SERVICE MANUAL VIDEO CASSETTE RECORDER
HR-J282EU, HR-J283EU, HR-J285EU, HR-J290EU, HR-J293EU, HR-J295EK, HR-J295MS, HR-J582EU, HR-J583EU, HR-J585EU, HR-J590EU, HR-J593EU, HR-J595EK, HR-J595MS SPECIFICATIONS (The specifications shown pertain specifically to the model HR-J290EU, J293EU, J590EU and J593EU.) GENERAL Power Power consumption Power on Standby mode Video Head system HR-J590/J593/ J599EU HR-J290/J293EU Tape speed (SP) (LP)*
AUDIO : 200 V – 240 V
, 50 Hz/60 Hz
: Approx. 12 W : 3.0 W : DA4 (Double Azimuth) head helical scan system : Rotary two-head helical scan system : 23.39 mm/sec : 11.69 mm/sec
* HR-J590/J593/J599EU only
Tape format
: Tape width 1/2" (12.7 mm high density VHS tape)
Maximum recording time (SP) : 240 min. with E-240 video cassette (LP)* : 480 min. with E-240 video cassette * HR-J590/J593/J599EU only
Rewind time Dimensions (W x H x D) Weight Operating temperature Operating humidity Timer
: : : : : :
Approx. 180 sec. with E-180 cassette 360 mm x 94.5 mm x 270 mm 4.0 kg 5°C to 35°C Less than 80 % 24 hours display type
VIDEO Signal system
Recording Format RF reception RF OUT RF modulator Input level Output level Signal-to-noise ratio
: PAL-type colour signal and CCIR monochrome signal, 625 lines 50 fields : PAL/MESECAM : PAL (B/G)/SECAM (B/G) : PAL G : UHF channels 22 – 68 (Adjustable) : VIDEO IN (SCART type) 1.0 Vp-p, 75 ohm, unbalanced : VIDEO OUT (SCART type) 1.0 Vp-p, 75 ohm, unbalanced : More than 43 dBm
Input level Output level HR-J590/J593/ J599EU HR-J290/J293EU
: AUDIO IN (SCART type) –6.0 dBm, more than 10 kΩ : AUDIO OUT (SCART, RCA type) –6.0 dBm, less than 1 kΩ : AUDIO OUT (SCART type) –6.0 dBm, less than 1 kΩ
Audio track HR-J590/J593/ : Mono track and Hi-Fi track J599EU HR-J290/J293EU : Mono track Audio frequency response Normal audio : 100 Hz to 10,000 Hz (–6/+3 dBm) Hi-Fi audio* : 20 Hz to 20,000 Hz (–3/+3 dBm) * HR-J590/J593/J599EU only
Audio signal to noise ratio [HR-J590/J593/J599EU only] Hi-Fi audio : More than 70 dB (JIS A filter) Audio dynamic range [HR-J590/J593/J599EU only] Hi-Fi audio : More than 85 dB (JIS A filter)
ACCESSORIES Provided accessories
: RF cable, Infrared remote control unit, “R3” battery x 2
Specifications shown are for SP mode unless specified otherwise. E. & O.E. Design and specifications subject to change without notice.
This service manual is printed on 100% recycled paper. COPYRIGHT © 2002 VICTOR COMPANY OF JAPAN, LTD
V15
No.82915 June 2002
TABLE OF CONTENTS BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . .3-21
SECTION 1 SUMMARY
1. Power Block Diagram . . . . . . . . . . . . . . . . . . . .3-21 2. Tuner/IF, NICAM & A2 Block Diagram . . . . . . . .3-23 3. VPS Block Diagram . . . . . . . . . . . . . . . . . . . . . .3-24
KEY TO ABBREVIATIONS . . . . . . . . . . . . . . . . 1-1 IMPORTANT SAFETY PRECAUTIONS . . . . . . . . . . 1-2 PROPOSAL FOR APPLYING SHORT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4 SERVICE NOTICE ON REPLACING EEPROM . .1-5 SERVICE INFORMATION FOR EEPROM IC SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . 1-7
4. Y/C Block Diagram . . . . . . . . . . . . . . . . . . . . . .3-25 5. Hi-Fi Block Diagram . . . . . . . . . . . . . . . . . . . . .3-26 6. System Block Diagram . . . . . . . . . . . . . . . . . . .3-27
CIRCUIT DIAGRAMS . . . . . . . . . . . . . . . . . . . .3-29 1. Power Circuit Diagram . . . . . . . . . . . . . . . . . . . .3-29 2. Tuner, NICAM/A2 Circuit Diagram . . . . . . . . . . .3-31 3. A/V, SECAM, VPS Circuit Diagram . . . . . . . . . .3-33 4. System Circuit Diagram . . . . . . . . . . . . . . . . . . .3-35 5. Hi-Fi, SCART Circuit Diagram . . . . . . . . . . . . . .3-39 • CIRCUIT VOLTAGE CHART . . . . . . . . . . . . . . . .3-41
SECTION 2 CABINET & MAIN CHASSIS
PRINTED CIRCUIT BOARD DIAGRAMS . . . . .3-45 1. MAIN P.C.Board . . . . . . . . . . . . . . . . . . . . . . . .3-45
SERVICE METHOD . . . . . . . . . . . . . . . . . . . . . 2-1 Electrical Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
EXPLODED VIEWS . . . . . . . . . . . . . . . . . . . . . . 2-2 1. Cabinet & Main Frame Section . . . . . . . . . . . . . 2-2 2. Packing & Accessory Section
SECTION 4 MECHANISM
. . . . . . . . . . . . . . 2-3 NOTE) The table of contents for this section is edited NOTE) separately.
SECTION 3 ELECTRICAL ELECTRICAL ADJUSTMENT POINTS ARRANGEMENT . . . . . . . . . . . . . . . . . . . . . . . .3-1 ELECTRICAL ADJUSTMENT PROCEDURES . . 3-2 1. Servo Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
ELECTRICAL TROUBLESHOOTING GUIDE . . . 3-4 1. Power Circuit(SMPS) . . . . . . . . . . . . . . . . . . . . . 3-4 2. Servo Circuit
. . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
3. System & Front Panel Circuit . . . . . . . . . . . . . . .3-10 4. Y/C Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12 5. Tuner/IF Circuit . . . . . . . . . . . . . . . . . . . . . . . . .3-16 6. Hi-Fi Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19
SECTION 5 REPLACEMENT PARTS LIST 5-1 EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . . .5-1 5-2 REPLACEMENT PARTS LIST. . . . . . . . . . . . . . . . .5-4
SECTION1 SUMMARY KEY TO ABBREVIATIONS A
B
C
AC ACC ACSS ADJ A/E AFC AFT AGC A.H.SW ALC AM AMP ANT APC ASS’Y AUX B BGP BPF BS BW or B/W C CAN CAP CAP.BRK CAP.RVS CATV CBA CCD C.CTL CFG CHROMA CNR COMB COMP
D
E
F
G H I
L
CONV C.ROT SW CS C.SYNC CTL DIV CUR CYL D D.ADJ DC D.CTL DEMOD DET DEV DHP DIGITRON DL DOC DUB D.V SYNC E EE EMPH ENA ENV EP EQ EXP F FB FBC FE FG FL FM F/R FS FSC F/V GEN H IC IF INS L LD LD VTG CTL LECHA L.M LP
:Alternating Current :Automatic Color Control :Automatic Channel Setting System :Adjust :Audio Erase :Automatic Frequency Control :Automatic Fine Tuning :Automatic Gain Control :Audio Head Switch :Automatic Level Control :Amplitude Modulation :Amplifier :Antenna :Automatic Phase Control :Assembly :Auxiliary :Base :Burst Gate Pulse :Bandpass Filter :Brodcasting Satellite :Black and White :Capacitor, Chroma, Collector :Cancel :Capstan :Capstan Brake :Capstan Reverse :Cable Television :Circuit Board Assembly :Charge Coupled Device :Chro Control, Capstan Control :Capstan Frequency Generator :Chrominance :Chroma Noise Redution :Combination Comb Filter :Comparator Composite Compensation :Converter :Color Rotary Switch :Chip Selcet :Composite Synchronization :Control Divide :Current :Cylinder :Drum, Digital, Diode, Drain :Drum Adjust :Direct Current :Drum Control :Demodulator :Detector :Deviation :Double High Pass :Digital Display Tube :Delay line :Drop Out Compensator :Dubbing :Dummy Vertical Synchronization :Emitter :Electric to Eletric :Emphasis :Enable :Envelope :Extended Play :Equalizer :Expander :Fuse :Feed Back :Feed Back Clamp :Full Erase :Frequency Generator :Filter :Frequency Modulation :Front/Rear :Frequency Synthesizer :Subcarrier Frequency :Frequency Voltage :Generator :High, Horizontal :Integrated Circuit :Intermediate Frequency :Insert :Low, Left, Coil :LED :Loading Voltage Control :Letter Character :Level Meter :Long Play
M
N O P
Q
R
S
T
U V
W
X Y Z
1-1
LPF MAX MD MECHA.CTL MIC MIN MIX M.M. MMV MOD MODEM MPX NR
:Low Pass Filter :Maximum :Modulator :Mechanism Control :Microphone :Minimum :Mixer, Mixing :Monostable, Multivibrator :Mono Multi Vibrator :Modulation, Modulator :Modulator-Demodulator :Multiplex :Noise Reduction
OSC OSD PB PCB P.CTL PRE-AMP P.F PG PLL PREM.DET P.P PS PWM PWR CTL Q QH QSR QTR QV R RE(or RC) REC REC S ‘H’ REF REG REMOCON RF R/P RTC S S.ACCEL SAOP SC S.DET SH SHARP SIF SLD S/N SP ST SUB SW or S/W SYNC SYSCON T TP TR TRK TRANS TU UHF UNREG V VA VCO VGC VHF V.H.SW VISS VPS VR V-SYNC VTG VV VXO W WHT W/O X-TAL Y/C YNR ZD
:Oscillator :On Screen Display :Playback :Printed Circuit Board :Power Control :Preamplifier :Power Failure :Pulse Generator :Phase Locked Loop :Premire Detect :Peak-to-Peak :Phase Shift :Pulse Width Modulation :Power Control :Transistor :Quasi Horizontal :Quick Setting Record :Quick Timer Record :Quasi Vertical :Resistor, Right :Remocon, Receiver :Recording :Record Start ‘Hight’ :Reference :Regulated, Regulator :Remote Control(unit) :Radio Frequency :Record/Playback :Reel Time Counter :Serial :Slow Accel :Second Audio Program :Scart, Simulcast :Secam Detect :Shift :Sharpness :Sound Intermediate Frequency :Side Locking :Signal to Noise Ratio :Standard Play :Stereo :Subtract, Subcarrier :Switch :Synchronization :System Control :Coil :Test Point :Transistor :Tracking :Transformer :Tuner, Take-up :Ultra High Frequency :Unregulated :Volt, Vertical :Always Voltage :Voltage Controlled Oscillator :Voltage Gain Control :Very High Frequency :Video Head Switch :VHS Index Search :Video Program System :Variable Resistor or Volume :Vertical Synchronization :Voltage :Voltage to Voltage :Voltage X-tal Oscillator :Watt :White :With out :Crystal :Luminance/Chrominance :Luminance Noise Reduction :Zener Diode
Important Safety Precautions Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
v Precautions
during Servicing 12. Crimp type wire connector In such cases as when replacing the power transformer in sets where the connections between the power cord and power transformer primary lead wires are performed using crimp type connectors, if replacing the connectors is unavoidable, in order to prevent safety hazards, perform carefully and precisely according to the following steps.
1. Locations requiring special caution are denoted by labels and inscriptions on the cabinet, chassis and certain parts of the product. When performing service, be sure to read and comply with these and other cautionary notices appearing in the operation and service manuals. 2. Parts identified by the symbol and shaded ( ) parts are critical for safety. Replace only with specified part numbers. Note: Parts in this category also include those specified to comply with X-ray emission standards for products using cathode ray tubes and those specified for compliance with various regulations regarding spurious radiation emission.
1) Connector part number : E03830-001 2) Required tool : Connector crimping tool of the proper type which will not damage insulated parts. 3) Replacement procedure (1) Remove the old connector by cutting the wires at a point close to the connector. Important : Do not reuse a connector (discard it).
3. Fuse replacement caution notice. Caution for continued protection against fire hazard. Replace only with same type and rated fuse(s) as specified. 4. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads
cut close to connector
Fig.3
5. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 3) Spacers 5) Barrier 2) PVC tubing 4) Insulation sheets for transistors
(2) Strip about 15 mm of the insulation from the ends of the wires. If the wires are stranded, twist the strands to avoid frayed conductors. 15 mm
6. When replacing AC primary side components (transformers, power cords, noise blocking capacitors, etc.) wrap ends of wires securely about the terminals before soldering. Fig.4 (3) Align the lengths of the wires to be connected. Insert the wires fully into the connector. Fig.1
Metal sleeve
7. Observe that wires do not contact heat producing parts (heatsinks, oxide metal film resistors, fusible resistors, etc.)
Connector
8. Check that replaced wires do not contact sharp edged or pointed parts.
Fig.5
9. When a power cord has been replaced, check that 10-15 kg of force in any direction will not loosen it.
(4) As shown in Fig.6, use the crimping tool to crimp the metal sleeve at the center position. Be sure to crimp fully to the complete closure of the tool.
Power cord Crimping tool
1.2 5 2.0 5.5
Fig.6
Fig.2
(5) Check the four points noted in Fig.7.
10. Also check areas surrounding repaired locations. 11. Products using cathode ray tubes (CRTs) In regard to such products, the cathode ray tubes themselves, the high voltage circuits, and related circuits are specified for compliance with recognized codes pertaining to X-ray emission. Consequently, when servicing these products, replace the cathode ray tubes and other parts with only the specified parts. Under no circumstances attempt to modify these circuits. Unauthorized modification can increase the high voltage value and cause X-ray emission from the cathode ray tube.
Not easily pulled free
Crimped at approx. center of metal sleeve
Conductors extended Wire insulation recessed more than 4 mm Fig.7
1
S40888-01
v Safety
Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1. Insulation resistance test Confirm the specified insulation resistance or greater between power cord plug prongs and externally exposed parts of the set (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.). See table 1 below. 2. Dielectric strength test Confirm specified dielectric strength or greater between power cord plug prongs and exposed accessible parts of the set (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.). See table 1 below. 3. Clearance distance When replacing primary circuit components, confirm specified clearance distance (d), (d’) between soldered terminals, and between terminals and surrounding metallic parts. See table 1 below. Chassis
d d' Power cord, primary wire
Fig. 8 4. Leakage current test Confirm specified or lower leakage current between earth ground/power cord plug prongs and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.). Measuring Method : (Power ON) Insert load Z between earth ground/power cord plug prongs and externally exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See figure 9 and following table 2.
a
Externally exposed accessible part
b c
Z V
Fig. 9 5. Grounding (Class 1 model only) Confirm specified or lower grounding impedance between earth pin in AC inlet and externally exposed accessible parts (Video in, Video out, Audio in, Audio out or Fixing screw etc.). Measuring Method: Connect milli ohm meter between earth pin in AC inlet and exposed accessible parts. See figure 10 and grounding specifications.
Exposed accessible part
AC inlet
Grounding Specifications Region
Earth pin
Grounding Impedance (Z)
USA & Canada
Z ≤ 0.1 ohm
Europe & Australia
Z ≤ 0.5 ohm
Milli ohm meter Fig. 10
AC Line Voltage 100 V 100 to 240 V 110 to 130 V 110 to 130 V 200 to 240 V
Region
Insulation Resistance (R) R ≤ 1 MΩ/500 V DC
Japan USA & Canada Europe & Australia
1 MΩ ≥ R ≥ 12 MΩ/500 V DC R ≤ 10 MΩ/500 V DC
Dielectric Strength AC 1 kV 1 minute AC 1.5 kV 1 miute AC 1 kV 1 minute AC 3 kV 1 minute (Class 2) AC 1.5 kV 1 minute (Class 1)
Clearance Distance (d), (d') d, d' ≤ 3 mm d, d' ≤ 4 mm d, d' ≤ 3.2 mm d ≤ 4 mm d' ≤ 8 mm (Power cord) d' ≤ 6 mm (Primary wire)
Table 1 Specifications for each region
AC Line Voltage
Region
100 V
Japan
110 to 130 V
USA & Canada
110 to 130 V 220 to 240 V
Load Z
Leakage Current (i)
a, b, c
i ≤ 1 mA rms
Exposed accessible parts
i ≤ 0.5 mA rms
Exposed accessible parts
2 kΩ
i ≤ 0.7 mA peak i ≤ 2 mA dc
Antenna earth terminals
50 kΩ
i ≤ 0.7 mA peak i ≤ 2 mA dc
Other terminals
1 kΩ
Europe & Australia
0.15 µF 1.5 kΩ
Table 2 Leakage current specifications for each region Note: These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.
2
S40888-01
PROPOSAL FOR APPLYING SHORT PROTECTION • The Contents of Examination As all the IC that is applied to VCR is controlled by IIC, mutual communication, if Vcc of IC is short or open with detecting ‘Acknowledge’ data of the specific IC according to each power(5V, 5VT) µ-COM gets unable to detect ‘ACK’ data. µ-COM regards this case as abnormal one and if it can’t detect ‘ACK’ data for a certain time(3.5 sec) the signal of ‘Power Control’ and ‘Timer Control’ are switched to ‘Low’. As a result POWER Switching TR is kept from generating heat and fire.
Conception BLOCK Diagram
TIMER CONTROL
5VT SW
SLAVE with 5V IIC BUS
MASTER
SLAVE with 5V POWER CONTROL
5VT SW
• POWER for each IC 5.2V
5.2VT Modulator 5.3VA
5.3VA
Hi-Fi IC
AVCP IC TUNER
NICAM IC SECAM IC Timer Control
Power Control
• IC to detect ‘ACK’ data is selected as below because IC is different in accordance to region and option
S/ Series P/Y/I Series
5V POWER 5VT POWER 5V POWER 5VT POWER
SECAM IC AVCP IC Modulator AVCP IC
*Short protection off mode : DJ01 Diode in
1-4
SERVICE NOTICE ON REPLACING EEPROM In case that defective EEPROM of PAL models is replaced, to operate these sets from the initial state MP KEY must be repaired as well before delivering to the customer. If MP KEY isn’t repaired the setting of RF OUT channel or LANGUAGE might be different from that for custormer’s country. •MP KEY : In case of PAL VCR if holding the REC button on the front panel and the CLEAR button on the remote control handset for 5 ~ 7 seconds with power being switch all and no tapes, OK is displayed at FLD for FLD models and LED becomes on for LED CLOCK models. This is the state that initializing EEPROM is finished. (In case of PAL VCP if holding the REC button on the front panel and the MENU button on the remote control handset for 5 ~ 7 seconds with power being off and no tapes, All the LED DOTs become on. This is the state that initializing EEPROM is finished.) •MP KEY's function : MP KEY sets EEPROM's data up to the initial state.
• FLD MODEL: MP KEY “OK”
OK REC VCR
TIMER
• LED CLOCK MODEL: MP KEY Switch all on a Light
AM
• LED DOT MODEL: MP KEY Switch all on a Light
1-5
SERVICE INFORMATION FOR EEPROM IC SETTING MODEL HR-J283EU
EEPROM option code No. setting
HEX 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
BINARY 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
HR-J582EU
HR-J583EU
HEX 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
BINARY 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
# Remote control Key action • OK : Now option data write to EEPROM • MENU : Menu exit • EDIT : ▲▼ (Option data change from 0~F Hexadecimal) • MOVE : ▲▼ (Cursor move for option data setting) ▲
NAME 02 C0 C0 B1 30 48 HR-J290EU E2 HR-J293EU C1 C8 B1 30 48 HR-J585EU 0C C0 C0 B1 30 48 HR-J590EU/ EC J593EU C1 C8 B1 30 48 HR-J595EK 2C C0 C8 B4 00 43 HR-J595MS 6C C0 48 B0 62 40 HR-J295MS 62 C0 48 B0 62 40 HR-J295EK 02 C0 C8 B4 00 43 HR-J282EU 02 C0 C0 B7 00 50
▲
MODEL HR-J285EU
NAME 02 C0 C8 B7 00 50 0C C0 C0 B7 00 50 0C C0 C8 B7 00 50
EEPROM option code No. setting procedure 1. Power Cord plug-in and Power SW on, then “EEPROM option data setting” screen to the left will be displayed. # If not, press the “Child lock” key on the Remote controller to switch with “CANAL” because the VCR set has “CANAL IC” inside. # If your VCR set has “NTSC Line Record”, switch the VCR set to “AV” mode after inputting the Line Video signal. If not, the Blue back screen may be shown in to screen. 2. Refer to option data in the next page and input the value to the “HEX” field using “EDIT” key only, and then press the “OK” key on the Remote controller. 3. Check the basic operation (Tuner/PB/CUE/REV/AV/REC mode...) 4. Initialize the EEPROM IC pressing the “REC” key on the Front Panel and “CLEAR” key on the Remote controller at the same time.
1-6
SPECIFICATIONS General Power Power consumption Video Head system
Tape speed Tape format Maximum recording time Rewind time Dimensions (W X H X D) Weight Operating temperature Operating humidity Timer Video Television system Recording format
Input level Output level Signal to noise ratio Audio Input level Output level
Audio track Audio signal to noise ratio Audio dynamic range
: 200~240V, 50Hz : Approx. 12 watts(Energy Saving mode : 3 watts) : Rotary 2heads, helical scanning system (2HD Model) Double azimuth 4 heads, helical scanning system (4HD MONO, 4HD Hi-Fi Model) : 23.39 mm/sec (SP mode)11.69 mm/sec(LP mode) : Tape width 1/2” (12.7 mm high density VHS tape) : 4 hours in SP mode/8 hours in LP mode (with E-240 tape) : Approx. 150 sec. (with E-180 tape) : 360 x 94.5 x 270 mm : 9.0 lbs. (4.0 kg) : 41°F-95°F (5°C-35°C) : Less than 80% : 24 hours display type
: CCIR standard (625 lines, 50 fields) PAL colour signal : PAL B/G (HR-J282EU/J283EU/J582EU/J583EU/J285EU/ J290EU/293EU/J585EU/J590EU/J593EU) PAL N (HR-J295EK/J595EK) PAL SECAM-L (HR-J295MS/J595MS) : VIDEO IN (SCART, RCA type) 1.0 Vp-p, 75 ohm, unbalanced : VIDEO OUT (SCART type) 1.0 Vp-p, 75 ohm, unbalanced : More than 43 dBm
: AUDIO IN (SCART type) Scart type : -6.0dBm, more than 10kΩ : AUDIO OUT (SCART, RCA type) Scart type : -6.0dBm, less than 1kΩ RCA type : -6.0 dBm, less than 1kΩ Mono track & Hi-Fi track : Normal : More than 70 dBm(JIS A filter) : Hi-Fi audio : More than 85 dBm(JIS A filter)
• Design and specifications are subject to change without notice. :Hi-Fi Model only
1-7
SECTION 2 CABINET & MAIN CHASSIS SERVICE METHOD Electrical Part (1) Re-assembly Flow for service like Fig. 2-1
Timer C.B.A
Main C.B.A
Housing & Deck Assembly
(2) To check and replace Electrical parts 2 Re-assemble the unit according to No.1) Re-assembly Flow. 3 Place the unit like Fig. 2-1 4 Check and replace Electrical parts. NOTE : 1 Insert Video Cassette Tape inversely like Fig. 2-1 to check and replace defective parts. 2 In disassembling and reassembling, be careful not to damaged CST switch. (Positioned Upside Down) Main C.B.A
Cassette Tape (Upside Down) Housing & Deck Ass'y
Timer C.B.A
Fig.2-1
2-1
EXPLODED VIEWS 1. Cabinet and Main Frame Section 452
NOTE) Refer to “SECTION 5 REPLACEMENT PARTS LIST” in order to look for the part number of each part. OPTIONAL PARTS
A46 LED502(LED501)
323
TU70 1(TU NER )
1SCART
452
452
2SCART
462
320
300
5
250
462
330
275
4
464
A43
260
A49
452
3
280
277
283
A42
A00
284
457
2
281
1
A
B
C 2-2
D
2.Packing Accessory Section NOTE) Refer to “SECTION REPLACEMENT PARTS LIST NOTE) in order to look for the part number of each part.
OPTIONAL PARTS 806
811 810 812
CABLE SET ASS'Y (Optional parts)
PLUG ASS'Y 1WAY (Optional parts)
PLUG ASS'Y 2WAY (Optional parts)
821
801 808
BATTERY
803
PACKING (LF)
SCART CABLE
INSTRUCTION MANUAL
804
BAG. SOFR SHEET
803
802
PACKING (RF)
BOX CARTON 900
2-3
REMOCON
SECTION 3 ELECTRICAL ELECTRICAL ADJUSTMENT POINTS ARRANGEMENT : Measurement point : Adjustment point
SCART JACK Speak-ez
S M P S
SW/IC T U N E R
Hi-Fi
VPS SECAM
A/V
AVCP
C+
W501 W502
Micom
H.S/W
SYSTEM EEPROM
NICAM
CLK IC E2PROM
DISPLAY(DOT,CLK)
(COMPONENT SIDE)
3-1
ELECTRICAL ADJUSTMENT PROCEDURES 1. Servo Adjustment 1) PG Adjustment • Test Equipment a) OSCILLOSCOPE b) PAL TEST TAPE (VHS SP) c) JIG REMOCON (AUTO PG SETTING)
• Adjustment And Specification MODE
MEASUREMENT POINT
PLAY
V.Out H/SW(W501, W502)
ADJUSTMENT POINT
SPECIFICATION 6.5 ± 0.5H
• Adjustment Procedure a) Insert the PAL SP Test Tape and play. Note - Adjust the distance of X, pressing the Tracking(+) or Tracking(-) when the “ATR(OSD on monitor)” is blink after PAL SP test Tape is inserted. b) Press the Auto PG KEY on JIG Remocon(1’st) or Press “Play” key on set and “0” key on Remocon.(Then check the light 4 Dot LED on CLK/LED - TRK is a Initial) c) Press the Auto PG Key on JIG Remocon again (2’nd) or press “Play” key on set and “0” key on Remocon again.(Then check the blink 4 Dot LED - At regular 0.25sec internal, Then check blink “PG waveform” on oscilloscope(MONO Model)).
• Check the PG a) Connect the CH1 of the oscilloscope to the H/SW and CD2 to the Video out for the VCR. b) Trigger the mixed Video Signal of CH2 to the CH1 H/SW(W501, W502), and then check the distance (time difference), which is from the selected A(B) Head point of the H/SW(W501, W502) signal to the starting point of the vertical synchronized signal, to 6.5H ± 0.5H (416µs, 1H=64.0µs).
• CONNECTION
V.Out
OSCILLOSCOPE CH1 CH2 H/SW(W501,W502)
H/SW V.out (W501, W502)
3-2
ELECTRICAL ADJUSTMENT PROCEDURES • WAVEFORM
H/SW 6.5H(416us)
Composite VIDEO
• Attension and Reference a) The PG checking must do when RF Level is Maximum and SERVO system is Locking (MTR MODE) b) V.H/SW Level is 2Vpp.
3-3
ELECTRICAL TROUBLESHOOTING GUIDE 1. Power Circuit(SMPS) (1) No 5.3VA. No 5.3VA. YES Is the F101 normal?
NO
Replace the F101 (Use the same Fuse).
YES Is the BD101 normal?
NO
Replace the BD101.
YES Is the R101 normal?
NO
Replace the R101.
YES Does the oscillation waveform appear at the IC101 Pin 7?
NO
Is Vcc(about 13~15V) permittable at the IC101 Pin 3? NO
YES
Check or Replace the D103.
Is there DC voltage at the IC101 Pin 4?
NO
Replace the IC102.
YES Is there about 2.5V at the IC103 Vref ?
NO
Replace the IC103.
YES Is the D106 normal?
NO
YES Check the Main PCB 5.3VA Line short?
3-4
Replace the D106.
7. Power Circuit(SMPS) (2) No 12VA.(Capstan) No 12VA. YES Does 5.3VA work normally?
NO
Check whether 5.3VA is out of order.
YES Is the D109 normal?
NO
Replace the D109.
YES Check 12VA Line of the Main PCB short.
(3) No 12VA (CANAL, Buffer)
No 12VA. YES Is Vcc(about 13VA) put into the Q155(E)?
NO
YES Is Voltage(about 12V) put into the Q155(C)? YES Check or Replace the Q155.
3-5
Replace the Peripheral Circuitry of D160.
7. Power Circuit(SMPS) (4) No 5VT(5V) No 5VT.(5V) YES Is 5.3VA put into the Q152(Q151) collector? YES Is the Q163(Q162) Base “H”?
NO
Check the µ-com Control.
YES Is about 4.7V put into the Q152(Q151) Base?
NO
YES Check or Replace the Q152(Q151).
3-6
Check the Q163(Q162) whether it works normally.
2. Servo Circuit A.
Unstable Video in PB Mode.
Does the on screen noise level change periodically? YES
Do CTL pulses appear at IC501 pin 8? YES
NO
Does the CFG divide waveform appear at IC501 pin 9?
Is the height of the CTL Head adjusted correctly? NO
YES
Do the CTL pulses move when TRK is operated? YES
Adjust the CTL Head. NO
Does the Video Envelope waveform appear at IC501 Pin 24? YES
Replace IC501.
Replace IC501. NO
Check AVCP IC.
3-7
B.
Drum Motor stopped.
Does 12V appear at PMC01 Pin 8? NO
YES
Does 2.8V appear at PMD01 Pin 12?
Check Power. NO
Does Drum PWM appear at IC501 Pin 107?
Check Connector and Drum Motor Ass’y.
NO
YES
Check the Components and foil Pattern between IC501 Pin 26 and PMC01 Pin 12 for shorts.
Do DFG Pulses appear at PMD01 Pin 3? NO
YES
Do DFG Pulses appear at IC501 Pin 104? YES
Check Drum Monitor Ass’y. NO
Check the Components and foil pattern between PMC01 Pin 11 and IC501 Pin 104 for shorts.
Does the Drum PWM waveform appear at IC501 Pin 107? YES
NO
Check the Components and foil Pattern Connected to IC501 Pin 107 PMC01 Pin 12 for shorts.
Replace IC501.
3-8
C. Capstan Motor Stopped.
Does 13VA appear at PMC01 Pin 2? NO
YES
Does 2.8V appear at PMC01 Pin 9?
Check Power. NO
YES
Check Connector and Capstan Motor Ass’y.
Does PWM wave appear at IC501 Pin 108? NO
YES
Check the Components and foil Patterns Connected between IC501 Pin 108 and PMC01 Pin 9 for shorts.
Does the CFG signal appear at PMC01 Pin 1? NO
YES
Does the CFG signal appear at IC501 Pin 9? YES
Check Capstan Motor Ass’y. NO
Check Components and foil patterns between PMC01 Pin 7 and IC501 Pin 9 for shorts.
Does Capstan PWM appear at IC501 Pin 108? YES
NO
Check the components and foil pattern connected between IC501 Pin 108 and PMC01 Pin 9 for shorts
Replace IC501.
3-9
3. System & Front Panel Circuit A. Auto stop.
Does SW30 waveform appear at IC501 Pin 105? YES
NO
Do Take-up reel pulses appear at IC501 Pin 49? YES
Check the Drum Motor Signal. NO
Do Take-up reel pulses appear at the base of Q514?
Change IC501.
NO
YES
Does 5.3V appear at RS501. YES
Replace the Take-Up Reel Photocoupler in the Deck(RS501).
3-10
NO
Check the Power.
B. Cassette tape loading is unstable.
Is REG 14VA applied to PMC01 Pin 8? YES
NO
Is High signal applied to IC501 Pin 30 when inserting the CST?
Check the power. NO
Is 5.4VA applied to R544? YES
YES
Does Low signal occur form PMC01 Pin 10 when inserting the CST? YES
NO
Check the CST SW and peripheral circuitry.
Check the power.
NO
Check the Deck Mechanism.
Check IC501 Pins 68, 69, 70, 71.
NOTE : Auto stop may also be caused by lack of lubrication,due to dried grease or oil. C. Non working finction buttons.
Is the voltage of IC501 Pin 36, 5V? YES
NO
Does(LED Ass’y) display change when a function button is pressed? YES
Check the power. NO
Replace IC501.
Check IC506 Pins 6~14, 17, Pins 20~23 pulse output.
Replace the defective switch.
Replace IC506.
3-11
4. Y/C CIRCUIT (1) No Video in EE Mode,
No Video in EE Mode
Does the Video signal appear at the IC301 Pin 48?
NO
Check the Video Input Jack. (Line In Jack)
YES
NO Is 5V applied to the IC301 Pins 18, 24, 42, 55, 72, 91?
Check the 5.2VT, 5.4VA Line. (Power Circuit)
YES Does the Video signal appear at the IC301 Pin 65?
NO
YES Does the Video signal appear at the IC501 Pin 19?
Is I2C BUS signal applied to the IC301 Pins 68, 69?
NO
Check the System Circuit. (Refer to ‘SYSTEM I2C BUS CHECK Trouble Shooting’)
YES
NO
Chck the path of the signal between the IC301 Pin 5 and IC501 Pin 17.
YES Does the Video signal NO appear at the Emitter terminal of the Q307, Q308?
Check C316. (AGC) YES
Does the 12VT, 5.4VA NO appear at the Emitter terminal of the Q307, Q308.
Replace the IC301.
YES Replace the Q307, Q308.
3-12
Check the 12VT, 5.4VA Line. (Power Circuit)
3. Y/C CIRCUIT (2) When the Y(Luminance) signal doesn’t appear on the screen in PB Mode, Is 5.2VT, 5.4VA applied to the IC301 Pins 24, 42, 55, 72, 91?
NO
Check the line of the 5.2V Line. (Power Circuit)
YES Is the I2C Bus siganl applied NO to the IC301 Pins 68, 69 ?
Refer to ‘SYSTEM I2C BUS CHECK Trouble Shooting’.
YES NO Does the normal RF signal appear at the IC301 Pin 78?
NO Is the V.H.S/W signal applied to the IC301 Pin 70?
Check the System Circuit. (IC501 Pin 105)
YES Is V.H.S/W “H” about 3.4V at the IC301 Pin 70?
NO
Check the V.H.S/W level. (Check R303, R304)
YES YES
Clean the Drum.
Does the Y(Luminance) RF NO signal appear at the IC301 Pin 76?
NO
Check the path of the Y(Luminance) RF signal. (Check the C312)
YES
Check the path of the Y(Luminance) RF signal. (Check C327)
YES
YES Is the Y(Luminance) Video waveform showed up at theIC301 Pin 43?
NO
YES Replace the IC301.
3-13
Replace the IC301.
3. Y/C CIRCUIT (3) When the C(Color) signal doesn’t appear on the screen in PB Mode, Is 5.2VT/5.4VA applied to the IC301 Pins 24, 42, 55, 72, 91.
NO
Check the line of the 5.2VT/ 5.4VA Line. (Power Circuit)
NO
Check the Color Rotary Circuit. (IC501 pin 99 )
NO
Check the Color Rotary level. (Check the R303)
YES Is the Color Rotary signal applied to the IC301 Pin 70? YES Is Color Rotary “H” about 3.4V? YES Does the Color signal appear at the IC301 Pin 25 ?
YES
NO
Does the X301(4.43MHZ) oscillate?
NO Does the Color signal appear at the IC301 Pin 21? YES
Replace the IC301.
NO
Replace the IC301.
3-14
Replace the X301.
Check the Color Pass.
3. Y/C CIRCUIT (4) When the Video signal doesn’t appear on the screen in REC Mode,
Is the EE signal normal?
NO
Check EE Mode.
YES Is 5.2VT/5.4VA applied to the IC301 Pins 24,42,55,72,91?
NO
Check the line of the 5.2VT/ 5.4VA Line.(Power Circuit)
YES Does PB Mdoe operate normally?
NO
Check PB Mode.
YES Does the RF signal appear at the IC301 Pin 78?
NO
Is the REC ‘H’ signal (about 4V) applied to the IC301 Pin 80?
NO
Check the System of REC ‘H’. (the IC501 Pin 47 / the D301)
YES YES
Does the REC RF signal appear at the IC301 Pins 88,89,94,95?
NO
Check REC Luminance Pass & Color Pass.
YES
Check the circuit of the IC301 Pins 85, 86.
YES
YES Check the Drum & Drum Connector
3-15
Replace the IC301.
5. Tuner/IF circuit (1) No picture on the TV screen No picture on the TV screen YES Does the Video signal at the TU701 Pin24?
NO
Is +30VT applied to TU701 Pin 16?
YES
NO
Check 33VT line.
YES Is +5VT applied to TU701 Pin 13?
NO
Check 5VT line.
YES Does the Clock signal appear at TU701 Pin 11?
NO
Check the liC Clock signal of µ-com Pin 59.
NO
Check the liC Data signal of µ-com Pin 60.
YES Does the data signal appear at TU701 Pin 12? YES
Replace Tuner
Does Sync appear at IC501 Pin111?
NO
Check the signal flow from TU701 Pin 24 to IC301 Pin 67.
YES Check the signal flow from IC501 Pin19 to JK901 Pin19.
3-16
(2) No sound (Mono Model) No sound YES Check the Vcc of IC301 Pin 18.
NO
Check 5VT power.
YES Check the Tuner Audio signal at IC301 Pin 13.
NO
Chekc the signal flow from TU701 Pin21 to IC301 Pin 13.
YES Check the Audio signal at IC301 Pin 11.
NO
YES Check the signal flow from IC301 pin 11 to IC901 Pin 6.
3-17
Replace IC301.
(3) No sound (Hi-Fi Model) No sound YES Check the Vcc of IC751 Pins 1, 19, 33.
NO
Check 5V power.
YES Check the Tuner SiF signal at IC751 Pin 2.
NO
Check the Tuner Audio of TU701 Pin 21.
YES Check the oscillator of IC751 Pins 5, 6.
NO
Replace X751.
YES Check the Audio of IC751 Pins 30, 31.
NO
Check the IIC Clock and Data at IC751 Pins 12, 13.
NO
Check the signal flow from IC751 Pins 30, 31 to IC801 Pins 2,3.
NO
Check the IIC Clock and Data at IC801 Pins 42, 43.
YES Check the Audio of IC801 Pins 2, 3. YES Check the Audio of IC801 Pins 18, 19. YES Check the signal flow from IC801 pins 18, 19 to JK901 Pins 1, 3.
3-18
6. Hi-Fi Circuit (Hi-Fi Model)
A. Hi-Fi Playback.
YES
No sound
Check the Vcc of IC801.(Pins 34, 40) NO YES
Check the Hi-Fi Selection Switch and the Tape quality.
Check power.
YES
Is the RF Envelope at IC801 Pin 44 over 2Vp-p?
NO
YES
YES
Check the connection at P3D01 if good then Replace IC801.
Check IC801 Pin 42(Data), Pin 43(Clock). YES
NO
Do Audio signals appear at IC801 Pin 16(L-CH), 17(R-CH)? YES
Check the Signal path of Audio Output.
Is the Head switching signal IC802 Pin 41 O.K?
Check Ports of µ-COM. NO
Replace IC801.
3-19
NO
Check IC501 Pin 23. (Audio head switch 25)
B. Hi-Fi REC.
It is impossible to record and playback Hi-Fi Audio signal. YES
Check Vcc of IC801. (Pins 34,40) YES
NO
Check IC801 Pin 42(Data),Pin 43(CLOCK). YES
Check Power. NO
Do Audio signals appear at IC801 Pins 16, 17? YES
Check ports of µ-COM. NO
Do FM Audio signals appear at IC801 Pin 36? YES
Check Audio input signal of IC801 Pins 2, 3(TU.A.), 6, 7(Scart 1) NO
Check the Contact Points of Drum Connector if good then Replace the Drum.
Replace IC801.
3-20
SECTION 4 MECHANISM CONTENTS DECK MECHANISM PARTS LOCATIONS • •
Top View...................................................4-1 Bottom View ............................................4-1
DECK MECHANISM DISASSEMBLY 1. Drum Assembly .........................................4-2 2. Plate Top ...................................................4-4 3. Holder Assembly CST ...............................4-4 4. Opener Door .............................................4-4 5. Bracket Assembly L/D Motor.....................4-4 6. Gear Assembly Rack F/L ..........................4-4 7. Arm Assembly F/L .....................................4-4 8. Lever Assembly S/W .................................4-4 9. Arm Assembly Cleaner..............................4-5 10.Head F/E ...................................................4-5 11. Base Assembly A/C Head .........................4-5 12.Brake Assembly RS ..................................4-6 13.Brake Assembly T .....................................4-6 14.Arm Assembly Tension..............................4-6 15.Reel S / Reel T..........................................4-6 16.Base Assembly P4 ....................................4-7 17.Opener Lid ................................................4-7 18.Arm Assembly Pinch .................................4-7 19.Lever T/up / Arm T/up ...............................4-7 20.Belt Capstan/Motor Capstan .....................4-8 21.Lever F/R ..................................................4-8 22.Clutch assembly D35 ................................4-8 23.Bracket Assembly Capstan .......................4-8 24.Gear Drive/Gear Cam ...............................4-9 25.Gear Sector...............................................4-9 26.Plate Slider................................................4-9 27.Lever Tension ............................................4-9 28.Lever Spring..............................................4-9 29.Gear Assembly P2/ Gear Assembly P3 ..................................4-10 30.Base Assembly P2/ Base Assembly P3 ..................................4-10 31.Base Loading ..........................................4-11 32.Base Tension ...........................................4-11 33.Arm Assembly Idler Jog ..........................4-11
DECK MECHANISM ADJUSTMENT • Tools and Fixtures for Service.............4-12 1. Mechanism and Mode Switch Alignment Check ......................................................4-13 2. Deck Preparation for Adjustment ............4-14 3. Checking Torque .....................................4-14 4. Guide Roller Height Adjustment..............4-15 4-1. Preliminary Adjustment ....................4-15 4-2. Precise Adjustment ..........................4-15 5. Audio/Control (A/C) Head Adjustment ....4-16 5-1. Preliminary Adjustment ....................4-16 5-2. Confirmation of Tape Path between Pinch Roller and Take-up Guide .....4-17 5-3. Precise Adjustment(Azimuth Adjustment) .........................................................4-17 6. X-Value Adjustment .................................4-17 7. Adjustment after Replacing Drum Assembly (Video Heads) .........................................4-18 8. Check the Tape Travel after Reassembling Deck Mechanism.....................................4-18 8-1. Checking Audio and RF Locking Time during Playback after CUE or REV .........................................................4-18 8-2. Checking Tape Curling or Jamming .........................................................4-18
MAIN TENANCE/INSPECTION PROCEDURE 1. 2. 3. 4.
Check before starting Repairs ................4-19 Required Maintenance ............................4-20 Scheduled Maintenance..........................4-20 Supplies Required for Inspection and Maintenance............................................4-20 5. Maintenance Procedure ..........................4-20 5-1. Cleaning...........................................4-20 5-2. Greasing ..........................................4-21
MECHANISM TROUBLESHOOTING GUIDE 1. Deck Mechanism.....................................4-23 2. Front Loading Mechanism.......................4-26
EXPLODED VIEWS 1. Front Loading Mechanism Section .........4-28 2. Moving Mechanism Section (1)...............4-29 3. Moving Mechanism Section (2)...............4-30
DECK MECHANISM PARTS LOCATIONS • Top View Pracedure Starting No. 1 2 2 3 2 4 5
2
6 3
7
4 9 5 11
10 18
1
16
31
17 19 19 12
14 15
8
33
13 15
• Bottom View
20 24
30 29 29
23
30
20
25 32 27 26 28
24 22 21
NOTE : When reassembly perform the procedure in the reverse order. 1) When reassembling, confirm Mechanism and Mode Switch Alignment Position (Pefer to Page 4-14) 2) When disassembling, the Parts for Starting No. Should be removed first.
4-1
2,3,4 2,3,4,6
6 7 8 9 10 11 2,3 12 2,3 13 2,3 14 2,3,12,13, 15 14 16 17 17 18 17 19 17,18 20 20, 21
21 22 23 24 25 26
Part
Fixing Type
Fig- Viure ew
Drum Assembly Plate Top Holder Assembly CST Opener Door Bracket Assembly L/D Motor Gear Assembly Rack F/L Arm Assembly F/L Lever Assembly S/W Arm Assembly Cleaner Head F/E Base Assembly A/C Head Brake Assembly RS Brake Assembly T Arm Assembly Tension Reel S/Reel T
3 Screw 2 Hook Chassis Hole Chassis Hole 3 Hook
A-1 A-2 A-2 A-2 A-2
T T T T T
1 Hook, Chassis Hole Chassis Hole 1 Hook Chassis Embossing Chassis Embossing 1 Screw 1 Hook 1 Hook 2 Hook
A-2 A-2 A-2 A-3 A-3 A-3 A-4 A-4 A-4 A-4
T T T T T T T T T T
Base Assembly P4 Opener Lid Arm Assembly Pinch Lever T/Up / Arm T/Up
Chassis Embossing Chassis Embossing Shaft 1 Hook
A-5 A-5 A-5 A-5
T T T T
Belt Capstan/Motor Capstan Lever F/R Clutch Assembly D35 Break Assembly Capstan Gear Drive/Gear Cam Gear Sector Plate Slider
3 Screw Locking Tab Washer Locking Tab Washer/Hook 1 Hook Shaft Guide
A-6 A-6 A-6 A-6 A-7 A-7 A-7
B B B B B B B
1 Hook
A-7
B
Locking Tab
A7
B
Boss Chassis Slot
A-8 A-8
B B
1 Screw
A-9
T
Chassis Embossing Locking Tab
A-9 A-9
B T
20,21,23, 24,25 20,21,23, 27 Lever Tension 24,25,26 2,3,14,20, 28 Lever Spring 21,25,23, 24,26 25 29 Gear Assembly P2/Gear Assembly P3 2,3,14,25, 30 Base Assembly P2/Base Assembly P3 29 2,3,14,25, 31 Base Loading 29 2,3,14 32 Base Tension 2,3,20,21, 33 Arm Assembly Idler 22
R: Top, B:Bottom
DECK MECHANISM DISASSEMBLY Stator
(S2) (S2) (S3)
Drum Motor
(S3) Rotor
Drum Sub Assembly (A) Drum FPC
Carbon Brush
(S1) (S1) (S1) H2
H1
Holder FPC
Fig. A-1 1. Drum Assembly (Fig. A-1-1)
(Fig. B-1)
1) Unplug the Drum FPC Connector. 2) Remove three Screws(S1) on bottom side and separate the Drum assembly. 3) Unhook (H1), (H2) and separate the Holder FPC and Cap FPC.
Cap FPC
1-1. Drum Motor 1) Remove two Screws(S2) and disassemble the Stator of the Drum Motor. (2) Remove two Screws(S3) and separate the Rotor of the Drum Motor from the Drum Sub assembly.
Drum FPC Holder FPC
NOTE When reassembling, confirm (A) portion of the Drum Sub assembly whether the Carbon Brush is in there or not.
Figure in the opposite direction
4-2
DECK MECHANISM DISASSEMBLY
Plate Top
(Fig. A-2-1)
(C)
(B') (B)
Holder Assembly CST
(Fig. A-2-2)
(E)
Arm Assembly F/L
(Fig. A-2-6)
Lever Assembly S/W
(Fig. A-2-7)
(H8)
(C1)
Brackert Assembly L/D Motor Spring Lever S/W
(Fig. A-2-4)
(C')
(D)
(E')
Opener Door
(H6)
(Fig. A-2-3)
Chassis (A) Gear Assembly Rack F/L
(Fig. A-2-5)
Fig. A-2 4-3
(B)
DECK MECHANISM DISASSEMBLY 2. Plate Top (Fig. A-2-1) 1) Pull the (B) portion of the Plate Top back in direction of arrow and separate the right side of it. 2) pull the (B’) portion of the Plate Top back in direction of arrow and separate the left side of it. (Used tools : (-) type Drive, anything tool with sharp point or flat point.)
2) Unhook three Hooks(H3,H4,H5) on bottom side of the Chassis, lift up the Bracket assembly L/M and disassemble the Bracket assembly L/D Motor.
Bracket assembly L/M
(H4)
(H3)
NOTE (1) When reassembling, push the Plate Top after alignment the two position(C), (C’) as Fig.
(H5)
6. Gear Assembly Rack F/L (Fig. A-2-5) (C') (C) (B')
(B)
1) Move the Gear Assembly Rack F/L in direction of arrow(A) and unhook the Hook(H6) pulling back in front. 2) Separate the Rear Rack F/L in direction of arrow(B).
NOTE When reassembling, align the Gear part of the Gear Assembly Rack F/L with the Gear Drive as below Fig.
3. Holder Assembly CST (Fig.A-2-2)
Gear Rack F/L
1) Move the Holder assembly CST in direction of arrow and separate the left side of it first through the (D) position of the Chassis. Holder assembly CST
Chassis Gear Drive
(D)
7. Arm assembly F/L (Fig. A-2-6) 1) Move the Arm assembly F/L in direction of arrow and separate the left side of it first. 2) Disassemble the Arm assembly F/L from each guided Hole of the Chassis.
2) Disassemble the right side of the Holder assembly CST from each guided hole of the Chassis.
NOTE When reassembling, insert the (E) part of the Holder assembly CST in the (E’) hole of the Chassis first and assemble the left side of it.
8. Lever assembly S/W(Fig. A-2-7) 1) Hook the Spring Lever S/W on the Hook(H7) first as below Fig. 2) Unhook the Hook(H8) in the left side of the Chassis and move the Lever assembly S/W. Chassis
4. Opener Door (Figure. A-2-3) 1) Turn the Opener Door clockwise and remove it through the guide hole of the chassis.
5. Bracket assembly L/D Motor(Fig. A-2-4) 1) Unplug the Connector(C1).
(H8) (H7)
Spring Lever S/W
4-4
DECK MECHANISM DISASSEMBLY
Arm Assembly Cleaner (Fig. A-3-1) (A)
(S4) Base Assembly A/C Head
(A)
*(Fig. A-3-3)
Head F/E (Fig. A-3-2)
Chassis
Fig. A-3 9. Arm assembly Cleaner (Fig. A-3-1)
11. Base assembly A/C Head (Fig. A-3-3)
1) Breakaway the (A) portion as Fig. A-3-1 from the Embossing of the Chassis, turn the Arm assembly Cleaner to clockwise direction and lift it up.
1) Remove the Screw(S4) and lift the Base assembly A/C Head up.
10. Head F/E (Fig. A-3-2) 1) Breakaway the (A) portion of the Head F/E from the Embossing of the Chassis, turn it to counterclockwise direction and lift it up.
4-5
DECK MECHANISM DISASSEMBLY Arm Assembly Tension
(Fig. A-4-3) (H11)
Spring TB Brake Assembly T
(Fig. A-4-1)
Spring Tension
Reel S Reel T
(Fig. A-4-4)
(Fig. A-4-4) Spring RS
Brake Assembly RS
(Fig. A-4-2)
(H12) (H9) (H10)
Base Tension
Chassis
Fig. A-4 12. Brake assembly T (Fig. A-4-1) 1) Unhook the Spring TB from the Hook(H9) of the Chassis. 2) Lift the Brake assembly T up.
NOTE Difference for Springs (Difference for Springs)
Spring TB Spring RS Spring Tension
13. Brake assembly RS (Fig. A-4-2) 1) Unhook the Spring RS from the Hook(H10) of the Chassis.. 2) Lift the Brake assembly T up.
14. Arm assembly Tension (Fig. A-4-3)
Color (Black)
15. Reel S / Reel T (Fig. A-4-4) 1) Difference for Reel S / Reel T
1) Unhook the Spring Tension from the Hook(H11) of the Arm assembly tension. 2) Unhook the Hook(H12) of the Base Tension and lift the Arm assembly Tension up.
Reel S
Reel T
4-6
DECK MECHANISM DISASSEMBLY
Opener Lid
(Fig. A-5-2)
(B)
(B)
Arm Assembly Pinch
(Fig. A-5-3) (C) Base Assembly P4
Lever T/up
(Fig. A-5-1)
(H13)
(Fig. A-5-4) (C)
Arm T/up
(H13)
(Fig. A-5-5) (A)
Chassis
Fig. A-5 16. Base assembly P4 (Fig. A-5-1) 1) Breakaway the (A) portion of the Base assembly P4 from the Embossing of the Chassis. 2) Turn the Base assembly P4 to counterclockwise direction and lift it up.
17. Opener Lid (Fig. A-5-2) 1) Breakaway the (B) portion of the Opener Lid from the Embossing of the Chassis. 2) Turn the Opener Lid to clockwise direction and lift it up.
18. Arm assembly Pinch (Fig. A-5-3) 1) Lift the Arm assembly Pinch up.
4-7
19. Lever T/up (Fig. A-5-4)/ Arm T/up (Fig. A-5-5) 1) Unhook the Hook(H13) of the bottom Chassis and lift the Lever T/up up. 2) Lift the Arm T/up up.
NOTE When reassembling, confirm the (C) portion of the Arm assembly Pinch is inserted to the Chassis Hole correctly as Fig. Place the Mechanism face down, or up side down.
DECK MECHANISM DISASSEMBLY
Belt Capstan
(Fig. A-6-1)
Motor Capstan
(Fig. A-6-2) Washer(W1)
Clutch Assembly D35
(Fig. A-6-4)
(L1)
(L1)
Brake Assembly Capstan
(Fig. A-6-5) Lever F/R
(Fig. A-6-3) (L2)
Chassis
(S5)
Fig. A-6 20. Belt Capstan (Fig. A-6-1)/ Motor Capstan (Fig. A-6-2) 1) Remove the Belt Capstan. 2) Remove the three Screws(S5) on bottom Chassis and lift the Motor Capstan up.
21. Lever F/R (Fig. A-6-3) 1) Unlock the Locking Tab(L1) as Fig. A-6-3 and lift the Lever F/R up.
22. Clutch assembly D35 (Fig. A-6-4) 1) Remove the Washer(W1) and lift the Clutch assembly D35 up.
23. Brake assembly Capstan (Fig. A-6-5) 1) Pull the Locking Tab(L2) back in direction of arrow and lift it up.
4-8
DECK MECHANISM DISASSEMBLY
(H14)
Gear Cam Hole(B)
Gear Cam Gear Drive Hole(A)
(Fig. A-7-2) Gear Sector
Washer (W2)
(Fig. A-7-3) Plate Slider
Gear Drive
(Fig. A-7-4)
(Fig. A-7-1)
(A)
Lever Tension
(Fig. A-7-5) Lever spring (L3)
(Fig. A-7-6)
Gear Drive Hole(C) Base Loading (H15)
(H16)
Chassis
Fig. A-7 24. Gear Drive (Fig. A-7-1)/ Gear Cam (Fig. A-7-2) 1) Remove the Washer(W2) and lift the Gear Drive up. 2) Unhook the Hook(H14) of the Gear Cam and lift the Gear Cam up.
NOTE When reassembling, align the Gear Drive Hole(A) and the Gear Cam Hole(B) in a straight line after the Gear Drive Hole(C) is aligned with the Chassis Hole as Fig.
25. Gear Sector (Fig. A-7-3) 1) Unhook the Hook(H15) of the Base Loading on bottom Chassis and lift the Gear Sector up.
4-9
26. Plate Slider (Fig. A-7-4) 1) Just lift the Plate Slider up.
27. Lever Tension (Fig. A-7-5) 1) Unhook the (A) portion of the Lever Tension from the Hook(H16) of the Chassis. 2) Turn the Lever Tension to counterclockwise direction and lift it up.
28. Lever Spring (Fig. A-7-6) 1) Unlock the Locking Tab(L3) of the bottom Chassis and lift the Lever Spring up.
DECK MECHANISM DISASSEMBLY Gear assembly P2 Hole Gear assembly P3 Hole
Gear Assembly P3
(Fig. A-8-2)
Lever spring Boss
Gear sector Hole(A) Gear Assembly P2 Plate slider Hole(B)
(Fig. A-8-1)
(B)
(A)
Chassis
Base Assembly P3
(Fig. A-8-4)
Base Assembly P2
Fig. A-8
(Fig. A-8-3)
29. Gear assembly P2 (Fig. A-8-1)/ Gear assembly P3 (Fig. A-8-2)/
30. Base assembly P2 (Fig. A-8-3)/ Base assembly P3 (Fig. A-8-4)
1) Just lift the Gear assembly P2 up. 2) Just lift the Gear assembly P3 up.
1) Move the Base assembly P2 in direction of arrow(A) along the Guided Hole of the Chassis and disassemble it on bottom side. 2) Move the Base assembly P3 in direction of arrow(B) along the Guided Hole of the Chassis and disassemble it on bottom side.
NOTE When reassembling, align the two Holes of the Gear assembly P2 and P3 in a straight line after confirmation whether the Gear Sector Hole(A) and the Plate Slider Hole(B) are aligned or not as Fig.
Place the Mechanism face down, or return to original position.
4-10
DECK MECHANISM DISASSEMBLY
Base Tension
(S7) Base Loading
(Fig. A-9-2)
Arm Assembly Idler Jog
(Fig. A-9-1)
(A)
(B)
(D)
(Fig. A-9-3)
(C)
Chassis
Fig. A-9 31. Base Loading (Fig. A-9-1)
33. Arm assembly Idler (Fig. A-9-3)
1) Remove the Screw(S7). 2) Lift the Base Loading up.
1) Make narrower the two parts, (A) and (B), as Fig. A-9-3. 2) Lift the Arm assembly Idler up.
32. Base Tension (Fig. A-9-2) 1) Breakaway the (A) portion of the Base Tension from the Embossing of the Chassis. 2) Turn the Base Tension to counterclockwise direction and lift it up.
4-11
NOTE When disassembling, be careful not to be caught the (D) part by the Chassis as Fig.
DECK MECHANISM ADJUSTMENT • Tools and Fixfures for Service
SR K
1. Cassette Torque meter 1. PUJ42881 1.
-V
HT
-S
2. Alignment tape MHPE
3. Torque gauge 3. PUJ48075-2 3.
300
250 200 150
0 50
SR
VID K CAS EO S TOR ETTE Q MET UE VHT- ER 303
-T K- V HT0 SR 50 100 150 200 300
250
4. Post height adjusting driver (Roller driver) PTU94002
4-12
DECK MECHANISM ADJUSTMENT 1.Mechanism Alignment Position Check Purpose:To determine if the Mechanism is in the correct position, when a Tape is ejected. Test Equipment/ Fixture
Test Conditions (Mechanism Condition)
• Blank tape
• Eject Mode (with Cassette ejected)
1) Turn the Power S/W on and eject the Cassette by pressing the Eject Button. 2) Remove the Top Cover and Plate Assembly Top, visually check if the Gear Cam Hole is aligned with the Chassis Hole as below Fig. C-2. 3) IF not, rotate the Shaft of the Loading Motor to either Clockwise or Counterclockwise until the Alignment is as below Fig. C-2.
Check Point • Mechanism and Mode Switch Position
4) Remove the Screw which fixes the Deck Mechanism and Main Frame and confirm if the Gear Cam is aligned with the Gear Drive as below Fig. C-1(A). 5) Confirm if the Mode S/W on the Main P.C.Board is aligned as below Fig. C-1(B). 6) Remount the Deck Mechanism on the Main P.C.Board and check each operation.
CHECK DIAGRAM
Gear Cam
(C)
Mode S/W
(B)
Gear Drive Gear Cam (o) and Gear Drive (o) groove alignment
BOTTOM VIEW Fig. C-1
L/D Motor Assembly
Gear Cam (B)
(A')
(A)
(B') Chassis Hole
TOP VIEW Fig. C-2
4-13
Gear Cam Hole
Gear Cam Hole
DECK MECHANISM ADJUSTMENT Cassette without Tape. Cover the Holes of the End Sensors at the both sides of the Bracket Side(L) and Bracket Assembly Door to prevent a light leak. Then The Deck Mechanism drives to the Stop Mode. In this case, The Deck Mechanism can accept inputs of each mode, however the Rewind and Review Operation can not be performed for more than a few seconds because the Take-up Reel Table is in the Stop State and can not be detected the Reel Pulses.
2. Preparation for Adjustment (To set the Deck Mechanism to the Loading state without inserting a Cassette Tape). 1) 2) 3) 4)
Unplug the Power Cord from the AC Outlet. Disassemble the Top Cover and Plate Assembly Top. Plug the Power Cord into the AC Outlet. Turn the Power S/W on and push the Lever Stopper of the Holder Assembly CST to the back for Loading the
3. Checking Torque
Purpose: To insure smooth Transport of the Tape during each Mode of Operation. If the Tape Transport is abnormal, then check the Torque as indicated by the chart below. Test Conditions (Mechanism Condition)
Test Equipment/ Fixture • Torque Gauge(600g/cm ATG) • Torque Gauge Adaptor • Cassette Torque Meter
Checking Method
• Play (FF) or Review (REW) Mode • Perform each Deck Mechanism Mode without inserting a Cassette Tape(Refer to above No.2 Preparation for Adjustment). • Read the Measurement of the Take-up or Supply Reels on the Cassette Torque Meter(Fig. C-3-2). • Attach the Torque Gauge Adaptor to the Torque Gauge and then read the Value of it(Fig. C-3-1). Mode
Item
Test Equipment
Measurement Reel
Measurement Values
Fast Forward Torque
Fast Forward
Cassette Torque Gauge
Rewind Torque
Rewind
Cassette Torque Gauge Supply Reel
More than 400g/cm
Play Take-Up Torque
Play
Cassette Torque Meter
Take-Up Reel
40~100g/cm
Review Torque
Review
Cassette Torque Meter
Supply Reel
120~210g/cm
NOTE:
Take-Up Reel
More than 400g/cm
NOTE:
The Values are measured by using a Torque Gauge and Torque Gauge Adaptor with the Torque Gauge affixed.
• Cassette Torque Meter
The Torque reading to measure occurs when the Tape abruptly changes direction from Fast Forward of Rewind Mode, when quick bracking is applied to both Reels.
• Torque Gauge
SR K
Torque Gauge -V
HT
-S
300 250 200 150
SR
K
0 50
VID CAS EO S TOR ETTE Q MET UE E VHT R -303
-T K- V HT0 SR 50 100 150
Torque Gauge Adaptor
200
300
250
Reel Table
Fig. C-3-2
Fig. C-3-1
4-14
DECK MECHANISM ADJUSTMENT 4.Guide Roller Height Adjustment Purpose: To regulate the Height of the Tape so that the Bottom of the Tape runs along the Tape Guide Line on the Lower Drum. 4-1. Preliminary Adjustment Test Equipment/ Fixture • Post Height Adjusting Driver
Test Conditions (Mechanism Condition) • Play or Review Mode
Adjustment Procedure
Adjustment Point • Guide Roller Height Adjustment screws on the Supply and Take-Up Guide Rollers.
ADJUSTMENT DIAGRAM
1) Confirm if the Tape runs along the Tape Guide Line of the Lower Drum. 2) If the Tape runs the Bottom of the Guide Line, turn the Guide Roller Height Adjustment Screw to Clockwise direction. 3) If it runs the Top, turn to Counterclockwise direction. 4) Adjust the Height of the Guide Roller to be guided to the Guide Line of the Lower Drum from the Starting and Ending Point of the Drum.
Guide Roller Height Adjustment screw Upper Flange Guide Roller Retaining Screw
Fig. C-4-1
4-2. Precise Adjustment Test Equipment/Fixture • Oscilloscope • Alignment Tape • Post Height Adjusting Driver
Test Equipment Connection Points • CH-1:PB RF Envelope • CH-2:NTSC: SW 30Hz PAL: SW 25Hz • Head Switching Output Point • RF Envelope Output Point
Adjustment Point
Test Conditions VCR(VCP) State
• Guide Roller Height Adjustment Screws
• Play an Alignment Tape
Waveform Diagrams P2 POST ADJUSTMENT
Adjustment Procedure 1) Play an Alignment Tape after connecting the Probe of the Oscilloscope to the RF Envelope Output Test Point and Head Switching Output Test Point. 2) Tracking Control(in PB Mode) : Center Position(When this Adjustment is performed after the Drum Assembly has been replaced, set the Tracking Control so that the RF Output is Maximum). 3) Height Adjustment Screw : Flatten the RF Waveform. (Fig. C-4-2) 4) Turn(Move) the Tracking Control(in PB Mode) Clockwise and Counterclockwise.(Fig. C-4-3) 5) Check that any Drop of RF Output is uniform at the Start and End of the Waveform.
NOTE
Turn the Roller Guide Height Adjustment Screw slightly to flatten the waveform.
P3 POST ADJUSTMENT
Fig. C-4-2
Tracking control at center
Turn(Move) the tracking control to both directions
Fig. C-4-3 Connection Diagram OSCILLOSCOPE
If the adjustment is excessive or insufficient the tape will jam or fold. RF ENVELOPE OUTPUT TEST POINT HEAD SWITCHING OUTPUT TEST POINT
4-15
DECK MECHANISM ADJUSTMENT 5. Audio/Control (A/C) Head Adjustment Purpose: To insure that the Tape passes accurately over the Audio and Control Tracks in exact Alignment in both the Record and Playback Modes. 5-1. Preliminary Adjustment (Height and Tilt Adjustment) Perform the Preliminary Adjustment, when there is no Audio Output Signal with the Alignment Tape. Test Equipment/ Fixture • Blank Tape • Screw Driver(+) Type 5mm
Test Conditions (Mechanism Condition)
Adjustment Point • Tilt Adjustment Screw(C) • Height Adjustment Screw(B) • Azimuth Adjustment Screw(A)
• Play the blank tape
Adjustment Procedure/Diagrams 1) Initially adjust the Base Assembly A/C Head as shown Fig. C-5-1 by using the Height Adjustment Screw(B). 2) Play a Blank Tape and observe if the Tape passes accurately over the A/C Head without Tape Curling or Folding. 3) If Folding or Curling is occured then adjust the Tilt Adjustment Screw(C) while the Tape is running to resemble Fig. C-5-3.
4) Reconfirm the Tape Path after Playback about 4~5 seconds.
NOTE Ideal A/C head height occurs, when the tape runs between 0.2~0.25mm above the bottom edge of the A/C head core.
Tape
A/C Head P4
10.9
Tape 0.2~0.25mm
A/C Head Base Fig. C-5-3
Fig. C-5-1 X-Value Adjustment Hole
Fixed Screw
Azimuth Adjustment Screw(A)
Tilt Adjustment Screw(C) Height Adjustment Screw(B)
A/C Head Assembly Fig. C-5-2
4-16
DECK MECHANISM ADJUSTMENT 5-2. Confirm that the Tape passes smoothly between the Take-up Guide and Pinch Roller(using a Mirror or the naked eye). 1)
After completing Step 5-1.(Preliminary Adjustment), check that the Tape passes around the Take-up Guide and Pinch Roller without Folding or Curling at the Top or Bottom. (1) If Folding or Curling is observed at the Bottom of the Take-up Guide then slowly turn the Tilt Adjustment Screw(C) in the Clockwise direction. (2) If Folding or Curling is observed at the Top of it then
slowly turn the Tilt Adjustment Screw(C) in the Counterclockwise direction.
NOTE: Check the RF Envelope after adjusting the A/C Head, if the RF Waveform differs from Fig. C-5-4, performs Precise Adjustment to flat the RF Waveform.
5-3. Precise Adjustment (Azimuth adjustment) Connection Point
Test Equipment/ Fixture • Oscilloscope • Alignment Tape(SP) • Screw Driver(+) Type 5mm
• Audio output jack
Test Conditions (Mechanism Condition) • Play an Alignment Tape 6KHz Section
Adjustment Point • Azimuth Adjustment Screw(A) • Height Adjustment Screw(B)
Adjustment Procedure
6KHZ
1) Connect the Probe of the Oscilloscope to Audio Output Jack. 2) Alternately adjust the Azimuth Adjustment Screw(A) and the Tilt Adjustment Screw(C) for Maximum Output of the 6Khz segment.
A:Maximum
Fig. C-5-4
6. X-Value Adjustment Purpose: To obtain compatibility with other VCR(VCP) Models. Test Equipment/ Fixture • Oscilloscope • Alignment tape(SP only) • Screw Driver(+) Type 5mm
Connection Point • CH-1: PB RF Envelope • CH-2: NTSC: SW 30Hz PAL: SW 25Hz • Head Switching Output Test Point • RF Envelope Output Test Point
Adjustment Procedure 1) Release the Automatic Tracking to run long enough for Tracking to complete it’s Cycle. 2) Loosen the Fixed Mounting Screw and move the Base Assembly A/C Head in the direction as shown in the Diagram to find the center of the peak that allows for the maximum Waveform Envelope. This method should allow the 31um Head to be centrally located over the 58um Tape Track. 3) Tighten the Base Assembly A/C Head mounting Screw.
Test Conditions (Mechanism Condition)
Adjustment Point
• Play an Alignment Tape Left
Groove at the Base A/C
Right
Adjustment Diagram X-Value Adjustment Hole
Fixed Screw Azimuth Adjustment Screw(A)
Tilt Adjustment Screw(C) Height Adjustment Screw(B)
OSCILLOSCOPE
Connection Diagram RF ENVELOPE OUTPUT TEST POINT CH-1 CH-2
HEAD SWITCHING OUTPUT TEST POINT
4-17
DECK MECHANISM ADJUSTMENT 7. Adjustment after Replacing Drum Assembly (Video Heads) Purpose: To correct for shift in the Roller Guide and X value after replacing the Drum. Test Equipment/ Fixture • Oscilloscope • Alignment tapes • Blank Tape • Post Height Adjusting Driver • Screw Driver(+) Type 5mm
Test Conditions (Mechanism Condition)
Connection Point • CH-1: PB RF Envelope • CH-2: NTSC: SW 30Hz PAL: SW 25Hz • Head Switching Output Test Point • RF Envelope Output Test Point
Checking/Adjustment Procedure
Adjustment Points • Guide Roller Precise Adjustment • Switching Point • Tracking Preset • X-Value
• Play the blank tape • Play an alignment tape
Connection Diagram
OSCILLOSCOPE
Play a blank tape and check for tape curling or creasing around the roller guide. If there is a problem then follow the procedure RF ENVELOPE OUTPUT TEST POINT 4. "Guide Roller Height" and 5. "Audio Control(A/C) Head HEAD SWITCHING OUTPUT TEST Adjustment".
CH1 CH2
POINT
Waveform V1/V MAX < = 0.7 V2/V MAX < = 0.8 RF ENVELOPE OUTPUT
V1
V
V2
Fig. C-7
8. Check the Tape Travel after Reassembling Deck Assembly. 8-1.Check Audio and RF Locking Time during playback and after CUE or REV (FF/REW)
• Oscilloscope • Alignment tapes(with 6H 3kHz Color Bar Signal) • Stop Watch
Test Equipment Connection Points Points Connection
Specification
Test Equipment/ Fixture
• RF Locking Time: Less than 5 sec. • Audio Locking Time:Less than 10sec
Checking Procedure
• CH-1: PB RF Envelope • CH-2: Audio Output • RF Envelope Output Point • Audio Output Jack
Test Conditions (Mechanism Condition) • Play an alignment tape (with 6H 3kHz Color Bar Signal)
NOTES:
Play an alignment tape then change the operating mode to CUE or REV and confirm if the unit meets the above listed specifications.
1) CUE is fast forward mode (FF) 2) REV is the rewind mode (REW) 3) Referenced to the Play mode
8-2.Check for tape curling or jamming Test Equipment/ Fixture • T-160 Tape • T-120 Tape
Specification
Test Conditions VCR(VCP) (Mechanism State Condition)
• Be sure there is no tape jamming or curling at • Run the CUE, REV play mode at the the begining, middle or end of the tape. beginning and the end of the tape.
Checking Procedure 1) Confirm that the tape runs smoothly around the roller guides, drum and A/C head assemblies while abruptly changing operating modes from Play to CUE or REV. This is to be checked at the begining, middle and end sections of the cassette.
2) Confirm that the tape passes over the A/C head assembly as indicated by proper audio reproduction and proper tape counter performance.
4-18
MAINTENANCE/INSPECTION PROCEDURE 1 Check before starting repairs The following faults can be remedied by cleaning and oiling. Check the needed lubrication and the conditions of cleanliness in the unit. Check with the customer to find out how often the unit is used, and then determine that the unit is ready for inspection and maintenance. Check the following parts. Phenomenon
Replacement
Inspection
Color beats
F/E Head
Dirt on full-erase head
o
Poor S/N, no color
Dirt on video head
o
Vertical or Horizontal jitter
Dirt on video head Dirt on tape transport system
o
Low volume, Sound distorted
Dirt on Audio/control head
o
Dirt on pinch roller
o
Belt Capston
Clutch Assembly D33K Torque reduced
o
Clutch Assembly D33K
Tape does not run. Tape is slack In Review and Unloading (off mode), the Tape is rolled up loosely.
Video Head
Fig. C-9-1 Top VIEW A/C Head Pinch Roller
Cleaning Drum and transport system
Fig. C-9-3
NOTE If locations marked with o do not operate normally after cleaning, check for wear and replace. See the EXPLODED VIEWS at the end of this manual as well as the above illustrations See the Greasing (Page 4-22) for the sections to be lubricated and greased.
Fig. C-9-2 BOTTOM VIEW
* No. (1)~(13) Indicates the Tape Path to be traveled from Supply Reel to Take-up Reel. (6) Base Assembly P3
(3) F/E Head
(7) A/C Head (8) P4 Post (5) Drum Assembly (Video Head)
(10) Pinch Roller
(4) Base Assembly P2 (2) Tension Post
(11) Take-up Guide Post
(9) Capstan Shaft (1) Supply Reel (12) Take-up Reel
Fig. C-9-3 Tape Transport System 4-19
MAINTENANCE/INSPECTION PROCEDURE 2. Required Maintenance The recording density of a VCR(VCP) is much higher than that of an audio tape recorder. VCR(VCP) components must be very precise, at tolerances of 1/1000mm, to ensure compatiblity with other VCRs. If any of these components are worn or dirty, the symptoms will be the same as if the part is defective. To ensure a good picture, periodic inspection and maintenance, including replacement of worn out parts and lubrication, is necessary.
3. Scheduled Maintenance Schedules for maintenance and inspection are not fixed because they vary greatly according to the way in which the customer uses the VCR(VCP), and the environment in which the VCR(VCP) is used. But, in general home use, a good picture will be maintained if inspection and maintenance is made every 1,000 hours. The table below shows the relation between time used and inspection period. Table 1 When inspection is necessary
About 1 year
About 18 months
About 3 years
Average hours used per day
4. Supplies Required for Inspection and Maintence (1) (2) (3) (4)
Grease : Kanto G-311G (Blue) or equivalent Isopropyl Alcohol or equivalent Cleaning Patches Grease : Kanto G-381(Yellow)
5) Maintenance Procedure 5-1) Cleaning (1) Cleaning video head First use a cleaning tape. If the dirt on the head is too stubborn to remove by tape, use the cleaning patch. Coat the cleaning patch with Isopropyl Alcohol. Touch the cleaning patch to the head tip and gently turn the head(rotating cylinder) right and left. (Do not move the cleaning patch vertically. Make sure that only the buckskin on the cleaning patch comes into contact with the head. Otherwise, the head may be damaged.) Thoroughly dry the head. Then run the test tape. If lsopropyl Alcohol remains on the video head, the tape may be damaged when it comes into contact with the head surface. (2) Clean the tape transport system and drive system, etc, by wiping with a cleaning patch wetted with Isporopyl Alcohol.
NOTES:
One hour
1
Two hours
2
Three hours
It is the tape transport system which comes into contact with the running tape. The drive system consists of those parts which moves the tape. Make sure that during cleaning you do not touch the tape transport system with the tip of a screw driver and no that force is that would cause deforming or damage applied to the system.
Drum (Rotating Cylinder)
Cleaning Patch Head Tip
Coat With Isopropyl Alcohol
Touch this section of cleaning patch to the head tip and gently turn the Drum (Rotating Cylinder)
Fig. C-9-4 4-20
MAINTENANCE/INSPECTION PROCEDURE 5-2) Greasing (1) Greasing guidelines Apply grease, with a cleaning patch. Do not use excess grease. It may come into contact with the tape transport or drive system. Wipe any excess and clean with clean ing patch wetted in Isopropyl Alcohol.
(2) Periodic greasing Grease specified locations every 5,000 hours. 1) Loading Path Inside & Top side 2) Shaft 3) Gear Rack F/L Moving Section 4) Shaft
NOTE:Greasing Points 1) Loading Path Inside & Top side 2) Base Tension Boss inside Hole 3) Arm Assembly F/L "U" Groove 4) Arm Take-up Rubbing Section 5) L/D Motor Gear Wheel Part
5) Lever Tension Groove 6) Clutch Assembly D33 Shaft 7) Brake "S" Rubbing Section
2
6) Shaft 7) Arm Assembly F/L of Buming Inside Hole 8) Reel S, T Shaft (G381:Yellow) 9) Brake T Groove
1
2 3 8
4 1
3 4
5
7
6 5
Chassis (Bottom)
6
Chassis (Top) Gear Part
Gear Cam
Gear Sector
Guide Rack F/L
Gear Drive
Base Loading
Guide Rail
Bracket Side (L)
4-21
Bracket Assembly Door
Gear Rack F/L
GEAR , F/R
GEAR AY, P2 & P3
4-22
MECHANISM TROUBLESHOOTING GUIDE 1.Deck Mechanism A. Auto REW doesn't work.
YES Is the output of END sensor of supply side "H"? “H”: more than 3.5V “L”: less than 0.7V~1V
YES
NO Is the Vcc. voltage of End sensor 5V?
NO
Check the syscon power.
YES Replace End sensor.
Is the voltage across IR LED between 0.8~1.5V?
NO
Replace LED.
NO Check syscon circuit.
B. No F/R modes.
YES Is the present mode, F/R Mode?
NO
Is the mode SW assembled correctly (refer to Pages 4-14.)
YES NO Does the Capstan Motor rotate?
YES Do the T/Up, Supply Reel rotate?
YES Check syscon circuit.
4-23
Is the normal voltage supplied to the Capstan Motor Vcc1, Vcc2.?
YES Does terminal voltage(Vctl) of Capstan Motor supply side more than 4V?
YES Replace the Capstan Motor.
NO Check Servo, Power Circuits.
MECHANISM TROUBLESHOOTING GUIDE C. AUTO STOP. (PLAY/CUE/REV) Check aligment positions (page 414) Check spring Pinch. In Play/Cue/Rev is the pinch roller in contact with the capstan shaft.
NO Is the output of DFG, DPG OK?
YES Are there T/up and supply reel pulses.
Replace Drum Motor.
NO YES NO Check Servo, Syscon.
YES Check the Syscon, µ-COM.
Replace Reel Sensor.
D. No cassette loading.
Insert the cassette.
YES Does the lever Assembly S/W work normally.
NO Check Holder Assembly CST.
YES Is there variation for CST IN S/W Output? (In Tape with REC Tab “L”→“H”→“L”) (In Tape without REC Tab “L”→“H”→“L”→“H”)
NO
Does the CST IN S/W work normally?
NO Replace CST IN S/W.
YES YES NO Check Syscon Circuit.
Check Syscon Circuit.
4-24
MECHANISM TROUBLESHOOTING GUIDE E. In PB mode Tape Presence not sensed.
Is the Pinch Roller attached to the Capstan Motor Shaft?
NO
Check Alignment positions (page 4-14)
YES Does the T/Up Reel turn?
NO
NO Is the Belt ok?
YES
Replace the Belt.
YES Check the clutch and the Idler Assembly.
Does the Capstan Motor turn?
YES Does the Drum Motor turn?
NO
YES
Is the Voltage supplied to the Capstan Motor Vcc1,Vcc2 each?
YES
Are there DPG, DFG Pulses?
Is the terminal voltage of Capstan Motor supplied more than 4V?
YES
NO
Check Servo, Power.
YES
Are the T/Up Supply Reel Sensors ok?
Replace the Capstan Motor.
YES NO Check Servo, Syscon.
Is the Vcc voltage of the Drum Motor normal?
NO
Check Syscon, Circuit.
YES Is the terminal voltage of the Drum Motor more than 2.3V?
YES Replace the Drum Motor.
4-25
NO
Check Syscon, Circuit.
MECHANISM TROUBLESHOOTING GUIDE 2. Front Loading Mechanism A. Cassette cannot be inserted. Does the Lever Assembly Switch work?
NO
Is the Lever Assembly Switch Spring damaged or omitted?
YES YES
Does the CST IN Switch work normally?
Is the Vcc of Main P.C.Board 5V?
YES
Replace or add the Lever Assembly Switch Spring.
NO Replace CST IN Switch.
YES Check syscon circuit.
NO
Is the voltage between cassette switch and GND on Main P.C.Board 5V??
YES
NO
Check power circuit.
NO
Check Mode switch location and syscon circuit.
Is there a short circuit between cassette switch and GND on main P.C.Board?
NO
YES
Remove the short circuit part or Replace the main P.C.Board.
Replace CST IN Switch.
B. Cassette will not eject.
Does the L/D motor rotate in reverse?
NO
Check L/D Motor or Drive IC.
YES Does the Lever Assembly Switch work?
NO Replace lever Assembly Switch.
YES NO Does the Arm Assembly F/L work normally?
Replace Arm Assembly F/L.
YES NO Does the Opener Door work?
Replace the Opener Door.
4-26
MECHANISM TROUBLESHOOTING GUIDE C. Cassette will not load.
Does the CST insert?
YES Does the opener Lid work?
YES
NO
Does the Gear Assembly Rack F/L work?
YES
NO
Does the Opener Door work?
YES
Check the power of L/D Motor.
NO
Replace the Front Loading Mechanism Assembly.
4-27
Replace the Arm Assembly F/L.
NO
Does the Holder Assembly Cassette move the Arm Assembly F/L?
YES
Is the opener Door assembled correctly?
NO
Does the L/D Motor work?
YES
Replace the Gear Rack F/L.
NO
Does the Arm Assembly F/L work?
YES
Replace the Opener Lid.
Is the Holder Assembly Cassette assembled correctly?
EXPLODED VIEWS
1. Front Loading Mechanism Section
103 117
A24
110
116 115
105
100
117
112
106
107 102
A21
113
114
032
A23
054
054A
A22
109
4-28
EXPLODED VIEWS
2. Moving Mechanism Section(1)
031
079
001
402 002A
017
401
022
032
003
402 002
001
012
A01
024
004
405 023
008
406
006
A03
409
007
013
016
014
405 010
A04
015
009
019 018
025
026
027
029
028
020
030
021
4-29
EXPLODED VIEWS
3. Moving Mechanism Section(2)
518 055
058
051
060
056
052A
052
517
A11
078
061
410
067
066 065
077
076
064
A12
032
068
069
070
4-30
MEMO
VICTOR COMPANY OF JAPAN, LIMITED VIDEO DIVISION
S40894
Printed in Japan
BLOCK DIAGRAMS 1. Power Block Diagram
BD101
!
T101 ! TRANSFORMER
R101 4
2
6
SNUBBER BLOCK
1
+
3
7
C103
8 (D102,R104, C105,C106)
Q155
RECTIFIER & SMOOTHING
TO Canal+ 12VA
(D109, C120, L104,C121)
4 9
RECTIFIER & SMOOTHING 24V S/W Q159,R166,R167
(D110, C123)
TO CAPSTAN M 24/12VA
DRIVE & S/W BLOCK OVER CURRENT LIMIT BLOCK
R106 R102
LINE FILTER BLOCK
D155
(IC101, R109, C135, D103,
10
R103,C109, R125, R126)
(C101,L102, C102)
F. µ-com SEARCH "H"
Q161 R163
TO DRUM 12VA
RECTIFIER & SMOOTHING (D106, C116, L103,C117)
3
TO TU/IF 33V
11
! 2
RECTIFIER & SMOOTHING
12
F101
(D105, C115)
!
HOT GND
1 4
! C113
C112
FEED-BACK BLOCK
! 3 IC102
BK WH (BR) (BL) PW101
!
2
!
HOT CIRCUIT
TO SYS, TU/IF 5.4VA
36V S/W BLOCK (Q154, R157, R158,R155)
5VT SW BLOCK (Q152, R153, R154, D156)
TO AV, TU/IF,
5.2VT
5V S/W BLOCK (Q151, R151, R152)
(R116,R117,R118 R119,R120,R121 C114)
PWR CTL BLOCK
IC103
(Q162, R161)
Q163
TO Hi-Fi, Sensor SECAM 5.2V
FROM µ-COM P.CTL"H"
TIMER "H" FROM µ-COM
'00 11. 30
NOTES :
Symbol denotes AC ground. Symbol denotes DC chassis ground.
3-21
3-22
60 DATA 55 DAV
59 CLK
141 5.2VA
731
27
144
VPS BLOCK
2
1
SDA5650
IC7V1
13
14
60
VSUP
358 VPS V.out GND
94
12
(From Power)
T1
59
IIC BUS INTERFACE
3
4
5
6
7
DA VIN EHB
TIMING
DATA AQUISITION
8
875
9
5.2VT 143
DATA/SYNV SLICER CLOCK PLL
146
5.4VA 141
11 10
CSO
CVBS SCL
S.V.W 396
VC01
93
Iref SDA
144
VCS
3-24 PD2/ VC02
3-23 PD1
2. Tu/IF, NICAM & A2 Block Diagram 3. VPS Block Diagram
4. Y/C Block Diagram
5. Hi-Fi Block Diagram
65
63
61
Hi-Fi PNR Block
67
S1 V.OUT
68
S2 V.OUT
69
70
V.OUT (MICOM)
C.SYNC
78
CLOCK
79
C.ROTARY DATA
V.H.SW
(PB MODE)
60dB AMP PB FM AGC
MAIN DE EMP
SUB LPF
Y/C MIX
Y-LPF PB FM EQ V.ENV
FM OEM
84
46
YNR
IC301 LA71750M
87
Y-Delay
43
90 C-Delay (1H/2H)
BPF
CCD LPF
21 22
SYNC IN CNC
29
IC201 LA70100M 14
80
79
78
76
75
70
67
65
59
58
54
52
29
B
A
13
V.IN4 FRONT V.IN3 DEC
68
V.OUT MICOM
CLOCK
69
C SYNC
DATA
C.ROTARY
REC'H'
V.H.SW
16 17
IC801
(REC MODE)
37 36 35
18
25
Hi-Fi REC Block
21
Scart 2 Audio Out
ACC DET
Scart 1 Audio Out
96
19 20
MAIN CONV
ACC
33 32 31 30 29 28 27 26 25 24 23
C LPF 93
16
IC201 LA70100M NL EMPHA
SW AGC
W/D CLIP
V.IN2 S1
48
V.IN1 TUNER
2
12
DETAIL ENH Y-LPF
88
50
1 2 3 4 5 6 7 8 9 10
W/D CLIP
FBC
REC FM EQ
46
UP REC
IC301 LA71750M Killer
C-LPF
BPF 1H/2H DELAY Main Conv
ACC
Main Conv
COMP AMP
33
KILL DEC
32
REC APC VX02 21
27
28
VX02 31 29 CLK-IN
4.43MHz
3-25
3-26
Normal A.IN (From AVCP)
95
Normal A.out (To AVCP)
SP REC
Modulator A.out (To Tuner)
(To Drum)
43
Y-DELAY
• Tuner • F.A/V • Scart1 • Scart2
94
YNR
Audio input Block
89
(To Drum)
6. System Block Diagram
LD(+) LD(-)
IC501 HD6432197A L/M CONTROL R525, R526
RC501 RC501, R5R7 R5R7, R5R8 C5R, C5R2
2fsc R524, R514, R518, R516, R589, C577, C576, L501, Q504
3-27
3-28
CIRCUIT DIAGRAMS 1. Power Circuit Diagram D109, C120 are defective. No 14VA, 12VA are 12VT.
Power dead. BD101, R101 are defective. No power. D102 is defective.
No 5.3VA and 5VG, 5VT. D106 is defective. No 5.2VT. Q152 is defective.
Power dead. F101 is defective.
Switching dead. IC101 is defective.
Power dead. IC102, IC103 are defective.
NOTES)
Symbol denotes AC ground.
NOTES)
Symbol denotes DC chassis ground.
NOTE) NOTE) NOTE) NOTE)
Warning Parts that are shaded are critical With respect to risk of fire or electricial shock.
NOTE : 1. Shaded( ) parts are critical for safety. Replace only with specified part number. 2. Voltages are DC-measured with a digital voltmeter during TUNER mode.
3-29
3-30
2. Tuner, NICAM Circuit Diagram
FROM POWER
F.A/V -
F/To Hi-Fi F.A/V -
F. SYS
To A/V To Hi-Fi
EE MODE(VIDEO) TU MODE (AUDIO)
3-31
3-32
3. A/V, SECAM, VPS Circuit Diagram
IC301 Pin70 is defective. PB COLOR Signal disappear.
Q305 is defective. EE, PB Screen doesn’t appear.
D301or IC301 Pin 80 REC is defective.
9
3
6
1
2
2 2
IC301 Pin 84 is defective. Audio Tracking is failed. 14 10 7
IC301 Pin 69, 68 are defective. PB and Recording is failed. (IC301 doesn’t operate.)
F/To SYS
4
5 11
12
8 13
IC301 Pin 10 is defective. PB COLOR Signal disappear. IC301 is defective. PB COLOR Signal disappear.
Q302, Q303, Q314 are defective. No mono Audio Signal in PB MODE. PB Y+C
REC Y+C
REC AUDIO
PB Y
REC Y
PB AUDIO(MONO)
PB C
REC C
WAVEFORM
PB SECAM COLOR
REC SECAM COLOR
D301 or IC301 Pin30 is defective. REC is failded.
FL301, Q301, Q306 are defective. Normal Audio signal is not recorded.
3-33
3-34
4. System Circuit Diagram Reset is defective. Set dead. IC504 is defective.
CLOCK SETTING will not operate. X501 is defective.
µ-COM will not operate. X502 is defective.
LED DOT MODEL ONLY
REC/STANDBY TIMER VCR PWR 5 5 1 2 9 3 4
6
7
8
Remote control’s Pulse will not received. RC501 is defective. VCR will not operate. IC505 is defective.
Deck will not operate. R575, R576, R577, R578 are defective.
Auto stop occures. RS501,RS502,Q514, Q515 are defective.
Auto Rew will not working. ES501, ES502, LD501 are defective.
µ-COM is unstable. Q501, Q503 are defective.
WAVEFORM
3-35
3-36
WAVEFORM & VOLTAGE SHEET _ IC301 Oscilloscope Waveform
IC301 Pin 20 PB mode 500mvp-p
IC301 Pins 38,32,31 38, 38 Video in 1Vp-p
IC301 Pin 28 PB/REC mode 4.0Vp-p
IC301 Pin 7 REC mode 1.1Vp-p
IC301 Pin 6 REC mode 2.0Vp-p
IC301 Pin 29 PB mode 2.02Vp-p
IC301 Pin 41 PB mode 400mVp-p
IC301 Pin 64 PB mode 400mVp-p
IC301 Pin 23 PB/REC mode 5Vp-p
IC301 Pin 24 PB/REC mode 5Vp-p
IC301 Pins 71 72 REC mode 340mVp-p
IC301 Pins 51 54 PB mode 300mVp-p
IC301 Pin 63 PB mode 400mVp-p
IC301 Pin 11 PB mode 3.6Vp-p
3-37
* IC501 Waveform Photographs
V.HSW (IC501 Pin 105) 1V/10mS REC/PB MODE
DV.SYNC (IC501 PIN 109) 1V/100uS QUE/REV MODE
CTL(+) (IC501 Pin 3) 1V/10mS
CTL(-) (IC501 Pin4) 1V/10mS
DFG/FG (IC501 PIN 103,104) 1V/10mS REC/PB MODE
CFG (IC501 Pin9) 1V/10mS
V.IN (IC501 Pin 17) 500mV/20uS
V.OUT (IC501 Pin 19) 500mV/20uS EE/PB MODE
C.SYNC (IC501 Pin 111) 1.0V/100uS EE/PB MODE
3-38
5. Hi-Fi, SCART Circuit Diagram IC801 42, 43 Pins are defective. All Audio is not appear.
F. PWR F/To A/V F/To PWR F/To SYS F/To A/V
F/SYS
F/SYS
F/SYS
F/To A/V
F/To A/V
F/To SYS
F/To Tuner
F/To A/V
- To STS or SYSTEM
- F. POWER
NORMAL Audio
V.IN
F. SYS
V.OUT
F. SYS
PB Hi-Fi
F. PWR
F. SYS
3-39
3-40
• CIRCUIT VOLTAGE CHART MODE PIN NO.
EE
REC
MODE PIN NO.
EE
PB
REC
MODE PIN NO.
EE
PB
REC
R
2.45
2.45
11
2.41
2.41
2.42
47
4.17
4.17
4.17
2.44
12
2.1
2.1
2.08
48
2.35
2.37
A
-0.03
K
4.05
-0.03
0
13
0
5..29
5.29
49
3.18
4.06
4.07
14
5.26
5.26
5.25
50
1.97
15
0
0
0
51
PB
IC103
IC201
MODE PIN NO.
EE
MODE PIN NO.
EE
PB
REC
MODE PIN NO.
2.33
1
0
0
0
55
5.27
5.29
0.08
110
0
56
5.27
5.28
5.28
111
4.2
3.18
3.18
2
2.39
2.57
1.97
1.97
3
2.57
2.57
2.57
57
0
0
0
112
5.29
5.28
3.04
58
0
0
0
0
0
0
4
2.57
2.57
2.1
59
4.91
4.92
4.79
1
0
0
PB
REC
IC501
EE
REC
MODE PIN NO.
0
0
0.4
0.4 5.27
PB
EE
PB
20
2.6
2.63
2.5
21
2.57
2.59
2.47
22
2.66
2.86
2.55
23
2.63
2.64
2.51
0
24
2.5
2.5
2.39
IC503
REC
1
2.52
2.52
2.52
16
0
0
0
52
1.97
1.97
1.97
5
2.57
2.57
2.57
60
4.91
4.91
4.79
2
0
0
0
25
2.52
2.53
2.4
2
2.4
2.41
2.41
17
0
0
0
53
2.34
2.35
2.35
6
2.56
2.57
2.57
61
5.17
5.18
5.18
3
0
0
0
26
2.36
2.37
2.27
3
0
3.35
3.37
18
0
0
0
54
1.97
1.99
1.99
7
2.58
2.59
2.58
62
5.17
5.19
5.18
4
0
0
0
27
0.01
0
0
4
0
2.59
0
31
55
5.24
5.24
5.24
8
2.55
2.55
2.55
63
2.84
2.83
2.86
5
5.01
4.95
4.79
28
2.51
2.47
2.41
2.6
2.57
2.46
IC301
5
0
0
0
1
5.15
5.14
1.7
56
2.25
2.31
2.29
9
4.62
2.31
2.31
64
5.14
5.14
5.15
6
5.01
4.95
4.8
29
6
2.8
3.72
0
2
0.02
0.03
0.75
57
2.02
2.14
1.99
10
4.85
5.16
5.016
65
0.01
0.01
0.02
7
0
0
0
30
7
0
0
0
3
2.29
2.29
0
58
2.37
2.4
11
1.89
1.91
1.9
66
5.1
5.11
5.11
8
5.29
5.29
5.28
31
2.34
2.41
1.38
8
0
0
0
4
1.46
0.5
59
2.94
2.95
2.93
12
1.89
1.9
1.89
67
0.83
0.83
0.89
32
0.03
0.02
-0.07
9
3.04
3.02
3.04
5
2.28
2.26
2.47
60
1.42
1.55
1.38
13
2.61
2.5
2.49
68
0.01
5.3
5.3
1
5.28
5.28
5.28
33
0.03
0.04
-0.06
10
2.53
2.51
0
6
2.29
2.28
2.29
61
1.72
1.85
2.05
14
0.4
0.4
0.4
69
0.01
5.3
5.3
2
0
0
0
34
12.6
12.5
12.57
0.11
15
0.08
0.1
0.56
70
5.29
5.3
5.3
3
5.28
5.28
5.28
35
3.35
3.31
2.89
16
1.99
1.91
1.98
71
5.29
0
0.01
36
3.29
3.3
2.9
IC504
11
2.1
2.08
2.19
7
2.28
2.28
2.27
62
0.09
0.11
12
3.32
1.96
3.25
8
2.27
2.27
2.27
63
1.75
1.84
13
4.01
4.01
4.01
9
2.26
2.26
3.05
64
0
0
0.
17
2.39
2.34
2.31
72
0.03
0.03
0.04
1
5.28
5.28
5.28
37
3.29
3.3
2.9
14
2.55
2.54
2.56
10
2.29
2.29
2.28
65
1.85
1.85
1.81
18
5.14
5.14
5.11
73
5.24
5.23
5.22
2
0
0
0
38
3.55
3.56
3.42
15
3.06
1.94
3.06
11
2.37
2.39
2.28
66
0
0
0
19
2.41
2.37
2.33
74
0
0
0
3
4.87
4.87
4.87
39
0
0
0.01
16
6.2
3.2
3.22
12
0
0.02
0.11
67
0.
0.44
0.4
20
0
0
0
75
1.49
1.5
1.5
40
5.2
5.2
5.21
17
2.34
4.25
0.22
13
2.26
2.3
2.28
68
4.79
4.91
4.81
21
2.47
2.47
0
76
1.3
1.4
1.21
1
0
0
0
41
2.27
2.29
2.5
18
0.13
3.44
0.13
14
69
4.75
4.81
4.79
22
2.46
2.46
0
77
5.27
5.27
5.27
2
5.01
4.94
4.79
42
4.96
4.98
4.91
19
2.23
2.21
2.22
15
2.26
2.26
2.29
70
5.27
2.69
2.69
23
0
0
0
78
2.55
2.53
2.54
3
5.01
4.94
4.78
43
5.05
5.06
4.97
20
2.08
2.22
2.06
16
5.17
0.16
5.05
71
0.01
0
0.01
24
0.51
2.47
0.01
79
0
0
0
4
0
0
0
44
2.8
2.79
2.69
21
2.27
2.4
2.28
17
2.26
2.26
2.27
72
5.13
5.11
5.09
25
2.81
2.88
2.8
80
5.29
2.58
2.58
5
5.28
5.28
0.39
22
1.42
1.43
0
18
5.17
5.17
5.14
73
1.98
2.21
26
5.27
2.28
5.28
81
3.25
3.25
3.25
6
5.28
5.28
1
5.14
5.15
5.15
23
5.05
5.02
5.06
19
4.24
4.25
3.07
74
2.55
2.63
2.53
27
2.46
2.5
2.54
82
5.28
5.28
5.28
7
0
0
2.66
2
1.51
1.51
1.51
24
5.05
5.02
5.06
20
0
0
0
75
2.46
2.63
2.45
28
5.27
5.28
5.28
83
0
2.7
2.69
8
0
0
0
3
1.51
1.51
1.51
25
2.31
2.07
2.37
21
3.36
1.96
3.25
76
2.47
0.77
2.45
29
5.22
5.27
5.27
84
0
2.77
2.77
9
0.01
0.01
2.31
4
0
0
0
26
2.3
2.02
2.38
22
3.07
3.06
3.06
77
1.59
1.59
1.49
30
0
5.01
0.05
85
0
3.55
3.55
10
0
0
2.36
5
2.47
2.48
2.48
27
2.09
2.08
2.11
23
3.06
3.03
3.05
78
2.7
3.39
2.69
31
0.17
1.9
86
2.65
2.68
2.86
11
0.01
0
2.31
6
2.47
2.48
2.48
28
0.18
0.19
0.18
24
5.16
5.16
5.13
79
2.02
1.91
2.52
32
0.12
87
0
3.3
3.21
12
1.56
1.56
1.56
7
0.54
0.5
0.46
29
0.48
0.26
0.41
25
0.13
3.44
5.13
80
1.06
1.06
4.72
33
0.18
0.18
0.18
88
0
0
0
13
0.99
0.99
1.39
8
0
0
0.45
30
2.08
2.07
2.11
26
1.44
1.82
0
81
1.11
1.12
1.11
34
0.31
0.3
0.43
89
0
0
0
14
5.28
5.29
5.28
9
0
0
0.45
27
2.07
2.1
1.42
82
0
0
0
35
5.27
5.28
5.28
90
0
0
0
10
0
0
0
0
IC401
0.02
IC7V1
IC801
IC751
1
2.84
2.91
2.7
11
5.16
5.16
5.16
2
2.92
2.91
2.81
12
4.91
4.86
4.79
3
2.91
2.9
2.81
13
4.9
4.8
4.79
0
4
2.82
2.81
2.68
14
2.58
0.51
0.57
0.1
0.07
5
2.8
2.86
2.67
15
2.58
0.5
0
0
0
6
2.8
2..86
2.66
16
2.41
0.51
0.57
0
0
7
2.79
2.85
2.65
17
0.53
0.53
0
5.26
5.25
8
2.78
2.85
2.65
18
0.54
0.51
0.58
0
9
2.79
2.84
2.66
19
5.13
5.14
5.14
0
10
2.79
2.84
2.66
20
0
0
0
0.13
0.57
11
2.77
2.83
2.65
21
0.53
0.51
0
0
0
0
12
2.76
2.82
2.64
22
5.16
5.16
5.16
103
0.12
1.39
1.39
13
2.71
2.75
2.59
23
0
0.02
0
104
0.12
1.39
1.39
14
2.49
2.51
2.33
24
0
0.02
0
0
105
0
2.7
0
15
2.48
2.51
2.32
25
0
0
0
0.04
0.02
106
0
2.64
5.12
16
2.64
2.67
2.49
26
0
0.05
0
5.28
5.29
5.29
107
0
2.75
2.74
17
2.64
2.68
2.5
27
0.05
0.05
0
53
0
0
0
108
0
2.78
2.77
18
1.48
2.57
2.32
28
0
0
0
54
5.25
5.26
5.27
109
0.05
0.05
0.05
19
2.63
2.67
2.5
29
0
0
2.8
1
0
0.01
0
28
4.23
4.21
4.18
83
5.13
1.47
1.51
36
5.28
5.29
5.28
91
0
0
2
5.21
5.2
5.21
29
2.83
2.83
2.9
84
0.46
2.43
1.75
37
4.93
4.94
4.94
92
0.95
5.16
3
2.19
2.2
2.19
30
0
0
0
85
0
0
1.36
38
4.88
4.88
4.87
93
0
0
0
4
0
0
0
31
4.7
4.7
4.69
86
0
2.03
39
2.29
2.29
2.28
94
0
0
5
2.91
2.91
2.91
32
4.7
4.7
4.69
87
0
0.72
0.7
40
0
0
0
95
0.29
6
0
0
0
33
2.85
2.06
2.07
88
0.71
0.72
0.7
41
0
0
0
96
0
7
2.92
2.92
2.92
34
0.33
0.31
0.31
89
0.71
0.72
0.7
42
0
0
0
97
0
8
0
0
0
35
2.17
2.16
2.16
90
0.71
0.72
0.7
43
4.88
4.88
4.87
98
5.26
36
3.35
3.35
3.35
91
5.17
5.16
5.11
44
5.24
5.25
5.24
99
0
2.7
1
0
0
0
37
2.09
2.11
2.09
92
0
0
0
45
0
0
0
100
0.01
0
2
2.86
2.86
2.85
38
1.99
2.03
2.02
93
1.95
1.93
0.73
46
0
0
0
101
0.7
3
5.15
5.16
0
39
9.45
9.43
9.39
94
1.95
1.93
0.72
47
0
0
0
102
4
5.29
5.29
5.29
40
0
0
0
95
1.95
1.93
0.72
48
0
0
0
5
4.94
4.94
4.94
41
0
0
0
96
1.95
1.93
4.33
49
0.01
5.28
6
5.29
5.29
5.29
42
5.17
5.16
5.14
97
0
0
0
50
5.25
0
7
5.29
5.2
5.29
43
2.4
2.42
2.39
98
2.29
2.29
2.4
51
4.48
8
2.57
2.57
2.57
44
2.34
4.42
0.08
99
0
2.29
2.4
52
9
0
0
0
45
2.33
2.46
2.46
100
2.29
2.29
2.53
10
5.29
5.29
5.29
46
2.69
2.67
2.68
IC402
IC505
3-41
3-42
MODE PIN NO.
EE
PB
REC
Transistor
EE
EE Mode PB
REC
EE
PB Mode PB
REC
EE
REC Mode PB
REC
30
2.8
2.8
2.8
Q151
4.55
5.3
5.24
5.34
4.54
5.24
5.3
4.55
5.24
31
2.79
2.79
2.79
Q152
5.31
4.52
5.22
5.31
4.52
5.22
5.3
4.51
5.22
32
0
0.02
0
Q154
32.99
32.34
32.97
33.53
32.89
33.5
33.76
33.12
33.72
33
5.16
5.14
5.15
Q155
12.73
13.4
14.05
12.68
13.35
13.77
12.76
13.42
13.98
34
4.2
4.2
4.21
Q157
0.03
0.84
4.38
0.03
0.84
4.38
-0.03
0.84
4.38
35
0
0
0
Q159
29.84
29.78
13.21
29.79
29.8
12.48
30.14
30.13
12.73
36
2.8
2.8
30.11
2.8
Q161
0.03
0
29.82
0.03
0
29.8
-0.03
0
37
0
Q162
0.02
0.69
0
-0.02
0.69
0
-0.02
0.69
0
38
0
Q163
0.03
5.18
0.03
0.03
5.18
0.03
-0.03
5.18
0.03
0
Q164
-0.03
4.38
-0.01
-0.03
4.38
-0.01
-0.03
4.38
0
40
2.84
2.84
2.79
Q165
14.06
-0.01
14.04
13.74
-0.01
13.71
13.95
-0.01
13.95
41
2.85
2.83
2.79
Q166
4.4
5.3
5.11
5.3
4.41
5.13
5.3
4.4
5.1
42
2.59
2.59
2.59
Q301
0
0.01
5.15
0
0
5.15
0
0.75
1.69
43
2.31
2.31
2.3
Q302
5.18
5.18
-0.42
5.18
4.52
5.12
5.14
5.13
-24.71
44
3.3
0
Q303
0.01
-0.42
0
0
0.69
0.01
-18.22
-24.85
0.01
Q304
0.01
-0.4
0
0
0.71
0
-18.22
-24.7
0
Q305
2.01
1.29
0
2.53
1.83
0
2.5
1.81
0
Q306
5.14
5.19
5.19
5.19
5.16
5.19
1.9
2.14
4.89
Q307
2.69
1.98
0
2.69
1.98
0
2.64
1.93
0
Q308
2.66
1.98
0
2.63
1.96
0
2.6
1.93
0
Q309
3.09
2.41
0
3.05
2.37
0
3.01
2.33
0
Q501
0
0.67
0.01
0
0.67
0.01
0
0.67
0.01
Q502
0
0.71
0.01
0
0.22
2.33
0
0.23
2.29
Q503
5.3
4.61
5.28
5.3
4.61
5.28
5.3
4.61
5.28
Q504
0
0.14
2.69
0.05
0.63
2.65
0.05
0.67
2.67
Q5S1
0.43
0
1.61
2.22
0
2.53
1.92
0
2.5
Q514
0
5.09
0.01
0
Q515
0
0
5.16
0
Q906
0
0.12
1.93
0
0.07
2.37
0
0.13
2.4
Q901
0
5.26
0.01
0
5.25
0.01
0
5.25
0.01
39
0 0
Q7S1
0
0
1.32
0
0
0
0
0.98
Q902
12.73
0.01
12.73
12.66
0.01
12.66
12.72
0.01
12.71
Q903
0
0
12.72
0
0
12.64
0
0
12.71
3-43
3-44
PRINTED CIRCUIT BOARD DIAGRAMS 1. MAIN P.C.Board
LOCATION GUIDE
(Solder Side)
3-45
3-46
SECTION 5 REPLACEMENT PARTS LIST SAFETY PRECAUTION Parts identified by the ! symbol are critical for safety. Replace only with specified part numbers. 5.1
EXPLODED VIEW 5.1.1 PACKING AND ACCESSORY ASSEMBLY The instruction manual to be provided with this product will differ according to the destination.
OPTIONAL PARTS 806
811 810 812
CABLE SET ASS'Y (Optional parts)
PLUG ASS'Y 1WAY (Optional parts)
PLUG ASS'Y 2WAY (Optional parts)
821
801 808
BATTERY
803
PACKING (LF)
SCART CABLE
INSTRUCTION MANUAL
804
BAG. SOFR SHEET
803
802
PACKING (RF)
BOX CARTON 900
REMOCON
5-1
5.1.2 FINAL ASSEMBLY
BEWARE OF BOGUS PARTS Parts that do not meet specifications may cause trouble in regard to safety and performance. We recommend that genuine JVC parts be used.
457 464
452
A00
2SCART
320
452
452
462
1SCART
TU70
1(TU NER )
323
250
275
462 LED502(LED501)
300 A46
260
A42
283 284 281
A49
280 277
A43
330 OPTIONAL PARTS
5-2
452
5.1.3 MECHANISM ASSEMBLY 401
[ TOP VIEW ] 402
402
A04
008
002
025
405 010
A01
001
A03
006
002A
026 007 015 004
027 014
030
013 003 405
009
409
029
016
023
022 011
012 031
017 019 018
079
028 021 020
032 024 406
A22 054 109
103
106
117 105
117
054A
A21
[ BOTTOM VIEW ]
107 051
A11
102
100
067
066
052
065
110 112
113
114
A12
517
A23
061
A24
068
064
056 069 058
116 115
078
518
070
077
052A
055
076
032
060
410
5-3
5.2 # REF No.
MODEL HR-J285EU HR-J290EU HR-J585EU HR-J590EU HR-J593EU
REPLACEMENT PARTS LIST PART No.
PART NAME, DESCRIPTION
SPECIFICATION
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
****************************** PACKING AND ACCESSORY ASSEMBLY 801 801 801 801 801 801 801 801 801 801 801 802 803 804 804 806 808 810 821 900 900 900
LG-3835RP0075B LG-3835RP0075C LG-3835RP0075D LG-3835RP0075E LG-3835RP0075F LG-3835RP0075G LG-3835RP0075H LG-3835RP0075K LG-3835RP0075L LG-3835RP0075M LG-3835RP0075N LG-3890R-H768D LG-3920R-0067A LG-292-053A LG-3880R-H001A LG-6850R-CAA26 — LG-6851RP0003A LG-6850R-SMA21 LG-6711R1P037A LG-6711R1P037B LG-6711R1P037C
INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY BOX PACKING BAG BAG CABLE,COAXIAL BATTERY,MANGANESE CABLE ASSY,RF CABLE,COAXIAL REMOTE CONTROLLER ASSEMBLY REMOTE CONTROLLER ASSEMBLY REMOTE CONTROLLER ASSEMBLY
(EN,GE,FR,IT,DU) (PT,GR,SP) (SW,DA,FI,NO,GE) (EN,GE,FR,IT,DU) (PT,GR,SP) (SW,DA,FI,NO,GE) (FR) (EN) (PO,CZ,HU) (EN) (PO,CZ,HU) EDJ200P NA3GJJX SW3-A 0.858 4 AF999NS 0.02 65 EPS 12 1190 23 SOFT(VCP) HDPE 500 500 0.03 VCR MIDI 1200M/M PAL-PAL DOUBLE SHIELD AAAM(R03) SEOTONG 1-5 V - 1PA CABLE ASSY,RF/SCART/RCA USING 14PIN 1200M/M SCART-SCART DOUB N5 NOR EDJ209P NA3GJJX JVC W/S N5 EDJ200P NAEGJJX JVC W/O SHO N5 EDJ209P NA6NJJY JVC W/SHOWV
AC AC AC B DE B DE B DE
J J J FG I KM H
LN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCD FG K E H I J LMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN FG B D FGHI L N AC KM E J
****************************** FINAL ASSEMBLY A00 A00 A00 A43 A43 A43 A43 A43 A43 A43 A43 A43 A43 A43 A43 A43 A43 A46 A46 A46 A46 A46 A46 A46 A46 A46 A46 250 250 260 280 280 283 283 283 283 284 ! 300 ! 300 320 320 320 320 323 330 452 457 462
LG-6721RF0700D LG-6721RF0710D LG-6721RF0750D LG-3721R-F253A LG-3721R-F253B LG-3721R-F253C LG-3721R-F253D LG-3721R-F253E LG-3721R-F253F LG-3721R-F253G LG-3721R-F253H LG-3721R-F253J LG-3721R-F253K LG-3721R-F253L LG-3721R-F253M LG-3721R-F253N LG-3721R-F253Q LG-3501R-5739A LG-3501R-5739B LG-3501R-5739C LG-3501R-5739D LG-3501R-5739E LG-3501R-5739F LG-3501R-5739G LG-3501R-5739H LG-3501R-5739J LG-3501R-5739K LG-3110R-0128C LG-3110R-0223G LG-3210R-0023B LG-3720R-F193A LG-3720R-F193B LG-3580R-V031A LG-3580R-V031B LG-3580R-V031C LG-3580R-V031D LG-442-681A LG-6410RBHV01A LG-6410RCHP03B LG-3720R-D020A LG-3720R-D020B LG-3720R-D020C LG-3720R-D020D LG-3111R-0089C LG-3550R-0210A LG-353-051A LG-353-051E LG-353-136A
DECK ASSEMBLY,VIDEO DECK ASSEMBLY,VIDEO DECK ASSEMBLY,VIDEO PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT PANEL ASSEMBLY,FRONT BOARD ASSEMBLY BOARD ASSEMBLY BOARD ASSEMBLY BOARD ASSEMBLY BOARD ASSEMBLY BOARD ASSEMBLY BOARD ASSEMBLY BOARD ASSEMBLY BOARD ASSEMBLY BOARD ASSEMBLY CASE CASE FRAME PANEL,VIDEO PANEL,VIDEO DOOR,CASE DOOR,CASE DOOR,CASE DOOR,CASE SPRING POWER CORD POWER CORD PANEL PANEL PANEL PANEL CASE ASSEMBLY COVER SCREW SCREW SCREW
D35(N) DI(2HD, SP ONLY, AHC(X) D35(N) DI (2HD, NP, AHC(X), B/ D35(N) DI (4HF, PAL, AHC(X), B EDJ200P (J285EU) EDJ209P (J290EU) EDJ904NS (J595MS) EDJ900NP (J585EU) EDJ209P (J293EU) EDJ909NP (J590EU) EDJ909NP (J593EU) EDJ204S (J295MS) EDJ904NI(J595EK) EDJ200Y (J282EU) EDJ203Y (J283EU) EDJ203NI (J295EK) EDJ903NY (J583EU) EDJ900NY (J582EU) JVC DI EC(D) SERIES JVC DI EC(D) SERIES JVC DI EC(D) SERIES JVC DI EC(D) SERIES JVC DI EC(D) SERIES JVC DI EC(D) SERIES JVC DI EC(D) SERIES JVC DI EC(D) SERIES JVC DI EC(D) SERIES JVC DI EC(D) SERIES TOP(Q280G:B/K),SIDE TOP( 0128 A288G SIDE SCREW 4EA MAIN (VII-PJT, 60HR) FRONT(B589G-SLVER) FRONT (Q280G) CST (VCR) (MONO-B589G-SILVER) CST (VCR) (MONO-Q280G-B.K) CST (VCR) (HIFI-B589G-SILVER) CST (VCR) (HIFI-Q280G-BK) DOOR H03VVH2-F2 X 0.75MM FILTER VOL HIT-102/H03VVH2-F (NM) HARNESS DISTRIBUTOR (PAL-1SCART) DISTRIBUTOR (PAL-SCART MONO) DISTRIBUTOR (PAL-2SCART HI-FI) DISTRIBUTOR (PAL-1SCART HI-FI) PRE-AMP (02-PAL) BOTTOM(LARGE) SPECIAL SPECIAL (3X12) SPECIAL(FBK) (353S353A)
AB
G JKL I CDEF H MN
A B F C J D E G H K L I N M B
J
A F C DE G MN H KL I E J ABCD FGHI KLMN ABCDEFGHI JKLMN ABCD FGHI KLMN E J AB G I KL J CD F H MN E ABCDEFGHI JKLMN HI ABCDEFG JKLMN A I KL B G J DEF H C MN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN
****************************** MECHANISM ASSEMBLY A01LG-6723R-0401A DRUM(CIRC) ASSEMBLY
5-4
D35-2CH SP ONLY (8P2)
AB
G JKL
# REF No.
MARK A B C D E
PART No.
MODEL HR-J595MS HR-J295MS HR-J595EK HR-J295EK HR-J293EU
MARK F G H I J
PART NAME, DESCRIPTION
MODEL HR-J282EU HR-J283EU HR-J582EU HR-J583EU
SPECIFICATION
MARK K L M N
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
A01 A01 A04 A04 A11 A12 A21 A22 A23 A24 001 001 001 002 002A 003 004 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 051 052 052A 054 054A 055 056 058 060 061 064 065 066 067 068 069 070 076 077 078 079 100 102 103 105 106 107 109 110 112 113 114 115 116 117 401 402 405 406 409 410 517 518
LG-6723R-0401B LG-6723R-0403C LG-4421R-0008A LG-4811RF0038A LG-4471R-0005A LG-4471R-0004A LG-4931R-0047A LG-4471R-0006A LG-4261R-0023A LG-4510R-0046A LG-6723R-0304A LG-6723R-0304B LG-6723R-0306C LG-4680R-B005A LG-5202R00002C LG-4930R-0284A LG-5006R-0034A LG-6850R-HG18Z LG-4260R-0038A LG-4810R-0125A LG-4261R-0022A LG-3041R-0037A LG-3041R-0038A LG-3041R-0039A LG-5870R-0005A LG-3041R-0036A LG-4408R-0003A LG-4970R-0140A LG-4421R-0008A LG-4970R-0128A LG-4421R-0006A LG-6520D00002A LG-3040R-0057A LG-4261R-0029A LG-4810R-0118A LG-4680R-D002A LG-4470R-0093A LG-4408R-0004A LG-4261R-0019A LG-4510R-0043A LG-4970R-0123A LG-3141R-0040A LG-4400R-0005A LG-4680R-A007A LG-4980R-0023A LG-4470R-0100A LG-4970R-0124B LG-4470R-0097A LG-4470R-0096A LG-4421R-0007A LG-4510R-0040A LG-4265R-0006A LG-4470R-0098A LG-4261R-0021A LG-4970R-0122A LG-4470R-0095A LG-4470R-0094A LG-4970R-0122A LG-4261R-0020A LG-4510R-0047A LG-3300R-M116A LG-4510R-0041A LG-3040R-0056A LG-3301R-M022A LG-4970R-0130A LG-4930R-0276A LG-4930R-0274A LG-4930R-0275A LG-4510R-0044A LG-5870R-0004A LG-4260R-0035A LG-3070R-0002A LG-4970R-0127A LG-4260R-0036A LG-4510R-0042A LG-4970R-0138A LG-3300R-M137A LG-1MEC0261518 LG-1MPC0261418 LG-1SZZR-0031B LG-1MEC0302018 LG-1SZZR-0032B LG-1APF0262218 LG-1WZZR-0004D LG-1WZZR-0004A
DRUM(CIRC) ASSEMBLY DRUM(CIRC) ASSEMBLY BRAKE ASSEMBLY BRACKET ASSEMBLY GEAR ASSY GEAR ASSY HOLDER ASSY GEAR ASSY ARM ASSY LEVER DRUM(CIRC) ASSEMBLY DRUM(CIRC) ASSEMBLY DRUM(CIRC) ASSEMBLY MOTOR(MECH) BRUSH,CARBON HOLDER,SHELF CAP CABLE,FLAT ARM BRACKET ARM ASSY BASE ASSY BASE ASSY BASE ASSY OPENER BASE ASSEMBLY REEL SPRING BRAKE ASSEMBLY SPRING BRAKE ASSY HEAD(CIRC) BASE ARM ASSEMBLY BRACKET MOTOR(MECH) GEAR REEL ARM ASSY LEVER SPRING CHASSIS ASSY BELT MOTOR(MECH) SUPPORTER GEAR SPRING GEAR GEAR BRAKE ASSY LEVER CLUTCH ASSEMBLY GEAR ARM ASSY SPRING GEAR GEAR SPRING ARM ASSY LEVER PLATE LEVER BASE PLATE ASSEMBLY SPRING HOLDER,SHELF HOLDER,SHELF HOLDER,SHELF LEVER OPENER ARM BODY SPRING ARM LEVER SPRING PLATE SCREW MACHINE,PAN HEAD SPR W SCREW MACHINE,PAN HEAD SCREW,DRAWING PAN HEAD MACHINE SCREW S/W + SCREW,DRAWING SCREW TAP TITE(B),PAN HEAD WASHER WASHER
D35-2CH SP/EP (8M2) D35-6CH PAL (8P6C) RS L/D(S) P3 P2 CST RACK F/L F/L ASSY SWITCH SUB D35-2CH (8P2) SUB D35-2CH (8M2) SUB D35-6CH (8P6C) DRUM I2OAL05 SEJIN-SANKYO ICLE ASSY D33 (TIP+2 SPRING) 1.4, FPC(6CH) FPC P=1.25 FFC UL2896(0.05X0.8) 7 T/UP(D35) CHASSIS TENSION(D35) P2 P3 P4 LID(D35) A/C HEAD (ALPS) S COIL RS D35 RS COIL D35 (TB) T D35 FE ST FE HEAD LOADING IDLER (N) L/D(S) LOADING MDB2B66 SANKYO D35 ASP WHEEL T PINCH T/UP COIL TENSION(D35) D35 CAPSTAN CAPSTAN F2QVB06 SANKYO D35 ASR CAPSTAN(D35) RACK F/L COIL D35 (RACK F/L) DRIVE(D35) CAM(D35) CAPSTAN F/R(D35) D35 (N) SECTOR(D35) P3 COIL D35 P3 P2 COIL D35 P2 SPRING SLIDER TENSION TENSION(D35) TOP COIL D35 (STOPPER) SIDE(L) CST SIDE(R) STOPPER DOOR F/L(L) F/L COIL D35 (F/L(R)) F/L(R) SWITCH COIL D35 SWITCH SPRING CST D2.6 L4.5 MSWR3/FZY D2.6 L4.0 MSWR3/FZY D2.6 L5.8 SWRCH16A/FZY TAP D3.0 L6.0 MSWR3/FZY D2.6 L5.0 SWRCH18A/FZY TAP D2.6 L6.8 MSWR3/FZY STOPPER STOPPER
I CDEF H MN AB G JKL ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN AB G JKL I CDEF H MN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN CDEF H I MN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGH JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN
MODEL HR-J285EU HR-J290EU HR-J585EU HR-J590EU HR-J593EU
# REF No.
PART No.
PART NAME, DESCRIPTION
SPECIFICATION
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
# REF No.
MAIN BOARD ASSEMBLY LG-6871R-5739A PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739B PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739C PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739D PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739E PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739F PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739G PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739H PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739J PWB(PCB) ASSEMBLY,TOTAL LG-6871R-5739K PWB(PCB) ASSEMBLY,TOTAL STR-A6351 IC,POWER MANAGEMENT LTV-817B SENSOR LG-0IKE431000A IC,KEC LG-0ILNRSA007A IC,LINEAR LG-0ILNRSA005A IC,LINEAR LG-0IMCRHI014B IC,MICRO CONTROLLER LG-0IMCRHI019A IC,MICRO CONTROLLER LG-0IAL241600B IC,ATMEL LG-0IKE703100A IC,KEC LG-0IKE704200B IC,KEC LG-0IIT341700B IC,ITT LG-0ILNRMN001A IC,LINEAR LG-0IPH960500A IC,PHILIPS MM1443XJ IC,MITSUMI LG-0TR127309AA TRANSISTOR LG-0TR127309AA TRANSISTOR LG-0TR126809BA TRANSISTOR,BIPOLARS LG-0TR320509AB TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR120109AC TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR220309AF TRANSISTOR LG-0TR127309AA TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR198009CA TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR198009CA TRANSISTOR LG-0TR534409AA TRANSISTOR LG-0TR198009CA TRANSISTOR LG-0TR198009CA TRANSISTOR LG-0TR198009CA TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR127309AA TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR534309BA TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR220309AF TRANSISTOR LG-0TR120309AE TRANSISTOR LG-0TR534309BA TRANSISTOR S1WBA60 DIODE EG01CW DIODE,RECTIFIER LG-0DR180209AA DIODE,RECTIFIER 1SS133DIODE,SWITCHING LG-0DR104009BA DIODE,RECTIFIER 1N5822DIODE,RECTIFIER LG-0DR202000AB DIODE,RECTIFIER LG-0DR104009AB DIODE,RECTIFIER 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING 1SS133 DIODE,SWITCHING MTZ13CT-77 DIODE,ZENERS
EDJ209P (PCB ASSY) EDJ200P (PCB ASSY) EDJ904NS (PCB ASSY) EDJ900NP (PCB ASSY) EDJ909NP (PCB ASSY) EC(D) SERIES (PCB ASSY) EDJ SERIES (HIFI) EDJ904NI (HIFI) EDJ SERIES (MONO) EDJ203I (MONO) STR-A6351 SANKEN 8 DIP ST SMPS LTV-817B,PHOTO COUPLER(LITEON) KIA431 3 PIN TP LA70100M SANYO 30 SOP ST SECAM LA71750AM SANYO 100 QFP TRAY A HD6432197SA06F HITACHI 112 QFP HD6432197SA09F HITACHI 112P QF AT24C16 - - - KIA7031P 3P 3.1V RESET(TAPING) KIA7042P 3P 4.2V RESET(TAPING) MSP3417D-QG QFP44 BK NICAM+A2 SDA5650 MICRONAS 14 DIP ST VPS TDA9605H QFP44 BK HIFI AMP+HIF MM1443XJ SSOP-34 TP CANAL S/W KTA1273-TP-Y (KTA966A)KEC KTA1273-TP-Y (KTA966A)KEC KTA1268-BL TP KEC KTC3205-TP-Y (KTC2236A)KEC SRC1203 TP AUK TO92 22K,22K 2SC5343-L TP AUK TO92 SRC1201 TP AUK TO92 4.7K,4.7K SRC1203 TP AUK TO92 22K,22K SRA2203 TP AUK TO92 22K,22K KTA1273-TP-Y (KTA966A)KEC 2SC5343-L TP AUK TO92 2SA1980G TP AUK TO92 2SC5343-L TP AUK TO92 2SC5343-L TP AUK TO92 2SA1980G TP AUK TO92 2SC5344Y TP 2SA1980G TP AUK TO92 2SA1980G TP AUK TO92 2SA1980G TP AUK TO92 2SC5343-L TP AUK TO92 2SC5343-L TP AUK TO92 KTA1273-TP-Y (KTA966A)KEC 2SC5343-L TP AUK TO92 SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K 2SC5343-L TP AUK TO92 2SC5343-L TP AUK TO92 SRC1203 TP AUK TO92 22K,22K SRA2203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K 2SC5343-L TP AUK TO92 S1WBA60(1A 600V) SHIDENKEN EG01CW(R-FORM 5MM) TP SANKEN ERA18-02KFRB TP FUJI DO204AL 2 1SS133 DETECT,SW TP RL104F TP RECTRON NON 400V 1A 1N5822 BK RECTRON DO201AD 40V HER202 BK RECTRON NON 100V 2A RL104 R. TP GULF SEMICONDUCTOR 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP MTZ13C TP ROHM-K
B
! ! ! !
J
A F C DE G MN H KL I ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN FG ABCDEFGHI JKLMN ABCDEFGHI JKLMN KLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN CDEF H MN B DE J CDEF H MN B G J ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN B DEFGH J ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN FG ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN H ABCDEFGHI JKLMN
PART No.
MODEL HR-J595MS HR-J295MS HR-J595EK HR-J295EK HR-J293EU
MARK F G H I J
PART NAME, DESCRIPTION
MODEL HR-J282EU HR-J283EU HR-J582EU HR-J583EU
SPECIFICATION
MARK K L M N
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
****************************** PBM00 PBM00 PBM00 PBM00 PBM00 PBM00 PBM00 PBM00 PBM00 PBM00 IC101 ! IC102 IC103 IC201 IC301 IC501 IC501 IC503 IC504 IC505 IC751 IC7V1 IC801 IC901 Q151 Q152 Q154 Q155 Q157 Q162 Q163 Q164 Q165 Q166 Q301 Q302 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q501 Q502 Q503 Q504 Q514 Q515 Q5P2 Q5P3 Q5P4 Q5P5 Q5S1 Q7S1 Q901 Q902 Q903 Q906 ! BD101 D102 D103 D104 D105 D106 D109 D155 D156 D159 D160 D301 D502 D509 D901 D902 D903 D904 ZD151
MARK A B C D E
! !
ZD503 ZD801 ZD802 ZD803 ZD804 C101 C101 C102 C102 C103 C105 C106 C109 C112 C113 C114 C115 C116 C117 C120 C121 C127 C135 C153 C190 C201 C202 C203 C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C216 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 C324 C325 C326 C327 C328 C329 C330 C331 C333 C334 C335 C336 C337 C338 C339 C340 C341 C342 C343
LG-0DZ622609CA UZ5.6BSB-T2 UZ5.6BSB-T2 MTZ13AT-77 MTZ13AT-77 LG-624-088F LG-624-088L LG-624-088F LG-624-088L LG-0CE476CU611 LG-0CQ1031Y519 LG-624-087B QET41HM-106 LG-0CG3320U630 LG-0CG1010U510 LG-0CQ4732K409 LG-624-085D LG-0CE108BF630 LG-624-082H LG-0CE477BH630 LG-0CE227CH618 LG-0CN223AK948 LG-0CN4710K518 QET41CM-106 QET41CM-106 LG-0CN1030F678 LG-0CN1030F678 QET41HM-105 QET41HM-105 LG-0CN1040K948 LG-0CN1030F678 QET41HM-474 LG-0CN1030F678 LG-0CN1030F678 QET41HM-474 LG-0CN2220F668 LG-0CN2220F668 QET41HM-225 LG-0CN1030F678 QET41CM-476 LG-0CN1030F678 QET41HM-475 QET41CM-226 LG-0CN1220F668 QET41CM-476 LG-0CN1030F678 LG-0CN1220F668 QET41HM-105 LG-0CQ1532K409 LG-0CN1210K518 LG-0CQ1032K409 LG-0CE4765K618 LG-0CN1030F678 LG-0CQ2232L559 QET41CM-226 LG-0CE2253K636 QET41CM-106 LG-0CN8220F668 QET41HM-105 LG-0CQ1032K409 QET41HM-105 LG-0CX6800K408 QET41CM-106 QET41CM-106 QET41HM-475 QET41CM-106 LG-0CN1030F678 QET41HM-105 LG-0CN1030F678 LG-0CN1030F678 LG-0CN1040K948 QET41CM-106 QET41CM-476 LG-0CN4730K948 LG-0CN1030F678 QET41CM-476 QET41HM-105 LG-0CN4730K948 QET41HM-105 LG-0CN4730K948 LG-0CN223AK948 LG-0CN1040K948 LG-0CN4730K948
DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER CAPACITOR,DRAWING CAPACITOR,DRAWING CAPACITOR,DRAWING CAPACITOR,DRAWING CAPACITOR,AL.ELECTROLYTIC CAPACITOR,POLYESTER CAPACITOR CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,SEMI CERAMIC CAPACITOR,SEMI CERAMIC CAPACITOR,FIXED FILM CAPACITOR CAPACITOR,FIXED ELECTROLYTIC CAPACITOR CAPACITOR,AL.ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED FILM CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,POLYESTER(MYLAR) CAPACITOR,AL.ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,POLYESTER CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR,POLYESTER(MYLAR) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(T.C) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d
GDZJ6.2C 26MM TP GRANDE DO34 0 UZ-5.6BSB 26MM TP PYUNG CHANG UZ-5.6BSB 26MM TP PYUNG CHANG MTZ13A TP ROHM-K MTZ13A TP ROHM-K PCX2 275V 0.1UF,M (PILKO) 435D SUNIL ELECTRONICS 0.1UF/2 PCX2 275V 0.1UF,M (PILKO) 435D SUNIL ELECTRONICS 0.1UF/2 47UF SHL,SD 400V M FL BK7.5 0.01UF D 630V K PE NI TP HIGH-VOL 100P/1KV SMPS SAMHWA 10M SRA 50V M FM5 TP(5) 3300 PF 400V M E R(NK,AD,SD) 100 PF 400V K B R (NK,AD,SD) 0.047UF S 50V J PE TP CE 47UF/50V KME (SMPS) 1000UF KME 16V M FM5 BULK CE 1000UF/10V SHL(10*12.5)T/P 470UF KME TYPE 25V M FM5 BULK 220UF SHL,SD 25V 20% FL TP 5 0.022UF 50V Z F TA26 S 470P 50V K B TA26 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 0.01M 16V M Y TA26 0.01M 16V M Y TA26 1.0M SRA/SS50V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01M 16V M Y TA26 0.47M SRA 50V M FM5 TP(5) 0.01M 16V M Y TA26 0.01M 16V M Y TA26 0.47M SRA 50V M FM5 TP(5) 2200P 16V M X TA26 2200P 16V M X TA26 2.2UF SRA,SS 50V 20% FM5 TP 5 0.01M 16V M Y TA26 47M SRA/SS 16V M FM5 TP(5) 0.01M 16V M Y TA26 4.7UF SRA,SS 50V 20% FM5 TP 5 22M SRA 16V M FM5 TP(5) 1200P 16V M X TA26 47M SRA/SS 16V M FM5 TP(5) 0.01M 16V M Y TA26 1200P 16V M X TA26 1.0M SRA/SS50V M FM5 TP(5) 0.015UF S 50V J PE TP 120P 50V K B TA26 0.01UF S 50V J PE TP 47UF SR,SV 50V M FL TP 5 0.01M 16V M Y TA26 0.022UF S 63V K PP NI TP5 22M SRA 16V M FM5 TP(5) 2.2UF SRE,SE 50V 20% FM5 BP(D) 10M SRA 16V M FM5 TP(5) 8200P 16V M X TA26 1.0M SRA/SS50V M FM5 TP(5) 0.01UF S 50V J PE TP 1.0M SRA/SS50V M FM5 TP(5) 68P 50V J SL TA26 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 4.7UF SRA,SS 50V 20% FM5 TP 5 10M SRA 16V M FM5 TP(5) 0.01M 16V M Y TA26 1.0M SRA/SS50V M FM5 TP(5) 0.01M 16V M Y TA26 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 10M SRA 16V M FM5 TP(5) 47M SRA/SS 16V M FM5 TP(5) 0.047UF D 50V 80%,-20% F(Y5V) 0.01M 16V M Y TA26 47M SRA/SS 16V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 0.047UF D 50V 80%,-20% F(Y5V) 1.0M SRA/SS50V M FM5 TP(5) 0.047UF D 50V 80%,-20% F(Y5V) 0.022UF 50V Z F TA26 S 0.1UF D 50V 80%,-20% F(Y5V) TA 0.047UF D 50V 80%,-20% F(Y5V)
ABCDEFGHI JKLMN CDEF H MN CDEF H MN CDEF H MN CDEF H MN ABCDEFGHI J KLMN ABCDEFGHI J KLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN FG FG FG FG FG FG FG FG FG FG FG FG FG FG FG FG ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN
5-5
MODEL HR-J285EU HR-J290EU HR-J585EU HR-J590EU HR-J593EU
# REF No.
PART No.
PART NAME, DESCRIPTION
SPECIFICATION
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
C344 C345 C346 C347 C348 C349 C353 C355 C356 C357 C358 C359 C360 C361 C362 C363 C364 C365 C366 C367 C368 C369 C370 C371 C372 C373 C375 C500 C500 C501 C502 C503 C504 C505 C506 C508 C509 C510 C511 C512 C513 C514 C515 C516 C518 C519 C520 C523 C524 C525 C526 C527 C533 C534 C535 C543 C544 C545 C546 C547 C551 C552 C561 C564 C567 C570 C571 C575 C576 C577 C578 C581 C582 C583 C589 C596 C5A3 C5A4 C5A5 C5G2 C5G3 C5K1 C5P1
5-6
LG-0CN1010K518 LG-0CN4730K948 QET41CM-476 QET41HM-105 QET41HM-105 QET41CM-476 QET41HM-105 LG-0CN1040K948 QET41HM-105 QET41HM-105 LG-0CX6800K408 QET41HM-105 LG-0CN1040K948 LG-0CN223AK948 QET41CM-106 LG-0CN1030F678 QET41CM-476 QET41CM-106 LG-0CN1040K948 LG-0CN1040K948 LG-0CQ8224K409 LG-0CN1010K518 LG-0CN8200K419 LG-0CN8200K419 LG-0CN8200K419 LG-0CN1040K948 LG-0CN1020K518 LG-0CE4775C638 LG-624-074A LG-0CN1040K948 QET41CM-476 QET40JM-227 QET40JM-227 QET41CM-476 LG-0CN223AK948 LG-0CN1030F678 LG-0CC2200K415 QET40JM-227 LG-0CN1040K948 LG-0CN1020K518 LG-0CN1020K518 LG-0CC1200K415 LG-0CC1500K415 LG-0CN223AK948 LG-0CN1030F678 LG-0CN1040K948 LG-0CN1020K518 QET41HM-225 QET41CM-476 QET40JM-227 LG-0CE4764J638 LG-0CN2210K518 LG-0CN1020K518 QET41HM-475 QET41HM-475 LG-0CN2220F668 LG-0CQ4732K409 LG-0CN3330K518 LG-0CE4764J638 LG-0CN1030F678 LG-0CQ3332K409 LG-0CN1030F678 QET40JM-227 LG-0CN1020K518 LG-0CN1020K518 LG-0CC1500K415 LG-0CC1500K415 LG-0CN1020K518 LG-0CC2700K415 LG-0CN223AK948 LG-0CN2220F668 LG-0CN1030F678 LG-0CN1030F678 LG-0CN1040K948 LG-0CQ2232K409 LG-0CN1040K948 LG-0CN1040K948 LG-0CN1030F678 QET41HM-105 LG-0CE1086C638 LG-0CN1030F678 LG-0CN1040K948 LG-0CN1030F678
CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(T.C) CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED FILM CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,AL.ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED FILM CAPACITOR,FIXED TUBULAR(High d CAPACITOR,AL.ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED FILM CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR CERAMIC(TEMP COMP) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED FILM CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE)
100P 50V K B TA26 0.047UF D 50V 80%,-20% F(Y5V) 47M SRA/SS 16V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 47M SRA/SS 16V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 1.0M SRA/SS50V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 68P 50V J SL TA26 1.0M SRA/SS50V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 0.022UF 50V Z F TA26 S 10M SRA 16V M FM5 TP(5) 0.01M 16V M Y TA26 47M SRA/SS 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 0.0082UF TE 50V 5% PE TP5 100P 50V K B TA26 82PF D 50V 5% B(Y5P) TA52 82PF D 50V 5% B(Y5P) TA52 82PF D 50V 5% B(Y5P) TA52 0.1UF D 50V 80%,-20% F(Y5V) TA 1000P 50V K B TA26 470UF SR,SV 6.3V 20% FM5 TP 5 SUPER CAP 0.047F/5.5V T/P S/S 0.1UF D 50V 80%,-20% F(Y5V) TA 47M SRA/SS 16V M FM5 TP(5) 220M SRA 6.3V M FM5 TP(5) 220M SRA 6.3V M FM5 TP(5) 47M SRA/SS 16V M FM5 TP(5) 0.022UF 50V Z F TA26 S 0.01M 16V M Y TA26 22P 50V J NP0 TS 220M SRA 6.3V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 1000P 50V K B TA26 1000P 50V K B TA26 12P 50V J NP0 TS 15P 50V J NP0 TS 0.022UF 50V Z F TA26 S 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 1000P 50V K B TA26 2.2UF SRA,SS 50V 20% FM5 TP 5 47M SRA/SS 16V M FM5 TP(5) 220M SRA 6.3V M FM5 TP(5) 47UF SRA,SS 35V M FM5 TP 5 220P 50V K B TA26 1000P 50V K B TA26 4.7UF SRA,SS 50V 20% FM5 TP 5 4.7UF SRA,SS 50V 20% FM5 TP 5 2200P 16V M X TA26 0.047UF S 50V J PE TP 0.033UF 50V K B TA26 47UF SRA,SS 35V M FM5 TP 5 0.01M 16V M Y TA26 0.033UF S 50V J PE TP 0.01M 16V M Y TA26 220M SRA 6.3V M FM5 TP(5) 1000P 50V K B TA26 1000P 50V K B TA26 15P 50V J NP0 TS 15P 50V J NP0 TS 1000P 50V K B TA26 27P 50V J NP0 TP 0.022UF 50V Z F TA26 S 2200P 16V M X TA26 0.01M 16V M Y TA26 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 0.022UF S 50V J PE TP 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01M 16V M Y TA26 1.0M SRA/SS50V M FM5 TP(5) 1000000000 PF SMS,SG 6.3V M FM 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01M 16V M Y TA26
ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN B DE J A C FGHI KLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN
# REF No.
MARK A B C D E
PART No.
MODEL HR-J595MS HR-J295MS HR-J595EK HR-J295EK HR-J293EU
MARK F G H I J
PART NAME, DESCRIPTION
MODEL HR-J282EU HR-J283EU HR-J582EU HR-J583EU
SPECIFICATION
MARK K L M N
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
C5P2 C5R1 C5R2 C5S1 C5S3 C701 C703 C704 C705 C706 C707 C710 C711 C712 C713 C714 C751 C752 C753 C754 C755 C756 C757 C758 C759 C760 C761 C764 C765 C766 C769 C770 C771 C772 C773 C790 C7M2 C7M3 C7M6 C7S1 C7V1 C7V2 C7V3 C7V4 C7V5 C805 C806 C807 C808 C809 C810 C811 C813 C814 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C830 C831 C832 C835 C8R1 C8R2 C901 C902 C903 C904 C908 C909 C911 C912 C914 C915
LG-0CN1030F678 QET41CM-106 LG-0CN6810K518 LG-0CX4300K408 LG-0CN223AK948 QET41HM-475 QET41CM-106 QET41CM-476 LG-0CN1030F678 LG-0CE4775C618 LG-0CN1030F678 LG-0CX6800K408 LG-0CX3300K408 LG-0CX5R60K508 QET41CM-476 LG-0CN1030F678 QET41CM-476 LG-0CN1030F678 LG-0CX5600K408 LG-0CX5600K408 QET41CM-476 LG-0CN1030F678 QET41CM-476 QET41CM-106 QET41CM-106 LG-0CN1030F678 LG-0CN1030F678 LG-0CN1520F668 LG-0CN1520F668 QET41HM-335 QET41CM-106 LG-0CN1020K518 LG-0CN1030F678 LG-0CC0500K015 LG-0CC0800K015 LG-0CN1030F678 QET41CM-106 LG-0CX2700K408 LG-0CX2700K408 QET41CM-336 QET41CM-476 LG-0CN223AK948 QET41HM-105 LG-0CN4730K948 LG-0CN4730K948 LG-0CN1040K948 QET41HM-475 QET41HM-475 LG-0CN1040K948 LG-0CN1040K948 QET41CM-106 QET41CM-106 QET41CM-106 QET41CM-106 QET41CM-106 QET41HM-475 QET41CM-106 LG-0CQ6822K409 QET41CM-476 QET41CM-106 QET41CM-106 QET41CM-106 QET41CM-476 LG-0CQ6822K409 QET41CM-106 QET41CM-476 LG-0CN1030F678 LG-0CN1040K948 LG-0CN1030F678 QET41CM-476 QET41HM-474 LG-0CN1020K518 LG-0CN1020K518 LG-0CN1020K518 LG-0CE477CF638 LG-0CN1020K518 LG-0CN1020K518 LG-0CN1020K518 LG-0CN1040K948 LG-0CN1020K518 LG-0CE477CF638 LG-0CN1020K518 LG-0CN1040K948
CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(T.C) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,AL.ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(T.C) CAPACITOR TUBULA(T.C) CAPACITOR TUBULA(T.C) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,TUBULAR(T.C) CAPACITOR,TUBULAR(T.C) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR CERAMIC(TEMP COMP) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(T.C) CAPACITOR TUBULA(T.C) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,POLYESTER(MYLAR) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,POLYESTER(MYLAR) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,AL.ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,AL.ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(High d
0.01M 16V M Y TA26 10M SRA 16V M FM5 TP(5) 680P 50V K B TA26 43P 50V J SL TA26 0.022UF 50V Z F TA26 S 4.7UF SRA,SS 50V 20% FM5 TP 5 10M SRA 16V M FM5 TP(5) 47M SRA/SS 16V M FM5 TP(5) 0.01M 16V M Y TA26 470UF SR,SV 6.3V M FL TP 5 0.01M 16V M Y TA26 68P 50V J SL TA26 33P 50V J SL TA26 5.6PF 50V K SL TA26 47M SRA/SS 16V M FM5 TP(5) 0.01M 16V M Y TA26 47M SRA/SS 16V M FM5 TP(5) 0.01M 16V M Y TA26 56P 50V J SL TA26 56P 50V J SL TA26 47M SRA/SS 16V M FM5 TP(5) 0.01M 16V M Y TA26 47M SRA/SS 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 0.01M 16V M Y TA26 0.01M 16V M Y TA26 1500P 16V M X TA26 1500P 16V M X TA26 3.3UF SRA,SS 50V 20% FM5 TP 5 10M SRA 16V M FM5 TP(5) 1000P 50V K B TA26 0.01M 16V M Y TA26 5P 50V C NP0 TR 8P 50V C NP0 TS 0.01M 16V M Y TA26 10M SRA 16V M FM5 TP(5) 27P 50V J SL TA26 27P 50V J SL TA26 33M SRA 16V M FM5 TP(5) 47M SRA/SS 16V M FM5 TP(5) 0.022UF 50V Z F TA26 S 1.0M SRA/SS50V M FM5 TP(5) 0.047UF D 50V 80%,-20% F(Y5V) 0.047UF D 50V 80%,-20% F(Y5V) 0.1UF D 50V 80%,-20% F(Y5V) TA 4.7UF SRA,SS 50V 20% FM5 TP 5 4.7UF SRA,SS 50V 20% FM5 TP 5 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 4.7UF SRA,SS 50V 20% FM5 TP 5 10M SRA 16V M FM5 TP(5) 6800PF S 50V J PE TP 47M SRA/SS 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 47M SRA/SS 16V M FM5 TP(5) 6800PF S 50V J PE TP 10M SRA 16V M FM5 TP(5) 47M SRA/SS 16V M FM5 TP(5) 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01M 16V M Y TA26 47M SRA/SS 16V M FM5 TP(5) 0.47M SRA 50V M FM5 TP(5) 1000P 50V K B TA26 1000P 50V K B TA26 1000P 50V K B TA26 470UF SHL TYPE 16V M FM5 TP 5 1000P 50V K B TA26 1000P 50V K B TA26 1000P 50V K B TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 1000P 50V K B TA26 470UF SHL TYPE 16V M FM5 TP 5 1000P 50V K B TA26 0.1UF D 50V 80%,-20% F(Y5V) TA
ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN FG ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDE H I JKLMN ABCDE H I JKLMN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN ABCDEFGHI JKLMN CDEF H MN CDEF H MN CDEF H MN ABCDEFGHI JKLMN ABCDE H I JKLMN ABCDE H I JKLMN ABCDE H I JKLMN FG B DE J B DE J B DE J B DE J B DE J CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN BCDEFGH J MN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN A I KL ABCDEFGHI JKLMN B DEFGH J B DEFGH J B DEFGH J B DEFGH J
MODEL HR-J285EU HR-J290EU HR-J585EU HR-J590EU HR-J593EU
# REF No.
PART No.
PART NAME, DESCRIPTION
SPECIFICATION
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
C917 C920 C921 C952 C956 C957 C960 C961 C962 C963 C9A1 C9A2 C9A3 C9A4 C9A5 C9A6 C9A7 C9A8 R101 R102 R103 R104 R105 R106 R109 R112 R116 R117 R118 R119 R120 R125 R126 R151 R152 R153 R154 R155 R157 R158 R159 R161 R170 R172 R173 R201 R202 R204 R301 R303 R304 R305 R306 R307 R308 R309 R310 R311 R312 R313 R314 R315 R316 R317 R318 R319 R320 R321 R322 R323 R324 R325 R326 R327 R328 R329 R330 R331 R334 R335 R336 R337 R338
LG-0CX2700K408 LG-0CN1040K948 LG-0CN1040K948 LG-0CN1040K948 QET41HM-105 LG-0CX2700K408 LG-0CN1040K948 LG-0CN1040K948 QET41CM-106 QET41CM-106 QET41HM-105 QET41HM-105 QET41HM-105 LG-0CN1040K948 QET41CM-106 QET41CM-106 QET41CM-106 QET41CM-106 LG-614-007A QRD161J-184Y QRD161J-680Y LG-0RS5602K619 LG-0RF0101A619 QRD161J-184Y LG-0RS0350K619 QRD161J-104Y QRD161J-221Y QRD161J-222Y QRD161J-102Y LG-0RN3301F408 LG-0RN3001F408 QRD161J-472Y QRD161J-681Y QRD161J-102Y QRD161J-561Y QRD161J-102Y QRD161J-331Y QRD161J-332Y QRD161J-102Y QRD161J-183Y QRD161J-471Y QRD161J-472Y QRD161J-562Y QRD161J-271Y QRD161J-271Y QRD161J-102Y QRD161J-124Y QRD161J-473Y QRD161J-563Y QRD161J-183Y QRD161J-103Y QRD161J-103Y QRD161J-223Y QRD161J-222Y QRD161J-472Y QRD161J-102Y QRD161J-472Y QRD161J-102Y QRD161J-683Y QRD161J-2R2 QRD161J-102Y QRD161J-470Y QRD161J-101Y QRD161J-562Y QRD161J-392Y QRD161J-561Y QRD161J-151Y QRD161J-122Y QRD161J-102Y QRD161J-103Y QRD161J-334Y QRD161J-471Y QRD161J-123Y QRD161J-562Y QRD161J-271Y QRD161J-123Y QRD161J-103Y QRD161J-472Y QRD161J-272Y QRD161J-682Y QRD161J-104Y QRD161J-222Y QRD161J-271Y
CAPACITOR TUBULA(T.C) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(T.C) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC RESISTOR RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED METAL OXIDE FIL RESISTOR,DRAWING RESISTOR,FIXED CARBON FILM RESISTOR,FIXED METAL OXIDE FIL RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED METAL FILM RESISTOR,FIXED METAL FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM
27P 50V J SL TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 1.0M SRA/SS50V M FM5 TP(5) 27P 50V J SL TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 2.7/2W CEMENT SMPS V 180K OHM 1/6 W 5.00% TA26 68 OHM 1/6 W 5.00% TA26 56K OHM 2 W 5.00% TR 1 OHM 1/2 W(7.0) 5.00% TR 180K OHM 1/6 W 5.00% TA26 0.35 OHM 2 W 5.00% TR 100K OHM 1/6 W 5.00% TA26 220 OHM 1/6 W 5.00% TA26 2.2K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 3.3K OHM 1/6 W 1.00% TA26 3K OHM 1/6 W 1.00% TA26 4.7K OHM 1/6 W 5.00% TA26 680 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 330 OHM 1/6 W 5.00% TA26 3.3K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 18K OHM 1/6 W 5.00% TA26 470 OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 270 OHM 1/6 W 5.00% TA26 270 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 120K OHM 1/6 W 5.00% TA26 47K OHM 1/6 W 5.00% TA26 56K OHM 1/6 W 5.00% TA26 18K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 22K OHM 1/6 W 5.00% TA26 2.2K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 68K OHM 1/6 W 5.00% TA26 2.2 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 47 OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 3.9K OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 150 OHM 1/6 W 5.00% TA26 1.2K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 330K OHM 1/6 W 5.00% TA26 470 OHM 1/6 W 5.00% TA26 12K OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 270 OHM 1/6 W 5.00% TA26 12K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 2.7K OHM 1/6 W 5.00% TA26 6.8K OHM 1/6 W 5.00% TA26 100K OHM 1/6 W 5.00% TA26 2.2K OHM 1/6 W 5.00% TA26 270 OHM 1/6 W 5.00% TA26
B DEFGH J ABCDEFGHI JKLMN ABCDEFGHI JKLMN B G J ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN DEF DEF B G J B G J B G J B G J B G J B G J B G J B G J ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN FG FG FG ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN
# REF No.
MARK A B C D E
PART No.
MODEL HR-J595MS HR-J295MS HR-J595EK HR-J295EK HR-J293EU
PART NAME, DESCRIPTION
MARK F G H I J
MODEL HR-J282EU HR-J283EU HR-J582EU HR-J583EU
SPECIFICATION
MARK K L M N
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
R339 R340 R341 R342 R343 R344 R345 R346 R347 R349 R350 R351 R3A1 R501 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 R514 R515 R516 R517 R518 R520 R521 R522 R523 R524 R525 R526 R527 R528 R529 R530 R531 R535 R542 R543 R544 R546 R547 R548 R550 R553 R555 R556 R557 R558 R559 R560 R561 R562 R563 R564 R566 R567 R568 R569 R570 R575 R576 R577 R578 R579 R582 R583 R589 R591 R5A2 R5A3 R5A5 R5B3 R5B4 R5B5 R5C1
QRD161J-561Y QRD161J-183Y QRD161J-562Y QRD161J-561Y QRD161J-750Y QRD161J-471Y QRD161J-471Y QRD161J-101Y QRD161J-101Y QRD161J-182Y QRD161J-103Y QRD161J-824Y QRD161J-103Y QRD161J-101Y QRD161J-101Y QRD161J-472Y QRD161J-102Y QRD161J-102Y QRD161J-103Y QRD161J-103Y QRD161J-222Y QRD161J-222Y QRD161J-222Y QRD161J-102Y QRD161J-102Y QRD161J-102Y QRD161J-124Y QRD161J-271Y QRD161J-474Y QRD161J-471Y QRD161J-102Y QRD161J-392Y QRD161J-472Y QRD161J-102Y QRD161J-103Y QRD161J-220Y QRD161J-562Y QRD161J-562Y QRD161J-103Y QRD161J-472Y QRD161J-103Y QRD161J-472Y QRD161J-103Y QRD161J-474Y QRD161J-222Y QRD161J-101Y QRD161J-472Y QRD161J-562Y QRD161J-123Y QRD161J-104Y QRD161J-221Y QRD161J-221Y QRD161J-221Y QRD161J-223Y QRD161J-273Y QRD161J-223Y QRD161J-472Y QRD161J-472Y QRD161J-561Y QRD161J-561Y QRD161J-562Y QRD161J-273Y QRD161J-472Y QRD161J-103Y QRD161J-683Y QRD161J-105Y QRD161J-472Y QRD161J-472Y QRD161J-472Y QRD161J-472Y QRD161J-472Y QRD161J-563Y QRD161J-101Y QRD161J-103Y QRD161J-105Y QRD161J-104Y QRD161J-103Y QRD161J-103Y QRD161J-474Y QRD161J-102Y QRD161J-102Y QRD161J-101Y QRD161J-102Y
RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM
560 OHM 1/6 W 5.00% TA26 18K OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 75 OHM 1/6 W 5.00% TA26 470 OHM 1/6 W 5.00% TA26 470 OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 1.8K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 820K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 2.2K OHM 1/6 W 5.00% TA26 2.2K OHM 1/6 W 5.00% TA26 2.2K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 120K OHM 1/6 W 5.00% TA26 270 OHM 1/6 W 5.00% TA26 470K OHM 1/6 W 5.00% TA26 470 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 3.9K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 22 OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 470K OHM 1/6 W 5.00% TA26 2.2K OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 12K OHM 1/6 W 5.00% TA26 100K OHM 1/6 W 5.00% TA26 220 OHM 1/6 W 5.00% TA26 220 OHM 1/6 W 5.00% TA26 220 OHM 1/6 W 5.00% TA26 22K OHM 1/6 W 5.00% TA26 27K OHM 1/6 W 5.00% TA26 22K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 27K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 68K OHM 1/6 W 5.00% TA26 1M OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 56K OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 1M OHM 1/6 W 5.00% TA26 100K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 470K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26
ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN B DEFGH J ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN B DEFGH J ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN
5-7
MODEL HR-J285EU HR-J290EU HR-J585EU HR-J590EU HR-J593EU
# REF No.
PART No.
PART NAME, DESCRIPTION
SPECIFICATION
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
R5C5 R5C6 R5C7 R5C9 R5P2 R5P3 R5R2 R5R3 R5R4 R5R5 R5R7 R5R8 R5S1 R5T1 R5T2 R5T3 R5T4 R5T5 R5T9 R5T10 R5T11 R706 R707 R709 R753 R754 R755 R758 R759 R7M1 R7M2 R7M3 R7M5 R7S1 R7V1 R7V2 R7V3 R7V4 R7V5 R7V6 R7V7 R7V8 R7V9 R801 R802 R817 R818 R819 R820 R821 R822 R823 R824 R825 R826 R827 R828 R830 R831 R8R1 R8R2 R901 R902 R903 R903 R904 R905 R906 R911 R912 R913 R914 R943 R962 R963 R964 R965 R9C1 R9C2 R9M3 R9M4 FL301 L101
5-8
QRD161J-102Y QRD161J-102Y QRD161J-102Y QRD161J-103Y QRD161J-103Y QRD161J-103Y QRD161J-331Y QRD161J-331Y QRD161J-331Y QRD161J-331Y QRD161J-331Y QRD161J-102Y QRD161J-562Y QRD161J-182Y QRD161J-152Y QRD161J-222Y QRD161J-272Y QRD161J-392Y QRD161J-182Y QRD161J-152Y QRD161J-102Y QRD161J-221Y QRD161J-221Y QRD161J-102Y QRD161J-102Y QRD161J-332Y QRD161J-332Y QRD161J-472Y QRD161J-562Y QRD161J-102Y QRD161J-221Y QRD161J-102Y QRD161J-221Y QRD161J-223Y QRD161J-105Y QRD161J-104Y QRD161J-682Y QRD161J-564Y QRD161J-682Y QRD161J-564Y QRD161J-472Y QRD161J-101Y QRD161J-101Y QRD161J-472Y QRD161J-472Y QRD161J-335Y QRD161J-333Y QRD161J-272Y QRD161J-393Y QRD161J-272Y QRD161J-333Y QRD161J-471Y QRD161J-101Y QRD161J-561Y QRD161J-182Y QRD161J-102Y QRD161J-102Y QRD161J-472Y QRD161J-472Y QRD161J-561Y QRD161J-561Y QRD161J-750Y QRD161J-750Y QRD161J-392Y QRD161J-472Y QRD161J-473Y QRD161J-561Y QRD161J-561Y QRD161J-750Y QRD161J-750Y QRD161J-561Y QRD161J-561Y QRD161J-152Y QRD161J-101Y QRD161J-101Y QRD161J-821Y QRD161J-102Y QRD161J-123Y QRD161J-103Y QRD161J-473Y QRD161J-392Y LG-633-032K LG-636-004C
RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM COIL,IFT COIL
(VP)-V15
1K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 330 OHM 1/6 W 5.00% TA26 330 OHM 1/6 W 5.00% TA26 330 OHM 1/6 W 5.00% TA26 330 OHM 1/6 W 5.00% TA26 330 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 1.8K OHM 1/6 W 5.00% TA26 1.5K OHM 1/6 W 5.00% TA26 2.2K OHM 1/6 W 5.00% TA26 2.7K OHM 1/6 W 5.00% TA26 3.9K OHM 1/6 W 5.00% TA26 1.8K OHM 1/6 W 5.00% TA26 1.5K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 220 OHM 1/6 W 5.00% TA26 220 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 3.3K OHM 1/6 W 5.00% TA26 3.3K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 5.6K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 220 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 220 OHM 1/6 W 5.00% TA26 22K OHM 1/6 W 5.00% TA26 1M OHM 1/6 W 5.00% TA26 100K OHM 1/6 W 5.00% TA26 6.8K OHM 1/6 W 5.00% TA26 560K OHM 1/6 W 5.00% TA26 6.8K OHM 1/6 W 5.00% TA26 560K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 3.3M OHM 1/6 W 5.00% TA26 33K OHM 1/6 W 5.00% TA26 2.7K OHM 1/6 W 5.00% TA26 39K OHM 1/6 W 5.00% TA26 2.7K OHM 1/6 W 5.00% TA26 33K OHM 1/6 W 5.00% TA26 470 OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 1.8K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 75 OHM 1/6 W 5.00% TA26 75 OHM 1/6 W 5.00% TA26 3.9K OHM 1/6 W 5.00% TA26 4.7K OHM 1/6 W 5.00% TA26 47K OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 75 OHM 1/6 W 5.00% TA26 75 OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 560 OHM 1/6 W 5.00% TA26 1.5K OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 100 OHM 1/6 W 5.00% TA26 820 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5.00% TA26 12K OHM 1/6 W 5.00% TA26 10K OHM 1/6 W 5.00% TA26 47K OHM 1/6 W 5.00% TA26 3.9K OHM 1/6 W 5.00% TA26 BIAC OSC,1CHIP 5V(KS-75M) KWAN BEAD CORE BFS3550R2FD8,R T/P
E. & O. E. No.82915
ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN ABCDE H I JKLMN ABCDE H I JKLMN ABCDE H I JKLMN ABCDE H I JKLMN FG B DE J B DE J B DE J B DE J B DE J B DE J B DE J B DE J B DE J CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN CDEF H MN ABCDEFGHI JKLMN ABCDEFGHI JKLMN A I KL BCDEFGH J MN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN B DEFGH J B DEFGH J B DEFGH J B DEFGH J ABCDEFGHI JKLMN B G J B G J ABCDEFGHI JKLMN ABCDEFGHI JKLMN B DEFG J B DEFG J A I KL A I KL ABCDEFGHI JKLMN ABCDEFGHI JKLMN
# REF No.
MARK A B C D E
PART No.
MODEL HR-J595MS HR-J295MS HR-J595EK HR-J295EK HR-J293EU
PART NAME, DESCRIPTION
MARK F G H I J
MODEL HR-J282EU HR-J283EU HR-J582EU HR-J583EU
SPECIFICATION
MARK K L M N
ABCDEFGHI JKLMN
---- ------- ----------------------- -------------------------------------- -------------------------------------- ------------------------
! L102 LG-616-145H L103 LG-633-088G L104 LG-633-088G L106 LG-636-004C L201 LG-0LR1000K035 L301 LG-0LR0102J0N5 L302 LG-0LR1000K035 L303 LG-0LR0102J0N5 L304 LG-0LR0102J0N5 L305 LG-0LR1000K035 L307 LG-0LR0102J0N5 L501 LG-0LA0122K018 L503 LG-0LR1000K035 L504 LG-0LR0102J0N5 L505 LG-0LR1000K035 L506 LG-635-027C L5G2 LG-0LR3300K035 L5S1 LG-0LA0332K018 L702 LG-0LR1000K035 L703 LG-0LR1000K035 L704 LG-0LA0821K018 L705 LG-0LR1000K035 L751 LG-0LR0102J0N5 L753 LG-0LR0102J0N5 L7V1 LG-0LR1000K035 L801 LG-0LR0102J0N5 L802 LG-0LR0102J0N5 L8R1 LG-0LA1000K018 L8R2 LG-0LA1000K018 L901 LG-0LA1000K018 L902 LG-0LA1000K018 L904 LG-0LA1000K018 L905 LG-636-004C L906 LG-0LA1000K018 L907 LG-636-004C L911 LG-0LA1000K018 L912 LG-0LA1000K018 L914 LG-0LA1000K018 L915 LG-0LA1000K018 CS501 LG-6600M000002 ES501 LG-4931R-0050C ES502 LG-4931R-0050C ! F101 LG-585-011T ! FH01 LG-586-008B ! FH02 LG-586-008B JK801 LG-6612R-C002C JK901 LG-6620RM0002J JK901 LG-6620RM0002K JK901 LG-6620RM0002L LD501 LG-4931R-0017C LED502 LG-6301R2U001F MS501 LG-6600JB8005B P3D01 LG-561-234S P3D01 LG-561-234Z P3D02 LG-6630R5S010A P3D03 LG-561-251B PMC01 LG-6630R-BE01L ! PW101 LG-561-292B RC501 LG-6712R1940GA RS501 LG-6500RAB003A RS502 LG-6500RAB003A SW5T1 LG-556-213C SW5T10 LG-556-213C SW5T11 LG-556-213C SW5T12 LG-556-213C SW5T13 LG-556-213C SW5T3 LG-556-213C SW5T4 LG-556-213C SW5T5 LG-556-213C SW5T6 LG-556-213C ! T101 LG-642-015G TU701 LG-6700PFPL03A TU701 LG-6700PFPL03B TU701 LG-6700PFPL03E X301 LG-6202R2443AC X501 LG-6212AA2100C X502 LG-6202R-DA01A X751 LG-529-021Q
FILTER(CIRC) SHT LFS2020V4-04350 COIL,CHOKE CHOCK(22MH) 5MM TOKO TP COIL,CHOKE CHOCK(22MH) 5MM TOKO TP COIL BEAD CORE BFS3550R2FD8,R T/P INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR AXIAL LEAD 12M K 2.3X3.4 L5 TP INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR,RADIAL LEAD EL0405RA SKI150G-3 K-TDK 15UH INDUCTOR RADIAL LEAD 330M K 6X6 L5 TP INDUCTOR AXIAL LEAD 33M K 2.3X3.4 L5 TP INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR AXIAL LEAD 8.2M K 2.3X3.4 L5 TP INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR RADIAL LEAD 100M K 6X6 L5 TP INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR,RADIAL LEAD 10UH 5% TP 3X5 TR5 INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP COIL BEAD CORE BFS3550R2FD8,R T/P INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP COIL BEAD CORE BFS3550R2FD8,R T/P INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP INDUCTOR AXIAL LEAD 100M K 2.3X3.4 L5 TP SWITCH,PUSH MPU11810MLB0 MIC DC 5V 1MA D-3 HOLDER ASSEMBLY END (DI) HOLDER ASSEMBLY END (DI) FUSE,SLOW BLOW 1600MA 250 V 5.2X20 CY/GL SEMK HOLDER FUSE CLIP TP SINSUNG HOLDER FUSE CLIP TP SINSUNG JACK,RCA RCA-208C-06 YUQIU WH-RD JACK,SCART DSAM-0121 DOOWON 2F-21P(BL-BK) JACK,SCART DSAM-0120 DOOWON 1F-21P (BK) JACK,SCART DSAM-0139 DOOWON 2F-21P(BK-BK) HOLDER ASSY LED(DI-CKD)LOCAL LED ASSEMBLY TOH-30M-G3R1 OASIS UNIVERSAL 4 SWITCH,MODE NON 5V 1MA VERTICAL -G CONNECTOR(CIRC),DRAWING GF120-9S-TS-A LG CABLE 9P 1.25 CONNECTOR (CIRC) GF120-3S-TS-A LGC 3PIN 1.25MM CONNECTOR (CIRC) GF105-06S-TS LG CABLE 6PIN 2MM CONNECTOR(CIRC),DRAWING GB201-2P-TS-B(LGC) CONNECTOR (CIRC),BOARD TO BOARJE612-12 JAE EUN 12P 2.0MM CONNECTOR GP390 LGC 3P 3.96 STRAIGHT SN REMOTE CONTROLLER RECEIVER TSOP2840WE1 VISHAY(TEMIC) 40KH SENSOR SG-260 KODENSHI D33 REEL SENSO SENSOR SG-260 KODENSHI D33 REEL SENSO SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 SWITCH,DETECTOR THVV951BAA POSTECH DC 12 V 5-0 TRANSFORMER,SMPS SJE-015G/SHT-015G SJ/SH/CS/LSE TUNER SECAM TADC-S301D LG PAL FS Y2K TUNER B/G TADC-G301D LG PAL FS Y2K2 TUNER G/K/I TADC-M301D LG PAL FS Y2 RESONATOR,CRYSTAL HC49U BUBANG 4-433709MHZ 15 RESONATOR,CRYSTAL HC-49S BUBANG 10MHZ +/- 30 PPM RESONATOR,CRYSTAL CFS-308 CITIZEN 32-768KHZ RESONATOR,CRYSTAL 49U BUBANG 18432000HZ 30PPM 16
ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN FG ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDE H I JKLMN CDEF H MN CDEF H MN B DE J CDEF H MN CDEF H MN CDEF H MN CDEF H MN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN B DEFGH J B DEFGH J B DEFGH J B DEFGH J ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN CDEF H MN B DEFG J AC I KLMN H ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN CDEF H MN AB G I JKL ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN FG AB J CDE H I KLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN ABCDEFGHI JKLMN CDEF H MN
