 R1632
PB
Capstan servo (speed and phase)
Q1615-1617 Q1624 +4.9V REG
R1647 22k ± 0.5%
7.3
9.9
*
REC/PB
1.2 C1617 2200p B R1621 10k
R1615 10k
REC
1.3
2.5
1.6
1.3
1.3 B
0.5
0.5
C1612 2200p
2.0
C1609 100p CH
SIGNAL PATH
L
A
MT_4.9V
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
K
Q1614 Q1623 SWITCHING
MT_4.9V 8.0
9.8
3.0 * R1609 0
out6-1
DC/DC CONVETER
2.8V C1644 4.7u 6.3V B 2012
CHOKE
7.8
C1628 3300p B
OUT6-2
5
IC1601
-IN5(C) +IN5
2.8V L1606 22uH
2.9
Q1616 2SB1581-T1
TRV11/11E/20/20E MODEL
3 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
7.9 C1602 0.1u B
4
out1-2
2.5
2.9
B
2
OUT7-1
-IN6 FB6
Q1622 SI2304DS-T1
10.5
Q1613 Q1622 SWITCHING
2.8 1
out1-1
TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL :DCR-TRV20 TRV20E MODEL:DCR-TRV20E
2.5
C1674 0.01u B
2
VSS(O) 1234
1.2 R1702 1k
3
FB1
I
4
-IN1
0.9
5
-IN2
0.9
6
FB2
1.8
7
FB3
1.1
-IN3
0.3
8
GND(O) 5678
DTC 123
R1699 22k
9
1
DTC4
R1700 22k
3.3
Q1614 CPH6702-TL
-IN6(C)
-IN4
R1701 22k
1.9V C1643 4.7u 6.3V B 2012
CHOKE
7.9
C1637 4.7u 10V B 3216
+IN6
FB4
0.3
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
0.5 C1605 2200p B R1610 4700
DTC 7
OVP 56
R1696 47k
H
CT
R1697 22k
16 15 14 13 12 11 10
TRV11/11E/20/20E MODEL
D_1.9V L1605 22uH
2.0
CH-2
2.5
2.5 R1695 270k
2.0
Q1612 Q1621 SWITCHING
C1621 100p CH
C1619 0.001u B
C1611 470p B
C1642 4.7u 6.3V B 2012
Q1621 SI2304DS-T1
10.1
CH-3
-IN8’
G
3.1V
L1604 22uH CHOKE
7.9 CH-7
C1636 4.7u 10V B 3216
R1614 22k
3.1V
3.2 3.2
Q1607 UN9213J-(K8).SO
R1619 3300 ± 0.5%
R1611 22k
Q1611 Q1620 SWITCHING
Q1620
10.2
CH-5
Q1613 CPH6702-TL
TRV11/11E/20/20E MODEL
C1641 4.7u 6.3V B 2012
CHOKE
2.9
Q1606,1607 PROTECT DETECT
R1625 10k
L1602 33uH
2.7
8CH
R1617 68k ± 0.5%
DRUM VS
2.7
9.2
0
D1608 VSS RB501V-40TE-17
D1606 RB501V-40TE-17
R1613 47k ± 0.5%
Q1619 SI2304DS-T1
8
1
F
CHOKE
11.3
Q1611 CPH6702-TL
DRUM_VS
C1640 4.7u 6.3V B 2012
7.9 CH-6
C1623 4.7u 6.3V B 2012
7.8
Q1605 MCH6202-TL SWITCHING
R1698 22k
CAP VS
3.9
5
TRV11/11E/20/20E MODEL
C1606 XX B 2012
3.0
C1614 22u 16V TA B
C1613 10u 16V TA B
C1610 10u 16V TA B
T1601
C1634 4.7u 10V B 3216
Q1618 SI2304DS-T1
4.6V C1645 4.7u 6.3V B 2012
CH-1 Q1609,1618 SWITCHING
R1631 82k :TRV6/6E/11/11E MODEL 100k :TRV20/20E MODEL
R1618 27k
16
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
DC/DC CONVERTER DD-137 (1/2)
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
4-107
TO(2/2)
L1601 22uH
0.8
Q1601 SSM3K03FE(TPL3) SWITCH
E
Q1610 Q1619 SWITCHING
F1601 1.4A 1608
2 C1601 0.022u B 16V
Q1610 CPH6702-TL
7.9
Q1606 2SB1462J-QR(K8).SO
3
7.3
2
F1606 1.4A 1608
Q1603 2SB1122-ST-TD
ACV_GND BATT_XEXT
R1607 XX 3216
Q1604 UN9213J-(K8).SO
1
CN1602
TO(2/2)
BATT_UNREG
ACV_UNREG
D1604 1SS388(TPL3)
J902 DC IN
J901 BATTERY TERMINAL
INIT_CHARGE_ON
3P
CN1601
B
1
FAST_CHARGE
R1601 1k
VTR_DD_ON REG_GND
4-108
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
For Schematic Diagram • Refer to page 4-111 for printed wiring board. 2 3 1
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
DD-137 BOARD(2/2) DC/DC CONVERTER
A
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
-REF.NO.:10000 SERIESXX MARK:NO MOUNT
TRV6 MODEL :DCR-TRV6 TRV6E MODEL :DCR-TRV6E TRV11 MODEL :DCR-TRV11 TRV11E MODEL:DCR-TRV11E TRV20 MODEL :DCR-TRV20 TRV20E MODEL:DCR-TRV20E
CAP_ERROR
2 TO(1/2)
B
CAP_VS DRUM_ERROR DRUM_VS C1670 XX B 2012
Q1627 2SA2018-H-T2L
C
1.5 C1660 10u 6.3V A
2.0
R1652 100k
IC1602 4.7
0.7 IC1602 TA75S01F(TE85R)
R1657 33k ± 0.5%
DIGITAL 3.1V ANALOG 3.1V
3.1V
L1608 1uH 3225
D 1.9V
1.3 5
4
+
–
0.7
1
2
C1665 XX B
3
0.1
* L1607 3225
Q1628 2SD2216J-QR(K8).SO
1.3
ERROR AMP
* L1619
D1615 MA3XD21001S0
COM G R B BLK
*
*
1.5 C1658 6.3V A
C1652 6.3V A
1.5
C1651 10u :TRV6/6E/11/11E MODEL 47u:TRV11/11E MODEL
C1651 6.3V A
R1656 22k
R1658 110k ± 0.5%
C1663 0.1u B
HCK1 R1655 470
HCK2 HST RGT
L1610 1uH 3225 L1612 4.7uH L1611 1uH 3225
E
ANALOG 2.8V
DCG/CLR
AUDIO 2.8V
EN
DIGITAL 2.8V
STB VCK2
2.8V
Q1639 2SD2216J-QR(K8).SO -7.7
R4.5/ P-1.8
R1654 22k
R-9.1/ P-9.6
*
R1690 ± 0.5%
* Q1647
* Q1653
* R1676
-7.7
DET
± 0.5% 0.1
0.5 R1666 22k
* R1680 R1677 220k ± 0.5%
0.5
* Q1649
C1669 B
C1672 4.7u 25V TA B
R1691 ± 0.5%
LED_K PWM
R1689 ± 0.5%
R1686
*
2.5
B
Q1635 2SB1462J-QR(K8).SO
Q1629 UN9213J-(K8).SO
R1653 47k
C1666 10u 20V B TA
*
A
Q1650
R1684
R1675 100k ± 0.5%
R-9.1/ P-9.6
R1662 100k
*
R9.7/P-10.2
G
* L1624 *
C1654 10u :TRV20/20E MODEL 22u:TRV6/6E/11/11E MODEL
F
VST
C1659 47u 6.3V B
C1656 10u 6.3V A
C1654 6.3V A
*
C1653 10u 6.3V A
*
L1609 4.7uH 3225
27P
CN1604 Q1627 Q1628 +1.5G REG
27
COM
26
G
25
R
24
B
23
BLK
22
HCK1
21
HCK2
20
HST
19
RGT
18
DCG/CLR
17
EN
16
STB
TO LB-64 BOARD CN2201 THROUGH THE FP-180 FLEXIBLE BOARD
15
VCK2
14
VST
13
VSS
12
VSS
11
VDD
10
EVF_BL_GND
9
EVF_BL_GND
8
EVF_BL_4.6V
7
EVF_BL_4.6V
6
N.C(XTALLY_LED)
5
DET
4
LED_K
3
PWM
2
N.C
1
N.C
(SEE PAGE 4-86)
Q1643 2SB1462J-QR(K8).SO
C
*MARKED:MOUNT TABLE TRV20/20E MODEL
TRV11/11E MODEL
C1652
10u 6.3V
10u 6.3V
XX
C1658
10u 6.3V
10u 6.3V
XX
C1669
XX
0.1u 10V B
0.1u 10V B
L1607
1uH ± 20%
1uH ± 20%
XX
L1619
4.7uH ± 20%
4.7uH ± 20%
XX
L1624
4.7uH ± 20%
XX
XX
Q1646
UN9213J
XX
XX
Q1647
XX
2SD2216J
2SD2216J
Q1648
UN9213J
XX
XX
Q1649
XX
2SD2216J
2SD2216J
MT_4.9V R1669 0
* R1692
Q1637 2SD2216J-QR(K8).SO
* R1683
D
R-27.8/P-23.4 R-27.8/P-23.4
-16.0
R1672 47k ± 0.5%
Q1632,1637 Q1641 -15.3VG REG
TO(1/2)
0.5 R1664 22k
R1674 100k ± 0.5%
*
*
* R1685 C1667 2.2u F 2012 16V
VST
* Q1648
INV.
L1618 22uH
Q1625,1626 SHOE ON SWITCH 7.9
INV.
L1617 22uH 3225
R1649 10k
Q1626 MGSF3455VT1 0
C1648 1u 10V B 2012
R1663 XX
Q1634 XX
C1655 2.2u 16V F 2012
R1682 1k
R1665 XX D1616 MA2S111-(K8).SO
0.1
R1667 XX ± 0.5% C1668 2.2u F 16V 2012
R1670 XX ± 0.5%
EVF_STB
EVF_G
4
EVF_VCK2
EVF_R
6
7
EVF_VST
EVF_B
8
3 5
9
EVF_GND
EVF_BLK
10
11
EVF_VCC
EVF_HCK1
12
13
EVF_DET
EVF_HCK2
14
15
EVF_LED_K
EVF_HST
16
17
EVF_PWM
EVF_RGT
18
19
EVF_13.3V
EVF_DCG/CLR
20
21
EVF_2.8V
EVF_BL-
22
PANEL_-15.3V
27
SHOE_ON
4.6V
EVF_BL+
24
PANEL_13.3V
26
PANEL_4.6V
28
SHOE_GND
SHOE_UNEREG
30
31
SHOE_GND
SHOE_UNEREG
32
33
REG_GND
CAM_-7.5V
34
COM G R B BLK HCK1 HCK2 HST RGT DCG/CLR
35
REG_GND
CAM_15V
36
37
REG_GND
D_3.1V
38
39
REG_GND
D_3.1V
40
A_3.1V
RP_4.6V AU_4.6V
A_4.6V
44
45
A_2.8V
A_4.6V
46
47
A_2.8V
AU_2.8V
48
43
A_4.6V
49
D_2.8V
D_1.9V
50
51
D_2.8V
D_1.9V
52
53
MT_4.9V
D_1.5V
54
55
MT_4.9V
D_1.5V
56
57
MT_4.9V
DRUM_VS
58
59
MT_GND
DRUM_VS
60
61
MT_GND
DRUM_ERROR
62
63
MT_GND
CAP_VS
64
65
VTR_DD_ON
CAP_VS
66
67
CAM_DD_ON
CAP_ERROR
68
69
INIT_CHARGE_ON
VTR_UNREG
70
71
FAST_CHARGE
VTR_UNREG
72
73
BATT_SIG
VTR_UNREG
74
75
BATT/XEXT_SW
BATT_UNREG
76
77
P_UNREG_GND
P_UNREG
78
79
P_UNREG_GND
P_UNREG
80
AU_4.6V R1693 1 2012
EVF_BL_4.6V
L
1 C1657 10u 10V TA A
C1661 10u 10V TA A
C1664 10u 10V TA A
XX
2S81462J
2S81462J
Q1653
XX
2SD2216J
2SD2216J
R1609
0
0
XX
R1631
100k
82k
82k
R1636
10k
15k
15k
C1662 10u 10V TA A
R1694 2012 C1673 10u 10V TA A
VTR_DD_ON
XX
0
0
R1669
0
XX
XX
R1676
10k
22k
18k
47k
R1680
XX
R1683
820
XX
XX
R1684
XX
100k
100k
R1685
22k
XX
XX
R1686
XX
22k
22k
R1687
1800
XX
XX
R1688
1800
XX
R1689
XX
18k
18k
R1690
XX
100k
100k
R1691
XX
47k
47k
R1692
820
XX
XX
42
RP_4.6V
L1614 1uH 2520
Q1650
R1668
L1615 1uH 2520 L1616 1uH 2520
PANEL_2.8V
25
41
L1613 4.7uH
M
PWM
2
EVF_EN
29
R1671 XX ± 0.5%
D1614 MA2S111-(K8).SO
Q1625 UN9213J-(K8).SO 7.9
R1650 1M
4.6V
DET
80P EVF_COM
1
23 Q1636 XX
7.7
K
STB VCK2
Q1633 XX
J
R15.2/P0.1
R3.0/ P0.1
LED_K
PANEL_13.3V
E
CN1603
R1688 EN
R0/ P2.1
R0/P2.1
* Q1646
Q1641 2SB1462J-QR(K8).SO
3
I
R0/ P0.1
-0.2
Q1632 2SB1462J-QR(K8).SO
R1687
R1668
*
H
R1673 270k ± 0.5%
-16.0
R-28.3/ P-23.9
R1661 100k
TRV6/6E MODEL
47k
XX
REG GND
REG_GND INIT_CHARGE_ON
1 TO(1/2)
SIGNAL PATH
TO VC-240 BOARD CN002
FAST_CHARGE
(SEE PAGE 4-66)
BATT_SIG
REC
BATT/XEXT_SW BATT_UNREG
REC/PB
PB
Drum servo (speed and phase)
VTR_UNREG
N
Capstan servo (speed and phase) 16
4-109
4-110
DC/DC CONVERTER DD-137 (2/2)
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
DD-137 (DC/DC CONVERTER) PRINTED WIRING BOARD — Ref. No. DD-137 Board; 10,000 Series —
1-677-550-
For printed wiring board • Refer to page 4-127 for parts location. • This board is four-layer print board. However, the patterns of layers two to four have not been included in the diagram. • Chip parts
LB-64 (EVF BACK LIGHT) CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER) DD-137 (DC/DC CONVERTER)
Transistor C
B
E
65 4
45 6
12 3
32 1
JK-188 (AV IN/OUT)
PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
There are few cases that the part printed on this diagram isn’t mounted in this model.
DC/DC CONVERTER DD-137
4-111
INVERTER TRANSFORMER UNIT
4-112
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
4-3. WAVEFORMS
PD-123 BOARD (1/2)
FP-219 BOARD
CD-252 BOARD CAMERA REC
REC/PB
1 IC3000 1
1 IC2171 2
1 Q102 E 7.5Vp-p 64 µsec
3.0Vp-p 1.0Vp-p
38.5 µsec
43.3 µsec
2 IC3000 2 2 IC104 qa 19.8Vp-p 1.0Vp-p
20 msec
43.3 µsec
3 IC3000 3,4 3 IC104 qd 7.3Vp-p
64 µsec 3.6Vp-p 30 nsec
4 IC3000 0 4 IC104 qf
3.5Vp-p 55.5 nsec 3.6Vp-p 30 nsec
5 IC3000 qa,qs
5 IC104 5
900mVp-p 43.3 µsec
3.3Vp-p 55.5 nsec
6 IC3000 qd 6 IC102 wl 16.4Vp-p 64 µsec 3.1Vp-p 15 nsec
7 Q3000 E
0.8Vp-p 64 µsec
4-113
WAVEFORMS CD-252, FP-219, PD-123
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
PD-123 BOARD (2/2)
PD-124 BOARD (1/2)
REC/PB
REC/PB
2 IC2104 rh
0 IC2105 qg
1 IC3171 2
3.1Vp-p 500mVp-p H
3 IC2104 rj
3.0Vp-p
H
38.5 µsec
qa IC2105 qk
3.0Vp-p 440mVp-p
V
H
PD-124 BOARD (2/2) REC/PB
4 IC2104 rk
2 IC3101 rh
qs IC2105 wa
420mVp-p H
3.0Vp-p
7 IC3101 wf
500mVp-p
H
H
8.0Vp-p 2H
5 IC2104 w;
3 IC3101 rj
qd IC2105 wd
3.0Vp-p
4.0Vp-p
440mVp-p
90 nsec 2H
8 IC3102 1
H
H
3.5Vp-p
6 IC2104 ws
4 IC3101 rk
qf IC2105 wf
2.8Vp-p 3.5Vp-p
9 IC3102 wh
420mVp-p
127 µsec
3.0Vp-p
H 55 nsec
2H
7 IC2104 wf
5 IC3101 w;
qg IC2105 wh
0 IC3102 rk
3.0Vp-p V
3.2Vp-p 2H
8 IC2105 1
8.0Vp-p
45 nsec
3.5Vp-p
2H
6 IC3101 ws
qh IC2105 rk
3.0Vp-p
3.0Vp-p V
H
8.0Vp-p 2H
9 IC2105 qf
3.2Vp-p H
WAVEFORMS PD-123, PD-124
4-114
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
DD-137 BOARD (1/2) REC/PB
1 IC1601 3
8 IC1601 th
5.1Vp-p 1.3Vp-p 2.4 µsec
2 IC1601 1
2.4 µsec
9 IC1601 tf
5.0Vp-p 2.5 µsec
5.0Vp-p 2.4 µsec
3 IC1601 yf
0 IC1601 td
5.1Vp-p
5.1Vp-p 2.4 µsec
2.4 µsec
4 IC1601 ys
qa IC1601 ta
5.0Vp-p
5.0Vp-p 2.4 µsec
2.4 µsec
5 IC1601 ya
qs IC1601 t;
5.1Vp-p 2.4 µsec
5.1Vp-p 2.4 µsec
6 IC1601 tl
qd IC1601 rj
5.2Vp-p 5.0Vp-p 2.6 µsec
7 IC1601 tk
2.6 µsec
2.5 µsec
qf IC1601 rk
5.0Vp-p 5.0Vp-p 2.5 µsec
4-115
WAVEFORMS DD-137
Waveforms and parts location of the VC-240/241 board are not shown. Pages from 4-116 to 4-123 are not shown.
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
4-4. MOUNTED PARTS LOCATION NS-10 BOARD (SIDE A)
CD-252 BOARD (SIDE A)
CK-92 BOARD (SIDE A)
CK-94 BOARD (SIDE A)
R001
A-1
CN3202 B-2
CN3202 B-2
S001
A-1
C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C116 C118 C119 C120 C122 C124 C125 C126 C127 C128 C129 C130 C131 C132 C151 C152
C-5 C-5 D-5 C-5 C-5 C-6 C-5 C-5 C-5 D-5 D-6 D-6 C-4 C-7 B-6 B-5 C-7 B-6 B-5 C-6 D-6 C-6 C-6 B-5 B-5 B-5 B-5 C-5 E-1 E-1
CN151 E-1 CN152 E-1 D101
D-5
FB101 FB102 FB103 FB104 FB105 FB106 FB108 FB109
D-5 D-5 C-6 C-6 C-6 B-4 C-5 D-6
IC102 IC103 IC104
C-5 C-6 B-5
L101 L103 L104 L105 L151
C-5 C-6 C-6 B-5 E-1
Q101 Q102 Q103 Q104
C-6 C-5 C-4 C-4
R102 R104 R105 R106 R107 R108 R109 R112 R113 R114 R122 R123 R151
D-6 C-6 C-6 C-6 D-5 C-6 D-6 C-4 B-6 C-4 C-5 B-6 E-1
X101
D-5
R3202 R3205 R3206 R3207 R3208 R3209 R3210 R3211 R3212 R3213 R3214 R3215 R3216
E-6 D-6 A-5 E-5 D-6 C-5 B-5 D-6 C-5 C-6 E-7 B-5 C-6
S3201 S3202
B-1 A-1
S3203 S3204 S3205 S3206 S3207 S3208 S3209 S3210 S3211 S3212 S3213 S3214 S3215 S3216 S3217 S3218
E-6 A-2 E-5 D-6 C-5 B-6 D-5 C-6 D-7 D-7 B-5 D-6 E-7 C-7 D-5 B-5
R3202 R3205 R3206 R3207 R3208 R3209 R3210 R3211 R3212 R3213 R3214 R3215 R3216
E-6 D-6 B-5 E-5 D-6 C-5 B-5 D-6 C-5 C-6 E-7 B-5 C-6
S3201 S3202
B-1 A-1
S3203 S3204 S3205 S3206 S3207 S3208 S3209 S3210 S3211 S3212 S3213 S3214 S3215 S3216 S3217 S3218
E-6 A-1 E-5 D-6 C-5 B-6 D-5 C-6 D-7 D-7 B-5 D-6 E-7 C-7 D-5 B-5
CK-92 BOARD (SIDE B)
CK-94 BOARD (SIDE B)
BT3201 D-10
BT3201 C-10
C3201 C3202 C3203
B-13 B-14 B-13
CN3201 CN3203 CN3204 CN3205 CN3206
B-13 B-10 E-10 B-12 B-11
D3201 D3202 D3203 D3204
B-10 B-10 B-10 B-10
R3201 R3203 R3204 R3217
B-13 A-14 E-10 B-10
C3201 C3202 C3203
B-13 B-14 B-13
CN3201 CN3203 CN3204 CN3205 CN3206
B-13 B-10 E-10 B-11 B-11
D3201 D3202 D3203 D3204
B-10 B-10 B-10 B-10
R3201 R3203 R3204 R3217
B-13 A-14 E-10 B-10
CD-252 BOARD (SIDE B) CN101 A-11 IC101
C-10
4-125
LOCATION NS-10, CD-253, FP-219, CK-92, CK-94
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
LB-64 BOARD (SIDE A)
JK-188 BOARD (SIDE A)
PD-123 BOARD (SIDE A)
PD-124 BOARD (SIDE A)
C2201
C3063 C3064 C3066 C3067
E-3 D-3 E-3 E-3
J3001 J3002 J3003 J3004
C-5 D-4 E-4 F-4
L3052
E-3
C2101 C2102 C2103 C2104 C2105 C2106 C2107 C2108 C2109 C2110 C2111 C2112 C2113 C2114 C2115 C2116 C2117 C2118 C2119 C2120 C2121 C2122 C2123 C2124 C2125 C2127 C2128 C2129 C2130 C2131 C2132 C2133 C2134 C2135 C2172 C2173 C2174 C2175 C2180 C2182
B-1 A-1 A-2 A-2 A-2 B-2 B-2 C-2 B-2 B-2 C-2 B-1 B-2 B-2 B-1 C-2 B-3 C-3 B-2 B-2 B-2 B-3 C-3 C-4 A-3 B-3 B-3 B-1 A-4 B-9 A-3 A-2 A-2 A-2 C-3 C-4 C-3 C-3 B-1 A-1
CN2101 CN2173 CN2174 CN2175 CN2176
B-12 A-3 C-4 C-1 A-2
C3101 C3102 C3103 C3104 C3105 C3106 C3107 C3108 C3109 C3110 C3111 C3112 C3113 C3114 C3115 C3116 C3117 C3118 C3119 C3120 C3121 C3122 C3123 C3124 C3125 C3126 C3127 C3128 C3130 C3131 C3132 C3133 C3134 C3135 C3136 C3137 C3171 C3173 C3174 C3175 C3176 C3177
D-2 D-1 D-1 B-1 D-1 C-2 C-1 C-1 C-1 C-1 C-2 C-2 B-2 D-2 C-2 D-2 B-3 D-2 C-2 C-2 C-2 C-2 C-3 C-3 C-3 B-1 C-3 B-3 B-2 B-2 B-3 C-1 C-1 C-1 B-2 B-1 D-2 B-3 B-3 B-3 B-3 D-1
D2101 D2102 D2103
B-2 B-3 B-10
CN1374 CN3101 CN3171 CN3172 CN3173
A-3 A-2 C-1 B-1 D-3
IC2104 IC2105 IC2106 IC2171
B-2 B-3 C-3 C-1
D3101 D3102 D3103 D3104 D3105
B-3 B-3 B-2 B-3 B-3
L2101 L2102 L2103 L2104 L2105 L2172 L2173
B-1 C-2 C-2 C-2 B-3 C-3 C-2
C-1
CN2201 C-1 D2202
A-1
IC2201 C-1 L2201 L2202
C-2 C-2
ND2201 A-1 Q2201
C-1
SE3051 C-3 SE3052 D-2
R2202 R2205
C-2 C-1
JK-188 BOARD (SIDE B)
LB-64 BOARD (SIDE B) C2202 C2203 C2204
C-3 C-3 C-3
CN2202 C-3 R2203 R2204
C-4 C-4
T2201
A-3
C3051 C3052 C3053 C3054 C3055 C3056 C3057 C3058 C3059 C3060 C3061 C3062 C3065
C-10 C-10 C-9 E-9 D-10 C-10 D-10 D-10 D-10 D-9 D-10 D-10 D-9
CN3001 A-11 D3001
C-7
FB3004 FB3005 FB3007 FB3008
F-9 E-8 D-9 D-9
IC3051 E-10
LOCATION LB-64, JK-188, PD-123, PD-124
R3001 R3002 R3003 R3004 R3005 R3051 R3052 R3053 R3054 R3055 R3056 R3057 R3058 R3059 R3060 R3061
C-8 B-8 C-8 E-9 D-8 D-10 C-10 C-10 D-10 E-10 E-9 E-10 E-9 E-9 E-10 C-10
VDR001 VDR002 VDR003 VDR004 VDR005 VDR006 VDR007
F-9 E-8 D-8 D-9 C-8 C-8 E-9
4-126
Q2102 Q2103 Q2104 Q2105 Q2106 Q2107 Q2108 Q2172 Q2173
C-3 B-3 B-3 B-3 A-3 B-2 A-3 C-3 C-3
R2101 R2103 R2105 R2106 R2107 R2108 R2109 R2111 R2112 R2113 R2114 R2116 R2117 R2118 R2119 R2120 R2121 R2122 R2123 R2124 R2125 R2126 R2127 R2129 R2133 R2134 R2135 R2140 R2141 R2142 R2143 R2144 R2145 R2146 R2147 R2148 R2149 R2150 R2151 R2152 R2153 R2154 R2175 R2176 R2177 R2178 R2180
A-3 B-3 A-1 A-2 A-2 A-2 A-2 B-2 B-1 B-2 B-2 B-2 B-2 B-2 B-2 B-3 B-3 B-5 A-3 B-8 B-3 B-4 B-3 B-3 B-7 B-6 C-4 B-3 A-3 B-2 A-1 C-3 C-3 A-4 B-3 B-3 A-3 A-3 B-11 A-2 A-2 A-2 C-3 C-3 A-1 A-1 B-1
IC3101 C-2 IC3102 B-2 IC3171 D-3 L3101 L3102 L3103 L3104 L3171 L3172
C-3 D-1 C-1 B-2 B-3 B-3
Q3102 Q3103 Q3104 Q3105 Q3106
C-3 C-3 B-1 B-1 A-2
Q3107 Q3108 Q3109 Q3110 Q3171 Q3172
B-2 B-1 B-2 B-3 C-3 B-3
R3101 R3102 R3104 R3105 R3106 R3107 R3108 R3109 R3110 R3111 R3112 R3113 R3114 R3115 R3116 R3117 R3118 R3119 R3120 R3121 R3122 R3123 R3124 R3125 R3126 R3127 R3128 R3131 R3132 R3133 R3135 R3136 R3137 R3138 R3139 R3140 R3141 R3142 R3143 R3144 R3146 R3147 R3148 R3149 R3150 R3151 R3151 R3152 R3153 R3154 R3155 R3156 R3157 R3158 R3159 R3160 R3171 R3172 R3173 R3174 R3175 R3176 R3177 R3178
C-1 D-1 C-1 C-1 C-2 B-3 D-2 C-2 C-2 C-2 C-2 B-3 C-2 B-3 C-2 C-2 C-2 C-2 C-2 C-3 C-3 C-3 D-2 C-3 C-3 B-2 B-2 B-1 B-2 A-2 C-2 A-3 C-3 A-2 B-1 C-1 C-1 C-1 B-3 A-2 C-3 B-1 B-2 A-2 B-2 B-2 B-2 A-3 A-3 A-2 B-3 B-2 C-3 C-3 C-3 C-2 B-1 A-1 A-1 D-2 C-3 C-3 D-1 D-1
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
SE-107 BOARD (SIDE A)
MA-385 BOARD (SIDE A)
DD-137 BOARD (SIDE A)
DD-137 BOARD (SIDE B)
PH081 C-1 PH082 C-2
C2005 C2006 C2007 C2009 C2011 C2014 C2015 C2017 C2018 C2019 C2020 C2021 C2022 C2024 C2025 C2026 C2030 C2031 C2032 C2034 C2042 C2043 C2071 C2091 C2103 C2106
E-2 E-3 E-3 D-2 E-2 E-3 E-3 E-2 E-3 E-3 E-2 D-3 D-2 D-3 E-2 D-2 D-2 D-2 D-2 D-2 E-1 D-3 B-2 D-4 E-2 E-2
C1639 C1648 C1651 C1652 C1653 C1654 C1656 C1657 C1658 C1659 C1660 C1661 C1662 C1663 C1664 C1665 C1666 C1667 C1669 C1672 C1673
D2001 D2061 D2062 D2063 D2071 D2072
E-2 D-4 E-2 E-1 A-2 A-3
FB2001 FB2002 FB2061 FB2062 FB2063 FB2064
E-1 E-2 E-1 E-1 E-1 E-1
C1601 C1602 C1603 C1604 C1605 C1606 C1607 C1608 C1609 C1610 C1611 C1612 C1613 C1614 C1615 C1616 C1617 C1618 C1619 C1620 C1621 C1622 C1623 C1624 C1625 C1626 C1627 C1628 C1629 C1630 C1631 C1632 C1633 C1634 C1635 C1636 C1637 C1638 C1640 C1641 C1642 C1643 C1644 C1645 C1646 C1647 C1649 C1650 C1655 C1668 C1670 C1671 C1674
IC2002 D-3 IC2091 D-4 Q2071 Q2072 Q2073 Q2074
B-2 A-2 B-2 A-2
R2007 R2008 R2011 R2012 R2013 R2014 R2015 R2016 R2018 R2021 R2022 R2025 R2026 R2028 R2029 R2035 R2061 R2062 R2063 R2064 R2065 R2071 R2072 R2073 R2074 R2075 R2091
E-2 E-2 E-3 E-2 D-3 E-2 D-2 D-3 D-2 D-2 D-2 E-2 D-2 D-2 D-2 D-3 D-4 E-3 E-3 E-3 D-3 B-2 B-2 A-2 B-2 A-2 D-4
S2061
E-4
VDR201 E-1
MA-385 BOARD (SIDE B) C2008 C2010 C2012 C2023 C2027 C2028 C2029 C2033 C2035 C2036 C2037 C2038 C2039 C2041 C2044 C2045 C2046 C2047 C2072 C2073
E-8 E-7 E-8 D-6 D-6 D-6 D-7 D-7 D-7 D-8 D-8 D-8 D-7 D-8 E-8 E-8 E-8 E-8 A-7 B-8
R2009 R2010 R2017 R2019 R2020 R2023 R2024 R2027 R2030 R2031 R2032 R2033 R2034 R2036 R2037 R2038 R2039 R2051 R2052
D-7 E-8 D-6 D-6 D-6 D-6 D-6 D-7 D-7 D-8 D-7 D-8 D-8 E-8 E-8 E-8 E-8 D-7 D-7
A-1 A-2 A-3 A-5 A-4 A-4 B-4 B-5 A-5 B-4 B-4 B-5 A-5 B-4 B-5 B-4 B-3 B-3 B-3 B-4 B-5
CN1601 B-1 CN1602 B-1 CN1604 B-4 D1602 D1614 D1615 D1616
B-1 A-1 A-4 A-1
F1601 F1602 F1603 F1604 F1605 F1606
B-1 B-1 B-2 B-2 B-2 B-1
IC1602 B-4 L1601 L1602 L1603 L1604 L1605 L1606 L1607 L1608 L1609 L1610 L1611 L1612 L1613 L1614 L1615 L1616 L1619 L1624
A-2 A-2 B-2 A-2 B-2 A-3 A-5 A-4 A-4 B-4 A-4 B-4 B-5 B-5 B-5 B-5 A-4 B-3
LF1601 B-1 Q1615 Q1617 Q1624
CN2001 D-7 CN2051 E-7 CN2071 B-8
A-1 A-1 A-2
Q1625 Q1626 Q1627 Q1628 Q1629 Q1632 Q1635 Q1637 Q1639 Q1641 Q1643 Q1646 Q1647 Q1648 Q1649 Q1650 Q1653
A-1 A-1 B-4 B-4 B-3 B-3 B-3 B-3 B-3 B-3 B-3 B-4 B-4 B-3 B-4 B-3 B-4
R1601 R1607 R1608 R1645 R1646 R1647 R1648 R1649 R1650 R1652 R1654 R1655 R1656 R1657 R1658 R1661 R1662 R1664 R1666 R1668 R1669 R1672 R1673 R1674 R1675 R1676 R1677 R1678 R1680 R1682 R1683 R1684 R1685 R1686 R1687 R1688 R1689 R1690 R1691 R1692 R1693 R1694
B-1 B-1 B-1 A-2 A-1 A-2 A-2 A-2 A-1 B-4 B-3 B-4 B-4 B-4 B-4 B-3 B-3 B-3 B-3 B-4 B-3 B-3 B-3 B-3 B-3 B-3 B-3 A-2 B-3 A-1 B-4 B-3 B-4 B-3 B-4 B-4 B-4 B-4 B-4 B-3 B-4 B-5
T1601 T1602
B-2 B-2
B-10 B-7 B-7 B-6 B-7 B-9 B-6 B-9 B-6 B-9 B-7 B-6 B-9 B-9 B-8 A-9 B-6 B-6 B-8 B-6 B-7 B-8 B-8 B-8 B-6 B-8 B-7 B-7 A-7 A-7 A-7 B-7 B-9 A-9 B-9 B-9 A-8 B-9 A-9 B-9 B-8 B-9 B-8 B-9 B-8 B-9 B-9 B-8 B-8 B-8 B-7 B-8 B-7
CN1603 A-7 D1601 D1604 D1606 D1607 D1608 D1609 D1610 D1611 D1612 D1613
B-10 B-10 B-9 B-8 B-8 B-8 B-9 B-8 B-8 B-9
IC1601 B-7
D-8 D-6
L1617 L1618
B-8 B-8
FB2003 E-8
Q1601 Q1602 Q1603 Q1604 Q1605
B-10 B-10 B-10 A-10 B-9
D2002 D2091
J2001 J2002
D-9 E-9
L2001
D-8
4-127E
Q1606 Q1607 Q1608 Q1609 Q1610 Q1611 Q1612 Q1613 Q1614 Q1616 Q1618 Q1619 Q1620 Q1621 Q1622 Q1623 Q1633 Q1634 Q1636
B-8 B-8 B-8 B-9 A-9 A-9 A-9 B-9 A-8 A-10 B-9 A-9 A-9 A-8 B-9 B-8 B-8 B-8 B-8
R1602 R1603 R1604 R1605 R1606 R1609 R1610 R1611 R1612 R1613 R1614 R1615 R1616 R1617 R1618 R1619 R1620 R1621 R1622 R1623 R1624 R1625 R1626 R1627 R1628 R1629 R1630 R1631 R1632 R1633 R1635 R1636 R1637 R1638 R1639 R1640 R1641 R1642 R1643 R1644 R1651 R1663 R1665 R1667 R1670 R1671 R1679 R1681 R1695 R1696 R1697 R1698 R1699 R1700 R1701 R1702
B-10 B-10 B-10 B-10 A-10 B-7 B-7 B-7 B-6 B-8 B-7 B-6 B-6 B-8 B-6 B-8 B-6 B-6 B-6 B-6 B-6 B-7 B-6 B-6 B-6 B-6 B-6 B-6 A-6 B-6 B-6 B-6 A-7 B-7 B-7 A-7 B-8 B-8 B-7 A-7 B-8 B-8 B-8 B-8 B-8 B-8 B-8 B-8 B-7 B-7 B-7 B-7 B-7 B-7 B-7 B-7
LOCATION SE-107, MA-385, DD-137
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E SECTION 5 ADJUSTMENTS 1.
Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Procedure 1 Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. (Machine before starting repair)
PC
PC
(Machine after a board is replaced)
Download the saved data to a machine.
Save the EVR data to a personal computer.
Procedure 2 Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the replaced board. Remove the EEPROM and install it.
(Former board)
(New board)
Procedure 3 When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or installed, save the data from the same model of the same destination, and download it. (Machine to be repaired)
PC
(Machine to be repaired)
Download the data. Save the data.
(The same model of the same destination)
After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-3 for the items to be checked.)
5-1
1-1. Adjusting items when replacing main parts and boards. • Adjusting items when replacing main parts (DCR-TRV6/TRV6E/TRV11/TRV11E) When replacing main parts, adjust the items indicated by z in the following table. Note1: When replacing the drum assy., reset the data of page: 2, address: A2 to A4 to “00”. (Refer to “Record of Use check” of “5-4. SERVICE MODE”) Replaced parts
Adjustment Section
Adjustment
Parts replacement
Lens device Mechanism deck Color EVF block LCD902 (LCD panel) LCD block LCD901 (LCD panel) LCD block ND901 (Fluorescent tube) LCD block Inverter unit Control switch block (FK-30150) Mechanism deck M901 (Drum assy) Note1 Mechanism deck M902 (Capstan motor) Mechanism deck LS chassis D3 assy JK-188 board SE3051/3052 (PITCH/YAW sensor) PD-123 board IC2104 (RGB driver (LCD)) *1 PD-123 board IC2105 (Timing generator (LCD)) *1 PD-124 board IC3101 (RGB driver (LCD)) *2 PD-124 board IC3102 (Timing generator (LCD)) *2 LB-64 board ND2201 (Fruorescent tube (EVF)) VC-241 board IC1802 (RGB driver (EVF)) VC-241 board IC1803 (Timing generator (EVF)) FP-219 flexible IC101 (CCD imager) VC-241 board IC702, X701 (Timing generator) VC-241 board IC701 (CDS, AGC, A/D conv.) VC-241 board IC204 (Lens predriver) VC-241 board IC751 (Camera process, EVR) VC-241 board IC1301 (LINE IN/OUT AMP) VC-241 board IC301 (DV signal process) VC-241 board IC101 (EQ, A/D conv., PLL) VC-241 board IC102 (REC/PB AMP) VC-241 board IC1901 (IR transmitter)
Block replacement
Initialization Initialization of C, D, 8 page data of B, C, D, E, Initialization of B page data *1 F, 7, 8 page data Initialization of E, F, 7 page data 36MHz origin oscillation adj. Zoom center adj. z Hall adj. z Flange back adj. z Optical axis adj. z Camera Color reproduction adj. MAX GAIN adj. AWB & LV standard data input Auto white balance adj. Mechanical shutter adj. Angular velocity sensor sensitivity adj. z VCO adj. z RGB AMP adj. z Color EVF Contrast adj. z Backlight consumption current adj. z White balance adj. z z z VCO adj. z z RGB AMP adj. *1 z Bright adj. *2 z Black limit adj. *2 z LCD Contrast adj. z z V-COM level adj. *1 z Center level adj. *2 z V-COM adj. z z z White balance adj. zz z z z System control Serial No. input CAP FG duty adj. z z Switching position adj. z z Servo, RF AGC center level adj. z z APC & AEQ adj. z z PLL f0 & LPF f0 adj. z z Chroma BPF f0 adj. Video S VIDEO OUT Y level adj. S VIDEO OUT Cr, Cb level adj. IR video carrier frequency adj. IR IR video deviation adj. IR audio deviation adj. Mechanism Tape path adj. z z z z
Table. 5-1-1(1).
5-2
z
z z z z z z
z z z z z z z z
z z
z
z z z z z z z z z zz zz z zz z z z
z z z
Ver 1.1 2000. 06
• Adjusting items when replacing a board or EEPROM (DCR-TRV6/TRV6E/TRV11/TRV11E) When replacing a board or EEPROM, adjust the items indicated by z in the following table. *1: DCR-TRV11/TRV11E model only *2: DCR-TRV6/TRV6E model only
Adjustment
VC-241 board JK-188 board PD-123 board PD-124 board LB-64 board VC-241 board VC-241 board VC-241 board
Adjustment Section
(COMPLETE) (COMPLETE) (COMPLETE) *1 (COMPLETE) *2 (COMPLETE) IC801 (EEPROM) IC502 (EEPROM) IC1407 (Flash memory) *1
Board replacement
Initialization Initialization of C, D, 8 page data of B, C, D, E, Initialization of B page data *1 F, 7, 8 page data Initialization of E, F, 7 page data 36MHz origin oscillation adj. Zoom center adj. Hall adj. Flange back adj. Optical axis adj. Camera Color reproduction adj. MAX GAIN adj. AWB & LV standard data input Auto white balance adj. Mechanical shutter adj. Angular velocity sensor sensitivity adj. VCO adj. RGB AMP adj. Color EVF Contrast adj. Backlight consumption current adj. White balance adj. VCO adj. RGB AMP adj. *1 Bright adj. *2 Black limit adj. *2 LCD Contrast adj. V-COM level adj. *1 Center level adj. *2 V-COM adj. White balance adj. System control Serial No. input CAP FG duty adj. Switching position adj. Servo, RF AGC center level adj. APC & AEQ adj. PLL f0 & LPF f0 adj. Chroma BPF f0 adj. Video S VIDEO OUT Y level adj. S VIDEO OUT Cr, Cb level adj. IR video carrier frequency adj. IR IR video deviation adj. IR audio deviation adj. Mechanism Tape path adj.
z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z
Table. 5-1-1(2).
5-3
z z
z z z z z z z z z z z z z z z z z z z z z z z
• Adjusting items when replacing main parts (DCR-TRV20/TRV20E) When replacing main parts, adjust the items indicated by z in the following table. Note1: When replacing the drum assy., reset the data of page: 2, address: A2 to A4 to “00”. (Refer to “Record of Use check” of “5-4. SERVICE MODE”) Replaced parts
Adjustment Section
Adjustment
Parts replacement
Lens device Mechanism deck Color EVF block LCD902 (LCD panel) LCD block LCD901 (LCD panel) LCD block ND901 (Fluorescent tube) LCD block Inverter unit Control switch block (FK-30150) Mechanism deck M901 (Drum assy) Note1 Mechanism deck M902 (Capstan motor) Mechanism deck LS chassis D3 assy JK-188 board SE3051/3052 (PITCH/YAW sensor) PD-123 board IC2104 (RGB driver (LCD)) *1 PD-123 board IC2105 (Timing generator (LCD)) *1 PD-124 board IC3101 (RGB driver (LCD)) *2 PD-124 board IC3102 (Timing generator (LCD)) *2 LB-64 board ND2201 (Fruorescent tube (EVF)) VC-240 board IC1802 (RGB driver (EVF)) VC-240 board IC1803 (Timing generator (EVF)) CD-252 board IC101 (CCD imager) CD-252 board IC102, X101 (Timing generator) CD-252 board IC104 (CDS, AGC,) VC-240 board IC204 (Lens predriver) VC-240 board IC701 (A/D converter) VC-240 board IC1301 (LINE IN/OUT AMP) VC-240 board IC301 (DV signal process) VC-240 board IC101 (EQ, A/D conv., PLL) VC-240 board IC102 (REC/PB AMP) VC-240 board IC1901 (IR transmitter) VC-240 board IC803 (EVR)
Block replacement
Initialization Initialization of C, D, 8 page data Initialization of B page data of B, C, D, E, F, 7, 8 page data Initialization of E, F, 7 page data 54MHz/66MHz origin oscillation adj. Zoom center adj. z Hall adj. z MR adj. z Flange back adj. z Camera Color reproduction adj. MAX GAIN adj. AWB & LV standard data input Auto white balance adj. Mechanical shutter adj. Angular velocity sensor sensitivity adj. z VCO adj. z RGB AMP adj. z Color EVF Contrast adj. z Backlight consumption current adj. z White balance adj. z z z VCO adj. z z RGB AMP adj. *1 z Bright adj. *2 z Black limit adj. *2 z LCD Contrast adj. z z V-COM level adj. *1 z Center level adj. *2 z V-COM adj. z z z White balance adj. zz z z z System control Serial No. input CAP FG duty adj. z z Switching position adj. z z Servo, RF AGC center level adj. z z APC & AEQ adj. z z PLL f0 & LPF f0 adj. z z Chroma BPF f0 adj. Video S VIDEO OUT Y level adj. S VIDEO OUT Cr, Cb level adj. IR video carrier frequency adj. IR IR video deviation adj. IR audio deviation adj. Mechanism Tape path adj. z zz z
Table. 5-1-2(1).
5-4
z
z z z
z z
z z
z
z
z z
z z
z z
z z
z
z z zz zz zz z zz zz zz z
zz zz zz
• Adjusting items when replacing a board or EEPROM (DCR-TRV20/TRV20E) When replacing a board or EEPROM, adjust the items indicated by z in the following table. *1: DCR-TRV20 model only *2: DCR-TRV20E model only *3: Perform this adjustment when replace the CCD imager (IC101) and this board at the same time.
Adjustment
CD-252 board VC-240 board JK-188 board PD-123 board PD-124 board LB-64 board VC-240 board VC-240 board VC-240 board
Adjustment Section
(COMPLETE) (COMPLETE) (COMPLETE) (COMPLETE) *1 (COMPLETE) *2 (COMPLETE) IC801 (EEPROM) IC502 (EEPROM) IC1406 (EEPROM)
Board replacement
Initialization Initialization of C, D, 8 page data of B, C, D, E, Initialization of B page data F, 7, 8 page data Initialization of E, F, 7 page data 54MHz/66MHz origin oscillation adj. Zoom center adj. Hall adj. MR adj. Flange back adj. Camera Color reproduction adj. MAX GAIN adj. AWB & LV standard data input Auto white balance adj. Mechanical shutter adj. Angular velocity sensor sensitivity adj. VCO adj. RGB AMP adj. Color EVF Contrast adj. Backlight consumption current adj. White balance adj. VCO adj. RGB AMP adj. *1 Bright adj. *2 Black limit adj. *2 LCD Contrast adj. V-COM level adj. *1 Center level adj. *2 V-COM adj. White balance adj. System control Serial No. input CAP FG duty adj. Switching position adj. Servo, RF AGC center level adj. APC & AEQ adj. PLL f0 & LPF f0 adj. Chroma BPF f0 adj. Video S VIDEO OUT Y level adj. S VIDEO OUT Cr, Cb level adj. IR video carrier frequency adj. IR IR video deviation adj. IR audio deviation adj. Mechanism Tape path adj.
z z z z zz z z z z z z z zz z *3 z z z z *3 z z *3 z z z z z z z z z z z z z z z zz z z z z z z z zz z z z z z zz z zz z z z z z z z z z z z z z z z
Table. 5-1-2(2).
5-5
z z
z z z z z z z
z z z z z z z z z z z z z
5-1. CAMERA SECTION ADJUSTMENT 1-1.
PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)
1-1-1. List of Service Tools • Oscilloscope • Regulated power supply Ref. No.
• Color monitor • Digital voltmeter
Name
• Vectorscope Parts Code
Usage
ND filter 1.0
Auto white balance adjustment/check White balance adjustment/check J-6080-808-A White balance check
J-2
ND filter 0.4 ND filter 0.1
J-6080-806-A White balance check J-6080-807-A White balance check
J-3 J-4
Pattern box PTB-450 Color chart for pattern box
J-6082-200-A J-6020-250-A
J-1
Filter for color temperature correction (C14)
J-6080-058-A
J-6
Adjustment remote commander (RM-95 upgraded). J-6082-053-B (Note 1) Siemens star chart J-6080-875-A For checking the flange back
J-7
Clear chart for pattern box
J-6080-621-A
J-8
CPC-8 jig
For adjusting the video section J-6082-388-A For adjusting the color viewfinder For adjusting the LCD block
J-9
Extension cable (80P, 0.4mm)
J-6082-395-A
J-10
IR receiver jig
For extension between the DD-137 board (CN1603) and the VC-240/241 board (CN002) J-6082-383-A For adjusting the IR transmitter
J-11 J-12
Mini pattern box Camera table
J-6082-353-B For adjusting the flange back J-6082-384-A For adjusting the flange back
J-5
Note 1: If the micro processor IC in the adjustment remote commander is not the new micro processor (UPD7503G-C56-12), the pages cannot be switched. In this case, replace with the new micro processor (8-759-148-35).
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
J-12
Fig. 5-1-1.
5-6
1-1-2.
Preparations
Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled.
1)
Pattern Box
Connect the equipment for adjustments according to Fig. 5-1-2.
Note 3: As removing the cabinet (R) (removing the VC-240/241 board CN003) means removing the lithium 3V power supply (BT3201), data such as date, time, user-set menus will be lost. After completing adjustments, reset these data. If the cabinet (R) has been removed, the self-diagnosis data, data on history of use (total drum rotation time etc. ) will be lost. Before removing, note down the self-diagnosis data and the data on history use (data of page: 2, address: A2 to AA). (Refer to “SELF-DIAGNOSIS FUNCTION” for the self-diagnosis data, and to “5-4.Service Mode” for the data on the history use.)
1.5m
Note 4: Setting the “Forced Camera Power ON” Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the camera power to be turned on with the control switch block (FK-30150) removed. After completing adjustments, be sure to exit the “Forced Camera Power ON Mode”.
Front of the lens
Fig. 5-1-2.
Note 5: Exiting the “Forced Camera Power ON” Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.
5-7
Extension cable J-6082-395-A (80P 0.4mm)
Must be connected when performing the color EVF system adjustments. AC power adaptor (8.4Vdc) CN1604
Adjustment remote commander
AC - L10 or AC - VQ800
Battery terminal
CN1603
DD-137 board CN1601 CN1602
Front panel block FP-180
LANC/ DIGITAL I/O jack
CN008 CN007 CN006
CN005
CN101 CN002
DC IN jack AUDIO/VIDEO jack JK-188 board
VC-240/241 board CN701 CN009 CN001
MA-385 board CN2071
CN003
Must be connected when performing the video system, color EVF system or LCD system adjustments.
AUDIO L (White) AUDIO R (Red)
FP-179
VIDEO (Yellow)
CK-92/94 board
Color monitor
CN3205 CN3203
CN3201 CN3206
CPC-8 jig (J-6082-388-A) Vector scope CN3204
Cabinet (R)
Terminated at 75 Ω
Note : VC-240 board : DCR-TRV20/TRV20E VC-241 board : DCR-TRV6/TRV6E/TRV11/TRV11E CK-92 board : DCR-TRV11/TRV11E/TRV20 CK-94 board : DCR-TRV6/TRV6E/TRV20E
Fig. 5-1-3.
5-8
1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. 1. 2. 3. 4. 5. 6. 7.
POWER switch (PS-30150 block) ......................... CAMERA NIGHT SHOT switch (Lens block) ................................. OFF DEMO MODE (Menu setting) ........................................ OFF DIGITAL ZOOM (Menu setting) .................................... OFF STEADY SHOT (Menu setting) ...................................... OFF PROGRAM AE (CF-30150) ........................................ AUTO WHITE BALANCE (Menu setting) ............................ AUTO
8. 9. 10. 11. 12. 13.
16 : 9 WIDE (Menu setting) ............................................ OFF PICTURE EFFECT (Menu setting) ................................. OFF DISPLAY (Menu setting) .................................. V-OUT/LCD DISPLAY (CK-92/94 board) ............................................ ON FOCUS switch (MA-385 board) ........................... MANUAL DIGITAL EFFECT (CK-92/94 board) ............................ OFF
2. Order of Adjustments Basically carry out adjustments in the order given.
Color bar chart (Color reproduction adjustment frame )
Electronic beam scanning frame
A B
A=B
C
C=D
D Yellow Cyan Green White Magenta Red Blue
Blue
Yellow Cyan Green White Magenta Red
H
CRT picture frame
V
B A
Fig. b (TV monitor picture)
Enlargement
Fig. a (Video output terminal output waveform)
Difference in level
B
Adjust the camera zoom and direction to obtain the output waveform shown in Fig. a and the TV monitor display shown in Fig. b.
A
Fig.5-1-4. 3. Subjects 1) Color bar chart (Color reproduction adjustment frame) When performing adjustments using the color bar chart, adjust the picture frame as shown in Fig. 5-1-4. (Color reproduction adjustment frame) 2) Clear chart (Color reproduction adjustment frame) Remove the color bar chart from the pattern box and insert a clear chart in its place. (Do not perform zoom operations during this time.) 3) Flange back adjustment chart Make the chart shown in Fig. 5-1-5 using A0 size (1189mm × 841mm) black and white vellum paper.
White 841mm Black
1189mm
Fig. 5-1-5. Note: Use matte vellum paper bigger than A0, and make sure the edges of the black and white paper joined together are not rough.
5-9
1-2.
3. C Page Table
INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA
1-2-1.
Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8 Page Data”.)
INITIALIZATION OF C, D, 8 PAGE DATA
1. Initializing the C, D, 8 Page Data
Address Note1: If “Initializing the C, D, 8 Page Data” is performed, all data of the C page, D page and 8 page will be initialized. (It is impossible to initialize a single page.) Note2: If the C, D, 8 page data has been initialized, the following adjustments need to be performed again. 1) Modification of C, D, 8 page data 2) Serial No. input 3) Servo and RF system adjustments 4) Video system adjustments 5) Color viewfinder system adjustments 6) LCD system Adjustments
Adjusting page
C
Adjusting Address Adjusting page
10 to FF D
Adjusting Address Adjusting page
10 to FF 8
Adjusting Address
00 to FF
00 to 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D to 3F
Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 81, and check that the data is “00”. 3) Select page: 3, address: 80, set data: 0A, and press the PAUSE button of the adjustment remote commander. 4) Select page: 3, address: 80, and check that the data changes to “1A”. 5) Perform “Modification of C, D, 8 Page Data”. 2. Modification of C, D, 8 Page Data If the C, D, 8 page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model.
40 41 42 43 to 4B
Note: If copy the data built in the different model, the camcorder may not operate.
3)
4)
When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory. Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value.
4C 4D
Processing after Completing Modification of C, D, 8 Page data 1) Select page: 2, address: 00, and set data: 29. 2) Select page: 2, address: 01, and set data: 29, and press the PAUSE button of the adjustment remote commander.
4E 4F 50 51
Note: If the following symptoms occur after completing of the “Modification of C, D, 8 page data”, check that the data of the “Fixed data-2” addresses of D page are same as those of the same model of the same destination. 1) The battery end mark on the LCD or viewfinder screen is flashing. 2) The power is shut off so that unit cannot operate.
52 to 63 64 65 to 83 84 85
5-10
Initial value EE 00 00 00
E0 2A 2A 32 32 25 3E 3E DC 99
88 E3 A1 04 20
03
Remark Switching position adj.
Fixed data-1 (Initialized data) Cap FG duty adj. Fixed data-2 AEQ adj. Fixed data-1 AEQ adj. Fixed data-1 AGC center level adj. PLL f0 adj. APC adj. LPF f0 adj. Fixed data-1 (Initialized data) S VIDEO out Y level adj. S VIDEO out Cr level adj. S VIDEO out Cb level adj. Chroma BPF f0 adj. PLL f0 fine adj. Fixed data-1 (Initialized data) APC adj. Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1
Address 86 87 88 89 8A to 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 to BF C0 C1 to D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 to E3 E4 E5
Initial value
Remark
Address
Initial value
E6
Fixed data-2 (Modified data. Copy the data built in the same model.)
E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF
Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)
Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)
Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.)
08 00 46 01 02 00 00 00
Remark Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Serial No. input
Fixed data-1 (Initialized data)
00 00 00 00 00 00 00 00 00 00 00 00
Emergency memory address
Table. 5-1-3.
Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)
Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)
5-11
Ver 1.1 2000. 06
4. D Page Table Address Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8 Page Data”.)
64 65
*1: TRV11/TRV11E/TRV20 model only *2: TRV6/TRV6E/TRV20E model only *3: TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E Address 00 to 0F 10 11 12 13 14 15 to 1C 1D 1E to 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 to 41 42 43 44 45 46 to 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D to 63
Initial value 00
Initial value
66 67 68
Remark 69 to 8D 8E 8F 90 to 91 92 5D/7D *4 93 5D/7D *4 94 95 AC 96 97 80 98 80 99 1D 9A 9B 9C E0 9D E0 9E 11 9F A0 A1 A2 45/6F/A5/A5/ 98/6C *3 A3 6B/4A/A5/A5/ 98/61 *3 A4 27/27/88/88/ 91/27 *3 A5 B5/B5/2B/2B/ 2C/B5 *3 A6 05/05/00/00/ 00/05 *3 A7 B9/B9/CE/CE/ A1/B9 *3 A8 8A/8A/7F/7F/ 7F/8A *3 A9 72/72/87/87/ 87/72 *3 AA 25/25/37/37/ 3F/25 *3 AB 27/27/80/80/ 80/64 *3 AC AD AE AF B0 B1 B2 B3 B4
Test mode Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)
Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)
Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)
5-12
Remark Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 Fixed data-1 VCO adj. (EVF) *4: NTSC/PAL Fixed data-2 RGB AMP adj.(EVF) Fixed data-1 White balance adj. (EVF) Contrast adj. (EVF) Fixed data-1 Fixed data-2 Backlight consumption current adj. (EVF) Fixed data-1 (Initialized data) VCO adj. (LCD)
V-COM adj. (LCD) RGB AMP adj. (LCD) *1 Bright adj.(LCD) *2 Black limit adj.(LCD) *2 Fixed data *1 V-COM level adj. (LCD) *1 Fixed data *2 White balance adj. (LCD)
Contrast adj. (LCD) Center level adj.(LCD) *2 Fixed data *1 Fixed data-2 (Modified data. Copy the data built in the same model.)
Fixed data-1 (Initialized data) Fixed data-2
5. 8 Page Table Address B5
B6 B7 B8 B9 BA BB to C3 C4 C5 C6 C7 to D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC to FF
Initial value
Remark Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8 Page Data”.)
Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data)
Address
Remark
00 to 52 Fixed data-1 (Initialized data) 53 Fixed data-2 (Modified data. Copy the data built in the same model.) 54 to 98 Fixed data-1 (Initialized data) 99 Fixed data-2 (Modified data. Copy the data built in the same model.) 9A to A4 Fixed data-1 (Initialized data) A5 Fixed data-2 A6 Fixed data-1 A7 Fixed data-2 A8 (Modified data. Copy the data built in the same model.) A9 to FF Fixed data-1 (Initialized data)
Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data)
Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 (Initialized data)
Table. 5-1-5.
Table. 5-1-4.
5-13
Ver 1.1 2000. 06
1-2-2.
INITIALIZATION OF B PAGE DATA (DCR-TRV11/TRV11E/TRV20/TRV20E)
3. Initializing the B Page Data (DCR-TRV11/TRV11E) Note: If the B page data has been initialized, the following adjustments need to be performed again. 1) Modification of B page data
Note: When reading the B page data, insert a “Memory Stick” into the “Memory Stick” slot.
Switch setting: POWER ................................................................. MEMORY 1. Initializing the B Page Data (DCR-TRV20/TRV20E) Note: If the B page data has been initialized, the following adjustments need to be performed again. 1) Modification of B page data
Adjusting page
B
Adjusting Address
00 to FF
B
Adjusting Address
00 to FF
Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 3) Select page: 2, address: 8F, set data: 03, and press the PAUSE button. 4) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 5) Select page: 2, address: 8F, set data: 00, and press the PAUSE button. 6) Select page: 5, address: 0E, set data: 00, and press the PAUSE button. 7) Select page: 5, address: 01, set data: F3, and press the PAUSE button. 8) Select page: 5, address: 00, set data: 01, and press the PAUSE button. 9) Select page: 5, address: 0E, and check that the data is “01”. 10) Perform “Modification of B Page Data”.
Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 3) Select page: 2, address: 8F, set data: 03, and press the PAUSE button. 4) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 5) Select page: 2, address: 8F, set data: 00, and press the PAUSE button. 6) Select page: 5, address: 01, set data: F3, and press the PAUSE button. 7) Select page: 5, address: 00, set data: 01, and press the PAUSE button. 8) Select page: 5, address: 01, and wait for three seconds. 9) Select page: 5, address: 00, and check that the data is “00”. 10) Select page: 5, address: 02, and check that the data is “00”. 11) Perform “Modification of B Page Data”.
4. Modification of B Page Data (DCR-TRV11/TRV11E) If the B page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Preparations: 1) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 2) Select page: 2, address: 8F, set data: 03, and press the PAUSE button. 3) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 4) Select page: 2, address: 8F, set data: 00, and press the PAUSE button.
2. Modification of B Page Data (DCR-TRV20/TRV20E) If the B page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Preparations: 1) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 2) Select page: 2, address: 8F, set data: 03, and press the PAUSE button. 3) Select page: 2, address: 8F, set data: 02, and press the PAUSE button. 4) Select page: 2, address: 8F, set data: 00, and press the PAUSE button.
Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camcorder may not operate.
Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model.
3)
When changing the data, don’t press the PAUSE button.
Processing after Completing Modification of B Page data: 1) Select page: 5, address: 0E, set data: 00, and press the PAUSE button. 2) Select page: 5, address: 01, set data: FB, and press the PAUSE button. 3) Select page: 5, address: 00, set data: 01, and press the PAUSE button. (The changed data are written in the flash memory.) 4) Select page: 5, address: 0E, and check that the data is “01”. 5) Select page: 2, address: 00, and set data: 29. 6) Select page: 2, address: 01, set data: 29, and press the PAUSE button.
Note: If copy the data built in the different model, the camcorder may not operate.
3)
Adjusting page
When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory.
Processing after Completing Modification of B Page data: 1) Select page: 2, address: 00, and set data: 29. 2) Select page: 2, address: 01, set data: 29, and press the PAUSE button.
5-14
Ver 1.1 2000. 06
5. B Page Table
1-2-3.
Note: Fixed data-1: Initialized data. (Refer to “1. or 3. Initializing the B Page Data”.) Fixed data-2: Modified data. (Refer to “2. or 4. Modification of B Page Data”.)
1. Initializing the E, F, 7 Page Data
Address
INITIALIZATION OF E, F, 7 PAGE DATA
Note1: If “Initializing the E, F, 7 Page Data” is performed, all data of the E page, F page and 7 page will be initialized. (It is impossible to initialize a single page.) Note2: If the E, F, 7 page data has been initialized, following adjustments need to be performed again. 1) Modification of E, F, 7 page data 2) Camera system adjustments 3) IR transmitter adjustments
Remark
00 Fixed data-2 01 to 16 Fixed data-1 (Initialized data) 17 Fixed data-2 (Modified data. Copy the data built in the same 18 model.) 19 1A to 20 Fixed data-1 (Initialized data) 21 Fixed data-2 22 to 4F Fixed data-1 (Initialized data) 50 Fixed data-2 51 to 53 Fixed data-1 (Initialized data) 54 Fixed data-2 55 to 5D Fixed data-1 (Initialized data) 5E Fixed data-2 5F 60 to 6F Fixed data-1 (Initialized data) 70 Fixed data-2 71 to FF Fixed data-1 (Initialized data)
Adjusting page
F
Adjusting Address Adjusting page
10 to FF E
Adjusting Address Adjusting page
00 to FF 7
Adjusting Address
DCR-TRV6/TRV6E/TRV11/TRV11E: 00 to 59 DCR-TRV20/TRV20E: 00 to A3 (Note3) 00 to B5 (Note4)
Note3: Camera microprocessor ver. 1.0 Note4: Camera microprocessor ver. 2.0 or later
Switch setting: POWER .................................................................. CAMERA Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 01, and set the following data and press the PAUSE button. 2D: DCR-TRV6/TRV11/TRV20 (NTSC) 2F: DCR-TRV6E/TRV11E/TRV20E (PAL) 3) Select page: 6, address: 03, set data: 01, and press the PAUSE button. 4) Select page: 6, address: 02, and check that the data changes to “01”. 5) Perform “Modification of E, F, 7 Page Data”.
Table. 5-1-6.
2. Modification of E, F, 7 Page Data If the E, F, 7 page data has been initialized, change the data of the “Fixed data-2” address shown in the following table by manual input. Version check of the camera microprocessor: 1) The data of page: 6, address: FF shows the version of the camera microprocessor (VC-240/241 board IC802). Data 01 02
Version 1.0 2.0
Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camcorder may not operate.
3)
4)
When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory. Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value.
Processing after Completing Modification of E, F, 7 Page data 1) Turn off the power and turn on again.
5-15
3. F Page Table Address Initial value *5 VC-240 VC-241 38 39 3A 3B 3C 00 00 3D F1/EF F1/EF *4 *4 3E 3F 40 80 80 41 40 40 42 43 44 45 46 47 48 49 4A 84 51 4B 4A 19 4C AD 22 4D 47 20 4E F0 93 4F 21 13 50 80 00 51 80 00 52 40 *3 53 C0 *3 54 40 *3 55 C0 *3 56 40 *3 57 C0 *3 58 40 *3 59 C0 *3 5A 8F 46 5B EF 00 5C 19 19 5D 00 00 5E 1B 2A 5F 86 00 60 00 00 61 00 00 62 00 00 63 00 *3 64 65 66 47/5E 56/7C *4 *4 67 51/60 68/6F *4 *4 68 69 *3 00 6A 6B
Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”.)
*1: *2: *3: *4:
DCR-TRV6/TRV6E/TRV11/TRV11E model only DCR-TRV20/TRV20E model only Fixed data-1 NTSC/PAL NTSC: DCR-TRV6/TRV11/TRV20 PAL: DCR-TRV6E/TRV11E/TRV20E *5: VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E Address Initial value *5 Remark VC-240 VC-241 00 to 0F 10 Fixed data-1 11 (Initialized data) 12 80 80 36MHz origin osc adj. *1 54/66MHz origin osc adj. *2 13 80 80 Zoom center adj. 14 Fixed data-1 (Initialized data) 15 16 17 81 81 HALL adj. 18 5D A0 19 17 17 1A 70 *3 HALL adj. *2 1B 62 *3 1C 8D *3 1D 80 9A Max gain adj. 1E 80 80 AWB & LV standard data input 1F 7A 7A 20 Fixed data-1 21 (Initialized data) 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 90 90 AWB & LV standard data input 31 3E 3E 32 43 43 33 59 59 34 Fixed data-1 35 22 22 Color reproduction adj. 36 Fixed data-1 37 27/24 27/24 Color reproduction adj. *4 *4
5-16
Remark Fixed data-1 (Initialized data)
Color reproduction adj.
Fixed data-1 Auto white balance adj. Fixed data-1 (Initialized data)
Flange back adj.
Flange back adj. *1 MR adj. *2 MR adj. *2
Flange back adj.
Flange back adj. *2 Fixed data-1 (Initialized data) Angular velocity sensor sensitivity adj.
Fixed data-1 Optical axis adj. *1 Fixed data-1 (Initialized data)
Address Initial value *5 VC-240 VC-241 6C 00 00 6D 00 00 6E 00 00 6F 70 81 C4 71 0B 0E 72 94 75 73 09 0C 74 66 26 75 08 0B 76 84 35 77 07 0A 78 9B 6E 79 05 09 7A 25 A5 7B 43 61 7C 44 A1 7D 4A 79 7E 44 64 7F 47 81 80 52 82 81 3F 84 82 44 B5 83 30 7B 84 21 20 85 86 87 88 89 8A 8B 8C 02 *3 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 to AF B0
00 00
*3 *6
Address Initial value *5 VC-240 VC-241 B1 B2 to B3 B4 B5 to BB BC BD to D0 D1 D2 to D4 D5 D6 to DC DD DE to FF
Remark IR video carrier freq. Adj. IR video deviation Adj. IR audio deviation Adj. Fixed data-1 Mechanical shutter adj.
Remark Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)
Table. 5-1-7.
Fixed data-1 (Initialized data)
Max gain adj. *2 Fixed data-1 Fixed data-2 (Copy the data built in the same model.) Fixed data-1 (Initialized data)
Max gain adj. *2 *6: Fixed data-2 Fixed data-1 Fixed data-2
5-17
4. E Page Table Address Initial value *5 VC-240 VC-241 78 79 to 7E 7F 80 to 83 84 85 86 87 88 to 8B 8C 8D to 8E 8F 90 91 92 93 to 94
Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”.) Note2: Refer to “2. Modification of E, F, 7 Page Data” for the camera microprocessor version.
*1: *2: *3: *4: *5:
Camera microprocessor ver. 1.0 Camera microprocessor ver. 2.0 or later Fixed data-1 DCR-TRV6/TRV6E/TRV11/TRV11E model only VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E
Address Initial value *5 Remark VC-240 VC-241 00 to 02 Fixed data-1 (Initialized data) 03 Fixed data-2 04 to 11 Fixed data-1 (Initialized data) 12 Fixed data-2 13 Fixed data-1 (Initialized data) 14 15 Fixed data-2 16 to 1A Fixed data-1 (Initialized data) 1B Fixed data-2 1C Fixed data-1 1D Fixed data-2 1E to 38 Fixed data-1 39 Fixed data-2 3A 3B to 3C Fixed data-1 3D Fixed data-2 3E to 49 Fixed data-1 (Initialized data) 4A 63 *1 *3 *1: Camera microprocessor ver. 1.0 83 *2 *2: Camera microprocessor ver. 2.0 or later *3: Fixed data-1 4B to 4F Fixed data-1 (Initialized data) 50 Fixed data-2 51 to 63 Fixed data-1 (Initialized data) 64 Fixed data-2 65 66 to 69 Fixed data-1 6A Fixed data-2 6B to 6D Fixed data-1 6E Fixed data-2 6F to 70 Fixed data-1 71 Fixed data-2 72 (Modified data. Copy the data built in the same model.) 73 74 75 to 77 Fixed data-1 (Initialized data)
95 96 97 98 99 to A1 A2 A3 to AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB to CE CF D0
*3
D1 to DD DE DF to FF
*3
Remark Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2
Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2
Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.)
Fixed data-1 Fixed data-2 26/24 Optical axis adj. *4 *6 *6: NTSC/PAL Fixed data-1 (Initialized data) 5F/71 Optical axis adj.*4 *6 *6: NTSC/PAL Fixed data-1 (Initialized data)
Table. 5-1-8.
5-18
5. 7 Page Table Address Initial value *1 Remark VC-240 VC-241 AA Fixed data-2 (Note2) (Note3) AB (Modified data. Copy the data built in the same model.) AC AD AE AF B0 B1 B2 B3 B4 B5
Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 7 Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 7 Page Data”). Note2: Addresses: 5A to B5 are only for DCR-TRV20/TRV20E model. Note3: Addresses: A4 to B5 are only for the camera microprocessor version 2.0 or later.
*1: VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E Address Initial value *1 Remark VC-240 VC-241 00 Fixed data-2 01 to 03 Fixed data-1 (Initialized data) 04 Fixed data-2 05 (Modified data. Copy the data built in the same model.) 06 07 08 09 to 15 Fixed data-1 (Initialized data) 16 Fixed data-2 17 (Modified data. Copy the data built in the same model.) 18 19 1A 1B Fixed data-1 1C Fixed data-2 (Modified data. Copy the data built in 1D the same model.) 1E 1F 20 21 to 22 Fixed data-1 23 7A 7C Mechanical shutter adj. 24 80 7F 25 80 7C 26 82 7B 27 to 3C Fixed data-1 (Initialized data) 3D Fixed data-2 3E to 44 Fixed data-1 (Initialized data) 45 Fixed data-2 46 to 51 Fixed data-1 52 Fixed data-2 53 54 to 59 Fixed data-1 5A to 84 Fixed data-1 (Note2) 85 Fixed data-2 (Note2) 86 to A3 Fixed data-1 (Note2) (Initialized data) A4 Fixed data-2 (Note2) (Note3) (Modified data. Copy the data built in A5 the same model.) A6 A7 A8 A9
Table. 5-1-9.
5-19
1-3.
CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. Note: NTSC model: DCR-TRV6/TRV11/TRV20 PAL model: DCR-TRV6E/TRV11E/TRV20E
2. 54MHz/66MHz Origin Oscillation Adjustment (DCR-TRV20/TRV20E) (CD-252 board) Set the frequency of the clock for synchronization. If deviated, the synchronization will be disrupted and the color will become inconsistent.
1. 36MHz Origin Oscillation Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) (VC-241 board) Set the frequency of the clock for synchronization. If deviated, the synchronization will be disrupted and the color will become inconsistent. Subject Not required
Subject Measurement Point
Not required Pin qh of IC701 of VC-240 board or pin 7 of IC1901 of VC-240 board
Measurement Point Measuring Instrument
Pin qh of IC701 or pin 7 of IC1901 Frequency counter
Adjustment Page Adjustment Address
F 12
Measuring Instrument Adjustment Page
Frequency counter F
Specified Value
Pin qh of IC701: f=18000000 ± 90Hz Pin 7 of IC1901: f=3579545 ± 18Hz (Note)
Adjustment Address Specified Value
12 Pin qh of IC701 of VC-240 board : f=33000000 ± 165Hz (NTSC) f=27000000 ± 134Hz (PAL) Pin 7 of IC1901 of VC-240 board: f=3579545 ± 18Hz (Note)
Note: SUPER LASER LINK ................................... ON (Red LED is lit)
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: F, address: 12, change the data and set the clock frequency (f) to the specified value. 3) Press the PAUSE button of the adjustment remote commander. 4) Select page: 0, address: 01, and set data: 00.
25 12
1 36
13
Note: SUPER LASER LINK ................................... ON (Red LED is lit)
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: F, address: 12, change the data and set the clock frequency (f) to the specified value. 3) Press the PAUSE button of the adjustment remote commander. 4) Select page: 0, address: 01, and set data: 00.
VC-240/241 board
24 13 12
IC701 1
48 37 48
24
37 25
36
IC1901
Fig. 5-1-6.
5-20
4. HALL Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) For detecting the position of the lens iris, adjust AMP gain and offset. Subject Not required
3. Zoom Key Center Adjustment Set the A/D value center of the microprocessor to the center voltage of the zoom key. If deviated, the zoom lens operates of itself, even if the zoom key is the center position. Subject Not required Measurement Point Measuring Instrument
Display data of page: 6, address: 50 Adjustment remote commander
Adjustment Page Adjustment Address
F 13
Note: Don’t touch the zoom lever during adjustment.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 50, read the data, and this data is named D50. 3) Select page: F, address: 13, set data: D50. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 0, address: 01, and set data: 00.
Measurement Point Measuring Instrument
Display data of page 1 (Note1) Adjustment remote commander
Adjustment Page Adjustment Address
F 17, 18, 19
Specified Value
When the data of page: 6, address: 01 is “01”: 15 to 19 (Note2) When the data of page: 6, address: 01 is “03”: 87 to 8B (Note2)
Note1: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX IRIS display data Note2: The PAUSE button of the Adjustment remote commander must be pressed.
Switch setting: POWER .................................................................. CAMERA Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 94, and set data: 17. 3) Select page: 6, address: 95, and set data: 89. 4) Select page: 6, address: 01, set data: 6D, and press the PAUSE button of the adjustment remote commander. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 17 to 19.) 5) Select page: 6, address: 02, and check that the data is “01”. 6) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Checking method: 1) Select page: 6, address: 04, and set data: 03. 2) Select page: 6, address: 01, set data: 01, and press the PAUSE button. 3) Select page: 1, and check that the IRIS display data (Note1) satisfies the specified value. 4) Select page: 6, address: 01, set data: 03, and press the PAUSE button. 5) Select page: 1, and check that the IRIS display data (Note1) satisfies the specified value. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 04, and set data: 00. 3) Select page: 6, address: 94, and set data: 00. 4) Select page: 6, address: 95, and set data: 00. 5) Select page: 0, address: 01, and set data: 00.
5-21
5. HALL Adjustment (DCR-TRV20/TRV20E) For detecting the position of the lens iris and ND filter, adjust each AMP gain and offset. Subject Not required Measurement Point Measuring Instrument
Display data of page 1 (Note1) Adjustment remote commander
Adjustment Page Adjustment Address
F 17, 18, 19, 1A, 1B, 1C
Specified Value
When the data of page: 6, address: 01 is “01”: 15 to 19 (Note2) When the data of page: 6, address: 01 is “03”: 87 to 8B (Note2) When the data of page: 6, address: 01 is “69”: 87 to 8B (Note2) When the data of page: 6, address: 01 is “6B”: 15 to 19 (Note2)
6. MR Adjustment (DCR-TRV20/TRV20E) The MR (Magnet resistor) adjustment of the inner focus lens is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. Subject Not required Measurement Point Measuring Instrument
Adjustment remote commander
Adjustment Page Adjustment Address
F 50 to 59, 62
Specified Value
40 to C0 (Address: 50) 40 to C0 (Address: 51) 03 to 78 (Address: 52, 54, 56, 58) 88 to F8 (Address: 53, 55, 57, 59)
Note: Make the lens horizontal and perform this adjustment.
Switch setting: POWER .................................................................. CAMERA
Note1: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX IRIS display data ND display data Note2: The PAUSE button of the Adjustment remote commander must be pressed.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 01, set data: BD, and press the PAUSE button of the adjustment remote commander. (The MR adjustment is performed and the adjustment data is stored in page: F, address: 50 to 59, 62.) 3) Select page: 6, address: 02, and check that the data is “01”. 4) Select page: F, address: 50, and check that the data satisfies the specified value. 5) Select page: F, address: 51, and check that the data satisfies the specified value. 6) Select page: F, address: 52, 54, 56 and 58, and check that the data satisfies the specified value. 7) Select page: F, address: 53, 55, 57 and 59, and check that the data satisfies the specified value.
Switch setting: POWER .................................................................. CAMERA Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 94, and set data: 17. 3) Select page: 6, address: 95, and set data: 89. 4) Select page: 6, address: 01, set data: 6D, and press the PAUSE button of the adjustment remote commander. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 17 to 1C.) 5) Select page: 6, address: 02, and check that the data is “01”. 6) Select page: 6, address: 01, set data: 00, and press the PAUSE button.
Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 0, address: 01, set data: 00. 3) Turn off the power and turn on again. 4) Perform “Flange Back Adjustment”.
Checking method: 1) Select page: 6, address: 04, and set data: 03. 2) Select page: 6, address: 01, set data: 01, and press the PAUSE button. 3) Select page: 1, and check that the IRIS display data (Note1) satisfies the specified value. 4) Select page: 6, address: 01, set data: 03, and press the PAUSE button. 5) Select page: 1, and check that the IRIS display data (Note1) satisfies the specified value. 6) Select page: 6, address: 01, set data: 69, and press the PAUSE button. 7) Select page: 1, and check that the ND display data (Note1) satisfies the specified value. 8) Select page: 6, address: 01, set data: 6B, and press the PAUSE button. 9) Select page: 1, and check that the ND display data (Note1) satisfies the specified value. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 04, and set data: 00. 3) Select page: 6, address: 94, and set data: 00. 4) Select page: 6, address: 95, and set data: 00. 5) Select page: 0, address: 01, and set data: 00.
5-22
7. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. Subject Siemens star chart with ND filter for the minipattern box (Note2) Measurement Point Measuring Instrument
Check operation on TV monitor
Adjustment Page Adjustment Address
F DCR-TRV6/TRV6E/TRV11/TRV11E: 13, 4A to 51, 5A to 62 DCR-TRV20/TRV20E: 13, 4A to 4F, 5A to 63
Adjusting method: 1) Install the minipattern box so that the distance between it and the front of the lens of the camcorder is less than 3cm. 2) Make the height of the minipattern box and the camcorder equal. 3) Check that the output voltage of the regulated power supply is the specified voltage. 4) Check that at both the zoom lens TELE end and WIDE end, the center of the Siemens star chart and center of the exposure screen coincide. 5) Select page: 0, address: 01, and set data: 01. 6) Select page: 6, address: 02, and check that the data is “00”. 7) Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander. Note: Don’t touch the zoom lever. If you touch the zoom lever, the zoom center adjustment data will be rewritten in the value which isn’t correct.
Note1: Perform this adjustment after performing “HALL Adjustment” and “MR Adjustment (DCR-TRV20/TRV20E)”. Note2: Dark Siemens star chart.
8)
Select page: 6, address: 01, set data: 27, and press the PAUSE button. (The adjustment data will be automatically input to the adjustment addresses.) 9) Select page: 6, address: 02, and check that the data is “01”. 10) Only for DCR-TRV20/TRV20E model, select page: F, address: 63, and check that the data is “00” to “0E”.
Switch setting: POWER .................................................................. CAMERA NIGHT SHOT .................................................................. OFF Preparations before adjustments: The minipattern box is installed as shown in the following figure.
Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 0, address: 01, and set data: 00. 3) Turn off the power and turn on again. 4) Perform “Flange Back Check”.
Note: The attachment lenses are not used.
Specified voltage: The specified voltage varies according to the minipattern box, so adjust the power supply output voltage to the specified voltage written on the sheet which is supplied with the minipattern box. Below 3 cm Minipattern box Camcorder Camera table Regulated power supply Output voltage : Specified voltage ±0.01Vdc Output current : more than 3.5A
Red (+) Black (–) Yellow (SENS +) White (SENS –)
Need not connected
Black (GND)
Fig. 5-1-7.
5-23
8. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 8-1. Flange Back Adjustment (1) Perform this adjustment after performing “HALL Adjustment” and “MR Adjustment (DCR-TRV20/TRV20E)”. Subject Flange back adjustment chart (2.0 m from the front of the lens) (Luminance: 350 ± 50 lux)
8-2. Flange Back Adjustment (2) Perform this adjustment after performing “Flange Back Adjustment (1)”. Subject Subject more than 500m away (Subjects with clear contrast such as buildings, etc.)
Measurement Point Measuring Instrument
Check operation on TV monitor
Measurement Point Measuring Instrument
Check operation on TV monitor
Adjustment Page Adjustment Address
F DCR-TRV6/TRV6E/TRV11/TRV11E: 13, 4A to 51, 5A to 62 DCR-TRV20/TRV20E: 13, 4A to 4F, 5A to 63
Adjustment Page Adjustment Address
F DCR-TRV6/TRV6E/TRV11/TRV11E: 13, 4A to 51, 5A to 62 DCR-TRV20/TRV20E: 13, 4A to 4F, 5A to 63
Switch setting: POWER .................................................................. CAMERA NIGHT SHOT .................................................................. OFF
Switch setting: POWER .................................................................. CAMERA NIGHT SHOT .................................................................. OFF
Adjusting method: 1) Check that at both the zoom lens TELE end and WIDE end, the center of the chart for the flange back adjustment and center of the exposure screen coincide. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 6, address: 02, and check that the data is “00”. 4) Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander. 5) Select page: 6, address: 01, set data: 15, and press the PAUSE button. (The adjustment data will be automatically input to the adjustment addresses.) 6) Select page: 6, address: 02, and check that the data is “01”. 7) Only for DCR-TRV20/TRV20E model, select page: F, address: 63, and check that the data is “00” to “0E”.
Adjusting method: 1) Set the zoom lens to the TELE end and expose a subject that is more than 500 m away (subject with clear contrast such as building, etc.). (Nearby subjects less than 500 m away should not be in the screen.) 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 6, address: 02, and check that the data is “00”. 4) Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander. Note: Don’t touch the zoom lever. If you touch the zoom lever, the zoom center adjustment data will be rewritten in the value which isn’t correct.
5) 6)
Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Turn off the power and turn on again. 3) Perform “Flange Back Adjustment (2)”.
7)
Place a ND filter on the lens so that the optimum image is obtain. Select page: 6, address: 01, set data: 29, and press the PAUSE button. (The adjustment data will be automatically input to the adjustment addresses.) Select page: 6, address: 02, and check that the data is “01”.
Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 0, address: 01, and set data: 00. 3) Turn off the power and turn on again. 4) Perform “Flange Back Check”.
5-24
9. Flange Back Check Subject Siemens star (2.0m from the front of the lens) (Luminance : approx. 200 lux) Measurement Point Measuring Instrument
Check operation on TV monitor
Specified Value
Focused at the TELE end and WIDE end.
Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF 4) STEADY SHOT (Menu display) ..................................... OFF Note: When the auto focus is ON, the lens can be checked if it is focused or not by observing the data on the page 1 of the adjustment remote commander. 1) Select page: 6, address: 04, and set data: 0F. 2) Page 1 shows the state of the focus. 1 : 00 : XX Focused [ Odd: Even: Unfocused
Checking method: 1) Place the Siemens star 2.0m from the front of the lens. 2) To open the IRIS, decrease the luminous intensity to the Siemens star up to a point before noise appear on the image. 3) Shoot the Siemens star with the zoom TELE end. 4) Turn on the auto focus. 5) Check that the lens is focused (Note). 6) Select page: 6, address: 21, and set data: 10. 7) Shoot the Siemens star with the zoom WIDE end. 8) Observe the TV monitor and check that the lens is focused. Processing after Completing Adjustments: 1) Select page: 6, address: 21, and set data: 00. 2) Select page: 6, address: 04, and set data: 00.
5-25
10. Optical Axis Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) Align the lens Optical Axis with that of the CCD imager. If deviated, center of picture can lose focus when zoom is operated from the WIDE end to the TELE end. Subject Siemens star Measurement Point Measuring Instrument
Check on the monitor TV
Adjustment Page Adjustment Address
F 69
Note: NTSC model: DCR-TRV6/TRV11 PAL model: DCR-TRV6E/TRV11E
Area
1
E D0, DE
2
Switch setting: 1) POWER .................................................................. CAMERA
3
Preparations before adjustments: 1) Playback the monoscope segment of the system check tape (XH5-5 (NTSC), XH5-5P (PAL)). 2) Attach the optical axis frame chart (transparent) on the monitor TV screen. Center of monoscope image and that that of optical axis frame must be agree. 3) Set to the camera mode.
4 5 6 7
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 40, and set data: 02. 3) Select page: 6, address: 41, and set data: 01. 4) Input the data of Table 5-1-9 to each adjustment addresses.
8
00
22.6° to 67.5° 67.6° to 112.5° 112.6° to 157.5° 157.6° to 202.5° 202.6° to 247.5° 247.6° to 292.5° 292.6° to 337.5° 337.6° to 22.5°
Connection data Page: F Page: E Address: 69 Address: D0 Address: DE NTSC PAL NTSC PAL 01 22 26 57 69 02
22
26
5F
71
03
22
26
67
79
04
02
26
69
7D
05
22
26
67
79
06
22
26
5F
71
07
22
26
57
69
08
02
26
55
65
Table. 5-1-11.
Note: Press the PAUSE button each time to set the data.
Page: F Address: 69
Display phase
Processing after Completing Adjustments: 1) Select page: 0, address: 01, and set data: 00. 2) Select page: 6, address: 40, and set data: 00. 3) Select page: 6, address: 41, and set data: 00.
Page: E Address: D0 Address: DE NTSC PAL NTSC PAL 22 26 5F 71
Table. 5-1-10. 5) 6) 7)
Place the Siemens star 2.0 m away from the front of the lens. Shoot the Siemens star with the zoom TELE end. Point the lens toward the Siemens star chart until center of the Siemens star is located in the center of the optical axis frame. 8) Shoot the Siemens star with the zoom WIDE end. 9) Measure on the monitor TV screen in which area of the optical axis frame the center of the Siemens star is located. Measure the amount of displacement (distance between the center of the Siemens star and the center of the optical axis frame.) The measurement value is named L1. 10) Read the correction data corresponding to the area from Table 5-1-10. 11) Input the correction data to each adjustment address. Note: Press the PAUSE button each time to set the data.
12) Shoot the Siemens star with the zoom TELE end. 13) Point the lens toward the Siemens star chart until center of the Siemens star is located in the center of the optical axis frame. 14) Shoot the Siemens star with the zoom WIDE end. 15) Measure the amount of displacement (distance between the center of the Siemens star and the center of the optical axis frame.) The measurement value is named L2. 16) Compare the values L1 and L2, and confirm that L2 is smaller than L1. If L2 is lager than L1, input the data of Table 5-1-9 to each adjustment address.
Fig. 5-1-8.
Note: Press the PAUSE button each time to set the data.
5-26
11. Picture Frame Setting Subject Color bar chart (Color reproduction adjustment frame) (1.5m from the front of the lens) Measurement Point Measuring Instrument
Video output terminal Oscilloscope and TV monitor
Specified Value
A=B, C=D, E=F
Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF 4) STEADY SHOT (Menu display) ..................................... OFF Setting method: 1) Adjust the zoom and the camera direction, and set to the specified position. 2) Mark the position of the picture frame on the monitor display, and adjust the picture frame to this position in following adjustments using “Color reproduction adjustment frame”.
Check on the oscilloscope 1. Horizontal period A=B
C=D
B
C
A
D
Fig. 5-1-9. 2. Vertical period E=F
E
F
V
Fig. 5-1-10. Check on the monitor TV (Underscanned mode)
Color bar chart picture frame
Monitor TV picture frame
Fig. 5-1-11.
5-27
12. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. Subject Color bar chart (Color reproduction adjustment frame) Measurement Point Measuring Instrument
Video output terminal Vectorscope
Adjustment Page Adjustment Address
F 35, 37, 3C, 3D
Specified Value
All color luminance points should settle within each color reproduction frame.
For DCR-TRV6/TRV11 (NTSC)
Note: NTSC model: DCR-TRV6/TRV11/TRV20 PAL model: DCR-TRV6E/TRV11E/TRV20E
Burst position
For DCR-TRV6E/TRV11E (PAL)
Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF 4) STEADY SHOT (Menu display) ..................................... OFF
Burst position
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: F, address: 8E, set the following data and press the PAUSE button. 29: DCR-TRV6/TRV6E/TRV11/TRV11E 14: DCR-TRV20/TRV20E 3) Select page: F, address: C0, set the following data and press the PAUSE button. 37: NTSC model B7: PAL model 4) Select page: 6, address: 01, set data: 3D, and press the PAUSE button. 5) Adjust the GAIN and PHASE of the vectorscope, and adjust the burst luminance point to the burst position of the color reproduction frame. 6) Change the data of page: F, address: 35, 37, 3C and 3D, and settle each color luminance point in each color reproduction frame.
For DCR-TRV20 (NTSC)
Note: Be sure to press the PAUSE button of the adjustment remote commander before changing the addresses. If not, the new data will not be written to the memory.
Processing after Completing Adjustments: 1) Select page: F, address: 8E, set the following data, and press the PAUSE button. 2E: DCR-TRV6/TRV6E/TRV11/TRV11E 17: DCR-TRV20 14: DCR-TRV20E 2) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00.
Burst position
For DCR-TRV20E (PAL) Burst position
Fig. 5-1-12.
5-28
14. Auto White Balance & LV Standard Data Input Subject Clear chart (Color reproduction adjustment frame)
13. MAX GAIN Adjustment Setting the minimum illumination. If it is not consistent, the image level required for taking subjects in low illuminance will not be produced (dark). 13-1. MAX GAIN Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) Subject Clear chart (Color reproduction adjustment frame) Adjustment Page Adjustment Address
F 1D
F 1E, 1F, 30 to 33
Specified Value
0FF0 to 1010
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 01, set data: 11, and press the PAUSE button of the adjustment remote commander. 3) Select page: 6, address: 01, set data: 0D, and press the PAUSE button. (When the standard data is take in, the data will be automatically input to page: F, address: 1E, 1F, 30 to 33.) 4) Select page: 6, address: 02, and check that the data is “01”. 5) Select page: F, address: 10, set data: 2E, and press the PAUSE button. 6) Select page: 1, and check that the display data (Note3) satisfies the specified value.
Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 97, and set data: 00. 3) Select page: 0, address: 01, and set data: 00.
13-2. MAX GAIN Data Input (DCR-TRV20/TRV20E) Adjustment Page F
Processing after Completing Adjustments: 1) Select page: F, address: 10, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00. 4) Perform “Auto White Balance Adjustment”.
1D, 8C, 9E, 9F
Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Input the following data to each address. Note: Press the PAUSE button of the adjustment remote commander each time to set the data.
3)
Adjustment Page Adjustment Address
Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 96, and set data: 00. 3) Select page: 6, address: 97, and set data: 27. 4) Select page: 6, address: 01, set data: 6F, and press the PAUSE button of the adjustment remote commander. (The MAX GAIN adjustment is performed and the adjustment data is stored in page: F, address: 1D.) 5) Select page: 6, address: 02, and check that the data is “01”.
Address 1D 8C 9E 9F
Display data of page 1 (Note3) Adjustment remote commander
Note1: This adjustment should be carried out upon completion of “Color Reproduction Adjustment”. Note2: Check that the data of page: 6, address: 02 is “00”. If not, turn off the power and turn on again. Note3: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX Display data
Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) STEADY SHOT (Menu display) ..................................... OFF
Adjustment Address
Measurement Point Measuring Instrument
Data 80 02 00 00
Select page: 0, address: 01, and set data: 00.
5-29
15. Auto White Balance Adjustment Adjust to the proper auto white balance output data. If it is not correct, auto white balance and color reproducibility will be poor. Subject Clear chart (Color reproduction adjustment frame) Filter Measurement Point
Filter C14 for color temperature correction Display data of page 1 (Note2)
Measuring Instrument Adjustment Page
Adjustment remote commander F
Adjustment Address Specified Value
40, 41 DCR-TRV6/TRV11: R ratio: 2B00 to 2C00 B ratio: 5B00 to 5C00 DCR-TRV6E/TRV11E: R ratio: 2D00 to 2E00 B ratio: 5B00 to 5C00 DCR-TRV20/TRV20E: R ratio: 2C30 to 2D30 B ratio: 5F20 to 6020
Note1: Perform “Auto White Balance & LV Standard Data Input” before this adjustment. Note2: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX Display data
Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF
Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 04, and set data: 00. 3) Select page: 0, address: 01, and set data: 00.
Adjusting method: 1) Place the C14 filter for color temperature correction on the lens. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: F, address: 42 to 45, and note down the data of each address. 4) Input the following data to page: F, addresses: 42 to 45. Address 42 43 44 45 Data 2B 80 5B 80 DCR-TRV6/TRV11 2D 80 5B 80 DCR-TRV6E/TRV11E 2C B0 5F A0 DCR-TRV20/TRV20E Note: Press the PAUSE button each time to set the data.
5) 6)
7) 8) 9) 10) 11) 12) 13)
Select page: 6, address: 01, set data: 83, and press the PAUSE button. Select page: 6, address: 01, set data: 81, and press the PAUSE button. (The auto white balance adjustment is performed and the adjustment data is stored in page: F, address: 40 and 41.) Select page: 6, address: 02, and check that the data is “01”. Select page: 6, address: 01, set data: 3F, and press the PAUSE button. Select page: 6, address: 04, and set data: 04. Select page: 1, and check that the display data (Note2) satisfies the R ratio specified value. Select page: 6, address: 04, and set data: 05. Select page: 1, and check that the display data (Note2) satisfies the B ratio specified value. Select page: F, address: 42 to 45, and input the data noted down at step 3). Note: After setting each data, be sure to press the PAUSE button of the adjustment remote commander.
5-30
16. White Balance Check Subject Clear chart (Color reproduction adjustment frame) Filter
Measurement Point
Filter C14 for color temperature correction ND filter 1.0 and 0.4 and 0.1 Video output terminal
Measuring Instrument Specified Value
Vectorscope Fig. 5-1-13. A to C
17. Mechanical Shutter Adjustment Adjust the period which the mechanical shutter is closed, and compensate the exposure. 17-1. Mechanical Shutter Data Input (DCR-TRV6/TRV6E/TRV11/TRV11E) Adjustment Page F 7 Adjustment Address
23 to 26
Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Input the following data to page: F, addresses: 70 to 84.
Switch setting: 1) POWER .................................................................. CAMERA 2) NIGHT SHOT .................................................................. OFF 3) DIGITAL ZOOM (Menu display) ................................... OFF
Note: Press the PAUSE button of the adjustment remote commander each time to set the data.
Address 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84
Checking method: 1) Check that the lens is not covered with either filter. 2) Select page: 6, address: 01, set data: 0F, and press the PAUSE button of the adjustment remote commander. 3) Check that the center of the white luminance point is within the circle shown Fig. 5-1-13. (A). 4) Select page: 6, address: 01, set data: 23, and press the PAUSE button. 5) Place the C14 filter on the lens. 6) Check that the center of the white luminance point settles in the circle shown Fig. 5-1-13. (B). 7) Remove the C14 filter, and place the ND filter 1.5 (1.0+0.4+0.1) on the lens. 8) Check that the white luminance point stopped moving, and then remove the ND filter 1.5. 9) Check that the center of the white luminance point settles within the circle shown Fig. 5-1-13. (C). Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2mm
R-Y
70 to 84
B-Y
3)
Data C4 0E 75 0C 26 0B 35 0A 6E 09 A5 61 A1 79 64 81 82 84 B5 7B 20
Input the following data to page: 7, addresses: 23 to 26. Note: Press the PAUSE button of the adjustment remote commander each time to set the data.
2mm
Address 23 24 25 26
Fig. 5-1-13. (A) R-Y
1.0mm
B-Y 1.0mm
4)
3mm
3mm
Fig. 5-1-13. (B) 3mm
R-Y
3mm 2.0mm B-Y 1.0mm
Fig. 5-1-13. (C)
5-31
Data 7C 7F 7C 7B
Select page: 0, address: 01, and set data: 00.
17-2. Mechanical Shutter Data Input (DCR-TRV20/TRV20E) Adjustment Page F Adjustment Address
70 to 84
18. Angular Velocity Sensor Sensitivity Adjustment • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts. At this time, note down also to which board it was attached to. Be sure to check because if attached incorrectly, the screen will vibrate up and down or left and right during hand-shake correction operations.
7 23 to 26
Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Input the following data to page: F, addresses: 70 to 84. Note: Press the PAUSE button of the adjustment remote commander each time to set the data.
Address 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84 3)
Data 81 0B 94 09 66 08 84 07 9B 05 25 43 44 4A 44 47 52 3F 44 30 21
Precautions on the Parts Replacement There are two types of repair parts. Type A: ENC03JA Type B: ENC03JB Replace the broken sensor with a same type sensor. If replace with other type parts, the image will vibrate up and down or left and right during hand-shake correction operations. After replacing, readjust according to the adjusting method after replacement. Precautions on Angular Velocity Sensor The sensor incorporates a precision oscillator. Handle it with care as if it dropped, the balance of the oscillator will be disrupted and operations will not be performed properly.
66, 67
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Read the sensor sensitivity written on SE3051 (PITCH sensor) of the JK-188 board, and take this as S3051. 3) Read the sensor sensitivity written on SE3052 (YAW sensor) of the JK-188 board, and take this as S3052. 4) Calculate D66' and D67' using the following equation (decimal calculation). DCR-TRV6/TRV11 (NTSC model) D66' = 54 / S3051 D67' = 61 / S3052 DCR-TRV6E/TRV11E (PAL model) D66' = 76 / S3051 D67' = 72 / S3052 DCR-TRV20 (NTSC model) D66' = 53 / S3051 D67' = 53 / S3052 DCR-TRV20E (PAL model) D66' = 60 / S3051 D67' = 60 / S3052 5) Convert D66' and D67' into hexadecimal digits, to obtain D66 and D67. (Round off decimal points) 6) Select page: F, address: 66, set data: D66, and press the PAUSE button of the adjustment remote commander. 7) Select page: F, address: 67, set data: D67, and press the PAUSE button of the adjustment remote commander.
Note: Press the PAUSE button of the adjustment remote commander each time to set the data.
4)
F
Adjustment Address
Note1: The sensor sensitivity of SE3051 and SE3052 of the JK-188 board is written only on the repair parts.
Input the following data to page: 7, addresses: 23 to 26.
Address 23 24 25 26
Adjustment Page
Data 7A 80 80 82
Select page: 0, address: 01, and set data: 00.
Processing after Completing Adjustments 1) Select page: 0, address: 01, and set data: 00. 2) Check that the steady shot operations have been performed normally.
5-32
1-4.
1. VCO Adjustment (VC-240/241 board) Set the VCO free-run frequency. If deviated, the EVF screen will be blurred. Mode Camera
COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT
Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to avoid electrical shock. Note 2: When replacing the LCD unit, be careful to prevent damages caused by static electricity. Note 3: Set the VF BRIGHT (Menu display) to the center. Close the LCD panel. Note 4: As the PANEL CLOSE switch (CK-92/94 board S3201) is attached to the cabinet (R), this cabinet must be attached when performing adjustments. If you perform the adjustments with cabinet (R) removed, set the following data. 1) Select page: 2, address: 0E, and set data: 67. 2) Select page: 2, address: 0F, and set data: 01. Reset the data after completing adjustment. 1) Select page: 2, address: 0E, and set data: 00. 2) Select page: 2, address: 0F, and set data: 00. Note 5: CK-92 board: DCR-TRV11/TRV11E/TRV20 CK-94 board: DCR-TRV6/TRV6E/TRV20E VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E
Signal Name LANC SIG EVF BL – EVF VCO PANEL VG H START PANEL COM TCK JIG TDO SWP GND
Pin No. 2 4 6 8 10 12 14 16 18 20
19
20
Frequency counter D
Adjustment Address Specified Value
92, 93 f = 15734 ± 30Hz (NTSC) f = 15625 ± 30Hz (PAL)
Note: The VCO adjustment mode is set up automatically, so the EVF screen falls into the disorder.
3) 4) 5)
Signal Name EVF BL + EVF VG GND PD VCO XHD/PSIG TMS JIG TDI GND RF IN/LANC JACK IN RF MON
CN009 2
Measuring Instrument Adjustment Page
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 92, change the data and set the VCO frequency (f) to the specified value.
Table. 5-1-12.
1
Arbitrary Pin 5 of CN009 (VCO)
Note: NTSC model: DCR-TRV6/TRV11/TRV20 PAL model: DCR-TRV6E/TRV11E/TRV20E
[Adjusting connector] Most of the measuring points for adjusting the viewfinder system are concentrated in CN009 of the VC-240/241 board. Connect the Measuring Instruments via the CPC-8 jig (J-6082-388-A). The following table shows the Pin No. and signal name of CN009. Pin No. 1 3 5 7 9 11 13 15 17 19
Subject Measurement Point
Remove the CPC lid
Fig. 5-1-14.
5-33
Press the PAUSE button of the adjustment remote commander. Select page: D, address: 93, set the same data as page: D, address: 92, and press the PAUSE button. Select page: 0, address: 01, and set data: 00.
3. Contrast Adjustment (VC-240/241 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). Mode Camera
2. RGB AMP Adjustment (VC-240/241 board) Set the D range of the RGB decoder used to drive the LCD to the specified value. If deviated, the LCD screen will become blackish or saturated (whitish). Mode Camera Subject Measurement Point
Arbitrary Pin 4 of CN009 (EVF VG)
Subject Measurement Point
Arbitrary Pin 4 of CN009 (EVF VG)
Measuring Instrument Adjustment Page
Oscilloscope D
Measuring Instrument Adjustment Page
Oscilloscope D
Adjustment Address Specified Value
95 A = 7.00 ± 0.05V
Adjustment Address Specified Value
99 DCR-TRV20/TRV20E: A=2.40 ± 0.05V DCR-TRV6/TRV6E/TRV11/TRV11E: A=2.20 ± 0.05V
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 95, change the data and set the voltage (A) between the reversed waveform pedestal and non-reversed waveform pedestal to the specified value.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 99, change the data and set the voltage (A) between the pedestal (0 IRE) and 100 IRE to the specified value. (The data of address: 99 should be “00” to “7F”.)
Note: The RGB AMP adjustment mode is set up automatically, so the 3 steps signal is displayed on the EVF screen.
3) 4)
Press the PAUSE button. Select page: 0, address: 01, and set data: 00.
Note: The contrast adjustment mode is set up automatically, so the 3 steps signal is displayed on the EVF screen.
3) 4)
Pedestal
Press the PAUSE button. Select page: 0, address: 01, and set data: 00.
A
100 IRE
A
2H
2H
Pedestal
Pedestal
Fig. 5-1-15.
Fig. 5-1-16.
5-34
5. White Balance Adjustment (VC-240/241 board) Correct the white balance. If deviated, the reproduction of the EVF screen may degenerate. Mode Camera
4. Backlight Consumption Current Adjustment (VC-240/241 board) Set the backlight luminance and color temperature. If deviated, the image may become dark or bright. Mode Camera Subject Measurement Point
Arbitrary + Probe: Pin 2 of CN009 (EVF BL+) − Probe: Pin 3 of CN009 (EVF BL−)
Measuring Instrument Adjustment Page
Digital voltmeter D
Adjustment Address Specified Value
9C, 9D, 9E DCR-TRV20/TRV20E: BRIGHT mode : A=25.0 ± 1.5mVdc NORMAL mode : A=15.0 ± 1.5mVdc DCR-TRV6/TRV6E/TRV11/TRV11E: BRIGHT mode : A=17.0 ± 1.5mVdc NORMAL mode : A=10.0 ± 1.5mVdc
3)
9E 11
6)
97, 98 The EVF screen should not be colored.
3)
9F 1F
97 80
98 80
Check that the EVF screen is not colored. If colored, change the data of page: D, address: 97 and 98 so that the EVF screen is not colored. Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.
Select page: D, address: 9D, change the data and set the voltage difference (A) between Pin 2 of CN009 (EVF BL+) and Pin 3 of CN009 (EVF BL−) to the specified value of BRIGHT mode. (The data of address: 9D should be “C0” to “FF”.)
4)
Press the PAUSE button of the adjustment remote commander. Select page: D, address: 9C, set the same data as page: D, address: 9D, and press the PAUSE button. Select page: D, address: 9E, change the data and set the voltage difference (A) between Pin 2 and Pin 3 to the specified value of NORMAL mode. (The data of address: 9E should be “00” to “1F”.) Note: The backlight consumption current adjustment NORMAL mode is set up automatically.
7) 8)
Adjustment Address Specified Value
Address Data
Note: The backlight consumption current adjustment BRIGHT mode is set up automatically.
4) 5)
D
Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.
Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.
9D E0
Measuring Instrument Adjustment Page
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 97 and 98, set the data to the initial value.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 9C to 9F, and set the data to the initial value.
9C E0
Arbitrary Check on EVF screen
Note: Check the white balance only when replacing the following parts. If necessary, adjust them. 1. LCD panel 2. Light induction plate 3. IC1802
Note1: Perform the adjustment in the following order.
Address Data
Subject Measurement Point
Press the PAUSE button. Select page: 0, address: 01, and set data: 00.
5-35
When address: 97 or 98 is selected, the white balance adjustment mode is set up automatically. Select page: 0, address: 01, and set data: 00.
1-5.
1-5-1.
LCD SYSTEM ADJUSTMENT
Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to avoid electrical shock. Note 2: When replacing the LCD unit, be careful to prevent damages caused by static electricity. Note 3: Set the LCD BRIGHT to the center. Set the LCD COLOR (Menu display) to the center. Note 4: PD-123 board: DCR-TRV11/TRV11E/TRV20 PD-124 board: DCR-TRV6/TRV6E/TRV20E VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E
1. VCO Adjustment (PD-123 board) Set the VCO free-run frequency. If deviated, the LCD screen will be blurred. Mode Camera
[Adjusting connector] Most of the measuring points for adjusting the LCD system are concentrated in CN009 of the VC-240/241 board. Connect the Measuring Instruments via the CPC-8 jig (J-6082-388A). The following table shows the Pin No. and signal name of CN009. Pin No. 1 3 5 7 9 11 13 15 17 19
Signal Name Pin No. LANC SIG 2 EVF BL – 4 EVF VCO 6 PANEL VG 8 H START 10 PANEL COM 12 TCK 14 JIG TDO 16 SWP 18 GND 20 Table. 5-1-13.
2
19
20
Subject Measurement Point
Arbitrary Pin 9 of CN009 (H START) of VC-240/241 board
Measuring Instrument Adjustment Page
Frequency counter D
Adjustment Address Specified Value
A2, A3 f = 15734 ± 30Hz (NTSC) f = 15625 ± 30Hz (PAL)
Note: NTSC: DCR-TRV11/TRV20 PAL: DCR-TRV11E
Signal Name EVF BL + EVF VG GND PD VCO XHD/PSIG TMS JIG TDI GND RF IN/LANC JACK IN RF MON
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A2, change the data and set the VCO frequency (f) to the specified value. Note: The VCO adjustment mode is set up automatically, so the LCD screen falls into the disorder.
3) 4) 5)
CN009 1
LCD SYSTEM ADJUSTMENT (DCR-TRV11/TRV11E/TRV20)
Remove the CPC lid
Fig. 5-1-17.
5-36
Press the PAUSE button of the adjustment remote commander. Select page: D, address: A3, set the same data as page: D, address: A2, and press the PAUSE button. Select page: 0, address: 01, and set data: 00.
3. Contrast Adjustment (PD-123 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). Mode Camera
2. RGB AMP Adjustment (PD-123 board) Set the D range of the RGB decoder used to drive the LCD to the specified value. If deviated, the LCD screen will become blackish or saturated (whitish). Mode Camera Subject Measurement Point
Arbitrary Pin 7 of CN009 (PANEL VG) of VC-240/241 board Ext. trigger: Pin qa of CN009 (PANEL COM)
Subject Measurement Point
Arbitrary Pin 7 of CN009 (PANEL VG) of VC-240/241 board Ext. trigger: Pin qa of CN009 (PANEL COM)
Measuring Instrument Adjustment Page
Oscilloscope D
Measuring Instrument Adjustment Page
Oscilloscope D
Adjustment Address Specified Value
A5 A = 3.70 ± 0.05V (LCD TYPE SH NTSC) A = 3.45 ± 0.05V (LCD TYPE SH PAL) A = 3.50 ± 0.05V (LCD TYPE CA)
Adjustment Address Specified Value
AA A = 3.30 ± 0.05V (LCD TYPE SH NTSC) A = 3.25 ± 0.05V (LCD TYPE SH PAL) A = 3.45 ± 0.05V (LCD TYPE CA)
Note: LCD TYPE SH NTSC: DCR-TRV11 LCD TYPE SH PAL: DCR-TRV11E LCD TYPE CA: DCR-TRV20
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: AA, change the data and set the voltage (A) between the pedestal (0 IRE) and 100 IRE to the specified value. (The data of address: AA should be “00” to “7F”.)
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A5, change the data and set the voltage (A) between the reversed waveform pedestal and non-reversed waveform pedestal to the specified value. (The data of address: A5 should be “00” to “3F”.)
Note: The contrast adjustment mode is set up automatically, so the 3 steps signal is displayed on the LCD screen.
3) 4)
Press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.
Note: The RGB AMP adjustment mode is set up automatically, so the 3 steps signal is displayed on the LCD screen.
3) 4)
Press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00. Pedestal
100IRE
A
A
2H
2H
Pedestal
Pedestal
Fig. 5-1-18.
Fig. 5-1-19.
5-37
Ver 1.1 2000. 06
4. V-COM Level Adjustment (PD-123 board) Set the common electrode drive signal level of LCD to the specified value. Mode Camera Subject Measurement Point
5. V-COM Adjustment (PD-123 board) Set the DC bias of the common electrode drive signal of LCD to the specified value. If deviated, the LCD display will move, producing flicker and conspicuous vertical lines. Mode Camera
Arbitrary Pin qa of CN009 (PANEL COM) of VC-240/241 board
Measuring Instrument Adjustment Page
Oscilloscope D
Adjustment Address Specified Value
A7 A = 6.00 ± 0.05V (LCD TYPE SH) A = 5.70 ± 0.05V (LCD TYPE CA)
Arbitrary Check on LCD display
Measuring Instrument Adjustment Page
D
Adjustment Address Specified Value
Note: Perform “RGB AMP Adjustment” and “Contrast Adjustment” before this adjustment.
A4 The brightness difference between the section A and section B is minimum.
Note: Perform “RGB AMP Adjustment”, “Contrast Adjustment” and “VCOM Level Adjustment” before this adjustment.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A7, change the data and set the PANEL COM signal level (A) to the specified value.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A4, change the data so that the brightness of the section A and that of the section B is equal.
Note: The V-COM level adjustment mode is set up automatically.
3) 4)
Subject Measurement Point
Press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.
Note: The V-COM adjustment mode is set up automatically, so the V COM adjustment signal is displayed on the LCD screen.
3) 4)
A
2H
Subtract 8 from the data of page: D, address: A4, and press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.
B
A
A
B
B
A
A
B
Fig. 5-1-20. Fig. 5-1-21.
5-38
1-5-2.
6. White Balance Adjustment (PD-123 board) Correct the white balance. If deviated, the reproduction of the LCD screen may degenerate. Mode Camera Subject Measurement Point
Arbitrary Check on LCD screen
Measuring Instrument Adjustment Page
D
Adjustment Address Specified Value
A8, A9 The LCD screen should not be colored.
1. VCO Adjustment (PD-124 board) Set the VCO free-run frequency. If deviated, the LCD screen will be blurred. Mode VTR stop
Note: Check the white balance only when replacing the following parts. If necessary, adjust them. 1. LCD panel 2. Light induction plate 3. IC2104
3)
Measuring Instrument Adjustment Page
Frequency counter D
Adjustment Address Specified Value
A2, A3 f = 15734 ± 30Hz (NTSC) f = 15625 ± 30Hz (PAL)
Note: The VCO adjustment mode is set up automatically, so the LCD screen falls into the disorder.
A9 87
3) 4)
Check that the LCD screen is not colored. If colored, change the data of page: D, address: A8 and A9 so that the LCD screen is not colored.
5)
Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data. When address: A8 or A9 is selected, the white balance adjustment mode is set up automatically.
4)
No signal Pin 9 of CN009 (H START) of VC-240/241 board
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A2, change the data and set the VCO frequency (f) to the specified value.
Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.
A8 7F
Signal Measurement Point
Note: NTSC: DCR-TRV6 PAL: DCR-TRV6E/TRV20E
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A8 and A9, set the data to the initial value.
Address Data
LCD SYSTEM ADJUSTMENT (DCR-TRV6/TRV6E/TRV20E)
6)
Select page: 0, address: 01, and set data: 00.
7) 8)
5-39
Press the PAUSE button of the adjustment remote commander. Select page: D, address: A2, read the data, and this data is named DA2. Convert DA2 to decimal notation, and obtain DA2'. (Refer to Table 5-4-1. Hexadecimal-decimal Conversion Table.) Calculate DA3' using following equations (Decimal calculation), convert it to a hexadecimal number, and input to address: A3. DCR-TRV6: DA3' = DA2' + 38 DCR-TRV6E: DA3' = DA2' - 38 DCR-TRV20E: DA3' = DA2' - 11 Press the PAUSE button. Select page: 0, address: 01, and set data: 00.
2. Bright Adjustment (PD-124 board) Set the D range of the RGB decoder used to drive the LCD to the specified value. If deviated, the LCD screen will become blackish or saturated (whitish). Mode VTR stop
3. Black Limit Adjustment (PD-124 board) Set the dynamic range of the LCD driver to an appropriate level. If deviated, the LCD screen will become blackish or saturated (whitish). Mode VTR stop
Signal Measurement Point
No signal Pin 7 of CN009 (PANEL VG) of VC-240/241 board
Signal Measurement Point
No signal Pin 0 of CN009 (PSIG) of VC-240/241 board
Measuring Instrument Adjustment Page
Oscilloscope D
Measuring Instrument Adjustment Page
Oscilloscope D
Adjustment Address Specified Value
A5 A = 7.6 ± 0.05V
Adjustment Address Specified Value
A6 A = 8.00 ± 0.05V
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 0C, set data: 20, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 22, set data: 08, and press the PAUSE button. 4) Select page: D, address: A5, change the data and set the voltage (A) between the reversed waveform pedestal and non-reversed waveform pedestal to the specified value. 5) Press the PAUSE button. 6) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 7) Select page: 3, address: 22, set data: 00, and press the PAUSE button. 8) Select page: 0, address: 01, and set data: 00.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 0E, and set data: 61. 3) Select page: 2, address: 0F, and set data: 5B (*1) or 53 (*2). *1: DCR-TRV6 *2: DCR-TRV6E/TRV20E 4) Select page: D, address: A6, change the data and set the PSIG signal amplitude (A) to the specified value. (The data of address: A6 should be “00” to “0F”.) 5) Press the PAUSE button of the adjustment remote commander. 6) Select page: 2, address: 0E, and set data: 00. 7) Select page: 2, address: 0F, and set data: 00. 8) Select page: 0, address: 01, and set data: 00.
Pedestal
A
A
V
Fig. 5-1-23. 2H Pedestal
Fig. 5-1-22.
5-40
5. Center Level Adjustment (PD-124 board) Set the video signal center level of LCD panel to an appropriate level. Mode VTR stop
4. Contrast Adjustment (PD-124 board) Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated (whitish). Mode VTR stop Signal Measurement Point
No signal Pin 7 of CN009 (PANEL VG) of VC-240/241 board Ext. trigger: Pin qa of CN009 (PANEL COM)
Measuring Instrument Adjustment Page
Oscilloscope D
Adjustment Address Specified Value
AA A = 2.80 ± 0.05V (TRV6E/TRV20E) A = 2.60 ± 0.05V (TRV6)
No signal Pin 7 of CN009 (PANEL VG) of VC-240/241 board
Measuring Instrument Adjustment Page
Digital voltmeter D
Adjustment Address Specified Value
AB A = 5.25 ± 0.03V (3.5" LCD) A = 6.75 ± 0.03V (2.5" LCD)
Note: 3.5" LCD: DCR-TRV20E 2.5" LCD: DCR-TRV6/TRV6E
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 0C, set data: 20, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 22, set data: 08, and press the PAUSE button. 4) Select page: D, address: AB, change the data and set the DC voltage (A) of VG signal to the specified value. 5) Press the PAUSE button. 6) Select page: 3, address: 22, set data: 00, and press the PAUSE button. 7) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 8) Select page: 0, address: 01, and set data: 00.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: AA, change the data and set the voltage (A) between the pedestal (0 IRE) and 100 IRE to the specified value. (The data of address: AA should be “00” to “7F”.) Note: The contrast adjustment mode is set up automatically, so the 3 steps signal is displayed on the LCD screen.
3) 4)
Signal Measurement Point
Press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.
100IRE
A
2H Pedestal
Fig. 5-1-24.
5-41
7. White Balance Adjustment (PD-124 board) Correct the white balance. If deviated, the reproduction of the LCD screen may degenerate. Mode VTR stop
6. V-COM Adjustment (PD-124 board) Set the DC bias of the common electrode drive signal of LCD to the specified value. If deviated, the LCD display will move, producing flicker and conspicuous vertical lines. Mode VTR stop Signal Measurement Point
No signal Check on LCD display
Measuring Instrument Adjustment Page
D
Adjustment Address Specified Value
A4 The brightness difference between the section A and section B is minimum.
Measuring Instrument Adjustment Page
D
Adjustment Address Specified Value
A8, A9 The LCD screen should not be colored.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A8 and A9, set the data to the initial value.
Note: The V-COM adjustment mode is set up automatically, so the V COM adjustment signal is displayed on the LCD screen.
5)
No signal Check on LCD screen
Note: Check the white balance only when replacing the following parts. If necessary, adjust them. 1. LCD panel 2. Light induction plate 3. IC3101
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: A4, change the data so that the brightness of the section A and that of the section B is equal. (The data of address: A4 should be “00” to “3F”.) 3) 4)
Signal Measurement Point
Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data.
Press the PAUSE button of the adjustment remote commander. Select page: D, address: A4, substract 1 (TRV20E) or 3 (TRV6/ TRV6E) from the data, and press the PAUSE button. Select page: 0, address: 01, and set data: 00.
Address Data 3)
B
A
A
B
B
A
A9 72
Check that the LCD screen is not colored. If colored, change the data of page: D, address: A8 and A9 so that the LCD screen is not colored. Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data. When address: A8 or A9 is selected, the white balance adjustment mode is set up automatically.
4) A
A8 8A
B
Fig. 5-1-25.
5-42
Select page: 0, address: 01, and set data: 00.
5-2. MECHANISM SECTION ADJUSTMENT On the mechanism section adjustment For details of mechanism section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL J Mechanism ”.
2-1.
1) 2) 3) 4)
2-3.
Note: Only for the DCR-TRV20/TRV20E model, the lens block (CD-252 board) must be connected when performing the adjustments.
1. Preparation for Adjustment 1) Clean the tape running side (tape guide, drum, capstan shaft, pinch roller, etc.). 2) Connect the adjustment remote commander to the LANC jack. 3) Turn the HOLD switch of the adjustment remote commander to the ON position. 4) Connect an oscilloscope to VC-240/241 board CN009 via the CPC-8 jig (J-6082-388-A). Channel 1: VC-240/241 board, CN009 Pin w; (Note) External trigger: VC-240/241 board, CN009 Pin qj
HOW TO ENTER RECORD MODE WITHOUT CASSETTE
Connect the adjustment remote commander to the LANC jack. Turn the HOLD switch of the adjustment remote commander to the ON position. Close the cassette compartment without the cassette. Select page: 3, address: 01, set data: 0C, and press the PAUSE button of the adjustment remote commander. (The mechanism enters the record mode automatically.)
Note: Connect a 75 Ω resistor between pins w; of CN009 and ql (GND). 75 Ω resistor (Parts code: 1-247-804-11)
Note: The function buttons become inoperable.
5)
To quit the record mode, select page: 3, address: 01, set data: 00, and press the PAUSE button of the adjustment remote commander. (Whenever you want to quit the record mode, be sure to quit following this procedure.)
2-2.
1) 2) 3) 4)
5) 6) 7) 8)
HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE
Connect the adjustment remote commander to the LANC jack. Turn the HOLD switch of the adjustment remote commander to the ON position. Close the cassette compartment without the cassette. Select page: 3, address: 01, set data: 0B, and press the PAUSE button of the adjustment remote commander. (The mechanism enters the playback mode automatically.)
Playback the alignment tape for tracking. (XH2-1) Select page: 3, address: 33, and set data: 08. Select page: 3, address: 26, and set data: 31. Check that the oscilloscope RF waveform is normal at the entrance and exit. If not normal, adjust according to the separate volume “DV MECHANICAL ADJUSTMENT MANUAL J Mechanism ” .
CN009 of VC-240/241 board Pin No. Signal Name Pin No. 1 LACN SIG 2 3 EVF BL– 4 5 EVF VCO 6 7 PANEL VG 8 9 H START 10 11 PANEL COM 12 13 TCK 14 15 JIG TDO 16 17 SWP 18 19 GND 20
Note: The function buttons become inoperable.
5)
TAPE PATH ADJUSTMENT
To quit the playback mode, select page: 3, address: 01, set data: 00, and press the PAUSE button of the adjustment remote commander. (Whenever you want to quit the playback mode, be sure to quit following this procedure.)
Signal Name EVF BL+ EVF VG GND PD VCO XHD/PSIG TMS JIG TDI GND RF IN/LANC JACK IN RF MON
2. Procedure after operations 1) Connect the adjustment remote commander to the LANC jack and set the HOLD switch to the ON position. 2) Select page: 3, address: 26, and set data: 00. 3) Select page: 3, address: 33, and set data: 00. Entrance side
Check this section (Normal waveform)
CH1
CH2 (Trigger) 3.3msec
Fig. 5-2-1.
5-43
Exit side
5-3. VIDEO SECTION ADJUSTMENTS NTSC model : DCR-TRV6/TRV11/TRV20 PAL model : DCR-TRV6E/TRV11E/TRV20E
3-1.
PREPARATIONS BEFORE ADJUSTMENTS
Use the following measuring instruments for video section adjustments. 3-1-1. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11)
12) 13) 14) 15)
Equipment Required
TV monitor Oscilloscope (dual-phenomenon, band above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.) Frequency counter Pattern generator with video output terminal. Digital voltmeter Audio generator Audio level meter Audio distortion meter Audio attenuator Regulated power supply Alignment tapes • Tracking standard (XH2-1) Parts code: 8-967-997-01 • SW/OL standard (XH2-3) Parts code: 8-967-997-11 • Audio operation check for NTSC (XH5-3) Parts code: 8-967-997-51 • System operation check for NTSC (XH5-5) Parts code: 8-967-997-61 • BIST check for NTSC (XH5-6) Parts code: 8-967-997-71 • Audio operation check for PAL (XH5-3P) Parts code: 8-967-997-55 • System operation check for PAL (XH5-5P) Parts code: 8-967-997-66 • BIST check for PAL (XH5-6P) Parts code: 8-967-997-76 Adjustment remote commander (J-6082-053-B) CPC-8 jig (J-6082-388-A) IR receiver jig (J-6082-383-A) Extension cable (80P, 0.4 mm) For extension between the DD-137 board (CN1603) and the VC-240/241 board (CN002) (J-6082-395-A)
5-44
Note 1: Setting the “Forced VTR Power ON” mode (VTR mode) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 02, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the VTR power to be turned on with the control switch block (FK-30150 block) removed. After completing adjustments, be sure to exit the “Forced Power ON mode”. Note 2: Setting the “Forced Camera Power ON” mode (Camera mode) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the camera power to be turned on with the control switch block (FK-30150 block) removed. After completing adjustments, be sure to exit the “Forced Power ON mode”. Note 3: Setting the “Forced Memory Power ON” mode (Memory mode) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 05, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the memory power to be turned on with the control switch block (FK-30150 block) removed. After completing adjustments, be sure to exit the “Forced Power ON mode”. Note 4: Exiting the “Forced Power ON” mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00. Note 5: CK-92 board: DCR-TRV11/TRV11E/TRV20 CK-94 board: DCR-TRV6/TRV6E/TRV20E VC-240 board: DCR-TRV20/TRV20E VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E
3-1-2. Precautions on Adjusting 1) The adjustments of this unit are performed in the VTR mode or camera mode. To set to the VTR mode, set the power switch to “VCR” (or “PLAYER”) or set the “Forced VTR Power ON mode” using the adjustment remote commander (Note 1). To set to the Camera mode, set the power switch to “CAMERA” or set the “Forced Camera Power ON mode” using the adjustment remote commander (Note 2). After completing adjustments, be sure to exit the “Forced VTR Power ON Mode” or “Forced Camera Power ON Mode”. (Note 3) 2) The front panel block (MA-385 board, microphone unit, remote commander receiver, LANC/DIGITAL I/O jack, MIC jack) must be assembled because the audio/video jack is used for connecting the monitor TV. To remove, disconnect the following connector. MA-385 board CN2071 (28P, 0.5mm) 3) Cabinet (R) (CK-92/94board, LCD block) need not be connected. But removing the cabinet (R) (removing the VC240/241 board CN003) means removing the lithium 3V power supply (CK-92/94 board, BT3201) , data such as date, time, user-set menus will be lost. After completing adjustments, reset these data. If the cabinet (R) has been removed, the selfdiagnosis data, data on history of use (total drum rotation time etc.) will be lost. Before removing, note down the self-diagnosis data and the data on the history use (data of page: 2, address: A2 to AA). (Refer to “SELF-DIAGNOSIS FUNCTION” for the self-diagnosis data, and to “5-4.Service Mode” for the data on the history use.) To remove the cabinet (R), disconnect the following connectors. VC-240/241 board CN003 (51P, 0.3mm) 4) The viewfinder (LB-64 board) is need not be connected. To remove it, disconnect the following connector. DD-137 board CN1604 (27P, 0.3mm) 5) For extension between the DD-137 board CN1603 and VC240/241 board CN002, use the following extension cable. J-6082-395-A (80P, 0.4mm) 6) Only for the DCR-TRV20/TRV20E model, the lens block (CN701 of VC-240 board) must be connected when performing adjustments, because the timing generator (IC102) is provided on the CD-252 board of the lens block.
5-45
3-1-3. Adjusting Connectors Some of the adjusting points of the video section are concentrated at VC-240/241 board CN009. Connect the measuring instruments via the CPC-8 jig (J-6082-388-A). The following table lists the pin numbers and signal names of CN009. Pin No. 1 3 5 7 9 11 13 15 17 19
Signal Name LACN SIG EVF BL– EVF VCO PANEL VG H START PANEL COM TCK JIG TDO SWP GND
Pin No. 2 4 6 8 10 12 14 16 18 20
Signal Name EVF BL+ EVF VG GND PD VCO XHD/PSIG TMS JIG TDI GND RF IN/LANC JACK IN RF MON
CN009 1
2
19
20
Remove the CPC lid
Fig. 5-3-1
Table 5-3-1.
3-1-4. Connecting the Equipment Connect the measuring instruments as shown in Fig. 5-3-2, and perform the adjustments.
VTR recording mode (Except AEP/UK model) Pattern generator Video output (75 Ω)
VIDEO (Yellow)
Adjustment remote commander
AUDIO L (White)
Main unit
AUDIO R (Red)
LANC jack
AUDIO/VIDEO jack
Playback mode
TV monitor VIDEO (Yellow) Main unit AUDIO L (White)
Adjustment remote commander
AUDIO R (Red) LANC jack
AUDIO/VIDEO jack
Fig. 5-3-2. 3-1-5. Checking the Input Signals (Except AEP/UK model) Because the video signal obtained from the pattern generator is used as the adjustment signal for adjusting the VTR section, the video output signal must satisfy the given specifications. Connect the oscilloscope to the video terminal of the AUDIO/ VIDEO jack, and check that the sync signal amplitude of the video signal is approximately [0.30V], the amplitude of the video section is approximately [0.70V], the amplitude of the burst signal is approximately [0.30V] and flat, and that the level ratio of the burst signal to the “red” signal is 0.30 : 0.60. The video signal used for adjusting the video section is shown in Fig. 5-3-3. < > : NTSC model [ ] : PAL model
5-46
3-1-6. Alignment Tapes Use the alignment tapes shown in the following table. Use tapes specified in the signal column of each adjustment. Name Tracking standard (XH2-1) SW/OL standard (XH2-3) Audio operation check (XH5-3 (NTSC), XH5-3P (PAL)) System operation check (XH5-5 (NTSC), XH5-5P (PAL)) BIST check (XH5-6 (NTSC), XH5-6P (PAL))
Use Tape path adjustment Switching position adjustment Audio system adjustment Operation check BIST check
Fig. 5-3-3 shows the 75% color bar signals recorded on the alignment tape for Audio Operation Check. Note: Measure with video terminal (Terminated at 75 Ω)
For NTSC model
Blue
Red
Magenta
Green
(75%)
1V
Cyan
Burst signal
Yellow
0.714V
White
Cyan Green Magenta Red Blue
White (75%)
Yellow
White (100%)
0.286V 0.286V
Q
Q
I
Black
I White (100%)
Horizontal sync signal Color bar signal waveform
Color bar pattern
Black
Blue
Red
Magenta
Green
Cyan
0.3V
Yellow
White
0.7V 1V
Magenta Red Blue
White (100%)
Yellow Cyan Green
For PAL model
(100%)
0.3V Burst signal
Horizontal sync signal
Color bar signal waveform
Color bar pattern
Fig. 5-3-3. Color bar signal of alignment tapes 3-1-7. Input/Output Level and Impedance Video input/output Special stereo mini jack Video signal: 1 Vp-p, 75 Ω unbalanced, sync negative S video input/output 4-pin mini DIN Luminance signal: 1 Vp-p, 75 Ω unbalanced, sync negative Chrominance signal: 0.286 Vp-p, 75 Ω unbalanced (NTSC) : 0.300 Vp-p, 75 Ω unbalanced (PAL)
Audio input/output Special stereo mini jack Input level: 327mV Input impedance: More than 47kΩ Output level: 327 mV (at load impedance 47 kΩ) Output impedance: Below 2.2 kΩ
5-47
3-2.
2-2. Serial No. Input Write the serial No. and model code in the EEPROM (nonvolatile memory). Convert the serial No. on the name plate from decimal to hexadecimal, and write in the EEPROM. Page C
SYSTEM CONTROL SYSTEM ADJUSTMENT
1. Initialization of B, C, D, E, F, 7, 8 Page Data If the B, C, D, E, F, 7, 8 page data is erased due to some reason, perform “1-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”
Address
2. Serial No. Input 2-1. Company ID Input Write the company ID in the EEPROM (nonvolatile memory). Page C Address
Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Read the serial No. on the name plate, and take it as D1. Example: If the serial No. is 77881. D1=77881 3) Obtain D2 and H1 corresponding to D1 from Table 5-3-2. Example: If D1 is “77881”. D2=D1–65536=12345 H1=FE H1 (Hexadecimal) D1 (Decimal) D2 (Decimal) (Service model code) 000001 to 065535 D1 FE 065536 to 131071 D1–65536 FE 131072 to 196607 D1–131072 FE
E8, E9, EA, EB, EC
Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Input the following data to page: C, addresses: E8 to EC. Note: Press the PAUSE button of the adjustment remote commander each time to set the data.
Address E8 E9 EA EB EC 3)
ED, EE, EF
Data 08 00 46 01 02
Table 5-3-2. 4)
Input H1 to page: C, address: ED. (Model code input) Example: If H1 is “FE”. Select page: C, address: ED, set data: FE, and press the PAUSE button. 5) Obtain the maximum decimal not exceeding D2 from Table 53-3, and take this as D3. Example: If D2 is “12345”. D3=12288 6) Obtain the hexadecimal corresponding to D3 from Table 5-3-3, and take this as H3. Example: If D3 is “12288”. H3=3000 7) Obtain the difference D4 between D 2 and D 3. (Decimal calculation, 0 D4 255) D4= D2–D3 Example: If D2 is “12345” and D3 is “12288”. D4=12345–12288=57 8) Convert D4 to hexadecimal, and take this as H4. (Refer to “Hexadecimal-decimal conversion table” in “5-4. Service Mode”.) Example: If D4 is “57”. H4=39 9) Input the upper 2 digits of H3 to page: C, address: EE. Example: If H3 is “3000”. Select page: C, address: EE, set data: 30, and press the PAUSE button. 10) Input H4 to page: C, address: EF. Example: If H4 is “39”. Select page: C, address: EF, set data: 39, and press the PAUSE button. 11) Select page: 0, address: 01, and set data: 00.
Select page: 0, address: 01, and set data: 00.
5-48
HexaHexaHexaHexaHexaHexaHexaHexaDecimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal Decimal decimal (D3) (D3) (D3) (D3) (D3) (D3) (D3) (D3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3)
0 256 512 768 1024 1280 1536 1792 2048 2304 2560 2816 3072 3328 3584 3840 4096 4352 4608 4864 5120 5376 5632 5888 6144 6400 6656 6912 7168 7424 7680 7936
0000 0100 0200 0300 0400 0500 0600 0700 0800 0900 0A00 0B00 0C00 0D00 0E00 0F00 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 1A00 1B00 1C00 1D00 1E00 1F00
8192 8448 8704 8960 9216 9472 9728 9984 10240 10496 10752 11008 11264 11520 11776 12032 12288 12544 12800 13056 13312 13568 13824 14080 14336 14592 14848 15104 15360 15616 15872 16128
2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 2A00 2B00 2C00 2D00 2E00 2F00 3000 3100 3200 3300 3400 3500 3600 3700 3800 3900 3A00 3B00 3C00 3D00 3E00 3F00
16384 16640 16896 17152 17408 17664 17920 18176 18432 18688 18944 19200 19456 19712 19968 20224 20480 20736 20992 21248 21504 21760 22016 22272 22528 22784 23040 23296 23552 23808 24064 24320
4000 4100 4200 4300 4400 4500 4600 4700 4800 4900 4A00 4B00 4C00 4D00 4E00 4F00 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 5A00 5B00 5C00 5D00 5E00 5F00
24576 24832 25088 25344 25600 25856 26112 26368 26624 26880 27136 27392 27648 27904 28160 28416 28672 28928 29184 29440 29696 29952 30208 30464 30720 30976 31232 31488 31744 32000 32256 32512
6000 6100 6200 6300 6400 6500 6600 6700 6800 6900 6A00 6B00 6C00 6D00 6E00 6F00 7000 7100 7200 7300 7400 7500 7600 7700 7800 7900 7A00 7B00 7C00 7D00 7E00 7F00
32768 33024 33280 33536 33792 34048 34304 34560 34816 35072 35328 35584 35840 36096 36352 36608 36864 37120 37376 37632 37888 38144 38400 38656 38912 39168 39424 39680 39936 40192 40448 40704
Table 5-3-3.
5-49
8000 8100 8200 8300 8400 8500 8600 8700 8800 8900 8A00 8B00 8C00 8D00 8E00 8F00 9000 9100 9200 9300 9400 9500 9600 9700 9800 9900 9A00 9B00 9C00 9D00 9E00 9F00
40960 A000 49152 41216 A100 49408 41472 A200 49664 41728 A300 49920 41984 A400 50176 42240 A500 50432 42496 A600 50688 42752 A700 50944 43008 A800 51200 43264 A900 51456 43520 AA00 51712 43776 AB00 51968 44032 AC00 52224 44288 AD00 52480 44544 AE00 52736 44800 AF00 52992 45056 B000 53248 45312 B100 53504 45568 B200 53760 45824 B300 54016 46080 B400 54272 46336 B500 54528 46592 B600 54784 46848 B700 55040 47104 B800 55296 47360 B900 55552 47616 BA00 55808 47872 BB00 56064 48128 BC00 56320 48384 BD00 56576 48640 BE00 56832 48896 BF00 57088
C000 C100 C200 C300 C400 C500 C600 C700 C800 C900 CA00 CB00 CC00 CD00 CE00 CF00 D000 D100 D200 D300 D400 D500 D600 D700 D800 D900 DA00 DB00 DC00 DD00 DE00 DF00
57344 57600 57856 58112 58368 58624 58880 59136 59392 59648 59904 60160 60416 60672 60928 61184 61440 61696 61952 62208 62464 62720 62976 63232 63488 63744 64000 64256 64512 64768 65024 65280
E000 E100 E200 E300 E400 E500 E600 E700 E800 E900 EA00 EB00 EC00 ED00 EE00 EF00 F000 F100 F200 F300 F400 F500 F600 F700 F800 F900 FA00 FB00 FC00 FD00 FE00 FF00
3. Battery End Check (VC-240/241 board) Check the battery end voltage. Mode Camera recording and VTR playback Subject
Arbitrary
Note: It is normal though the following symptoms appear during the battery end check. 1) The message of “FOR InfoLITHIUM BATTERY ONLY” on the LCD or viewfinder screen. 2) The tally lamp is flashing.
Connection: 1) Connect the regulated power supply and the digital voltmeter to the battery terminal as shown in Fig. 5-3-4. Checking method: 1) Adjust the output voltage of the regulated power supply so that the digital voltmeter display is 6.0 ± 0.1Vdc. 2) Turn off the power supply. 3) Turn on the HOLD switch of the adjustment remote commander. 4) Turn on the power supply. 5) Load a cassette, and set to the camera recording mode. 6) Decrease the output voltage of the regulated power supply so that the digital voltmeter display is 5.5 ± 0.1Vdc. 7) Record the camera signal for a minute. 8) Playback the recorded section and check that the playback picture and sound are normal.
Regulated power supply +
5.5 ± 0.01 Vdc
+ +
Digital volt meter
Fig. 5-3-4.
5-50
Ver 1.1 2000. 06
3-3.
2. PLL f0 & LPF f0 Adjustment (VC-240/241 board)
SERVO AND RF SYSTEM ADJUSTMENT
Before perform the servo and RF system adjustments, check that the specified value of “36MHz/54MHz/66MHz Origin Oscillation Adjustment” of “CAMERA SYSTEM ADJUSTMENT” is satisfied. Note: Only for the DCR-TRV20/TRV20E model, the lens block (CD-252 board) must be connected when performing the adjustment.
Adjusting Procedure: 1. Cap FG duty adjustment 2. PLL f0 & LPF f0 adjustment 3. Switching position adjustment 4. AGC center level and APC & AEQ adjustment 5. PLL f0 & LPF f0 final adjustment
Adjustment remote commander C
Adjustment Address Specified Value
16 00
Display data of page: 3, address: 03 Adjustment remote commander
Adjustment Page Adjustment Address
C 1F, 20, 22, 29
Specified Value
Bit2, bit3 and bit6 are “0”
Note: If bit2, bit3 or bit 6 of the data is “1”, there are errors. (For the error contents, see the following table. For the bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit value discrimination”.)
5)
Select page: 0, address: 01, and set data: 00.
Bit value of page: 3, address: 03 data bit 6 = 1 bit 3 = 1 bit 2 = 1
Adjusting method: 1) Close the cassette compartment without inserting a cassette. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 3, address: 01, set data: 1B, and press the PAUSE button of the adjustment remote commander. 4) Select page: 3, address: 02, and check that the data changes starting from “1B” to “2B” to “00” in this order. 5) Select page: 3, address: 03, and check that the data is “00”. Note: If the data of page: 3, address: 03 is “01”, adjustment has errors or the mechanism deck is defective.
6)
VTR stop
Measurement Point Measuring Instrument
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 01, set data: 30, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 02, and check that the data changes to “00”. 4) Select page: 3, address: 03, and check that bit2, bit3 and bit 6 of the data are “0”.
1. Cap FG Duty Adjustment (VC-240/241 board) Set the Cap FG signal duty cycle to 50% to establish an appropriate capstan servo. If deviated, the uneven rotation of capstan and noise can occur. Measurement Point Display data of page: 3, address: 03 Measuring Instrument Adjustment Page
Mode
Select page: 0, address: 01, and set data: 00.
5-51
Error contents LPF f0 is defective PLL f0, final adjustment is defective PLL f0, final adjustment time-out
4. AGC Center Level and APC & AEQ Adjustment
3. Switching Position Adjustment (VC-240/241 board) Mode
VTR playback
Signal Measurement Point
SW/OL reference tape (XH2-3) Display data of page: 3, address: 03
Measuring Instrument Adjustment Page
Adjustment remote commander C
Adjustment Address Specified Value
10, 11, 12, 13 00
4-1. Preparations before adjustments Mode Camera recording Subject
Adjusting method: 1) Select page: 2, address: 30, and set data: 40. 2) Record the camera signal for three minutes.
4-2. AGC Center Level Adjustment (VC-240/241 board) Mode Playback
Adjusting method: 1) Insert the SW/OL reference tape and enter the VTR STOP mode. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 3, address: 21, and check that the data is “02”.
Signal Measurement Point
Note: If the data of page: 3, address: 21 is “72”, the tape top being played. After playing the tape for 1 to 2 seconds, stop it, perform step 4 and higher.
4) 5) 6)
Select page: 3, address: 01, set data: 0D, and press the PAUSE button of the adjustment remote commander. Select page: 3, address: 02, and check that the data changes to “00”. Select page: 3, address: 03, and check that the data is “00”. Note: If bit 0 of page: 3, address: 03 data is “1”, the even channel is defective. If bit 1 is “1”, the odd channel is defective. Contents of the defect is written into page: C, addresses: 10 and 12. See the following table. (For the bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit value discrimination”. )
7)
Arbitrary
Recorded signal at “Preparations before adjustments” Pin w; of CN009 (RF MON) (Note 1) Ext. trigger : Pin qj of CN009 (SWP)
Measuring Instrument Adjustment Page
Oscilloscope C
Adjustment Address Specified Value
1E The display data of page: 3, address: 03 is “00”
Note 1: Connect a 75Ω resistor between Pin w; and Pin ql (GND) of CN009. 75Ω resistor (Parts code: 1-247-804-11)
Select page: 0, address: 01, and set data: 00.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Playback the recorded signal at “Preparations before adjustments” 3) Select page: 3, address: 33, and set data: 08. 4) Confirm that the playback RF signal is stable. 5) Select page: 3, address: 01, set data: 23, and press the PAUSE button of the adjustment remote commander. 6) Select page: 3, address: 02, and check that the data is “00”. 7) Select page: 3, address: 03, and check that the data is “00”.
When the even channel is defective Data of page: C, Contents of defect address: 10 EE Writing into EEPROM (IC502) is defective E8 Adjustment data is out of range E7 No data is returned from IC301 (CAIN) When the odd channel is defective Data of page: C, Contents of defect address: 12 EE Writing into EEPROM (IC502) is defective E8 Adjustment data is out of range E7 No data is returned from IC301 (CAIN)
Note: If the data of page: 3, address: 03 is other than “00”, adjustment has errors. (Take an appropriate remedial measures according to the errors referring to the following table. )
8)
Perform “APC & AEQ Adjustment”.
Data of page: 3, address: 03 20 30 40 50
Contents of defect Perform re-adjustment. (Note 2) The machine is defective Perform re-adjustment (Note 2) The machine is defective
Note 2: If this data is displayed twice successively, the machine is defective.
PB RF signal is stable
Pin w;
Pin qj 6.7 msec
Fig. 5-3-5.
5-52
Ver 1.1 2000. 06
4-3. APC & AEQ Adjustment (VC-240/241 board)
5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board)
Mode
Playback
Mode
VTR stop
Signal
Recorded signal at “Preparations before adjustments” Pin w; of CN009 (RF MON) (Note 1) Ext. trigger : Pin qj of CN009 (SWP)
Signal Measurement Point
Arbitrary Display data of page: 3, address: 03
Measuring Instrument Adjustment Page
Adjustment remote commander C
Adjustment Address Specified Value
1F, 20, 22, 29 Bit2, bit3 and bit6 are “0”
Measurement Point Measuring Instrument Adjustment Page
Oscilloscope C
Adjustment Address Specified Value
18, 19, 1B, 1C, 21, 2C The display data of page: 3, address: 03 is “00”
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 01, set data: 30, and press the PAUSE button of the adjustment remote commander. 3) Select page: 3, address: 02, and check that the data changes to “00”. 4) Select page: 3, address: 03, and check that bit2, bit3 and bit 6 of the data are “0”.
Note 1: Connect a 75Ω resistor between Pin w; and Pin ql (GND) of CN009. 75Ω resistor (Parts code: 1-247-804-11) Note 2: The “AGC Center Level Adjustment” must have already been completed before starting this adjustment.
Note: If bit2, bit3 or bit 6 of the data is “1”, there are errors. (For the error contents, see the following table. For the bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit value discrimination”.)
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Playback the recorded signal at “Preparations before adjustments” 3) Select page: 3, address: 33, and set data: 08. 4) Check that the playback RF signal is stable. 5) Select page: 3, address: 01, set data: 07, and press the PAUSE button of the adjustment remote commander. 6) Select page: 3, address: 02, and check that the data changes from “07” to “00” in about 15 seconds after pressing the PAUSE button. 7) Select page: 3, address: 03, and check that the data is “00”.
5)
Note: If the data of page: 3, address: 03 is other than “00”, adjustment has errors. (Take an appropriate remedial measures according to the errors referring to the following table. )
8)
Perform “Processing after Completing Adjustments”.
Data of page: 3, address: 03 20 30 50 60 80
Select page: 0, address: 01, and set data: 00.
Bit value of page: 3, address: 03 bit 6 = 1 bit 3 = 1 bit 2 = 1
Contents of defect Perform re-adjustment. (Note 3) The machine is defective Perform re-adjustment (Note 3) The machine is defective The machine is defective
Note 3: If this data is displayed twice successively, the machine is defective.
4-4. Processing after Completing Adjustments 1) Select page: 2, address: 30, and set data: 00. 2) Select page: 3, address: 33, and set data: 00. 3) Select page: 0, address: 01, and set data: 00. PB RF signal is stable
Pin w;
Pin qj 6.7 msec
Fig. 5-3-6.
5-53
Error contents LPF f0 is defective PLL f0 final adjustment is defective PLL f0 final adjustment time-out
3-4.
2. S VIDEO OUT Y Level Adjustment (VC-240/241 Board)
VIDEO SYSTEM ADJUSTMENTS
Before perform the video system adjustments, check that the specified value of “36MHz/54MHz/66MHz Origin Oscillation Adjustment” of “CAMERA SYSTEM ADJUSTMENT” is satisfied. Note: Only for the DCR-TRV20/TRV20E model, the lens block (CD-252 board) must be connected when performing the adjustments.
3-4-1.
Base Band Block Adjustments
1. Chroma BPF f0 Adjustment (VC-240/241 Board) Set the center frequency of IC1301 chroma band-pass filter. Mode Camera Subject Measurement Point
All black (Cover the lens with the lens cap) CH1: Chroma signal terminal of S VIDEO jack (75Ω terminated) CH2: Y signal terminal of S VIDEO jack (75Ω terminated)
Measuring Instrument Adjustment Page
Oscilloscope C
Adjustment Address Specified Value
28 A = 100mVp-p or less B = 200mVp-p or more
Camera
Subject Measurement Point
Arbitrary Y signal terminal of S VIDEO jack (75Ω terminated)
Measuring Instrument Adjustment Page
Oscilloscope C
Adjustment Address Specified Value
25 A = 1000 ± 14mV
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 35. After noting down the data of this address, set data: 01 to the address. 3) Select page: 3, address: 0C, set data: 02, and press the PAUSE button of the adjustment remote commander. 4) Select page: C, address: 25, change the data and set the Y signal level (A) to the specified value. 5) Press the PAUSE button. 6) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 7) Select page: 2, address: 35, and set the data that is noted down at step 2). 8) Select page: 0, address: 01, and set data: 00.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Check that the burst signal (B) is output to the chroma signal terminal of S VIDEO jack. 3) Select page: 3, address: 0C, set data: 04, and press the PAUSE button. 4) Select page: C, address: 28, and change the data for minimum amplitude of the burst signal level (A). (The data of address: 28 should be “00” to “07”.) 5) Press the PAUSE button. 6) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 7) Check that the burst signal level (B) satisfies the specified value. 8) Select page: 0, address: 01, and set data: 00.
Center of luminance line
A
H
Fig. 5-3-8.
When the data of page: 3, address: 0C, is 04: A CH1
CH2
H
When the data of page: 3, address: 0C, is 00:
CH1
Mode
B
H
Fig. 5-3-7.
5-54
3. S VIDEO OUT Chroma Level Adjustment (VC-240/241 Board) Mode Camera Subject Measurement Point
4. AV OUT Y, Chroma Level Check (VC-240/241 Board)
Arbitrary Chroma signal terminal of S VIDEO jack (75Ω terminated) External trigger: Y signal terminal of S VIDEO jack
Measuring Instrument Adjustment Page
Oscilloscope C
Adjustment Address Specified Value
26, 27 Cr level:
A = 714 ± 14mV(NTSC) A = 700 ± 14mV(PAL) Cb level: B = 714 ± 14mV(NTSC) B = 700 ± 14mV(PAL) Burst level: C = 286 ± 6mV(NTSC) C = 300 ± 6mV(PAL)
Arbitrary Video terminal of AUDIO/VIDEO jack (75Ω terminated)
Measuring Instrument Specified Value
Oscilloscope Sync level: A = 286 ± 18mV(NTSC) A = 300 ± 18mV(PAL) Burst level: B = 286 ± 18(mV(NTSC) B = 300 ± 18mV(PAL)
B A H
Fig. 5-3-10.
H
C
0.28 µsec (NTSC) 0.23 µsec (PAL)
Camera
Subject Measurement Point
Adjusting method: 1) Select page: 2, address: 35. After noting down the data of this address, set data: 01 to the address. 2) Select page: 3, address: 0C, set data: 02, and press the PAUSE button of the adjustment remote commander. 3) Check that the sync signal level (A) satisfies the specified value. 4) Check that the burst signal level (B) satisfies the specified value. 5) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 6) Select page: 2, address: 35, and set the data that is noted down at step 1).
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 35. After noting down the data of this address, set data: 01 to the address. 3) Select page: 3, address: 0C, set data: 02, and press the PAUSE button of the adjustment remote commander. 4) Select page: C, address: 26, change the data and set the Cr signal level (A) to the specified value. 5) Press the PAUSE button. 6) Select page: C, address: 27, change the data and set the Cb signal level (B) to the specified value. 7) Press the PAUSE button. 8) Check that the burst signal level (C) is satisfied the specified value. 9) Select page: 3, address: 0C, set data: 00, and press the PAUSE button. 10) Select page: 2, address: 35, and set the data that is noted down at step 2). 11) Select page: 0, address: 01, and set data: 00.
A
Mode
B
0.28 µsec (NTSC) 0.23 µsec (PAL)
Fig. 5-3-9.
5-55
3-4-2.
BIST Check
1-4. IC301 VFD PB BIST Check • EX Y BIST Check 1) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 2) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 3) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 4) When the IC301 EX Y playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 FB 15 F4
1. Playback System Check 1-1. Preparations for Playback 1) Set the POWER switch to VCR (or PLAYER) position. 2) Connect the adjustment remote commander and set the HOLD switch to ON (SERVICE) position. 3) Select page: 0, address: 01, and set data: 01. 4) Select page: C, address: 42, set data: 00, and press the PAUSE button. 5) Playback the BIST check tape. (XH5-6 (NTSC), XH5-6P (PAL)) Note1:Perform the following checks in the playback mode. Note2: Use the AC power adaptor (AC-L10 etc.) or the info LITHIUM battery (NP-FM50 etc.).
1-2. IC301 TRX (RF) PB BIST Check 1) Select page: 3, address: 70, set data: 04, and press the PAUSE button. 2) Select page: 3, address: 70, set data: 00, and press the PAUSE button. 3) When the IC301 TRX (RF) playback system is normal, the display data (combination data) of page: 3, address: 73 and 74 agrees with any combination as shown below. NTSC model Address Data 73 63 C5 75 D3 59 FF 74 84 55 07 D6 01 D0 PAL model Address 73 86 74 35
Data AA 33
PAL model Address Data 14 54 15 ED • EVF Y BIST Check 5) Select page: 3, address: 10, set data: 88, and press the PAUSE button. 6) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 7) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 8) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 9) When the IC301 EVF Y playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 9B 15 C3
90 B6
1-3. IC301 AUD (ABUS) PB BIST Check 1) Select page: 3, address: 11, set data: 04, and press the PAUSE button. 2) Select page: 3, address: 12, set data: 08, and press the PAUSE button. 3) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 4) Select page: 3, address: 13, set data: 03, and press the PAUSE button. 5) When the IC301 AUD (ABUS) playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 41 15 81
PAL model Address Data 14 20 15 F8 • EVF Cr BIST Check 10) Select page: 3, address: 10, set data: 89, and press the PAUSE button. 11) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 12) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 13) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 14) When the IC301 EVF Cr playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 2E 15 34
PAL model Address Data 14 2D 15 7C
PAL model Address Data 14 33 15 DD
5-56
• EVF Cb BIST Check 15) Select page: 3, address: 10, set data: 8A, and press the PAUSE button. 16) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 17) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 18) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 19) When the IC301 EVF Cb playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 A9 15 39
• PANEL Cb BIST Check 30) Select page: 3, address: 10, set data: 9A, and press the PAUSE button. 31) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 32) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 33) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 34) When the IC301 PANEL Cb playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 A9 15 39
PAL model Address Data 14 AA 15 03
PAL model Address Data 14 AA 15 03
• PANEL Y BIST Check 20) Select page: 3, address: 10, set data: 98, and press the PAUSE button. 21) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 22) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 23) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 24) When the IC301 PANEL Y playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 9B 15 C3
1-5. IC301 ENCODER BIST Check 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 8, address: 21, set data: 0F, and press the PAUSE button. • ENCODER Ya BIST Check 3) Select page: 3, address: 10, set data: 8B, and press the PAUSE button. 4) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 5) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 6) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 7) When the IC301 ENCODER Ya playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 FD 15 3E
PAL model Address Data 14 20 15 F8
PAL model Address Data 14 58 15 BE
• PANEL Cr BIST Check 25) Select page: 3, address: 10, set data: 99, and press the PAUSE button. 26) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 27) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 28) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 29) When the IC301 PANEL Cr playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 2E 15 34 PAL model Address Data 14 33 15 DD
5-57
• ENCODER Yb BIST Check 8) Select page: 3, address: 10, set data: 8C, and press the PAUSE button. 9) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 10) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 11) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 12) When the IC301 ENCODER Yb playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 94 15 D6
1-6. Processing after Completing Playback System Check 1) 2)
3) 4) 5)
PAL model Address Data 14 A1 15 ED • ENCODER Ca BIST Check 13) Select page: 3, address: 10, set data: 8D, and press the PAUSE button. 14) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 15) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 16) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 17) When the IC301 ENCODER Ca playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 11 4E FD 3B 15 PAL model Data Address 14 E8 7B 62 B0 15 • ENCODER Cb BIST Check 18) Select page: 3, address: 10, set data: 8E, and press the PAUSE button. 19) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 20) Select page: 3, address: 12, set data: 00, and press the PAUSE button. 21) Select page: 3, address: 13, set data: 04, and press the PAUSE button. 22) When the IC301 ENCODER Cb playback system is normal, the display data (combination data) of page: 3, address: 14 and 15 agrees with any combination as shown below. NTSC model Address Data 14 5C BC 20 A8 15 PAL model Data Address 14 96 35 79 7C 15
5-58
Select page: 0, address: 01, and set data: 01. Select page: C, address: 42, set the following data and press the PAUSE button. 00: DCR-TRV6/TRV6E 28: DCR-TRV11/TRV11E 48: DCR-TRV20/TRV20E Select page: 8, address: 21, set data: 03, and press the PAUSE button. Select page: 0, address: 01, and set data: 00. Turn off the power and turn on again.
2. Recording System Check 2-1. Preparations for recording 1) Playback the BIST check tape.(XH5-6(NTSC), XH5-6P(PAL)) 2) Select page: 3, address: 10, set data: C0, and press the PAUSE button. 3) Select page: 3, address: 11, set data: 07, and press the PAUSE button. 4) Enter the stop mode. 5) While keep the HOLD switch of the adjustment remote commander at ON(SERVICE) position, eject the BIST check tape and close the cassette compartment without inserting a cassette. 6) Set the power switch to “CAMERA”. 7) Select page: 3, address: 01, set data: 0C, and press the PAUSE button. 2-2. IC301 TRX (RF) BIST Check 1) Select page: 3, address: 70, set data: 04, and press the PAUSE button. 2) Select page: 3, address: 70, set data: 00, and press the PAUSE button. 3) When the IC301 TRX (RF) recording system from is normal, the display data (combination data) of page: 3, address: 71 and 72 agrees with any combination as shown below. NTSC model Address Data 26 5E 71 72 95 E3 PAL model Data Address 71 53 77 DF D5 72 2-3. Processing after Completing Recording System Check 1) 2)
Select page: 3, address: 01, set data: 00, and press the PAUSE button. Turn off the power and turn on again.
5-59
3-5.
2. IR Video Deviation Adjustment (VC-240/241 board) Mode VTR stop
IR TRANSMITTER ADJUSTMENTS
Adjust using a IR receiver jig (J-6082-383-A). Switch setting: SUPER LASER LINK ........................... ON (Red LED is lit) 1. IR Video Carrier Frequency Adjustment (VC-240/241 board) Mode VTR stop Signal Measurement Point
Arbitrary Pin 5 of CN003 of IR receiver jig (RF) (Or Pin qh of IC1901 of VC-240/241 board)
Measuring Instrument Adjustment Page
Frequency counter F
Adjustment Address Specified Value
Measuring Instrument Adjustment Page
Oscilloscope F
Adjustment Address Specified Value
6D A = 1.00 ± 0.05 V
Oscilloscope Main unit
6E f = 11.85 ± 0.05 MHz
IR receiver jig CN003 pin 5
Arbitrary VIDEO OUT terminal of IR receiver jig (Terminated at 75 Ω)
Connection of Equipment: Connect the measuring device as shown in the following figure, and adjust.
IR receiver jig
75 Ω
VIDEO OUT 75 Ω (1-247-804-11)
Connection of Equipment Connect the measuring device as shown in the following figure, and adjust. Main unit
Signal Measurement Point
Fig. 5-3-12.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 0C, set data: 02, and press the PAUSE button of the adjustment remote commander. 3) Select page: F, address: 6D, and change the data, set the video signal amplitude (A) to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 3, address: 0C, set data: 00, and press the PAUSE button of the adjustment remote commander. 6) Select page: 0, address: 01, and set data: 00.
Frequency counter
Fig. 5-3-11.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 0C, set data: 08, and press the PAUSE button of the adjustment remote commander. 3) Select page: F, address: 6E, change the data, and set the video carrier frequency (f) to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 3, address: 0C, set data: 00, and press the PAUSE button of the adjustment remote commander. 6) Select page: 0, address: 01, and set data: 00.
A
H
Fig. 5-3-13.
5-60
3. IR Audio Deviation Adjustment (VC-240/241 board) Mode VTR stop Signal
Measurement Point
Video : No signal Audio : 400Hz, –7.5dBs, Audio left and right terminal of AUDIO/VIDEO jack AUDIO L terminal and AUDIO R terminal of IR receiver jig (Terminated at 47kΩ)
Measuring Instrument Adjustment Page
Audio level meter F
Adjustment Address Specified Value
6C Signal level: –7.5 ± 1.0 dBs Level difference of L and R: Below 2dB
Connection of Equipment: Connect the measuring device as shown in the following figure, and adjust. Main unit IR receiver jig
Video (Yellow)
AUDIO/ VIDEO AUDIO OUT L R
Audio oscillator Audio Left (White)
Attenuator
Audio level meter 600 Ω
Audio Right (Red)
600 Ω: 270 Ω (1-249-410-11) + 330 Ω (1-249-411-11) 47k Ω 47k Ω (1-249-437-11)
Fig. 5-3-14. Preparation: (Only for the AEP/UK model of DCR-TRV6E/TRV11E) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 2C, after noting down the data of this address, set data: 32, and press the PAUSE button. 3) Turn off the HOLD switch of the adjustment remote commander. 4) Turn off the power. 5) Turn on the HOLD switch. 6) Turn on the power.
Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Connect the audio level meter to the AUDIO L terminal of the IR receiver jig. 3) Select page: F, address: 6C, change the data and set the 400Hz audio signal level to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Connect the audio level meter to the AUDIO R terminal of the IR receiver jig. 6) Check that the 400Hz audio signal level is within the specified value. If outside, repeat from step 2). 7) Only for AEP/UK model of DCR-TRV6E/TRV11E, select page: D. address: 2C, set the data noted down at step 2) of “Preparation”, and press the PAUSE button. 8) Select page: 0, address: 01, and set data: 00.
5-61
3-6.
AUDIO SYSTEM ADJUSTMENTS
[Connection of Audio System Measuring Devices] Connect the audio system measuring devices as shown in Fig. 5-3-15. Main unit
Recording (Camera mode)
Audio oscillator
600 Ω
MIC
Left
Right
Attenuator
600 Ω: 270 Ω (1-249-410-11) + 330 Ω (1-249-411-11)
Playback Main unit
TV monitor Video (Yellow) Left (White)
AUDIO/ VIDEO OUT
47k Ω
Audio level meter or Distortion meter
Right (Red)
47k Ω 47k Ω (1-249-437-11)
Fig. 5-3-15.
5-62
1. Playback Level Check Mode VTR playback Signal
Measurement Point Measuring Instrument Specified Value
4. Overall Noise Level Check Mode Camera recording and playback
Alignment tape: For audio operation check (XH5-3 (NTSC)) (XH5-3P (PAL)) Audio left or right terminal of AUDIO VIDEO jack
Signal Measurement Point Measuring Instrument Specified Value
Audio level meter and frequency counter 32 kHz mode: 1 kHz, +3.0 ± 2.0dBs 48 kHz mode: 1 kHz, +3.0 ± 2.0dBs 44.1 kHz mode: The 7.35kHz signal level during EMP OFF is +2.0 ± 2.0dBs. The 7.35kHz signal level during EMP ON is –6 ± 2 dB from the signal level during EMP OFF.
5. Overall Separation Check Mode Signal
Camera recording and playback 400Hz, –66dBs signal: MIC jack [left] (Connect the MIC jack [right] to GND)
Measurement Point Measuring Instrument
Audio [right] terminal of AUDIO VIDEO jack Audio level meter
Specified Value
Below –40dBs (IHF-A filter ON)
2. Overall Level Characteristics Check Camera recording and playback 400Hz, –66 dBs signal: MIC jack left and right
Measurement Point Measuring Instrument
Audio left or right terminal of AUDIO VIDEO jack Audio level meter
Specified Value
–7.5 ± 3.0dBs
< > : Left channel check [ ] : Right channel check Checking Method: 1) Input the 400Hz, –66dBs signal in the [left] terminal of the MIC jack only. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the signal level of the audio [right] terminal is the specified value.
Checking Method: 1) Input the 400Hz, –66dBs signal in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the 400Hz signal level is the specified value. 3. Overall Distortion Check Mode Signal
Camera recording and playback 400Hz, –66dBs signal: MIC jack left and right
Measurement Point
Audio left or right terminal of AUDIO VIDEO jack Audio distortion meter
Measuring Instrument Specified Value
Audio level meter Below –45dBs (IHF-A filter ON, 20kHz LPF ON)
Checking Method: 1) Insert a shorting plug in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the noise level is the specified value.
Checking Method: 1) Check that the playback signal level is the specified value.
Mode Signal
No signal: Insert a shorting plug in the MIC jack Audio left or right terminal of AUDIO VIDEO jack
Below 0.4% (200Hz to 6kHz BPF ON)
Checking Method: 1) Input the 400Hz, –66dBs signal in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the distortion is the specified value.
5-63
5-4. SERVICE MODE 4-1.
ADJUSTMENT REMOTE COMMANDER
2. Precautions upon using the adjustment remote commander Mishandling of the adjustment remote commander may erase the correct adjustment data at times. To prevent this, it is recommended that all adjustment data be noted down before beginning adjustments and new adjustment data after each adjustment.
The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjustment remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the non-volatile memory. 1. Using the adjustment remote commander 1) Connect the adjustment remote commander to the LANC terminal. 2) Set the HOLD switch of the adjustment remote commander to “HOLD” (SERVICE position). If it has been properly connected, the LCD on the adjustment remote commander will display as shown in Fig. 5-4-1.
Page
Data
Address
Fig. 5-4-1 3)
Operate the adjustment remote commander as follows. • Changing the page The page increases when the EDIT SEARCH+ button is pressed, and decreases when the EDIT SEARCH– button is pressed. There are altogether 16 pages, from 0 to F.
Hexadecimal 0 1 2 3 4 5 6 7 8 9 A B CD E F notation LCD Display 0 1 2 3 4 5 6 7 8 9 A b c d E F Decimal notation conversion value 0 1 2 3 4 5 6 7 8 9 10 1112 1314 15
4)
• Changing the address The address increases when the FF (M) button is pressed, and decreases when the REW (m) button is pressed. There are altogether 256 addresses, from 00 to FF. • Changing the data (Data setting) The data increases when the PLAY (N) button is pressed, and decreases when the STOP (x) button is pressed. There are altogether 256 data, from 00 to FF. • Writing the adjustment data The PAUSE button must be pressed to write the adjustment data (B, C, D, F, 7, 8 page) in the nonvolatile memory. (The new adjusting data will not be recorded in the nonvolatile memory if this step is not performed.) After completing all adjustments, turn off the main power supply once.
5-64
4-2.
DATA PROCESS
The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Indicates the hexadecimal-decimal conversion table. Hexadecimal-decimal Conversion Table Lower digit of hexadecimal
0
1
2
3
2 4
5
6
7
8
9
Upper digit of hexadecimal
1
A (A)
B (b)
C (c)
D (d)
E (E)
F (F)
0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
2
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
3
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
4
64
65
66
67
68
69
70
71
72
73
74
77
76
77
78
79
5
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
6
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
7
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
8
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
9
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
A ( A)
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
B (b)
176
179
180
181
182
183
184
185
186
187
188
189
190
191
C ( c)
177 193
178
192
194
195
196
197
198
199
200
201
202
203
204
205
206
207
D (d)
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
E (E)
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
F (F)
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
Note: The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander. (Example) If the DDS display or the adjustment remote commander shows BD (bd); Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point “189” of 1 and 2 in the above table is the corresponding decimal number.
Table. 5-4-1.
5-65
4-3.
SERVICE MODE 2-1. EMG Code (Emergency Code) Codes corresponding to the errors which occur are written in addresses F4, F8 and FC. The type of error indicated by the code are shown in the following table.
1. Setting the Test Mode Page D Address 10 Data Function 00 Normal 01 Forced camera power ON 02 Forced VTR power ON 03 Forced camera + VTR power ON 05 Forced memory power ON • Before setting the data , select page: 0, address: 01, and set data: 01. • For page D, the data set is recorded in the non-volatile memory by pressing the PAUSE button of the adjustment remote commander. In this case, take note that the test mode will not be exited even when the main power is turned off. • After completing adjustments/repairs, be sure to return the data of this address to 00, and press the PAUSE button of the adjustment remote commander. Select page: 0, address: 01, and set data: 00.
Code 00 10 11 22 23 24 30 40 42
2. Emergence Memory Address Page C Address F4 to FF Address Contents F4 EMG code when first error occurs Upper: MSW code when shift starts when first F6 error occurs Lower: MSW code when first error occurs Lower: MSW code to be moved when first error F7 occurs F8 EMG code when second error occurs Upper: MSW code when shift starts when second FA error occurs Lower: MSW code when second error occurs Lower: MSW code to be moved when second error FB occurs FC EMG code when last error occurs Upper: MSW code when shift starts when last error FE occurs Lower: MSW code when last error occurs Lower: MSW code to be moved when last error FF occurs When no error occurs in this unit, data “00” is written in the above addresses (F4 to FF). when first error occurs in the unit, the data corresponding to the error is written in the first emergency address (F4 to F7). In the same way, when the second error occurs, the data corresponding to the error is written in the second emergency address (F8 to FB). Finally, when the last error occurs, the data corresponding to the error is written in the last emergency address (FC to FF). Note: After completing adjustments, be sure to initialize the data of addresses F4 to FF to “00”.
Initializing method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 3, address: 01, set data: 37, and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00.
5-66
Emergency Type No error Loading motor emergency during loading Loading motor emergency during unloading T reel emergency during normal rotation S reel emergency during normal rotation T reel emergency (Short circuit between S reel terminal and T reel terminal) FG emergency at the start up of the capstan FG emergency at the start up of the drum FG emergency during normal rotation of the drum
Ver 1.1 2000. 06
2-2. MSW Code MSW when errors occur: Information on MSW (mode SW) when errors occur MSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved) MSW of target of movement: Information on target MSW of movement when the mechanism position is moved
Mechanical Position ← UNLOAD BL
EJ
LOAD → ULE
BL
SR
BL
GL
BL
STOP
BL
R/P
1 1 0 = 6
1 1 1 = 7 0 1 0 = 2
1 1 1 = 7 0 1 1 = 3
1 1 1 = 7 0 0 1 = 1
1 1 1 = 7 1 0 1 = 5
1 1 1 = 7
1 0 0 = 4
← C (MSB) ←B ← A (LSB)
LS chassis movement section
Lock released Cassette compartment
Pinch roller pressing
Position
Code
EJ
4
BL
7
ULE
5
SR GL
1 3
STOP
2
R/P
6
NULL
0
Contents Position at which the cassette component lock is released, at the farthest unload side mechanically at which the mechanism can move no further in the UNLOAD direction. BLANK code, at the boundary between codes. EJECT completion position. when the cassette is ejected, the mechanism will stop at this position. Cassette IN standby. The guide will start protruding out as the mechanism moves towards the LOAD position. Position at which it is possible to release the S ratchet. Guide loading are performed here. Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the brake is imposed on both reels. PB, REC, CUE, REVIEW, PAUSE positions. When pinch roller is pressed, and the tension regulator is ON, the mechanism is operating at this position in modes in which normal images are shown. Code not existing in the MD. Default value.
5-67
3. Bit value discrimination Bit values must be discriminated using the display data of the adjustment remote commander for following items. Use the table below to discriminate if the bit value is “1” or “0”. Display on the adjustment remote commander
Address Page
bit3 to bit0 discrimination bit7 to bit4 discrimination
Display on the adjustment remote commander 0 1 2 3 4 5 6 7 8 9 A (A) B (b) C (c) D (d) E (E) B F (F)
bit3 or bit7 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Bit values bit2 bit1 or or bit6 bit5 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1
bit0 or bit4 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Example: If “8E” is displayed on the adjustment remote commander, the bit values for bit7 to bit4 are shown in the A column, and the bit values for bit3 to bit0 are shown in the B column.
4. Switch check (1) Page 2 Bit 0 1 2 3 4 5 6 7
Address 43 Function VTR MODE SW (PS-30150 block S1) CAM STBY SW (PS-30150 block S1) START/STOP SW (PS-30150 block S2) EJECT SW (FK-30150 block S61) CC DOWN SW (Mechanism chassis) PHOTO FREEZE SW (FK-30150 block S71) PHOTO STBY SW (PS-30150 block S1)
When bit value=1 OFF OFF OFF OFF OFF (UP) OFF OFF
When bit value=0 ON ON ON ON ON (DOWN) ON ON
Using method: 1) Select page: 2, address: 43. 2) By discriminating the bit value of display data, the state of the switch can be discriminated.
5-68
5. Switch check (2) Page 2
Address 60 to 67
Using method: 1) Select page:2, address: 60 to 67. 2) By discriminating the display data, the pressed key can be discriminated. Address 60 (KEY AD0) (IC1104 od) 61 (KEY AD1) (IC1104 of) 62 (KEY AD2) (IC1104 og) 63 (KEY AD3) (IC1104 oh) 64 (KEY AD4) (IC1104 oj) 65 (KEY AD5) (IC1104 ok) 66 (KEY AD6) (IC1104 ol) 67 (KEY AD7) (IC1104 FB101 FB102 FB103 FB104 FB105
1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11
FERRITE FERRITE FERRITE FERRITE FERRITE
0UH 0UH 0UH 0UH 0UH
FB106 FB108 FB109
1-414-445-11 FERRITE 1-414-445-11 FERRITE 1-414-656-11 FERRITE
0UH 0UH 0UH
< CAPACITOR > C101 C102 C103 C104 C105
1-164-004-11 1-125-777-11 1-107-687-11 1-104-851-11 1-125-777-11
CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP
0.1uF 0.1uF 3.3uF 10uF 0.1uF
10% 10% 20% 20% 10%
25V 10V 20V 10V 10V
C106 C107 C108 C109 C110
1-113-987-11 1-104-851-11 1-107-826-91 1-125-777-11 1-164-937-11
TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
4.7uF 10uF 0.1uF 0.1uF 0.001uF
20% 20% 10% 10% 10%
25V 10V 16V 10V 16V
C111 C112 C113 C114 C116
1-164-845-11 1-164-937-11 1-107-819-11 1-107-820-11 1-107-687-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP
5PF 0.001uF 0.022uF 0.1uF 3.3uF
0.25PF 16V 10% 16V 10% 16V 16V 20% 20V
C118 C119 C120 C122 C124
1-125-777-11 1-125-777-11 1-125-777-11 1-125-777-11 1-117-919-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP
0.1uF 0.1uF 0.1uF 0.1uF 10uF
10% 10% 10% 10% 20%
10V 10V 10V 10V 6.3V
C125 C126 C127 C128 C129
1-125-777-11 1-117-919-11 1-125-777-11 1-125-777-11 1-117-919-11
CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP
0.1uF 10uF 0.1uF 0.1uF 10uF
10% 20% 10% 10% 20%
10V 6.3V 10V 10V 6.3V
C130 C131 C132 C151 C152
1-125-777-11 1-164-870-11 1-162-966-11 1-117-919-11 1-125-837-91
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP
0.1uF 68PF 0.0022uF 10uF 1uF
10% 5% 10% 20% 10%
10V 16V 50V 6.3V 6.3V
< IC > IC101 IC102 IC103 IC104
CCD BLOCK ASSY IC CXD2477R-T4 IC TA75S01F(TE85R) IC AD80017JRURL < COIL >
L101 L103 L104 L105 L151
1-469-528-91 1-414-771-91 1-414-771-91 1-414-771-91 1-414-771-91
INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP
100uH 10uH 10uH 10uH 10uH
< TRANSISTOR > Q101 Q102 Q103 Q104
8-729-037-74 8-729-050-22 8-729-041-23 8-729-037-74
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
UN9213J-(TX).SO 2SC4250(T5LSONY1) NDS356AP UN9213J-(K8).SO
< RESISTOR >
< CONNECTOR > CN101 CN151 CN152
A-7031-073-A 8-752-400-37 8-759-075-66 8-759-638-68
1-784-939-11 CONNECTOR, BOARD TO BOARD 60P 1-784-421-11 CONNECTOR, FFC/FPC (ZIF) 27P 1-766-335-21 CONNECTOR, FFC/FPC 5P
R102 R104 R105 R106 R107
1-216-808-11 1-218-990-11 1-218-961-11 1-218-962-11 1-218-985-11
METAL CHIP SHORT RES-CHIP RES-CHIP RES-CHIP
82 0 4.7K 5.6K 470K
5%
1/16W
5% 5% 5%
1/16W 1/16W 1/16W
R108 R109 R112 R113 R114
1-218-967-11 1-218-990-11 1-218-981-11 1-218-965-11 1-218-989-11
RES-CHIP SHORT RES-CHIP RES-CHIP RES-CHIP
15K 0 220K 10K 1M
5%
1/16W
5% 5% 5%
1/16W 1/16W 1/16W
R122 R123
1-218-990-11 SHORT 1-218-990-11 SHORT
0 0
< DIODE > D101
Be sure to read “Precautions upon replacing CCD imager” on page 4-12 when changing the CCD imager.
8-713-103-84 DIODE 1T379-01-T8A
6-11
CD-252 Ref. No.
CK-92
Part No.
CK-94
Description
Remarks
Ref. No.
< VIBRATOR > X101 1-781-632-21 VIBRATOR, CRYSTAL (66MHz)(TRV20) X101 1-781-633-21 VIBRATOR, CRYSTAL (54MHz)(TRV20E) ************************************************************ A-7074-313-A CK-92(H) BOARD, COMPLETE (TRV11/TRV11E/TRV20) ************************************ (Ref.No.;30000Series)
Part No.
Description
S3206 S3207 S3208 S3209 S3210
1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61
SWITCH, KEY BOARD (MEMORY +) SWITCH, KEY BOARD (DIGITAL EFFECT) SWITCH, KEY BOARD (SELF TIMER) SWITCH, KEY BOARD (MEMORY -) SWITCH, KEY BOARD (TITLE)
Remarks
S3211 S3212 S3213 S3214 S3215
1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61
SWITCH, KEY BOARD (END SEARCH) SWITCH, KEY BOARD (MEMORY MIX) SWITCH, KEY BOARD (PB ZOOM) SWITCH, KEY BOARD (DATA CODE) SWITCH, KEY BOARD (MEMORY DELETE)
< BATTERY > S3216 1-771-138-61 SWITCH, KEY BOARD (MENU) S3217 1-771-138-61 SWITCH, KEY BOARD (DISPLAY) S3218 1-771-138-61 SWITCH, KEY BOARD (RESET) ************************************************************
BT3201 1-528-724-21 BATTERY, V/L RECHARGEABLE < CAPACITOR > C3201 C3203
1-104-913-11 TANTAL. CHIP 1-104-919-11 TANTAL. CHIP
10uF 10uF
20% 20%
A-7074-396-A CK-94(H) BOARD, COMPLETE (TRV20E) ******************************** A-7074-393-A CK-94(L) BOARD, COMPLETE (TRV6/TRV6E) ************************************ (Ref.No.;30000Series)
16V 25V
< CONNECTOR > CN3201 CN3202 CN3203 CN3204 CN3205
1-779-064-11 1-785-283-21 1-573-347-11 1-766-336-21 1-784-424-21
PIN, CONNECTOR (PC BOARD) 12P PIN, CONNECTOR (PC BOARD) 14P CONNECTOR, FFC/FPC (ZIF) 7P CONNECTOR, FFC/FPC 6P CONNECTOR, FFC/FPC (ZIF) 51P
< BATTERY > BT3201 1-528-724-21 BATTERY, V/L RECHARGEABLE < CAPACITOR >
CN3206 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P C3201 C3203
< DIODE > D3201 D3202 D3203 D3204
8-719-062-16 8-719-062-16 8-719-062-16 8-719-062-16
DIODE DIODE DIODE DIODE
01ZA8.2(TPL3) 01ZA8.2(TPL3) 01ZA8.2(TPL3) 01ZA8.2(TPL3)
1-104-913-11 TANTAL. CHIP 1-104-919-11 TANTAL. CHIP
10uF 10uF
20% 20%
16V 25V (TRV20E)
< CONNECTOR > CN3201 CN3202 CN3203 CN3204 CN3205
< RESISTOR > R3201 R3202 R3203 R3204 R3205
1-216-295-91 1-218-969-11 1-218-969-11 1-218-969-11 1-218-963-11
SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP
0 22K 22K 22K 6.8K
5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W
R3206 R3207 R3208 R3209 R3210
1-218-963-11 1-218-963-11 1-218-959-11 1-218-959-11 1-218-959-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
6.8K 6.8K 3.3K 3.3K 3.3K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R3211 R3212 R3213 R3214 R3215
1-218-955-11 1-218-955-11 1-218-955-11 1-218-954-11 1-218-954-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
1.5K 1.5K 1.5K 1.2K 1.2K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R3216 R3217
1-218-954-11 RES-CHIP 1-218-953-11 RES-CHIP
1.2K 1K
5% 5%
1/16W 1/16W
1-779-064-11 1-785-283-21 1-573-347-11 1-766-336-21 1-784-424-21
PIN, CONNECTOR (PC BOARD) 12P PIN, CONNECTOR (PC BOARD) 14P CONNECTOR, FFC/FPC (ZIF) 7P CONNECTOR, FFC/FPC 6P CONNECTOR, FFC/FPC (ZIF) 51P
CN3206 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P < DIODE > D3201 D3202 D3203 D3204
8-719-062-16 8-719-062-16 8-719-062-16 8-719-062-16
DIODE DIODE DIODE DIODE
01ZA8.2(TPL3) 01ZA8.2(TPL3) 01ZA8.2(TPL3) 01ZA8.2(TPL3)
< RESISTOR >
< SWITCH > S3201 S3202 S3203 S3204 S3205
1-762-805-21 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61
SWITCH, PUSH (1 KEY) (PANEL CLOSE) SWITCH, KEY BOARD (FADER) SWITCH, KEY BOARD (MEMORY INDEX) SWITCH, KEY BOARD (BACK LIGHT) SWITCH, KEY BOARD (MEMORY PLAY)
6-12
R3201 R3202 R3203 R3204 R3205
1-216-295-91 1-218-969-11 1-218-969-11 1-218-969-11 1-218-963-11
SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP
0 22K 22K 22K 6.8K
5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W
R3206 R3207 R3208 R3209 R3210
1-218-963-11 1-218-963-11 1-218-959-11 1-218-959-11 1-218-959-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
6.8K 6.8K 3.3K 3.3K 3.3K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R3211 R3212 R3213 R3214 R3215
1-218-955-11 1-218-955-11 1-218-955-11 1-218-954-11 1-218-954-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
1.5K 1.5K 1.5K 1.2K 1.2K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
CK-94 Ref. No. R3216 R3217
Part No.
Description
1-218-954-11 RES-CHIP 1-218-953-11 RES-CHIP
Remarks 1.2K 1K
5% 5%
Ref. No.
1/16W 1/16W
< SWITCH > S3201 S3202 S3203 S3204 S3205
1-762-805-21 SWITCH, PUSH (1 KEY) (PANEL CLOSE) 1-771-138-61 SWITCH, KEY BOARD (FADER) 1-771-138-61 SWITCH, KEY BOARD (MEMORY INDEX) (TRV20E) 1-771-138-61 SWITCH, KEY BOARD (BACK LIGHT) 1-771-138-61 SWITCH, KEY BOARD (MEMORY PLAY) (TRV20E)
S3206 S3207 S3208 S3209 S3210
1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61
SWITCH, KEY BOARD (MEMORY +) (TRV20E) SWITCH, KEY BOARD (DIGITAL EFFECT) SWITCH, KEY BOARD (SELF TIMER) SWITCH, KEY BOARD (MEMORY -) (TRV20E) SWITCH, KEY BOARD (TITLE)
S3211 S3212 S3213 S3214 S3215
1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61 1-771-138-61
SWITCH, KEY BOARD (END SEARCH) SWITCH, KEY BOARD (MEMORY MIX)(TRV20E) SWITCH, KEY BOARD (PB ZOOM) SWITCH, KEY BOARD (DATA CODE) SWITCH, KEY BOARD (MEMORY DELETE) (TRV20E)
S3216 1-771-138-61 SWITCH, KEY BOARD (MENU) S3217 1-771-138-61 SWITCH, KEY BOARD (DISPLAY) S3218 1-771-138-61 SWITCH, KEY BOARD (RESET) ************************************************************ A-7074-307-A DD-137(H) BOARD, COMPLETE (TRV20/TRV20E) ************************* A-7074-392-A DD-137(L) BOARD, COMPLETE (TRV6/TRV6E) ************************* A-7074-365-A DD-137(M) BOARD, COMPLETE (TRV11/TRV11E) ************************* (Ref.No.;10000Series)
Part No.
Description
C1622 C1623 C1624 C1625 C1626
1-109-982-11 1-127-760-91 1-127-760-91 1-164-939-11 1-109-982-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
C1627 C1628 C1629 C1630 C1631
1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V (TRV11/TRV11E/TRV20/TRV20E) 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V
C1632 C1633 C1634 C1635
1-164-940-11 1-115-566-11 1-115-566-11 1-115-566-11
1-107-819-11 1-125-777-11 1-107-819-11 1-107-819-11 1-164-939-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
C1607 C1608 C1609 C1610 C1611
1-125-777-11 1-104-913-11 1-164-874-11 1-104-913-11 1-164-935-11
CERAMIC CHIP 0.1uF 10% 10V TANTAL. CHIP 10uF 20% 16V CERAMIC CHIP 100PF 5% 16V TANTAL. CHIP 10uF 20% 16V CERAMIC CHIP 470PF 10% 16V (TRV11/TRV11E/TRV20/TRV20E)
C1612 C1613 C1614 C1615 C1616
1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16V 1-104-913-11 TANTAL. CHIP 10uF 20% 16V (TRV11/TRV11E/TRV20/TRV20E) 1-119-751-11 TANTAL. CHIP 22uF 20% 16V 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V 1-119-751-11 TANTAL. CHIP 22uF 20% 16V
C1617 C1618 C1619 C1620 C1621
1-164-939-11 1-164-935-11 1-164-937-11 1-164-933-11 1-164-874-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.022uF 0.1uF 0.022uF 0.022uF 0.0022uF
0.0022uF 470PF 0.001uF 220PF 100PF
10% 10% 10% 10% 10%
10% 10% 10% 10% 5%
16V 10V 16V 16V 16V
16V 16V 16V 16V 16V
6-13
Remarks 1uF 4.7uF 4.7uF 0.0022uF 1uF
10% 10% 10% 10% 10%
10V 6.3V 6.3V 16V 10V
C1636
CERAMIC CHIP 0.0033uF 10% 16V CERAMIC CHIP 4.7uF 10% 10V CERAMIC CHIP 4.7uF 10% 10V CERAMIC CHIP 4.7uF 10% 10V (TRV11/TRV11E/TRV20/TRV20E) 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C1637 C1638 C1639 C1640 C1641
1-115-566-11 1-162-970-11 1-104-851-11 1-127-760-91 1-127-760-91
C1642 C1643 C1644 C1645 C1646
1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V (TRV11/TRV11E/TRV20/TRV20E) 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C1647 C1648 C1649 C1650 C1651
1-164-505-11 1-109-982-11 1-164-505-11 1-165-319-11 1-131-862-91
C1651
1-135-259-11 TANTAL. CHIP
C1652
1-135-259-11 TANTAL. CHIP
C1653 C1654
1-135-259-11 TANTAL. CHIP 1-119-750-11 TANTAL. CHIP
C1654
1-135-259-11 TANTAL. CHIP
C1655 C1656 C1657 C1658
1-164-505-11 1-135-259-11 1-104-851-11 1-135-259-11
CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP
< CAPACITOR > C1601 C1602 C1603 C1604 C1605
DD-137
4.7uF 0.01uF 10uF 4.7uF 4.7uF
2.2uF 1uF 2.2uF 0.1uF 47uF
10% 10% 20% 10% 10%
10V 25V 10V 6.3V 6.3V
16V 10V 16V 50V 20% 4V (TRV11/TRV11E)
10%
10uF 20% 6.3V (TRV6/TRV6E/TRV20/TRV20E) 10uF 20% 6.3V (TRV11/TRV11E/TRV20/TRV20E) 10uF 20% 6.3V 22uF 20% 6.3V (TRV6/TRV6E/TRV11/TRV11E) 10uF 20% 6.3V (TRV20/TRV20E)
C1659
CERAMIC CHIP 2.2uF 16V TANTAL. CHIP 10uF 20% 6.3V TANTAL. CHIP 10uF 20% 10V TANTAL. CHIP 10uF 20% 6.3V (TRV11/TRV11E/TRV20/TRV20E) 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C1660 C1661 C1662 C1663 C1664
1-135-259-11 1-104-851-11 1-104-851-11 1-125-777-11 1-104-851-11
TANTAL. CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP
C1666 C1667 C1668 C1669
1-113-985-11 1-164-505-11 1-164-505-11 1-125-777-11
TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
C1672
1-113-987-11 TANTAL. CHIP
10uF 10uF 10uF 0.1uF 10uF
20% 20% 20% 10% 20%
6.3V 10V 10V 10V 10V
10uF 20% 20V 2.2uF 16V 2.2uF 16V 0.1uF 10% 10V (TRV6/TRV6E/TRV11/TRV11E) 4.7uF 20% 25V
DD-137 Ref. No. C1673 C1674
Part No.
Description
Remarks
1-104-851-11 TANTAL. CHIP 1-164-943-11 CERAMIC CHIP
10uF 0.01uF
20% 10%
Ref. No.
10V 16V
L1616 L1617 L1618 L1619
< CONNECTOR > * CN1601 1-580-056-21 * CN1602 1-580-056-21 CN1603 1-779-520-11 CN1604 1-784-421-11
PIN, CONNECTOR (SMD) 3P PIN, CONNECTOR (SMD) 3P CONNECTOR, BOARD TO BOARD 80P CONNECTOR, FFC/FPC (ZIF) 27P
L1624
Part No.
Description
Remarks
1-469-522-91 1-414-400-11 1-469-058-11 1-414-770-91
INDUCTOR 1uH INDUCTOR 22uH INDUCTOR CHIP 22uH INDUCTOR CHIP 4.7uH (TRV11/TRV11E/TRV20/TRV20E) 1-414-770-91 INDUCTOR CHIP 4.7uH (TRV20/TRV20E) < LINE FILTER >
LF1601 1-411-957-11 FILTER, COMMON MODE < DIODE > < TRANSISTOR > D1601 D1602 D1604 D1606 D1607
8-719-158-49 8-719-062-16 8-719-056-48 8-719-058-24 8-719-058-24
DIODE DIODE DIODE DIODE DIODE
MA8120-TX 01ZA8.2(TPL3) 1SS388(TPL3) RB501V-40TE-17 RB501V-40TE-17
D1608 D1609 D1610 D1611 D1612
8-719-058-24 8-719-056-48 8-719-056-48 8-719-027-77 8-719-056-48
DIODE DIODE DIODE DIODE DIODE
RB501V-40TE-17 1SS388(TPL3) 1SS388(TPL3) MA796-TX 1SS388(TPL3) (TRV20/TRV20E)
D1613 D1614 D1615 D1616
8-719-056-48 8-719-056-23 8-719-075-12 8-719-056-23
DIODE DIODE DIODE DIODE
1SS388(TPL3) MA2S111-(K8).SO MA3XD21001S0 MA2S111-(K8).SO
< FUSE > 0 F1601 0 F1602 0 F1603 0 F1604 0 F1605
1-576-406-21 1-576-406-21 1-576-406-21 1-576-406-21 1-576-406-21
0 F1606
1-576-406-21 FUSE, MICRO (1608) (1.4A 32V)
FUSE, MICRO (1608) (1.4A 32V) FUSE, MICRO (1608) (1.4A 32V) FUSE, MICRO (1608) (1.4A 32V) FUSE, MICRO (1608) (1.4A 32V) FUSE, MICRO (1608) (1.4A 3.2V) (TRV11/TRV11E/TRV20/TRV20E)
< IC > IC1601 IC1602
8-759-678-75 IC MB4488PFV-G-BND-ER-F 8-759-075-66 IC TA75S01F(TE85R) < COIL >
L1601 L1602 L1603 L1604
1-416-669-11 1-416-670-11 1-416-669-11 1-416-669-11
INDUCTOR INDUCTOR INDUCTOR INDUCTOR
L1605
1-416-669-11 INDUCTOR
L1606 L1607
1-416-669-11 INDUCTOR 1-414-392-21 INDUCTOR
L1608 L1609 L1610
1-414-392-21 INDUCTOR 1-412-056-11 INDUCTOR 1-414-392-21 INDUCTOR
L1611 L1612 L1613 L1614 L1615
1-414-392-21 1-414-770-91 1-414-770-91 1-469-522-91 1-469-522-91
22uH 33uH 22uH 22uH (TRV11/TRV11E/TRV20/TRV20E) 22uH 22uH 1uH (TRV11/TRV11E/TRV20/TRV20E) 1uH 4.7uH 1uH
INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR INDUCTOR
1uH 4.7uH 4.7uH 1uH 1uH
6-14
Q1601 Q1602 Q1603 Q1604 Q1605
8-729-047-68 8-729-046-77 8-729-804-41 8-729-037-74 8-729-050-24
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
SSM3K03FE(TPL3) SI4963DY-T1 2SB1122-ST-TD UN9213J-(K8).SO MCH6202-TL
Q1606 Q1607 Q1608 Q1609 Q1610
8-729-037-53 8-729-037-74 8-729-050-23 8-729-046-98 8-729-046-98
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SB1462J-QR(K8).SO UN9213J-(K8).SO MCH6103-TL CPH6702-TL CPH6702-TL
Q1611 Q1612
8-729-046-98 TRANSISTOR 8-729-046-98 TRANSISTOR
Q1613 Q1614 Q1615
CPH6702-TL CPH6702-TL (TRV11/TRV11E/TRV20/TRV20E) 8-729-046-98 TRANSISTOR CPH6702-TL 8-729-046-98 TRANSISTOR CPH6702-TL 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO
Q1616 Q1617 Q1618 Q1619 Q1620
8-729-017-61 8-729-037-53 8-729-044-58 8-729-044-58 8-729-044-58
Q1621
8-729-044-58 TRANSISTOR
Q1622 Q1623 Q1624 Q1625
8-729-044-58 8-729-044-58 8-729-037-52 8-729-037-74
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
Q1626 Q1627 Q1628 Q1629 Q1632
8-729-042-56 8-729-049-91 8-729-037-52 8-729-037-74 8-729-037-53
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
MGSF3455VT1 2SA2018H-T2L 2SD2216J-QR(K8).SO UN9213J-(K8).SO 2SB1462J-QR(K8).SO
Q1635 Q1637 Q1639 Q1641 Q1643
8-729-037-53 8-729-037-52 8-729-037-52 8-729-037-53 8-729-037-53
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SB1462J-QR(K8).SO 2SD2216J-QR(K8).SO 2SD2216J-QR(K8).SO 2SB1462J-QR(K8).SO 2SB1462J-QR(K8).SO
Q1646
8-729-037-74 TRANSISTOR
Q1647
8-729-037-52 TRANSISTOR
Q1648
8-729-037-74 TRANSISTOR
Q1649
8-729-037-52 TRANSISTOR
Q1650
8-729-037-53 TRANSISTOR
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
2SB1581-T1 2SB1462J-QR(K8).SO SI2304DS-T1 SI2304DS-T1 SI2304DS-T1 SI2304DS-T1 (TRV11/TRV11E/TRV20/TRV20E) SI2304DS-T1 SI2304DS-T1 2SD2216J-QR(K8).SO UN9213J-(K8).SO
UN9213J-(K8).SO (TRV20/TRV20E) 2SD2216J-QR(K8).SO (TRV6/TRV6E/TRV11/TRV11E) UN9213J-(K8).SO (TRV20/TRV20E) 2SD2216J-QR(K8).SO (TRV6/TRV6E/TRV11/TRV11E) 2SB1462J-QR(K8).SO (TRV6/TRV6E/TRV11/TRV11E) Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DD-137 Ref. No. Q1653
Part No.
Description
8-729-037-52 TRANSISTOR
Remarks
Ref. No.
2SD2216J-QR(K8).SO (TRV6/TRV6E/TRV11/TRV11E)
< RESISTOR > R1601 R1602 R1603 R1604 R1605
1-218-953-11 1-218-985-11 1-218-989-11 1-216-150-91 1-218-953-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
R1606 R1609
1-218-961-11 RES-CHIP 1-218-990-11 SHORT
1K 470K 1M 10 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/8W 1/16W
R1610 R1611 R1612
4.7K 5% 1/16W 0 (TRV11/TRV11E/TRV20/TRV20E) 1-218-961-11 RES-CHIP 4.7K 5% 1/16W 1-218-969-11 RES-CHIP 22K 5% 1/16W 1-208-715-11 METAL CHIP 22K 0.5% 1/16W
R1613
1-208-927-11 METAL CHIP
R1614
1-218-969-11
R1615 R1616 R1617
1-218-965-11 1-208-707-11 1-208-931-11
R1618 R1619
1-218-970-11 RES-CHIP 1-218-849-11 METAL CHIP
47K 0.5% 1/16W (TRV11/TRV11E/TRV20/TRV20E) RES-CHIP 22K 5% 1/16W (TRV11/TRV11E/TRV20/TRV20E) RES-CHIP 10K 5% 1/16W METAL CHIP 10K 0.5% 1/16W METAL CHIP 68K 0.5% 1/16W (TRV11/TRV11E/TRV20/TRV20E)
R1620 R1621 R1622
27K 5% 1/16W 3.3K 0.5% 1/16W (TRV11/TRV11E/TRV20/TRV20E) 1-218-973-11 RES-CHIP 47K 5% 1/16W 1-218-965-11 RES-CHIP 10K 5% 1/16W 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R1623 R1624 R1625 R1626 R1627
1-218-969-11 1-208-927-11 1-218-965-11 1-218-971-11 1-208-715-11
RES-CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP
R1628 R1629 R1630 R1631
1-218-974-11 1-218-974-11 1-208-715-11 1-208-933-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
R1631
1-208-935-11 METAL CHIP
R1632 R1633 R1634 R1635 R1636
1-218-945-11 1-218-849-11 1-208-697-11 1-208-697-11 1-208-707-11
R1636
1-208-711-11 METAL CHIP
R1637
1-218-941-11 RES-CHIP
R1638 R1639 R1640
1-218-941-11 RES-CHIP 1-218-941-11 RES-CHIP 1-218-941-11 RES-CHIP
R1641 R1642 R1643 R1644 R1645
1-218-953-11 1-218-953-11 1-218-941-11 1-218-941-11 1-218-973-11
RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
22K 47K 10K 33K 22K
5% 0.5% 5% 5% 0.5%
1/16W 1/16W 1/16W 1/16W 1/16W
56K 0.5% 1/16W 56K 0.5% 1/16W 22K 0.5% 1/16W 82K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 100K 0.5% 1/16W (TRV20/TRV20E) 220 3.3K 3.9K 3.9K 10K
5% 1/16W 0.5% 1/16W 0.5% 1/16W 0.5% 1/16W 0.5% 1/16W (TRV20/TRV20E)
15K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 100 5% 1/16W (TRV11/TRV11E/TRV20/TRV20E) 100 5% 1/16W 100 5% 1/16W 100 5% 1/16W 1K 1K 100 100 47K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
6-15
Part No.
Description
R1646 R1647 R1648 R1649 R1650
1-218-965-11 1-208-715-11 1-208-719-11 1-218-965-11 1-218-989-11
RES-CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP
R1651
1-218-990-11 SHORT
R1652 R1653 R1654 R1655
1-218-977-11 1-218-973-11 1-218-969-11 1-218-949-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP
R1656 R1657 R1658 R1661 R1662
1-218-969-11 1-208-719-11 1-208-936-81 1-218-977-11 1-218-977-11
RES-CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP
R1664 R1666 R1668
1-218-969-11 RES-CHIP 1-218-969-11 RES-CHIP 1-218-990-11 SHORT
R1669 R1672
1-218-990-11 SHORT 1-208-927-11 METAL CHIP
R1673 R1674 R1675 R1676
1-218-982-11 1-208-935-11 1-208-935-11 1-208-707-11
R1676
1-208-715-11 METAL CHIP
R1677 R1678 R1679 R1680
1-208-943-11 1-218-849-11 1-218-990-11 1-218-973-11
R1682
1-218-953-11 RES-CHIP
R1683
1-218-952-11 RES-CHIP
R1684
1-218-977-11 RES-CHIP
R1685
1-218-969-11 RES-CHIP
R1686
1-218-969-11 RES-CHIP
R1687
1-218-952-11 RES-CHIP
R1688
1-218-952-11 RES-CHIP
R1689
1-208-713-11 METAL CHIP
R1690
1-208-935-11 METAL CHIP
R1691
1-208-927-11 METAL CHIP
R1692
1-218-952-11 RES-CHIP
R1693 R1694 R1695 R1696 R1697
1-217-671-11 1-217-671-11 1-218-982-11 1-218-973-11 1-218-969-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
METAL CHIP METAL CHIP SHORT RES-CHIP
METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP
Remarks 10K 22K 33K 10K 1M
5% 0.5% 0.5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
0 (TRV6/TRV6E/TRV11/TRV11E) 100K 5% 1/16W 47K 5% 1/16W 22K 5% 1/16W 470 5% 1/16W 22K 33K 110K 100K 100K
5% 0.5% 0.5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
22K 5% 1/16W 22K 5% 1/16W 0 (TRV6/TRV6E/TRV11/TRV11E) 0 (TRV20/TRV20E) 47K 0.5% 1/16W 270K 100K 100K 10K
0.5% 1/16W 0.5% 1/16W 0.5% 1/16W 0.5% 1/16W (TRV20/TRV20E) 22K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 220K 0.5% 1/16W 1.2K 0.5% 1/16W 0 47K 5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 1K 5% 1/16W 820
5% 1/16W (TRV20/TRV20E) 100K 5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 22K 5% 1/16W (TRV20/TRV20E) 22K 5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 820 5% 1/16W (TRV20/TRV20E) 820
5% 1/16W (TRV20/TRV20E) 18K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 100K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 47K 0.5% 1/16W (TRV6/TRV6E/TRV11/TRV11E) 820 5% 1/16W (TRV20/TRV20E) 1 1 270K 47K 22K
5% 5% 5% 5% 5%
1/10W 1/10W 1/16W 1/16W 1/16W
DD-137 Ref. No. R1698 R1699 R1700 R1701 R1702
FP-102
Part No.
Description
1-218-969-11 1-218-969-11 1-218-969-11 1-218-969-11 1-218-953-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
FP-219
JK-188 Remarks
22K 22K 22K 22K 1K
5% 5% 5% 5% 5%
Ref. No.
1/16W 1/16W 1/16W 1/16W 1/16W
C3063 C3064 C3065 C3066 C3067
Part No.
Description
1-125-817-11 1-125-817-11 1-110-501-11 1-104-847-11 1-125-777-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP
< TRANSFORMER >
10% 10% 10% 20% 10%
6.3V 6.3V 16V 4V 10V
< CONNECTOR >
T1601 1-435-456-21 TRANSFORMER, DC-DC CONVERTER T1602 1-435-456-21 TRANSFORMER, DC-DC CONVERTER ************************************************************
D901
Remarks 10uF 10uF 0.33uF 22uF 0.1uF
CN3001 1-784-939-11 CONNECTOR, BOARD TO BOARD 60P < DIODE >
FP-102 FLEXIBLE (Not supplied) ************************** (Ref.No.;6000Series)
D3001
< DIODE >
FB3004 FB3005 FB3007 FB3008
8-719-078-71 DIODE LN57A.SO
8-719-056-61 DIODE 015AZ8.2-TPL3 < FERRITE BEAD > 1-500-444-11 1-500-444-11 1-500-444-11 1-500-444-11
FERRITE FERRITE FERRITE FERRITE
0UH 0UH 0UH 0UH
< HOLE ELEMENT > < IC > H901 H902
8-719-067-74 DIODE HW-105A-CDE-T 8-719-067-74 DIODE HW-105A-CDE-T
IC3051
8-759-489-19 IC uPC6756GR-8JG-E2
< TRANSISTOR > Q901 Q902
8-729-028-71 TRANSISTOR 8-729-028-71 TRANSISTOR
< JACK > PN166.SO PN166.SO
J3001 J3002 J3003 J3004
< SWITCH >
1-778-518-11 1-695-514-21 1-778-040-11 1-794-276-11
S903 1-771-326-41 SWITCH, PUSH (1KEY) (CC DOWN) ************************************************************
< COIL > L3052
1-677-566-21 FP-219 FLEXIBLE, COMPLETE (TRV6/TRV6E/TRV11/TRV11E) ************************************** (Ref.No.;30000Series) (All parts excluding CCD are already mounted of the FP-219 FLEXIBLE, COMPLETE.) (IC3000 is not included in this complete board.)
CONNECTOR, EXTERNAL (S VIDEO) JACK (SMALL TYPE) 1P (i) JACK, SMALL TYPE (AUDIO/VIDEO) CONNECTOR, SQUARE TYPE 4P (DV IN/OUT)
1-414-771-91 INDUCTOR CHIP 10uH < RESISTOR >
R3001 R3002 R3003 R3004 R3005
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 0 0 0
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R3051 R3052 R3053 R3054 R3055
1-218-969-11 1-218-969-11 1-218-969-11 1-218-969-11 1-218-965-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
22K 22K 22K 22K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R3056 R3057 R3058 R3059 R3060
1-218-965-11 1-218-989-11 1-218-967-11 1-218-989-11 1-218-953-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
10K 1M 15K 1M 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R3061
1-216-295-91 SHORT
< IC > IC3000 A-7031-011-A CCD BLOCK ASSY (TRV6/TRV11) IC3000 A-7031-012-A CCD BLOCK ASSY (TRV6E/TRV11E) ************************************************************ A-7074-309-A JK-188 BOARD, COMPLETE ********************** (Ref.No.;10000Series) < CAPACITOR > C3053 C3054 C3055 C3056 C3057
1-104-847-11 1-104-847-11 1-125-777-11 1-125-777-11 1-119-923-81
TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
22uF 22uF 0.1uF 0.1uF 0.047uF
20% 20% 10% 10% 10%
4V 4V 10V 10V 10V
C3058 C3059 C3060 C3061 C3062
1-119-923-81 1-119-923-81 1-119-923-81 1-125-817-11 1-125-817-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.047uF 0.047uF 0.047uF 10uF 10uF
10% 10% 10% 10% 10%
10V 10V 10V 6.3V 6.3V
0
< SENSOR > SE3051 1-803-042-31 SENSOR, ANGULAR VELOCITY (PITCH) SE3052 1-803-042-41 SENSOR, ANGULAR VELOCITY (YAW) < VARISTOR > VDR001 VDR002 VDR003 VDR004 VDR005
Be sure to read “Precautions upon replacing CCD imager” on page 4-14 when changing the CCD imager.
6-16
1-801-862-11 1-801-862-11 1-801-862-11 1-801-862-11 1-803-742-21
VARISTOR, CHIP VARISTOR, CHIP VARISTOR, CHIP VARISTOR, CHIP VARISTOR, CHIP
JK-188 Ref. No.
Part No.
Description
Remarks
Ref. No.
VDR006 1-803-742-21 VARISTOR, CHIP VDR007 1-803-742-21 VARISTOR, CHIP ************************************************************ A-7074-310-A LB-64 BOARD, COMPLETE ********************* (Ref.No.;10000Series) < CAPACITOR > C2201 C2202 C2203 0 C2204
1-125-777-11 1-113-682-11 1-115-566-11 1-115-464-91
CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 33uF 4.7uF 0.0022uF
10% 20% 10% 10%
10V 10V 10V 630V
< CONNECTOR > CN2201 1-784-421-11 CONNECTOR, FFC/FPC (ZIF) 27P CN2201 1-784-421-11 CONNECTOR, FPC (ZIF) 27P CN2202 1-691-380-21 CONNECTOR, FFC/FPC 16P < IC > IC2201
1-412-031-11 INDUCTOR CHIP 47uH 1-469-525-91 INDUCTOR 10uH < FLUORESCENT INDICATOR >
0 ND2201 1-517-933-31 FLUORESCENT TUBE (0.44) < TRANSISTOR > 0 Q2201
8-729-039-24 TRANSISTOR
Part No.
Description
C2015 C2017 C2018 C2020 C2021
1-164-937-11 1-164-874-11 1-164-874-11 1-125-777-11 1-125-777-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 100PF 100PF 0.1uF 0.1uF
10% 5% 5% 10% 10%
16V 16V 16V 10V 10V
C2022 C2023 C2024 C2025 C2026
1-125-777-11 1-110-563-11 1-125-777-11 1-110-563-11 1-164-227-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.068uF 0.1uF 0.068uF 0.022uF
10% 10% 10% 10% 10%
10V 16V 10V 16V 25V
C2027 C2028 C2029 C2031 C2032
1-164-227-11 1-164-245-11 1-164-940-11 1-164-940-11 1-164-245-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.022uF 0.015uF 0.0033uF 0.0033uF 0.015uF
10% 10% 10% 10% 10%
25V 25V 16V 16V 25V
C2036 C2037 C2038 C2039 C2041
1-125-777-11 1-117-919-11 1-165-128-11 1-125-841-91 1-164-937-11
CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP
0.1uF 10uF 0.22uF 22uF 0.001uF
10% 20% 20% 10%
10V 6.3V 16V 4V 16V
C2042 C2043 C2044 C2045 C2046
1-164-937-11 1-164-939-11 1-125-777-11 1-125-777-11 1-125-777-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 0.0022uF 0.1uF 0.1uF 0.1uF
10% 10% 10% 10% 10%
16V 16V 10V 10V 10V
C2047 C2071 C2072 C2073 C2091
1-125-777-11 1-107-826-91 1-104-913-11 1-107-826-91 1-117-919-11
CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP
0.1uF 0.1uF 10uF 0.1uF 10uF
10% 10% 20% 10% 20%
10V 16V 16V 16V 6.3V
Remarks
< CONNECTOR >
FX216-TL1
CN2001 1-778-507-21 PIN, CONNECTOR (PC BOARD) 4P CN2051 1-778-793-21 CONNECTOR, FFC/FPC (ZIF) 5P CN2071 1-764-534-21 CONNECTOR, FFC/FPC (ZIF) 28P
< RESISTOR > R2203 R2205
MA-385
8-759-485-79 IC TC7SET08FU(TE85R) < COIL >
L2201 L2202
LB-64
1-216-808-11 METAL CHIP 1-218-965-11 RES-CHIP
82 10K
5% 5%
1/16W 1/16W
< DIODE > < TRANSFORMER > 0 T2201 1-435-225-21 TRANSFORMER, INVERTER ************************************************************ A-7074-308-A MA-385 BOARD, COMPLETE *********************** (Ref.No.;10000Series) 3-061-599-01 HOLDER (3015), LED
*
D2001 D2002 D2061 D2062 D2063
8-719-062-16 8-719-062-16 8-719-061-82 8-719-062-16 8-719-072-91
DIODE DIODE DIODE DIODE DIODE
01ZA8.2(TPL3) 01ZA8.2(TPL3) TLSU1002(TPX1,SONY) 01ZA8.2(TPL3) MAZJ200D0LS0
D2071 D2072 D2091
8-719-060-65 DIODE DAC3825 8-719-078-23 DIODE DCR2815 8-719-056-23 DIODE MA2S111-(K8).SO < FERRITE BEAD >
< CAPACITOR > C2005 C2006 C2007 C2008 C2009
1-107-819-11 1-164-941-11 1-107-819-11 1-164-943-11 1-164-941-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.022uF 0.0047uF 0.022uF 0.01uF 0.0047uF
10% 10% 10% 10% 10%
16V 16V 16V 16V 16V
C2010 C2011 C2012 C2013 C2014
1-117-919-11 1-164-937-11 1-117-919-11 1-164-874-11 1-164-874-11
TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP
10uF 0.001uF 10uF 100PF 100PF
20% 10% 20% 5% 5%
6.3V 16V 6.3V 16V 16V
FB2001 FB2002 FB2003 FB2061
1-500-444-11 1-500-444-11 1-500-444-11 1-216-864-11
FERRITE FERRITE FERRITE METAL CHIP
0UH 0UH 0UH 0
FB2062 1-500-444-11 FERRITE
0UH
FB2063 1-500-444-11 FERRITE FB2064 1-500-444-11 FERRITE
0UH 0UH
5%
1/16W (Note)
Note : Resistor is mounted to the location where FB2061 is printed.
6-17
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
MA-385 Ref. No.
NS-10
Part No.
PD-123
Description
Remarks
Ref. No.
< IC > IC2002 IC2091
8-759-638-50 IC AN2901FHQ-EB 8-749-013-13 IC RS-70-TU
Part No.
Description
R2065 R2071 R2072 R2073 R2074
1-218-949-11 1-218-932-11 1-216-001-00 1-218-973-11 1-218-953-11
RES-CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP
R2075 R2091
1-216-795-11 RES-CHIP 1-218-937-11 RES-CHIP
Remarks 470 18 10 47K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/10W 1/16W 1/16W
6.8 47
5% 5%
1/16W 1/16W
< JACK > J2001 J2002
1-691-737-11 JACK (SMALL TYPE) (MIC) 1-793-995-11 JACK, SUPER SMALL TYPE (DIGITAL I/O) (LANC)
< SWITCH >
< COIL > L2001
1-414-754-11 INDUCTOR
S2061
< VARISTOR >
10uH
< TRANSISTOR > Q2071 Q2072 Q2073 Q2074
8-729-140-75 8-729-141-48 8-729-037-72 8-729-037-53
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
1-762-651-11 SWITCH, SLIDE
VDR201 1-803-742-21 VARISTOR, CHIP ************************************************************ 2SD999-T1-CLCK 2SB624-T1BV4 UN9211J-(TX).SO 2SB1462J-QR(TX).SO
A-7074-312-A NS-10 BOARD, COMPLETE (TRV20/TRV20E) *********************************** (Ref.No.;4000Series) < SWITCH >
< RESISTOR >
S001 1-771-138-61 SWITCH, KEY BOARD (SLOW SHUTTER) ************************************************************
R2007 R2008 R2009 R2010 R2011
1-218-968-11 1-218-971-11 1-218-961-11 1-218-965-11 1-218-957-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
18K 33K 4.7K 10K 2.2K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R2012 R2013 R2014 R2015 R2016
1-218-957-11 1-218-963-11 1-218-963-11 1-218-953-11 1-218-953-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
2.2K 6.8K 6.8K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R2017 R2018 R2019 R2020 R2021
1-218-957-11 1-218-957-11 1-208-910-11 1-218-969-11 1-208-910-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
2.2K 2.2K 9.1K 22K 9.1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
C2101 C2102 C2105 C2106 C2107
1-113-988-11 1-125-777-11 1-164-943-11 1-164-943-11 1-164-943-11
TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
68uF 0.1uF 0.01uF 0.01uF 0.01uF
20% 10% 10% 10% 10%
4V 10V 16V 16V 16V
R2022 R2023 R2024 R2025 R2026
1-218-969-11 1-218-970-11 1-218-990-11 1-218-990-11 1-218-970-11
RES-CHIP RES-CHIP SHORT SHORT RES-CHIP
22K 27K 0 0 27K
5% 5%
1/16W 1/16W
5%
1/16W
C2108 C2109 C2110 C2111 C2112
1-135-259-11 1-125-777-11 1-125-777-11 1-107-687-11 1-107-826-91
TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP
10uF 0.1uF 0.1uF 3.3uF 0.1uF
20% 10% 10% 20% 10%
6.3V 10V 10V 20V 16V
R2027 R2028 R2031 R2032 R2033
1-218-969-11 1-218-969-11 1-218-971-11 1-218-954-11 1-218-971-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
22K 22K 33K 1.2K 33K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
C2113 C2114 C2115 C2116 C2117
1-164-739-11 1-125-777-11 1-125-777-11 1-104-851-11 1-164-357-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP
560PF 0.1uF 0.1uF 10uF 1000PF
5% 10% 10% 20% 5%
50V 10V 10V 10V 50V
R2034 R2035 R2036 R2037 R2038
1-218-968-11 1-218-990-11 1-208-912-11 1-208-912-11 1-208-701-11
RES-CHIP SHORT METAL CHIP METAL CHIP METAL CHIP
18K 0 11K 11K 5.6K
5%
1/16W
C2118
1-164-866-11 CERAMIC CHIP
47PF
5%
0.5% 0.5% 0.5%
1/16W 1/16W 1/16W
C2118
1-164-872-11 CERAMIC CHIP
82PF
R2051 R2052 R2062 R2063 R2064
1-218-945-11 1-218-945-11 1-218-966-11 1-218-969-11 1-218-952-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
220 220 12K 22K 820
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
C2119 C2120 C2121
1-109-982-11 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP
1uF 1uF 1uF
C2122 C2123 C2124 C2125 C2127
1-113-994-11 1-125-777-11 1-125-777-11 1-107-682-11 1-135-177-21
6.8uF 0.1uF 0.1uF 1uF 1uF
A-7074-314-A PD-123(CA) BOARD, COMPLETE (TRV20) ********************************* A-7074-367-A PD-123 (SH) BOARD, COMPLETE (TRV11/TRV11E) ************************************** (Ref.No.;20000Series) < CAPACITOR >
6-18
TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP
16V (TRV20) 5% 16V (TRV11/TRV11E) 10% 10V 10% 10V 10% 10V 20% 16V 10% 10V 10% 10V 10% 16V 20% 20V (TRV11/TRV11E)
PD-123 Ref. No.
Part No.
Description
C2128 C2129 C2130 C2131
1-107-826-91 1-164-943-11 1-107-682-11 1-164-943-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.01uF 1uF 0.01uF
C2132
1-164-943-11 CERAMIC CHIP
0.01uF
C2172 C2173 C2174 C2175 C2180
1-127-985-91 1-107-826-91 1-117-919-11 1-125-777-11 1-162-970-11
47uF 0.1uF 10uF 0.1uF 0.01uF
TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP
Remarks
Ref. No.
1-750-344-11 1-785-283-21 1-785-554-21 1-784-420-11 1-779-064-11
Description
Remarks
R2101 R2103 R2105 R2106 R2107
1-218-990-11 1-218-990-11 1-218-985-11 1-208-719-11 1-218-970-11
SHORT SHORT RES-CHIP METAL CHIP METAL CHIP
0 0 470K 33K 27K
(TRV20) (TRV11/TRV11E) 5% 1/16W 0.5% 1/16W 0.5% 1/16W
20% 10% 20% 10% 10%
R2111 R2112 R2113 R2114 R2116
1-218-977-11 1-216-835-11 1-218-958-11 1-218-973-11 1-218-975-11
RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP
100K 15K 2.7K 47K 68K
5% 5% 5% 5% 5%
R2117 R2118 R2119 R2120 R2121
1-218-969-11 1-218-975-11 1-218-989-11 1-218-977-11 1-218-989-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
22K 68K 1M 100K 1M
5% 1/16W 5% 1/16W 5% 1/16W 5% 1/16W 5% 1/16W (TRV11/TRV11E)
R2122
1-218-974-11 RES-CHIP
56K
5%
R2123 R2124 R2125 R2126
1-218-990-11 1-218-990-11 1-500-284-21 1-218-990-11
SHORT SHORT INDUCTOR CHIP SHORT
0 (TRV20) 0 (TRV11/TRV11E) 0UH (Note) 0 (TRV20)
R2127 R2129 R2133 R2134 R2135
1-218-942-11 1-218-965-11 1-218-941-11 1-218-941-11 1-218-941-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
120 10K 100 100 100
5% 5% 5% 5% 5%
R2140 R2141 R2142 R2143
1-218-990-11 1-218-965-11 1-218-985-11 1-218-980-11
SHORT RES-CHIP RES-CHIP RES-CHIP
0 10K 470K 180K
R2144
1-218-990-11 SHORT
0
(TRV20) 5% 1/16W 5% 1/16W 5% 1/16W (TRV11/TRV11E) (TRV20)
R2146 R2147
1-218-990-11 SHORT 1-218-965-11 RES-CHIP
0 10K
3.3uH (TRV11/TRV11E) 4.7uH 100uH
R2148
1-218-973-11 RES-CHIP
47K
R2149 R2150
1-218-990-11 SHORT 1-218-989-11 RES-CHIP
0 1M
MGSF1P02LT1 (TRV11/TRV11E) 2SB1462J-QR(K8).SO (TRV11/TRV11E) 2SD2216J-QR(K8).SO (TRV11/TRV11E) 2SB1462J-QR(K8).SO (TRV11/TRV11E) 2SD2216J-QR(K8).SO (TRV11/TRV11E)
R2151
1-218-989-11 RES-CHIP
1M
R2152 R2153 R2154 R2175
1-218-990-11 1-218-990-11 1-218-990-11 1-218-961-11
0 0 0 4.7K
< RESISTOR >
16V 16V 6.3V 10V 25V
< CONNECTOR > CN2101 CN2173 CN2174 CN2175 CN2176
Part No.
10% 16V 10% 16V 10% 16V 10% 16V (TRV11/TRV11E) 10% 16V (TRV11/TRV11E)
CONNECTOR, FFC/EPC (ZIF) 24P PIN, CONNECTOR (PC BOARD) 14P CONNECTOR (5P), CARD EDGE CONNECTOR, FFC/FPC (ZIF) 21P PIN, CONNECTOR (PC BOARD) 12P < DIODE >
D2101 D2102 D2103
8-719-073-01 DIODE MA111-TX 8-713-102-80 DIODE 1T369-01-T8A 8-719-073-01 DIODE MA111-TX (TRV11/TRV11E) < IC >
IC2104 IC2105 IC2105 IC2106 IC2171
8-759-660-92 8-759-591-93 8-759-660-91 8-759-478-92 8-759-573-02
IC IC IC IC IC
RB5P003AM1 CM7019L3-T4 (TRV20) LZ9FF424 (TRV11/TRV11E) TC7SET04FU(TE85R) (TRV11/TRV11E) BU9735K-E2
< COIL > L2101 L2102 L2103 L2104 L2105
1-469-525-91 1-414-771-91 1-414-771-91 1-414-771-91 1-412-943-11
INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR
L2105 L2172 L2173
1-412-945-11 INDUCTOR 1-412-056-11 INDUCTOR 1-414-757-11 INDUCTOR
10uH 10uH 10uH 10uH 2.2uH (TRV20)
< TRANSISTOR > Q2102
8-729-041-23 TRANSISTOR
Q2103
8-729-037-53 TRANSISTOR
Q2104
8-729-037-52 TRANSISTOR
Q2105
8-729-037-53 TRANSISTOR
Q2106
8-729-037-52 TRANSISTOR
Q2107 Q2108 Q2172 Q2173
8-729-037-52 8-729-037-74 8-729-042-72 8-729-037-53
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
SHORT SHORT SHORT RES-CHIP
1/16W 1/16W 1/16W 1/16W 1/16W
1/16W (TRV20)
1/16W 1/16W 1/16W 1/16W 1/16W
(TRV20) 5% 1/16W (TRV11/TRV11E) 5% 1/16W (TRV11/TRV11E) (TRV20) 5% 1/16W (TRV11/TRV11E) 5% 1/16W (TRV11/TRV11E)
5%
1/16W
R2176 1-218-953-11 RES-CHIP 1K 5% 1/16W R2177 1-216-864-11 METAL CHIP 0 5% 1/16W R2180 1-216-855-11 METAL CHIP 680K 5% 1/16W ************************************************************
2SD2216J-QR(K8).SO UN9213J-(K8).SO UN9214J-(K8).SO 2SB1462J-QR(K8).SO
Note : Inductor is mounted to the location where R2125 is printed.
6-19
PD-124 Ref. No.
Part No.
Description
Remarks
Ref. No.
A-7074-394-A PD-124(ST2) BOARD, COMPLETE (TRV6/TRV6E) ************************************** A-7074-397-A PD-124(ST3) BOARD, COMPLETE (TRV20E) ********************************** (Ref.No.;30000Series)
Part No.
Description
Remarks
< DIODE > D3101 D3102 D3103 D3104 D3105
8-719-073-01 8-713-102-80 8-719-050-39 8-719-050-44 8-719-073-01
DIODE DIODE DIODE DIODE DIODE
MA111-TX 1T369-01-T8A RD2.7UM-T1B RD3.3UM-T1B2 MA111-TX
(TRV20E) (TRV6/TRV6E)
< CAPACITOR > < IC > C3101 C3102 C3104 C3105 C3106
1-113-988-11 1-125-777-11 1-117-919-11 1-164-943-11 1-125-777-11
TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP
68uF 0.1uF 10uF 0.01uF 0.1uF
20% 10% 20% 10% 10%
4V 10V 6.3V 16V 10V
C3107 C3108 C3109 C3110 C3111
1-164-943-11 1-164-943-11 1-164-943-11 1-164-943-11 1-107-826-91
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.01uF 0.01uF 0.01uF 0.1uF
10% 10% 10% 10% 10%
16V 16V 16V 16V 16V
C3112 C3113 C3114 C3115 C3116
1-164-739-11 1-164-357-11 1-109-982-11 1-164-004-11 1-164-943-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
560PF 1000PF 1uF 0.1uF 0.01uF
5% 5% 10% 10% 10%
50V 50V 10V 25V 16V
C3117
1-164-864-11 CERAMIC CHIP
39PF
5%
C3117
1-164-866-11 CERAMIC CHIP
47PF
C3118 C3119 C3120
1-107-687-11 TANTAL. CHIP 1-109-982-11 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP
3.3uF 1uF 1uF
C3121 C3126 C3127 C3128 C3129
1-109-982-11 1-107-826-91 1-164-943-11 1-164-506-11 1-109-982-11
1uF 0.1uF 0.01uF 4.7uF 1uF
IC3101 IC3102 IC3171
8-759-660-93 IC RB5P004AM1 8-752-403-84 IC CXD3505R-T4 8-759-573-02 IC BU9735K-E2 < COIL >
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
10%
10V 16V 16V 16V 10V (TRV20E)
C3130 C3131 C3132
1-107-725-11 CERAMIC CHIP 1-107-826-91 CERAMIC CHIP 1-109-982-11 CERAMIC CHIP
0.1uF 0.1uF 1uF
C3133 C3134
1-164-876-11 CERAMIC CHIP 1-164-876-11 CERAMIC CHIP
120PF 120PF
10% 16V 10% 16V 10% 10V (TRV6/TRV6E) 5% 16V 5% 16V
C3135 C3136 C3137 C3171 C3173
1-164-876-11 1-125-777-11 1-125-777-11 1-162-970-11 1-127-985-91
120PF 0.1uF 0.1uF 0.01uF 47uF
5% 10% 10% 10% 20%
16V 10V 10V 25V 16V
C3174 C3175 C3176
1-107-826-91 CERAMIC CHIP 1-117-919-11 TANTAL. CHIP 1-125-777-11 CERAMIC CHIP
0.1uF 10uF 0.1uF
10% 20% 10%
16V 6.3V 10V
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP
< CONNECTOR > CN3101 CN3171 CN3172 CN3173 CN3174
1-750-344-11 1-779-064-11 1-785-283-21 1-784-420-11 1-785-554-21
1-414-771-91 1-414-754-11 1-414-771-91 1-412-943-11 1-412-945-11
INDUCTOR CHIP INDUCTOR INDUCTOR CHIP INDUCTOR INDUCTOR
L3171 L3172
1-412-056-11 INDUCTOR 1-414-757-11 INDUCTOR
10uH 10uH 10uH 2.2uH 3.3uH
(TRV20E) (TRV6/TRV6E)
4.7uH 100uH
< TRANSISTOR >
16V (TRV20E) 5% 16V (TRV6/TRV6E) 20% 20V 10% 10V 10% 10V 10% 10% 10%
L3101 L3102 L3103 L3104 L3104
CONNECTOR, FFC/EPC (ZIF) 24P PIN, CONNECTOR (PC BOARD) 12P PIN, CONNECTOR (PC BOARD) 14P CONNECTOR, FFC/FPC (ZIF) 21P CONNECTOR (5P), CARD EDGE
6-20
Q3102 Q3103 Q3104 Q3105 Q3106
8-729-037-74 8-729-041-23 8-729-037-53 8-729-427-74 8-729-427-74
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
UN9213J-(TX).SO NDS356AP 2SB1462J-QR(K8).SO XP4601-TXE XP4601-TXE
Q3107 Q3108 Q3171 Q3172
8-729-037-52 8-729-037-74 8-729-042-72 8-729-037-53
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SD2216J-QR(K8).SO UN9213J-(TX).SO UN9214J-(K8).SO 2SB1462J-QR(K8).SO
< RESISTOR > R3102 R3105 R3106 R3107 R3108
1-208-719-11 1-208-719-11 1-218-985-11 1-218-985-11 1-218-967-11
METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP
33K 33K 470K 470K 15K
0.5% 0.5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R3109 R3110 R3111 R3112 R3113
1-218-990-11 1-218-973-11 1-218-975-11 1-218-969-11 1-218-977-11
SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP
0 47K 68K 22K 100K
5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W
R3114 R3116 R3117 R3121 R3122
1-218-975-11 1-218-989-11 1-218-990-11 1-218-929-11 1-218-929-11
RES-CHIP RES-CHIP SHORT RES-CHIP RES-CHIP
68K 1M 0 10 10
5% 5%
1/16W 1/16W
5% 5%
1/16W 1/16W
R3123 R3124 R3125 R3126 R3127
1-218-929-11 1-218-941-11 1-218-985-11 1-218-990-11 1-218-981-11
RES-CHIP RES-CHIP RES-CHIP SHORT RES-CHIP
10 100 470K 0 220K
5% 5% 5%
1/16W 1/16W 1/16W
5%
1/16W
R3128 R3131 R3132 R3133 R3134
1-218-977-11 1-218-977-11 1-218-965-11 1-218-965-11 1-216-847-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP
100K 100K 10K 10K 150K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
Ver 1.1 2000. 06
PD-124 Ref. No.
Part No.
Description
Remarks
R3135 R3136 R3137
1-218-977-11 RES-CHIP 1-218-990-11 SHORT 1-218-974-11 RES-CHIP
100K 0 56K
5%
1/16W
5%
R3139 R3140
1-218-963-11 RES-CHIP 1-218-941-11 RES-CHIP
6.8K 100
5% 5%
1/16W (TRV20E) 1/16W 1/16W
R3141 R3142 R3143 R3144 R3146
1-218-941-11 1-218-941-11 1-218-990-11 1-218-990-11 1-220-207-81
RES-CHIP RES-CHIP SHORT SHORT RES-CHIP
100 100 0 0 110K
5% 1/16W 5% 1/16W (TRV20E) (TRV6/TRV6E) 5% 1/16W (TRV20E)
R3147 R3148 R3149 R3150 R3151
1-218-965-11 1-216-864-11 1-218-990-11 1-216-864-11 1-218-990-11
RES-CHIP METAL CHIP SHORT METAL CHIP SHORT
10K 0 0 0 0
5% 5%
1/16W 1/16W
5%
1/16W
R3152
1-208-860-81 METAL CHIP
75
0.5%
R3152 R3153
1-218-990-11 SHORT 1-208-860-81 METAL CHIP
0 75
R3153 R3154
1-218-990-11 SHORT 1-208-860-81 METAL CHIP
0 75
R3154 R3157 R3158 R3159 R3160
1-218-990-11 1-218-977-11 1-218-977-11 1-218-977-11 1-218-977-11
SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP
0 100K 100K 100K 100K
(TRV6/TRV6E) 5% 1/16W 5% 1/16W 5% 1/16W 5% 1/16W
R3171 R3172 R3173 R3174 R3175
1-216-864-11 1-216-864-11 1-216-864-11 1-216-855-11 1-218-961-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
0 0 0 680K 4.7K
5% 5% 5% 5% 5%
1/16W (TRV20E) (TRV6/TRV6E) 0.5% 1/16W (TRV20E) (TRV6/TRV6E) 0.5% 1/16W (TRV20E)
Ref. No.
SE-107
Part No.
Description
VC-240
VC-241 Remarks
A-7094-887-A VC-240(H) BOARD, COMPLETE (SERVICE) (TRV20/TRV20E) ************************************** (Ref.No.;10000Series) ************************************************************ A-7094-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) ************************************** A-7094-996-A VC-241(L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) ************************************** A-7094-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE) (TRV6E:AEP,UK) ************************************** A-7094-963-A VC-241(M-CE) BOARD, COMPLETE (SERVICE) (TRV11E:AEP,UK) ************************************** (Ref.No.;10000Series) ************************************************************
1/16W 1/16W 1/16W 1/16W 1/16W
R3176 1-218-953-11 RES-CHIP 1K 5% 1/16W R3177 1-216-864-11 METAL CHIP 0 5% 1/16W ************************************************************ A-7074-311-A SE-107 BOARD, COMPLETE ********************** (Ref.No.;4000Series) < PHOTO INTERRUPTER > PH081 8-749-011-97 PHOTO INTERUPTER GP1S93 PH082 8-749-011-97 PHOTO INTERUPTER GP1S93 ************************************************************
6-21
Electrical parts list of the VC-240/241 board are not shown. pages 6-23 to 6-44 are not shown.
Ref. No.
Part No.
Description
Remarks
MISCELLANEOUS ************* 15 18 62 103 104
1-694-493-11 1-677-561-11 1-418-979-11 1-960-425-11 1-960-426-11
1-418-877-21 TRANSFORMER UNIT, INVERTER
153 154 158 0 162
1-960-425-11 1-960-426-11 1-677-563-21 1-418-877-11
209 209 209 209 213 253 254 266 302 302 306 307 307 325 332
Part No.
0 ND901
1-517-869-41 TUBE, FLUORESCENT,COLD CATHODE (TRV11/TRV11E) 1-517-869-51 TUBE, FLUORESCENT,COLD CATHODE(TRV20E) 8-729-028-71 TRANSISTOR PN 166, SO (TAPE END) 8-729-028-71 TRANSISTOR PN 166, SO (TAPE TOP) 1-771-326-41 SWITCH, PUSH LEVER (1 KEY) (CC DOWN)
0 ND901 Q901 Q902 S903
TERMINAL BOARD, BATTERY FP-179 FLEXIBLE SWITCH BLOCK, CONTROL(CF30150) HARNESS (PC-118) HARNESS (PC-119)
0 112
Ref. No.
ACCESSORIES ************
(TRV6/TRV6E) HARNESS (PC-118) HARNESS (PC-119) FP-181 FLEXIBLE TRANSFORMER UNIT, INVERTER (TRV11/TRV11E/TRV20/TRV20E) 0
0 0
1-785-594-11 CONNECTOR (HOT SHOE), OUTER 1-758-155-21 FILTER BLOCK, OPTICAL (TRV6/TRV6E/TRV11/TRV11E) 1-758-353-11 FILTER BLOCK, OPTICAL (TRV20/TRV20E) 1-677-562-11 FP-180 FLEXIBLE 1-677-566-21 FP-219 FLEXIBLE, COMPLETE (TRV6/TRV6E/TRV11/TRV11E)
IC101 IC3000 IC3000 LCD901
A-7031-073-A A-7031-011-A A-7031-012-A 1-803-856-21
FP-228 FLEXIBLE FP-100 FLEXIBLE DIODE LA57A,SO (TAPE LED) ELEMENT, HOLE HW-105A-CDE-T (S REEL) ELEMENT, HOLE HW-105A-CDE-T (T REEL)
0
0
0 0
0 CCD BLOCK ASSY (TRV20/TRV20E) CCD BLOCK ASSY (TRV6/TRV11) CCD BLOCK ASSY (TRV6E/TRV11E) INDICATOR MODULE LIQUID CRYST (TRV11/TRV11E) LCD901 1-803-862-21 INDICATOR MODULE LIQUID CRYST (SERVICE) (TRV20) LCD901 LCD901 LCD903 LCD903 M901 M902 M903 MIC901 0 ND901 0 ND901
1-475-141-21 REMOTE COMMANDER (RMT-808) (TRV6/TRV6E:AUS,E,HK,JE,CN) 1-475-141-31 REMOTE COMMANDER (RMT-809) (TRV6E:AEP,UK) 1-475-599-11 ADAPTOR, AC (AC-L10) (TRV6:US,CND,HK,E,JE/TRV6E:AEP,UK,AUS,E,HK,JE/ TRV11:US,CND,HK,E,JE/TRV11E:AEP,UK,AUS,E,HK,JE/ TRV20:US,CND,HK,E,JE/TRV20E:AEP,UK,AUS,E,HK,JE) 1-475-599-71 ADAPTOR, AC (AC-L10) (TRV6:KR/TRV11:KR/TRV20:KR) 1-475-599-81 ADAPTOR, AC (AC-L10) (TRV6E:CN/TRV11E:CN/TRV20E:CN) 1-475-950-21 REMOTE COMMANDER (RMT-811) (TRV11/TRV11E:AUS,E,HK,JE,CN/TRV20/TRV20E) 1-475-950-31 REMOTE COMMANDER (RMT-812) (TRV11E:AEP,UK) 1-569-007-11 ADAPTOR, CONVERSION 2P (TRV6:JE/TRV6E:JE/TRV11:JE/TRV11E:JE/ TRV20:JE/TRV20E:JE) 1-569-008-21 ADAPTOR, CONVERSION 2P (TRV6:E,HK/TRV6E:E,HK/TRV11:E,HK/TRV11E:E,HK/ TRV20:E,HK/TRV20E:E,HK) 1-573-291-11 CONNECTOR, CONVERSION (21P) (TRV6E:AEP,UK/TRV11E:AEP,UK/TRV20E:AEP,UK)
1-677-565-11 FP-183 FLEXIBLE (TRV11/TRV11E/TRV20/TRV20E) 1-785-593-31 CONNECTOR, MEMORY STICK (TRV11/TRV11E/TRV20/TRV20E) 1-418-972-11 SWITCH BLOCK, CONTROL (PS30150) 8-848-737-01 DEVICE, LENS LSV-650B (TRV6/TRV6E/TRV11/TRV11E) 8-848-739-01 DEVICE, LENS LSV-690A (TRV20/TRV20E)
1-677-049-11 1-677-084-11 8-719-078-71 8-719-067-74 8-719-067-74
Remarks
SP901 1-529-590-11 SPEAKER (2.0CM) ************************************************************
1-418-973-31 SWITCH BLOCK, CONTROL (FK30150) (TRV11/TRV11E:AUS,E,HK,JE,CN/TRV20/TRV20E) 1-418-973-41 SWITCH BLOCK, CONTROL (FK30150) (TRV11E:AEP,UK) 1-418-973-51 SWITCH BLOCK, CONTROL (FK30150) (TRV6/TRV6E:AUS,E,HK,JE,CN) 1-418-973-61 SWITCH BLOCK, CONTROL (FK30150) (TRV6E:AEP,UK) 1-785-247-21 CONNECTOR, DC-IN
811 812 D901 H901 H902
Description
0
0
8-753-050-44 8-753-050-53 8-753-026-77 A-7094-871-A
ACX305AK-J (SERVICE)(TRV20E) ACX300CKA-1 (TRV6/TRV6E) LCX033AK-1 (TRV20/TRV20E) LCX032AK-1/5 COMPL (TRV6/TRV6E/TRV11/TRV11E) A-7048-940-A DRUM BLOCK ASSY (DEH-18A-R)(SERVICE)
8-835-685-01 A-7094-823-A 1-418-351-21 1-517-751-51
MOTOR, DC SCD18A/C-NP (INCLUDING BELT) MOTOR BLOCK ASSY, L MICROPHONE UNIT TUBE, FLUORESCENT,COLD CATHODE (TRV6/TRV6E) 1-517-869-31 TUBE, FLUORESCENT,COLD CATHODE (TRV20)
6-45
1-696-819-11 CORD,POWER (TRV6E:AUS/TRV11E:AUS/TRV20E:AUS) 1-765-080-11 CORD,CONNECTION (A/V)(1.5m) 1-769-608-11 CORD,POWER (TRV6:E/TRV6E:AEP,E/TRV11:E/TRV11E:AEP,E/ TRV20:E/TRV20E:AEP,E) 1-776-985-11 CORD,POWER (TRV6:KR/TRV11:KR/TRV20:KR) 1-782-476-11 CORD,POWER (TRV6E:CN/TRV11E:CN/TRV20E:CN) 1-783-374-11 CORD,POWER (TRV6:HK/TRV6E:UK,HK/TRV11:HK/TRV11E:UK,HK/ TRV20:HK/TRV20E:UK,HK) 1-790-073-11 CORD,POWER 2P (TRV6:JE/TRV6E:JE/TRV11:JE/TRV11E:JE/ TRV20:JE/TRV20E:JE) 1-790-107-22 CORD,POWER (TRV6:US,CND/TRV11:US,CND/TRV20:US,CND) 1-792-451-11 CABLE,RS 232C (TRV11/TRV11E/TRV20/TRV20E) 3-053-056-01 LID,BATTERY CASE (FOR RMT-811,812) (TRV11/TRV11E/TRV20/TRV20E)
Be sure to read “Precautions upon replacing CCD imager” on page 4-12,14 when changing the CCD imager. Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Ref. No.
Part No.
Description
Remarks
Ref. No.
3-057-401-01 HOOD,LENS (TRV20/TRV20E) 3-059-592-11 MANUAL, INSTRUCTION (ENGLISH) (TRV6:US,CND,E,HK,JE/TRV11:US,CND,E,HK,JE/ TRV20:US,CND,E,HK,JE) 3-059-592-21 MANUAL, INSTRUCTION (FRENCH) (TRV6:CND/TRV11:CND/TRV20:CND) 3-059-592-31 MANUAL, INSTRUCTION (SPANISH/PORTUGUESE) (TRV6:E,JE/TRV11:E,JE/TRV20:E,JE) 3-059-592-41 MANUAL, INSTRUCTION (TRADITIONAL CHINESE) (TRV6:E,HK/TRV11:E,HK/TRV20:E,HK) 3-059-592-51 MANUAL, INSTRUCTION (KOREAN) (TRV6:JE,KR/TRV11:JE,KR/TRV20:JE,KR) 3-059-592-61 MANUAL, INSTRUCTION (ARABIC) (TRV6:E/TRV11:E/TRV20:E) 3-059-593-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN) (TRV6E:AUS,E,HK,JE,CN/TRV11E:AUS,E,HK,JE,CN/ TRV20E:AUS,E,HK,JE,CN) 3-059-593-21 MANUAL, INSTRUCTION (FRENCH/GERMAN) (TRV6E:E,JE/TRV11E:E,JE/TRV20E:E,JE) 3-059-593-31 MANUAL, INSTRUCTION (ARABIC/PERSIAN) (TRV6E:E/TRV11E:E/TRV20E:E) 3-059-593-41 MANUAL, INSTRUCTION (SIMPLIFIED CHINESE) (TRV6E:E,JE,CN/TRV11E:E,JE,CN/TRV20E:E,JE,CN) 3-059-593-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE) (TRV6E:HK/TRV11E:HK/TRV20E:HK) 3-059-594-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN) (TRV6E:AEP,UK/TRV11E:AEP,UK/TRV20E:AEP,UK) 3-059-594-21 MANUAL, INSTRUCTION (FRENCH/GERMAN) (TRV6E:AEP/TRV11E:AEP/TRV20E:AEP) 3-059-594-31 MANUAL, INSTRUCTION (SPANISH/PORTUGUESE) (TRV6E:AEP/TRV11E:AEP/TRV20E:AEP) 3-059-594-41 MANUAL, INSTRUCTION (ITALIAN/DUTCH) (TRV6E:AEP/TRV11E:AEP/TRV20E:AEP) 3-060-457-11 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (ENGLISH) (TRV11:US,CND,E,HK,JE/TRV20:US,CND,E,HK,JE) 3-060-457-21 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (FRENCH) (TRV11:CND/TRV20:CND) 3-060-457-31 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (TRADITIONAL CHINESE) (TRV11:E,HK/TRV11E:HK/TRV20:E,HK/TRV20E:HK)
6-46E
Part No.
Description
Remarks
3-060-457-41 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (KOREAN) (TRV11:JE,KR/TRV20:JE,KR) 3-060-458-11 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (ENGLISH/RUSSIAN) (TRV11E/TRV20E) 3-060-458-21 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (FRENCH/GERMAN) (TRV11E:AEP,E,JE/TRV20E:AEP,E,JE) 3-060-458-31 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (ITALIAN/DUTCH) (TRV11E:AEP/TRV20E:AEP) 3-060-458-41 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (SPANISH/PORTUGUESE) (TRV11:E,JE/TRV11E:AEP/TRV20:E,JE/TRV20E:AEP) 3-060-458-61 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (ARABIC/SWEDISH) (TRV11:E/TRV11E:E/TRV20:E/TRV20E:E) 3-060-458-71 MANUAL, INSTRUCTION (PICTURE GEAR 4.1 LITE) (SIMPLIFIED CHINESE) (TRV11E:E,JE,CN/TRV20E:E,JE,CN) 3-060-476-01 DISK, SYSTEM (PICTURE GEAR 4.1 LITE) (TRV11/TRV11E/TRV20/TRV20E) 3-742-854-21 LID, BATTERY CASE (FOR RMT-808,809) (TRV6/TRV6E) 3-987-015-01 BELT(S), SHOULDER A-7033-740-A MEMORY STICK (TRV11/TRV11E/TRV20/TRV20E)
〈OPTICAL
AXIS FRAME〉
Take a copy of OPTICAL AXIS FRAME with a clear sheet for use.
✂
DCR-TRV6/TRV6E/TRV11/TRV11E
— 247 —
〈FOR
CAMERA COLOR REPRODUCTION ADJUSTMENT〉
For NTSC model
DCR-TRV6/TRV11 Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use.
✂ For PAL model
— 248 —
✂
DCR-TRV6E/TRV11E
〈FOR
CAMERA COLOR REPRODUCTION ADJUSTMENT〉
For NTSC model
DCR-TRV20 Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use.
✂ For PAL model
✂
DCR-TRV20E
— 249 —
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
9-929-818-31
Sony EMCS Co.
— 250 —
2003F1600-1 ©2003.6 Published by DI CS Strategy Div.
DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E
RMT-808/809/811/812 US Model Canadian Model Korea Model DCR-TRV6/TRV11/TRV20
SERVICE MANUAL
AEP Model UK Model Australian Model Chinese Model
Level 2
DCR-TRV6E/TRV11E/TRV20E
2000. 06
E Model Hong Kong Model Tourist Model DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E
CORRECTION-1 Correct your service manual as shown below. (00-002)
• Errors in SECTION 5. ADJUSTMENT and SECTION 6. REPAIR PARTS LIST are corrected as follows.
: Changed portion. Page
INCORRECT
CORRECT
SECTION 5. ADJUSTMENT
VC-241 board JK-188 board PD-123 board PD-124 board LB-64 board VC-241 board VC-241 board VC-241 board
(COMPLETE) (COMPLETE) (COMPLETE) *1 (COMPLETE) *2 (COMPLETE) IC801 (EEPROM) IC502 (EEPROM) IC1407 (Flash memory) *1
4. D Page Table
4. D Page Table
*1: TRV11/TRV11E/TRV20E model only *2: TRV6/TRV6E/TRV20 model only
*1: TRV11/TRV11E/TRV20 model only
Board replacement
5-12
(COMPLETE) (COMPLETE) (COMPLETE) *1 (COMPLETE) *2 (COMPLETE) IC801 (EEPROM) IC502 (EEPROM) IC1406 (EEPROM) *1
Board replacement
5-3
VC-241 board JK-188 board PD-123 board PD-124 board LB-64 board VC-241 board VC-241 board VC-241 board
SECTION 5. ADJUSTMENT
*2: TRV6/TRV6E/TRV20E model only
5-14
4. Modification of B Page Data (DCR-TRV11/TRV11E)
4. Modification of B Page Data (DCR-TRV11/TRV11E)
Processing after Completing Modification of B Page data:
Processing after Completing Modification of B Page data:
3)
3)
Select page: 5, address: 00, set data: 01, and press the PAUSE button. (The changed data are written in the EEPROM.)
Select page: 5, address: 00, set data: 01, and press the PAUSE button. (The changed data are written in the flash memory.)
: Changed portion. Page
: Deleted portion. INCORRECT
CORRECT
5. B Page Table Address
5-15
5. B Page Table Remark
Address
55 to 6F Fixed data-1 (Initialized data) 70 Fixed data-2 71 to FF Fixed data-1 (Initialized data)
Remark
55 to 5D Fixed data-1 (Initialized data) 5E Fixed data-2 5F 60 to 6F Fixed data-1 (Initialized data) 70 Fixed data-2 71 to FF Fixed data-1 (Initialized data)
Table. 5-1-6.
Table. 5-1-6. 4. V-COM Level Adjustment (PD-123 board)
4. V-COM Level Adjustment (PD-123 board)
Note: Perform “Bright Adjustment” and “Contrast Adjustment” before this adjustment.
Note: Perform “RGB AMP Adjustment” and “Contrast Adjustment” before this adjustment.
5. V-COM Adjustment (PD-123 board)
5. V-COM Adjustment (PD-123 board)
Note: Perform “Bright Adjustment” and “Contrast Adjustment” before this adjustment.
Note: Perform “RGB AMP Adjustment”, “Contrast Adjustment” and “V-COM Level Adjustment” before this adjustment.
2. PLL f0 & LPF f0 Adjustment (VC-240/241 board)
2. PLL f0 & LPF f0 Adjustment (VC-240/241 board)
Adjusting method: 5) Select page: 0, address: 01, and set data: 00.
Adjusting method: 5) Select page: 0, address: 01, and set data: 00.
5-38
5-51
5-53
Bit value of page: 3, address: 03 data bit 4 = 1 bit 5 = 1 bit 6 = 1 bit 3 = 1 bit 2 = 1
Error contents PLL f0, even channel is defective PLL f0, odd channel is defective LPF f0 is defective PLL f0, final adjustment is defective PLL f0, final adjustment time-out
Bit value of page: 3, address: 03 data bit 6 = 1 bit 3 = 1 bit 2 = 1
Error contents LPF f0 is defective PLL f0, final adjustment is defective PLL f0, final adjustment time-out
5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board)
5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board)
Adjusting method: 5) Select page: 0, address: 01, and set data: 00.
Adjusting method: 5) Select page: 0, address: 01, and set data: 00.
Bit value of page: 3, address: 03 bit 4 = 1 bit 5 = 1 bit 6 = 1 bit 3 = 1 bit 2 = 1
Error contents PLL f0, even channel is defective PLL f0, odd channel is defective LPF f0 is defective PLL f0 final adjustment is defective PLL f0 final adjustment time-out
—2—
Bit value of page: 3, address: 03 bit 6 = 1 bit 3 = 1 bit 2 = 1
Error contents LPF f0 is defective PLL f0 final adjustment is defective PLL f0 final adjustment time-out
Page
INCORRECT 2-2. MSW Code
Mechanism Position ← UNLOAD SOFF
BL
DS
BL
LE
BL
STOP
BL
FF
BL
RP
BL
RVS
0 0 1 1 = 3
1 1 1 1 = F 1 0 1 1 = B
1 1 1 1 = F 0 1 1 1 = 7
1 1 1 1 = F 0 1 0 1 = 5
1 1 1 1 = F 1 0 0 1 = 9
1 1 1 1 = F
BL
1 1 1 1 = F 1 1 0 1 = D
1 0 1 0 = A
USE
1 1 1 1 = F 1 1 0 0 = C
BL
1 1 1 1 = F 1 1 1 0 = E
EJECT
LOAD →
LS chassis movement range Pinch roller is pressed
Tension regulator ON
Releasing lock of cassette compartment
5-67
Position
Code
EJECT
A
BL
F
USE
E
SOFF DS LE
C D 9
STOP
5
FF
7
RP
B
RVS
3
NULL
0
Contents Position at which the cassette compartment lock is released, and position at the farthest unload side mechanically at which the mechanism can move no further in the UNLOAD direction. BLANK code, at the boundary between codes. The mechanism will not stop at this code during operations. (Excluding LOAD/UNLOAD) EJECT completion position. When the cassette is ejected, the mechanism will stop at this position. Cassette IN standby. The guide will start protruding out as the mechanism moves towards the LOAD position. Code during loading. Code outputs while the LS chassis is moving. LS operations and guide loading are performed here. Current limiter is turned off. Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the brake is imposed on both reels. FF position. The tension regulator is half on. This position is not used except for the FF mode. PB, REC, CUE, Pause, FX2, FWD-SLOW positions. When the pinch roller is pressed, and the tension regulator is ON, the mechanism is operating at this position in modes in which normal images are shown. Reverse running position. REW, REV, RX1, RX2, and RVS-SLOW are performed at this position. Code not existing in the MD. When errors occur when the loading motor is not driving, this code is memorized.
—3—
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
: Changed portion. Page
CORRECT 2-2. MSW Code
Mechanical Position ← UNLOAD BL
EJ
LOAD → BL
ULE
SR
BL
GL
BL
STOP
BL
R/P
1 1 0 = 6
1 1 1 = 7 0 1 0 = 2
1 1 1 = 7 0 1 1 = 3
1 1 1 = 7 0 0 1 = 1
1 1 1 = 7 1 0 1 = 5
1 1 1 = 7
1 0 0 = 4
← C (MSB) ←B ← A (LSB)
LS chassis movement section
5-67
Lock released Cassette compartment
Position
Code
EJ
4
BL
7
ULE
5
SR GL
1 3
STOP
2
R/P
6
NULL
0
Pinch roller pressing
Contents Position at which the cassette component lock is released, at the farthest unload side mechanically at which the mechanism can move no further in the UNLOAD direction. BLANK code, at the boundary between codes. EJECT completion position. when the cassette is ejected, the mechanism will stop at this position. Cassette IN standby. The guide will start protruding out as the mechanism moves towards the LOAD position. Position at which it is possible to release the S ratchet. Guide loading are performed here. Stop position in the loading state. The pinch roller separates, the tension regulator returns, and the brake is imposed on both reels. PB, REC, CUE, REVIEW, PAUSE positions. When pinch roller is pressed, and the tension regulator is ON, the mechanism is operating at this position in modes in which normal images are shown. Code not existing in the MD. Default value.
INCORRECT
CORRECT
SECTION 6. REPAIR PARTS LIST Ref. No. 210
6-5 210 210
6-21
9-929-818-91
Part No.
Description
SECTION 6. REPAIR PARTS LIST Remarks
Ref. No.
A-7074-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) A-7074-996-A VC-241 (L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) A-7074-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE)(TRV6E:AEP,UK)
210 210 210
A-7074-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) *********************************** A-7074-996-A VC-241(L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) *********************************** A-7074-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE)(TRV6E:AEP,UK) ***********************************
Sony EMCS Co.
—4—
Part No.
Description
Remarks
A-7094-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) A-7094-996-A VC-241 (L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) A-7094-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE)(TRV6E:AEP,UK)
A-7094-995-A VC-241 (M) BOARD, COMPLETE (SERVICE) (TRV11/TRV11E:AUS,E,HK,JE,CN) *********************************** A-7094-996-A VC-241(L) BOARD, COMPLETE (SERVICE) (TRV6/TRV6E:AUS,E,HK,JE,CN) *********************************** A-7094-997-A VC-241 (L-CE) BOARD, COMPLETE (SERVICE)(TRV6E:AEP,UK) ***********************************
2001K1600-1 ©2001.11 Published by DI Customer Center
DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E
RMT-808/809/811/812 US Model Canadian Model Korea Model DCR-TRV6/TRV11/TRV20
SERVICE MANUAL
AEP Model UK Model Australian Model Chinese Model
Level 2
DCR-TRV6E/TRV11E/TRV20E
Ver 1.3 2003. 06
SUPPLEMENT-1
E Model Hong Kong Model Tourist Model
File this supplement with the Service Manual. (PV03-001)
DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E
• Change of IC (Version up)
SECTION 5 ADJUSTMENTS 1. Before starting adjustment : Supplied portion.
IC102 (REC/PB AMP) IC1901 (IR transmitter) IC802 (Camera controll) *3
Adjustment Section
VC-241 board VC-241 board
Adjustment Section
NEW
VC-241 board VC-241 board VC-241 board
5-2
IC102 (REC/PB AMP) IC1901 (IR transmitter)
1-1. Adjusting items when replacing main parts and boards. Page FORMER
Supplied contents *3: When IC802 of the VC-241 board is going to be exchanged, the data on page : E, address : 53 and the data 6F must be modified. Be sure to enter the following data without fail. 5-3
Input method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: E, address: 53, set data: 01, and press the PAUSE button. 3) Select page: E, address: 6F, set data: 82, and press the PAUSE button. 4) Select page: 0, address: 01, and set data: 00.
9-929-818-82
Sony EMCS Co.
2003F1600-1 ©2003.6 Published by DI CS Strategy Div.
Reverse
992981834.pdf
Revision History History
Contents
S.M. Rev. issued —
Ver.
Date
1.0
2000.03
Official Release
1.1
2000.06
Correction-1
Error correction S.M. correction: Page 5-3, 5-12, 5-14, 5-15, 5-38, 5-51, 5-53, 5-67, 6-5, 6-21
Yes
1.2
2001.11 2003.06
Correction of Self-diagnosis code S.M. correction: Page 10 Change of IC (Version up)
Yes
1.3
Correction-2 (PV01-037) Supplement-1
—
No