DV-NC55S/H DV-NC60H
SERVICE MANUAL S01B9DV-NC55S
SERVICE MANUAL
VCR/DVD COMBINATION MODEL REW
PLAY STOP
PLAY
EJECT/ STOP
POWER
OPEN/ CLOSE
STANDBY
/
VCR DVD (AV 1 )
CH(TRACKING)
AV 2 IN VDEO L(MONO)-AUDIO-R
DV-NC55S/H
OPERATE
DVD / CD / VIDEO CD PLAYER
EJECT/ STOP
/
REW
PLAY/X2
CH
REC
DVD OUT
PLAY
STOP
VCR DVD (LINE 3 )
OPEN/ CLOSE
LINE 3 IN VDEO L(MONO)-AUDIO-R
MODELS
DV-NC55S DV-NC55H DV-NC60H
VCR/DVD COMBINATION MODEL
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used.
DV-NC60H
QSURROUND
CONTENTS
MODELS DV-NC55S/H/60H
Page 1. IMPORTANT SERVICE NOTES ........................................................................................................ 2 2. FEATURES ........................................................................................................................................ 3 3. SPECIFICATIONS ............................................................................................................................. 3 4. PART NAMES .................................................................................................................................... 5 5. MAINTENANCE CHECK ITEMS AND EXECUTION TIME ............................................................... 9 6. DISASSEMBLY METHOD ............................................................................................................... 10 7. OPERATION OF PICKUP ............................................................................................................... 14 8. ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS ............................ 15 9. ELECTRICAL ADJUSTMENT .......................................................................................................... 38 10. TEST MODE .................................................................................................................................... 41 11. TROUBLESHOOTING ..................................................................................................................... 44 12. IC FUNCTION LIST ......................................................................................................................... 58 13. BLOCK DIAGRAMS ......................................................................................................................... 82 14. SCHEMATIC DIAGRAMS ................................................................................................................ 92 15. PRINTED WIRING BOARD ASSEMBLIES ................................................................................... 114 16. REPLACEMENT PARTS LIST ...................................................................................................... 137 17. PACKING OF THE SET ................................................................................................................. 159
SHARP CORPORATION 1
DV-NC55S/H DV-NC60H
1. IMPORTANT SERVICE NOTES Note: This unit can be used only where the power supply is AC 230V-240V, 50Hz. It cannot be used elsewhere.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
• This Unit is classified as a CLASS 1 LASER product. • The CLASS 1 LASER PRODUCT label is located on the rear cover. • This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
CLASS 1 LASER PRODUCT
DO NOT STARE INTO THE LASER BEAM OR VIEW WITH OPTICAL INSTRUMENT.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. (Rear of product)
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. Laser Diode Properties Material: AlGaInP Wave length: 650 nm Emission Duration: Continuous Laser output: Max. 0.7 mW
Power Lead Protection To avoid any malfunctions of the unit, and to protect against electric shock, fire or personal injury, please observe the following. • Hold the plug firmly when connecting or disconnecting the AC power lead. • Keep the AC power lead away from heating appliances. • Never put any heavy object on the AC power lead. • Do not attempt to repair or reconstruct the AC power lead in any way.
VARO! AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE. ÄLÄ TUIJOTA SÄTEESEEN ÄLÄKÄ KATSO SITÄ OPTISEN LAITTEEN LÄPI. VARNING - LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN STRÅLEN OCH BETRAKTA EJ STRÅLEN GENOM OPTISKT INSTRUMENT.
2
DV-NC55S/H DV-NC60H
2. FEATURES
Ë Common Features • A DVD, AUDIO CD player and VCR all in one. • Simultaneous VCR recording and DVD playback. Ë VCR • Hi-Fi Stereo Sound/Double-Azimuth 4-Heads • 1 minute Rewind (E-180) • S-VHS Simple Playback • HQ (High Quality) Circuitry • Simple Recording Timer • Sharp Super Picture Ë DVD • Plays DVD and Audio CD discs as well as CD-R/CD-RW discs recorded in MP3 file format • Virtual Dolby Surround (QSURROUND*1) provides high-quality surround sound • Digital Gamma correction and Digital Super Picture functions • Dolby Digital*2, DTS*3, MPEG Audio digital out capability • High-quality digital images • High-quality digital sound *1 QSURROUNDTM is a trademark of QSound Labs, Inc. *2 Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories. *3 "DTS" and "DTS Digital Surround" are trademarks of Digital Theater Systems, Inc.
3. SPECIFICATIONS Signal System: PAL INPUT/OUTPUT JACKS DVD/VCR shared output jacks: VIDEO jack: RCA Pin-jack AUDIO jack: RCA Pin-jack DVD output jacks: VIDEO jack: S-Video jack AUDIO jack: RCA Pin-jack DIGITAL AUDIO IF: Coaxial digital AUDIO output jack: RCA Pin-jack VIDEO input jacks: VIDEO jack: SCART AUDIO jack: SCART VCR Video Recording System: Number of Video Heads: Video Signal Standard: Audio Recording System:
Rotary Two-Head Helical Scanning 4 NTSC Colour System 1 Stationary Head for Linear Audio 2 Rotary Heads for Hi-Fi stereo Tape Width: 12.7 mm Tape Speed (PAL): (SP) 23.39 mm/sec (LP) 11.70 mm/sec (EP) 7.80 mm/sec (NTSC) (SP) 33.35 mm/sec (Playback only) (LP) 16.67 mm/sec (Playback only) (EP) 11.12 mm/sec (Playback only)
3
DV-NC55S/H DV-NC60H Recording/Playback Time: (SP) 240 min (With E-240 Cassette) (LP) 480 min (With E-240 Cassette) (EP) 720 min (With E-240 Cassette) Channel Coverage: UHF E21-E69 Antenna Input: 75Ω Video Input: Input level: 0.5 to 2.0 Vp-p (75Ω) Video Output: Output level: 1.0 Vp-p (75Ω) Audio Output: Output level: –3.8 dBs (47kΩ) (0 dBs = 0.775 Vrms) Audio Output: Output level: –8 dBs (1kΩ) (0 dBs = 0.775 Vrms) Hi-Fi Audio: Dynamic Range: 90 dB Frequency Response: 20 Hz-20 kHz Memory Backup: 60 seconds (55H/60H) 60 minutes (60S) DVD DVD/VCR shared Video output: Output level: 1 Vp-p (75Ω) S video output: Y output level: 1 Vp-p (75Ω) C output level: 0.286 Vp-p (75Ω) Audio output: Output level: 2 Vrms (1 kHz, 0 dB) Video signal horizontal resolution: 500 lines S/N ratio: 60 dB Audio signal frequency characteristics: For DVD linear PCM playback: 4 Hz to 22 kHz (48 kHz sampling) 4 Hz to 44 kHz (96 kHz sampling) CD playback: 4 Hz to 20 kHz (JEITA) S/N ratio: CD: 100 dB, 1 kHz (EIAJ) Dynamic range: DVD linear PCM: 96 dB (JEITA) CD: 96 dB (JEITA) Total harmonic distortion ratio: CD: 0.006% (JEITA) Pickup: Wave length: 650 nm (DVD) / 780 nm (CD) Laser output: Max. 0.7 mW Operating temperature: Storage temperature: Power supply: Power consumption: Dimensions: Weight:
5°C to 35°C (41°F to 95°F) –20°C to 55°C (–4°F to 131°F) 230V-240V AC, 50 Hz 29 W 430 mm × 99 mm × 363 mm (W × H × D) 6.3 kg
Specifications are subject to change without notice. Weight and dimensions are approximate.
3-1. ACCESSORIES Accessories:
Remote Control Unit x 1, Battery x 2, 21Pin Cable x 1, RF Cable x 1, Operation Manual x 1, Quick Start Guide x 1
4
DV-NC55S/H DV-NC60H
5. MAINTENANCE CHECK ITEMS AND EXECUTION TIME MECHANICAL PARTS REGUIRING PERIODICAL INSPECTION Use the following table as a guide to maintain the mechanical parts in good operating condition. Parts Pickup Spindle Unit Sled Motor Loading Motor Belt Note
Maintained
1,000 hrs.
2,000 hrs.
: Part Replacement : Cleaning (For cleaning, use a lint-free cloth danpened with pure isopropyl alcohol.)
CARES WHEN USING THE PICKUP 1. The laser light having wavelength 650 nm is emitted from the objective lens. BE CAREFUL SO THAT THE LASER LIGHT DOES NOT ENTER DIRECTLY INTO YOUR EYE. 2. The semiconductor laser may be easily damaged by electrostatic charges. When handling the pickup, take care so that the electrostatic charge is not generated. 3. The semiconductor laser may be easily damaged by overcurrent. Use the power supply unit which does not give any spike current when the power is turned on and off. 4. Carefully remove the dust and dirt from the objective lens with the lens blower. When handling the objective lens, take due care so that it is not contaminated with fingerprint, etc. If the objective lens is contaminated, impregnate the cleaning paper with a small quantity of solvent (isopropyl alcohol), and gently wipe to clean. 5. The ozone layer depleting components (ODC) are not used in the production process for the product.
9
DV-NC55S/H DV-NC60H 1
6. DISASSEMBLY METHOD
4
2
6-1. DISASSEMBLY METHOD
3
1) Removing the cabinet. (1) Remove the seven screws 1 and 2. 1
2) Removing the rear panel. (1) Remove the ten screws 3. (2) Remove the three screws 4.
3) Removing the front panel. (1) Remove the three screws 5. (2) Remove the three hooks 6. 4) Removing the front PWB. (1) Remove the four FFCs 7 and 8. (2) Release the two hooks 9 and tilt the PWB toward you to remove it. (3) Release the two hooks 0 and tilt the PWB toward you to remove it.
Ｈ 9 Shild Plate 5
8 10
8 5
7 6
Ｈ
DV-NC55S/H
11
5) Removing the DVD mechanism. (1) Remove the four screws q. (2) Remove the two screws w. (3) Remove the DVD REINF. angle e. (4) Remove the three connectors r. (5) Remove the two FFCs t.
11
7
6 DV-NC60H
12
Ｈ
11 14 13
14
15 15
26
(6) Remove the FFC y. (7) Remove the shield (lower) u. (8) Remove the FFC i, and at connector o, and at four screws p. (9) Remove the wire from the wire holder a. (10)Remove the DVD main PWB s. (11)Remove the FFC cover d. (12)Remove the two interface PWB holders f, and remove the interface PWB g. (13)Remove the two screws h.
25
24 23 21 22 18
19
20 16
10
17
DV-NC55S/H DV-NC60H (14)Remove the connectors j. (15)Remove the five screws k and l.
27
29 28
6) Removing the cassette housing control/VCR mechanism. (1) Remove the two screws ;. (2) Remove the two screws 31 . (3) Remove the one screw 32 .
30
31
32
33
7) Removing the terminal plate. (1) Remove the four screws 33 .
34
8) Removing the VCR main PWB. (1) Remove the one screw 34 . 9) Removing the bottom plate. (1) Remove the six screws 35 .
35
11
DV-NC55S/H DV-NC60H
6-2. EXTENSION CABLE USE POINT (FOUR PLACES) Parts Code QCNW-8600AJZZ
Price Code AD
QCNW-8601AJZZ
AE
QCNW-8605AJZZ
AE
QCNW-8607AJZZ
AG
QCNW-8609AJZZ
AF
QCNW-A224WJZZ
AE
QCNW-A225WJZZ
AD
QCNW-A227WJZZ
AC
QCNW-A256WJZZ
AH
QCNW-A226WJZZ
AB
Name/Description Extension cable (FFC), 29pin DVD main CN801–INTERFACE CN8202 Extension cable (FFC), 23pin INTERFACE CN8203–DVD display CN5001 Extension cable (FFC), 9pin DVD main CN802–AV SC2003 Extension cable(wire), 9pin DVD main CN201– POWER P9001 Extension cable(wire), 11pin INTERFACE CN8201– POWER P9002 Extension cable(shield wire), 2pin DVD main CN803– AV SC2004 Extension cable(shield wire), 2pin VCR main P1201– INTERFACE CN6101 Extension cable(FFC), 9pin INTERFACE CN6102– AV CN2005 Extension cable(wire), 12pin VCR main P9601– POWER P9003 Extension cable(FFC), 19pin AV SC2001– TERMINAL SC2505 AV SC2002– TERMINAL SC2504
Extension Cable Diagram Tuner
Terminal PWB
QCNW-A226WJZZ 19PIN
SC2505
QCNW-A256WJZZ 12PIN
SC2504 Power PWB
P1201 SC2003 SC2004 P9601
P9002 P9001
P9003
SC2001 SC2002 CN2005
DVD Mechanism
AV PWB
QCNW-A227WJZZ QCNW-A225WJZZ 9PIN 2PIN VCR Main PWB
CN6102
QCNW-8609AJZZ CN8201 11PIN
QCNW-A224WJZZ 2PIN
QCNW-8607AJZZ 9PIN
CN6101
VCR Mechanism
CN201
CN803 DVD Main PWB
CN8203 CN8202 Interface PWB
CN801 QCNW-8600AJZZ 29PIN
CN5001 VCR Display PWB
DVD Display PWB
QCNW-8601AJZZ 23PIN
12
CN802
QCNW-8605AJZZ 9PIN
DV-NC55S/H DV-NC60H
6-3. REPLACEMENT OF MAIN PARTS 1. Remove the mechanism with angle from the set (refer to 35 on page 156). 2. It is in such cases as the thin driver, and it is pushed in slowly, and a tray is drawn in the arrow direction the slide rack on the left of the base chassis. 3. Take out disk. Front Side
1. After setting the mechanism chassis to the angle state, ground it to prevent the electrostatic discharge damage of the pickup. 2. Remove S and the DVD shield (lower) 56 (refer to the illustration on page 156). 3. Remove P , Q , Z and R 83 from the DVD main PWB unit 68 , and loosen the 4 screws 45 to remove the DVD main PWB unit 68 . (Pickup relay FFC 74 isn't removed.) (refer to the illustration on page 156) 4. Remove screws fixing the base chassis (located at the back right and at front left when facing the set). 5. With the pickup FFC connected, turn over the base chassis and short (solder) two short lands on the pickup interface PWB in order to prevent the electrostatic discharge damage of the pickup. 6. Remove the pickup FFC from the main PWB. 7. Remove the pickup FFC from the pickup interface PWB. 8. Remove the traverse mounting screws to remove the traverse chassis ass'y. Note: After assembly and wiring, remove the solder joint of the short land. If short-circuited, a disk is not played back. Pickup FFC
Traverse Fixing Screw
Sled Motor Lead Wire
Loading Motor Lead Wire
Since the pickup optical axis and turntable inclination of DVD are adjusted with higher accuracy than of CD/MD, make a replacement as a mechanism service chassis ass'y (refer to Parts List).
Pickup FFC
Pickup interface PWB
13
Short Land
DV-NC55S/H DV-NC60H
7. OPERATION OF PICKUP 7-1. CIRCUIT CONFIGURATION OF PICKUP The pickup unit reads signals from the disk, and the flexible cable is connected to the board. The following signals flow through the cable.
7-3. POLARITIES OF SIGNAL
7-2. EQUIVALENT CIRCUIT OF PICKUP FO+ 1
TR–
2
FO+
3
TR+
4
FO–
5
VR
6
PD
7
VCC
LD
8
GND
PD
9
LD
VA
10
GND
VB
11
VOS
VC
12
NC
VD
13
NC
14
Vref(VCC/2)
15
VA
16
VD
17
NC
18
GND
19
VB
20
VC
TR– TR+ FO– ACTUATOR
Power adjust
HIGH-FREQUENCY CONVOLUTION VOS OSC
– + – + – + – +
Vref Vcc GND HOLOGRAM LASER UNIT
Focus FO+, FOTracking TR+, TR-
When electric current is flowed from FO+ to FO-, the lens comes to near the disk. When electric current is flowed from TR+ to TR-, the lens goes toward the outer circumference.
(NC)
1
7-4. SIGNALS OF PICKUP 7-4-1. Tracking drive signal (TR+, TR-) The signal drives the tracking servo mechanism which projects the beam on the track by moving the objective lens (OL) to the outer or inner circumference (at a right angle against the track) of the disk.
7-4-2. Focus drive signal (FO+, FO-) The signal drives the focus servo mechanism which aligns the focus on the pit of the disk by elevating OL (vertically against the disk surface.) 2-focus objective lens
The VR terminal is connected to GND. Actuator assembly
7-4-3. Monitor Diode (PD)
Since the laser diode largely varies output of the laser light even if the flowing current is slightly varied, the projection light is detected with the monitor diode to control the laser light to be equally output. Since the current varies on the monitor diode according to the intensity of the received light of the laser diode, the drive current of the laser diode is reduced if the current of the monitor diode increases. On the contrary, the drive current of the laser diode is increased if the current of the monitor diode decreases. As the projection light of the laser diode becomes stronger, the current of the monitor diode increases to increase the current which flows into the monitor diode output (PD). This is input to the pin 44 of IC301 and is compared with the reference voltage to control the drive current of the laser diode. LD PD When the quantity of laser light increases, the The circuit is called ALPC (Automatic Laser Power Control). current shown in figure increases and the PD terminal voltage rises. IC301 is used to control. The LD terminal voltage 7-4-4. Laser diode drive current control (LD) lowers, and the quantity of light reduces. (IC301 is Power supply to drive the laser diode actuated by voltage input.)
7-4-5. High-frequency convolution module power supply (VOSC) The high-frequency convolution imposes the high-frequency signal on the DC current to impose the high frequency on the drive current of the laser. Thus, the interference of outgoing light and reflected light is prevented.
7-4-6. HF Signal (VA, VB, VC, VD) Signals recorded in the disk
14
DV-NC55S/H DV-NC60H
8. ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS The explanation given below relates to the on-site general service (field service) but it does not relates to the adjustment and replacement which need high-grade equipment, jigs and skill. For example, the drum assembling, replacement and adjustment service must be performed by the person who have finished the technical courses.
8-1. MECHANISM CONFIRMATION ADJUSTMENT JIG So as to perform completely the mechanism adjustment prepare the following special jigs. So as to maintain the initial performance of the machine the maintenance and check are necessary. Utmost care must be taken so that the tape is not damaged. If adjustment needs any jig, be sure to use the required jig. No.
Jig ltem
Part No.
Code
1.
Torque Cassette Meter
JiGVHT-063
CZ
JiGTG0090
CM
2.
Torque Gauge JiGTG1200
CN
3.
Torque Gauge Head
JiGTH0006
AW
4.
Torque Driver
JiGTD1200
CB
Master Plane Jig and Reel Disk Height Adjusting Jig
JiGRH0002
BR
5.
JiGMP0001
BY
JiGSG2000
BS
JiGSG0300
BF
6.
Configuration
Remarks This cassette torque meter is used for checking and adjusting the torque of take-up for measuring tape back tension.
These Jigs are used for checking and adjusting the torque of take-up and supply reel disks.
When fixing any part to the threaded hole using resin with screw, use the jig. (Specified torque 5 kg) These Jigs are used for checking and adjusting the reel disk height. There are two gauges used for the tension measurements, 300 g and 2.0 kg.
Tension Gauge
7.
Pinch pressing force measuring jig
JiGADP0003
BK
This Jig is used with the tension gauge. Rotary transformer clearance adjusting jig.
8.
Reverse guide height adjustment box driver
JiGDRiVER11055
AR
This Jig is used for height adjustment of the reverse guide (for reverse guide height adjustment). Video
9.
Alignment Tape
VROUBZFS CK VROCPSV
Guide roller height
10. adjustment driver X value adjustment 11. gear driver 12.
Reverse Guide Height Adjusting Jig
Audio
Track
625 Monoscope 6kHz 35µm 625 Monoscope 6kHz and and 49µm Colour bar 1kHz This screwdriver is used for adjusting the guide roller height.
JiGDRiVERH-4 AP JiGDRiVER-6
BM
For X value adjustment
JiGRVGH-F18
BU
This Jig is used for height adjustment of the reverse guide.
15
DV-NC55S/H DV-NC60H
8-2. MAINTENANCE CHECK ITEMS AND EXECUTION TIME Perform the maintenance with the regular intervals as follows so as to maintain the quality of machine. Parts
Possible symptom encountered
Maintained 500 1000 1500 2000 hrs. hrs. hrs. hrs.
Remarks Abnormal rotation or significant vibration requires replacement.
Guide roller ass’y Sup guide shaft
Lateral noises Head occasionally blocked
Reverse guide
Clean tape contact part with the specified cleaning liquid.
Slant pole on pole base Color and beating
Full erase head
Small sound or sound distortion Poor S/N ratio, no color Poor flatness of the envelope with alignment tape No tape running, uneven color No tape running, tape slack No tape running, tape slack, no fast forward/ rewind motion
A/C head Upper and lower drum ass’y Capstan D.D. motor Pinch roller Reel belt Tension band ass’y
Screen swaying
Loading motor
Cassette not loaded or unloaded
Idler ass’y
Clean tape contact area with the specified cleaning liquid.
Clean rubber and rubber contact area with the specified cleaning liquid.
No tape running, tape slack
Limiter pulley Supply/take-up main brake levers
Tape slack Replace the roller of the cleaner when it wears down. Just change the AHC roller assembly for new one.
AHC (Automatic head cleaner)
NOTE : Part replacement. : Cleaning : Apply grease Cleaning liquid Industrial ethyl alcohol * This mechanism does not need electric adjustment with variable resistor. Check parts. If any deviation is found, clean or replace parts. Video head cleaning procedure 1. Apply one drop of cleaning liquid to the cleaning paper with the baby oiler. 2. Gently press the cleaning paper against the video head to fix your finger, and move the upper drum so that each head is passed to and fro 5 times (do not move the cleaning paper). 3. Wipe with the dry cleaning paper. Rotate the upper drum Notes : • Use the commercially available ethanol of Class 1 as cleaning liquid. • Since the video head may be damaged, do not move up and down the cleaning paper. • Whenever the video head is cleaned, replace the cleaning paper. • Do not apply this procedure for the parts other than the video head. 16
with one hand. Gently press the cleaning paper to fix with your finger, and rotate the upper drum to clean. Move to and fro 5 times for each head. (Do not move the cleaning paper.)
Parts Code ZPAPRA56-001E ZOiLR-02-24TE
Description Cleaning Paper Babe Oiler (Spoit)
Code AW AH
DV-NC55S/H DV-NC60H
8-3. FUNCTION OF MAJOR MECHANICAL PARTS (TOP VIEW)
15
17
10
18
14 1 9 2
11
7
5
3
12 8
16 6
No.
13
4
Function
No.
Function
1
Full erase head
11
Reverse guide lever ass’y
2
Supply pole base ass’y
12
Casecon drive gear
3
Tension arm ass’y
13
Take-up reel disk
4
Idler wheel ass’y
14
Pinch roller lever ass’y
5
Pinch drive lever ass’y
15
Drum ass’y
6
Supply reel disk
16
Loading motor
7
Supply main brake ass’y
17
Drum motor
8
Take-up main brake ass’y
18
Take-up pole base ass’y
9
Pinch drive cam
10
A/C Head ass’y
17
DV-NC55S/H DV-NC60H
FUNCTION OF MAJOR MECHANICAL PARTS (BOTTOM VIEW)
21 22 19
26
20
12
23
No.
Function
24
No.
Function
19
Slow brake
23
Clutch lever
20
Master cam
24
Limiter pulley ass'y
21
Capstan D.D. motor
12
Casecon drive gear
22
Reel belt
26
Shifter
18
DV-NC55S/H DV-NC60H
8-4. DISASSEMBLING THE MECHANISM/MAIN PWB ASSEMBLY 2. Removing the mechanism and cassette housing. Remove 2 screws 3 fixing the cassette housing to the mechanism, and remove the cassette housing.
1. When removing the mechanism from the main PWB. Remove the PWB bottom plate 1 screw 1. Remove the FFC cable (AA, AD, AH) 2 which connecting the PWB and the mechanism. Take out vertically the mechanism so that it does not damage the adjacent parts.
3
Tuner MECHANISM CHASSIS
AUDIO/VIDEO PWB
2 CASSETTE HOUSING
MAIN PWB
1
19
DV-NC55S/H DV-NC60H
8-5. CARES WHEN REASSEMBLING cassette housing. (Conditions: When mechanism and PWB have been installed)
INSTALLING THE CASSETTE HOUSING When the cassette housing is installed on the mechanism, the initial setting is essential condition. There are two initial setting methods, namely electrical and mechanical. 1. Electrical initial setting So as to perform initial setting of mechanism execute the Step 1 of Installation of cassette housing. After ascertaining the return to the initial setting position (*1) install the
2. Mechanical initial setting Feed the pulley feed gear of loading motor with screw driver. After ascertaining the return to the initial set position (*1) install the cassette housing in the specified position. (This method is applied only for the mechanism.)
Pulley feed gear Casecon drive gear
Screwdriver
Drive angle of cassette housing
Tilt mark (*1)
INSTALLING THE MECHANISM ON PWB Lower vertically the mechanism, paying attention to the mechanism edge, and install the mechanism with due care so that the parts are not damaged. So as to fix the mechanism to the main PWB install 1 screw 1. For other, fix the vicinity of loading motor and solder joint side of main PWB.) Connect again the FFC cable (AA-MH, AD-ME, AH-MH) between the mechanism and the main PWB.
PARTS WHICH NEED PARTICULAR CARE When installing the mechanism chassis on the PWB unit, take care so as to prevent deformation due to contact of mechanism chassis with REC TIP SW.
TUNER AUDIO/VIDEO PWB
END SENSOR
REC TIP SW
MAIN PWB START SENSOR
1
20
DV-NC55S/H DV-NC60H
8-6. REMOVING AND INSTALLING THE CASSETTE HOUSING
Notes: 1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care. 2. Misengagement of teeth of casecon drive gear and drive angle gear causes malfunction. (The cassette cannot be set, load and ejection are repeated). 3. In the case when you use the magnet screw driver, never approach the magnet driver to the A/C head, FE head, and drum. 4. When installing or removing, take care so that the cassette housing control and tool do not contact the guide pin or drum. 5. After installing the cassette housing control once perform cassette loading operation.
• Removal 1. In the cassette removing mode, remove the cassette. 2. Unplug the power cord. 3. Remove in the following numerical order. a) Remove two screws 1. b) Slide and pull up the cassette housing control.
1
8-7. TO RUN A TAPE WITHOUT THE CASSETTE HOUSING CONTROL ASSEMBLY 1. 2. 3. 4.
Cassette housing control
5. 6. 7. 8. 9. 10.
Remove the full-surface panel. Short-circuit between TP5102 and TP5103. Plug in the power cord. Turn off the power switch. (The pole bases move into U.L.position.) Open the lid of a cassette tape by hand. Hold the lid with two pieces of vinyl tape. Set the cassette tape in the mechanism chassis. Stabilize the cassette tape with a weight (500g) to prevent floating. Turn on the power switch. Perform running test.
Figure 8-1. • Reassembly 1. Before installing the cassette housing control, shortcircuit between TP5102 and TP5103 provided goes left at VCR display PWB, press the eject button. The casecon drive gear turns and stops when the positioning mark appears. Engage two teeth of casecon drive gear with the three teeth of casecon drive angle gear, and set on the mechanism chassis as shown below.
500g
Weight to prevent float (500g)
Mechanism chassis
Figure 8-3. Casecon drive gear
Note: The weight should not be more than 500g.
Casecon drive angle gear
To take out the cassette tape. 1. Turn off the power switch. 2. Take out the cassette tape.
Figure 8-2. 2. Install in the reverse order of removal. Power source plug is pulled out after the mounted completion, and it comes.
21
DV-NC55S/H DV-NC60H
8-8. REEL DISK REPLACEMENT AND HEIGHT CHECK
Notes: 1. When installing the reel disk, take due care so that the tension band ass'y is not deformed and grease does no adhere. 2. Do not damage the Supply main brake ass'y. Be careful so that grease does not adhere to the brake surface.
• 1. 2. 3. 4.
Removal Remove the cassette housing control assembly. Pull the tension band out of the tension arm ass'y. Remove the Supply/Take-up main brake ass'y. Open the hook at the top of the reel disk, and remove the reel disk. Note: Take care so that the tension band ass'y and main brake ass'y (especially soft brake) are not deformed.
• Reassembly (Take-up reel disk) 1. Clean the reel disk shaft and apply grease (SC-141) to it. 2. Align the phase of the reel disk to that of the reel relay gear and to install a new take-up reel disk onto the shaft. 3. Check the reel disk height and reassemble the take-up main brake ass'y. Note: 1. Take care so that the Take-up main brake ass'y is not damaged. Take care so that grease does not adhere the brake surface. 2. After reassembly, check the video search rewind back tension (see 8-13), and check the brake torque (see 817).
Tension arm ass'y
Take-up main brake ass'y Supply main brake ass'y
Tension band ass'y
• Height checking and adjustment Note: 1. Set the master plane with due care so that it does not contact the drum. 2. When putting the master plane, shift the reverse guide a little in the loading direction. Care must be taken since excessive shift results in damage.
Take-up reel disk
Supply reel disk
Master plane Reverse guide
Figure 8-4.
Supply reel disk Cassette lock release shaft
Note: When the tension band ass'y is pressed in the direction of the arrow for removal, the catch is hard to be deformed.
Position pin
Take-up reel disk
Figure 8-6. Note: 1. Check that the reel disk is lower than part A but higher than part B. If the height is not correct, readjust the reel disk height by changing the poly-slider washer under the reel disk.
Figure 8-5. • Reassembly (Supply reel disk) 1. Clean the reel disk shaft and apply grease (SC-141) to it. 2. Match the phases of reel disk and reel relay gear, and set the new reel disk. 3. After checking the reel disk height, wind the tension band ass'y around the reel disk, and insert into the hole of tension arm ass'y. 4. Assemble the Supply main brake ass'y. 22
DV-NC55S/H DV-NC60H Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow longtime measurement.
2. Whenever replacing the reel disk, perform the height checking and adjustment. Reel disk height adjusting jig
Master plane
10 ± 0.2mm
8-10.CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN REWIND MODE
Mechanism chassis
Reel disk
• Remove the cassette housing control assembly. A
B
• After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord.
Reel disk
Figure 8-7.
• Setting 1. Set a torque gauge to zero on the scale. Place it on the supply reel disk. 2. Press the rewind button. 3. To calculate the remaining capacity, slowly rotate the take-up reel disk, and then shift it into the rewind mode.
8-9. CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN FAST FORWARD MODE • Remove the cassette housing control assembly. • After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord.
• Checking 1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CCW direction. 2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).
• Setting 1. Set a torque gauge to zero on the scale. Place it on the take-up reel disk. 2. Press the FF button. 3. To calculate the remaining capacity of the play back mode, slowly rotate the supply reel disk, and then shift it into the forward mode.
Torque gauge
30mN·m (306gf·cm) or more
• Checking 1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CW direction. 2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).
CCW
The gauge is held at its maximum value. (Red mark)
Torque gauge
Supply reel disk CW
30mN·m (306gf·cm) or more
The gauge is held at its maximum value. (Red mark)
Idler ass'y
Figure 8-9. • Adjustment 1. If the rewind winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, rewind again, and check the winding-up torque. 2. If the winding-up torque is still out of range, replace the drive belt.
Idler ass'y
Figure 8-8. • Adjustment 1. If the FF winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, and check again. 2. If the torque is less than the set value, replace the reel belt.
23
DV-NC55S/H DV-NC60H Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow longtime measurement.
8-12.CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN VIDEO SEARCH REWIND MODE
8-11.CHECKING AND ADJUSTMENT OF TAKE-UP TORQUE IN RECORD/ PLAYBACK MODE
• After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord.
• Remove the cassette housing control assembly.
• Remove the cassette housing control assembly. • After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord. • Turn off the power switch. • Open the cassette torque meter lid, and fix it with tape. • Load the cassette torque meter into the unit. • Put the weight (500g) on the cassette torque meter. • Turn on the power switch. • Press the picture record button, and set EP picture record mode (x3).
• Setting Press the playback button and rewind button to set the video search rewinding mode. • Checking Place the torque gauge on the supply reel disk, and turn it counterclockwise very slowly (one rotation every 1 to 2 seconds) and check that the torque is within the set value 14.0 ± 3.9mN⋅m. (144 ± 40gf⋅cm) Torque gauge
Set value EP6.9 ± 2.5mN⋅m (70 ± 25gf⋅cm)
CCW
500g
Cassette torque meter Supply reel disk
Figure 8-10. • Checking 1. Make sure that value is within the setting 6.9 ± 2.5mN·m (70 ± 25gf·cm). 2. The winding-up torque fluctuates due to variation of rotation torque of limiter pulley ass'y. Read the center value of fluctuation as setting. 3. Set the EP record mode (x3) and make sure that the winding-up torque is within setting.
Figure 8-11.
Note: Surely put the torque gauge on the reel disk to measure. If the torque gauge is raised, accurate measurement is impossible. • Adjustment If the rewinding playback winding-up torque is not within the setting, replace the limiter pulley assembly.
• Adjustment If the playback winding-up torque is not within the setting, replace the limiter pulley assembly. Note: When the torque cassette is set, put a weight (500g) to prevent rise. When the cassette torque meter is taken out. Turn off the power switch.
Note: The winding-up torque fluctuates due to variation of rotation torque of supply reel disk. Read the center value of fluctuation as setting.
24
DV-NC55S/H DV-NC60H
8-13.CHECKING THE VIDEO SEARCH REWIND BACK TENSION • Remove the cassette housing control assembly. • After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord.
Tension gauge 8.8~11.8N (900 ~ 1,200gf)
Pinch roller
• Checking 1. After pressing the play button, press the rewind button, and set the video search rewind mode. 2. Place the torque gauge on the take-up reel disk, and turn it counterclockwise very slowly (one rotation every 2 to 3 seconds) and check that the torque is within the set value 3.4 ± 1.5mN⋅m (35 ± 15gf⋅cm).
Capstan shaft Tension gauge adapter
Figure 8-13.
Torque gauge
1. Detach the pinch roller from the capstan shaft. Do not separate excessively. Or the pinch lever and pinch double action lever may disengage. 2. Engage the tension gauge adapter with the pinch roller shaft, and pull in the arrow direction. 3. Gradually return the pinch roller, and measure the pulling force when the pinch roller contacts the capstan shaft. 4. Make sure that the measured value is within setting 8.8 N to 11.8 N (900 to 1,200gf).
CCW
Take-up reel disk
8-15.CHECKING AND ADJUSTMENT OF TENSION POLE POSITION • Remove the cassette housing control assembly.
Figure 8-12.
• After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord.
Notes: Set the torque gauge securely on the take-up reel disk. If it is not secure, the measurement will be incorrect.
• Turn off the power switch.
8-14.C H E C K I N G T H E P I N C H R O L L E R PRESSURE
• 1. 2. 3. 4. 5.
• Remove the cassette housing control assembly. • After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord.
Setting Open the cassette tape (E-180), and fix with tape. Set the cassette tape in loading state. Put the weight (500g) on the cassette tape. Turn on the power switch. Make the adjustment with the beginning of a E-180 tape. (E-180)
• Checking Press the play button to set the playback mode.
500g
Weight to prevent float (500g)
Figure 8-14.
25
DV-NC55S/H DV-NC60H • Checking 1. Set a cassette tape, push the REC button to place the unit in the SP record mode. Now check the tension pole position. 2. Visually check to see if the right edge of the tension pole is within the 2.3 ± 0.25 from the right edge of the Sup guide shaft.
Tension pole adjuster adjusting range Tension pole adjuster
90°
Sup guide shaft Tension pole
90° 2.3 ± 0.25
Figure 8-18. Make the adjustment with the beginning of a E-180 tape.
Adjust so that the delta mark of tension pole adjuster is within 90° range (left, right).
Figure 8-15. At left side from the center line
8-16.CHECKING AND ADJUSTMENT OF RECORD/PLAYBACK BACK TENSION • Remove the cassette housing control assembly. • After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord. • Turn off the power switch.
2.3 ± 0.25
• 1. 2. 3. 4.
Figure 8-16. Insert the slotted screwdriver in the tension pole adjuster, and rotate counterclockwise.
Setting Open the torque cassette meter and fix with tape. Set the cassette tape in loading state. Put the weight (500g) on the cassette torque meter. Turn on the power switch.
At right side from the center line
500g
Weight to prevent float (500g) Cassette torque meter
2.3 ± 0.25
Figure 8-19. Figure 8-17. • Checking 1. Push the REC button to place the unit in the SP record mode. 2. At this time ascertain that the back tension is within the setting (36.5 to 52g·cm) by seeing the indication of torque cassette meter.
Insert the slotted screwdriver in the tension pole adjuster, and rotate clockwise.
26
DV-NC55S/H DV-NC60H • Checking the brake torque at the take-up side
• Adjustment 1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A. 2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B. A
Torque gauge
Tension arm B
CW
CCW
Take-up reel disk
Tension spring
Figure 8-20.
CCW: 4.9~13.7mN⋅m (50~140gf⋅cm) CW: 3.9~10.8mN⋅m (40~110gf⋅cm)
8-17. CHECKING THE BRAKE TORQUE • Checking the brake torque at the supply side
Figure 8-22. • Remove the cassette housing control assembly.
Torque gauge CCW
• After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord.
CW
• 1. 2. 3.
Supply reel disk
• Checking 1. Turn the torque gauge at a rate of about one turn/2 sec in the CCW direction/CW direction so that the reel disk and torque gauge pointer rotates at equal speed and make sure that the value is within the setting (CCW direction: 4.9 to 13.7mN·m (50 to 140gf·cm), CW direction: 3.9 to 10.8 mN·m (40 to 110gf·cm).
CCW: 2.9~9.8mN⋅m (30~100gf⋅cm) CW: 4.9~13.7mN⋅m (50~140gf⋅cm)
Figure 8-21. • Remove the cassette housing control assembly. • After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord. • 1. 2. 3.
Setting Switch from the FF mode to the STOP mode. Disconnect the power cord. Set a torque gauge to zero on the scale. Place it on the take-up reel disk.
2. Adjustment of the brake torque at the supply side and the take-up side • Unless the supply side brake torque or take-up side brake torque is within the setting, clean the felt surface of reel disk (supply, take-up) brake lever, check again the brake torque. • If value cannot be set within the setting yet, replace the main brake ass'y or main brake spring.
Setting Switch from the FF mode to the STOP mode. Disconnect the power cord. Set a torque gauge to zero on the scale. Place it on the supply reel disk.
• Checking Turn the torque gauge at a rate of about one turn/2 sec in the CW direction/CCW direction with respect to the supply reel disk so that the reel disk and torque gauge pointer rotate at equal speed, and make sure that the value is within the setting (CW direction: 4.9 to 13.7mN·m (50 to 140gf·cm); CCW direction: 2.9 to 9.8mN·m (30 to 100gf·cm).
27
DV-NC55S/H DV-NC60H 3. Align the left end of gear of A/C head arm with the punched mark of chassis, tentatively tighten the screws 1 and 2 so as to ensure smooth motion of A/C head arm. Tentative tightening torque must be 0.15 to 0.20 N·m (1.5 to 2.0kgf·cm).
8-18. REPLACEMENT OF A/C (AUDIO/CONTROL) HEAD 1. Remove the cassette housing control assembly. 2. In unloading state unplug the power cord. • Removal 1. Remove the screws 123, Azimuth screw, Tilt screw. 2. Unsolder the PWB fitted to the A/C head. Notes: 1. When replacing, never touch the head. If you touched, clean with the cleaning liquid. 2. When removing the screw 3, take care so that the spring may out.
1 Tilt screw Azimuth screw 3
Height screw
3 Tilt screw
2
Azimuth screw
Left end of A/C head arm gear Punched line mark on chassis
Figure 8-25. Note: 1. If the screws 1 and 2 are tighten tentatively too loose, the azimuth and height of A/C head may change when they are finally tightened. Therefore care must be taken. 2. After completion of A/C head be sure to adjust tape running. (Execute the running adjustment by the method described in 8-21.)
Height screw 1
Spring
2
Figure 8-23.
• Replacement 1. Solder the removed PWB to the new head assembly. 2. Adjust the height from the A/C head plate (lower surface) to the A/C head base to 10.8mm with slide calipers. (3 places of azimuth screw section, tilt screw section and A/ C head front section) (See the figure below.) Solder New A/C head ass'y A/C head PWB *Never touch the head A/C head base
10.8mm
10.8mm
Figure 8-24.
28
DV-NC55S/H DV-NC60H
8-19.A/C HEAD HEIGHT ROUGH ADJUSTMENT
8-20.HEIGHT ADJUSTMENT OF REVERSE GUIDE
• Setting Azimuth screw
1. Adjust the height from the mechanism chassis to the reverse guide lower flange to 13.38 mm, using the reverse guide height adjustment jig, in tape loading state. (Refer to Figure 8-28 (a) (b).) Reverse guide Reverse guide height adjusting jig
Height screw
Reverse guide height adjusting jig
Tilt screw
Cassette tape
Mechanism chassis
13.38mm
(b)
(a) Figure 8-28.
500g
Weight to prevent float (500g)
2. Rotate counterclockwise the reverse guide height adjustment nut 1/10 turn. (For height adjustment use the reverse guide height adjustment box driver (JiGDRiVER 11055)).
Mechanism chassis
Figure 8-26.
Box driver CCW
1. 2. 3. 4.
Turn off the power switch. Set the cassette tape in the unit. Turn on the power switch. Press the PLAY button to put the unit in the playback mode. 5. Roughly adjust the height of the A/C head by turning the height screw until the tape is in the position shown below.
Height adjusting nut
A/C head
Figure 8-29.
Tape
3. Set the tape, and check for tape crease near the reverse guide in the playback mode. If crease is found, turn the reverse guide adjustment nut to remove crease. (As for crease check refer to Figure 830.)
0.3mm
Figure 8-27. • Adjustment Adjust the height screw visually so that the control head is visible 0.3mm below the bottom of the tape.
A
Capstan motor shaft Fixing guide
500g
Weight to prevent float (500g)
Mechanism chassis Reverse guide
An example of crease near the reverse guide
* Check for crease from the A direction. Figure 8-30.
29
DV-NC55S/H DV-NC60H Notes: 1. Previously set the tracking control in the center position, and adjust the ATR signal waveform to maximum with X value adjustment nut. Thereby the tape run rough adjustment is facilitated. 2. Especially the outlet side ATR signal waveform must have higher flatness.
8-21. ADJUSTMENT OF TAPE DRIVE TRAIN 1. Tape run rough adjustment 1 Remove the cassette housing control assembly. 2 After short-circuiting between TP5102 and TP5103 provided goes left at VCR display PWB, plug in the power cord. 3 Check and adjust the position of the tension pole. (See 8-15.) 4 Check and adjust the video search rewind back tension. (See 8-13.) 5 Connect the oscilloscope to the test point for PB CHROMA signal output (TP1201). Set the synchronism of the oscilloscope to EXT. The PB CHROMA signal is to be triggered by the head switching pulse (TP1202). 6 Set the alignment tape (VROCPSV) to play. (Put a 500g weight on the cassette tape to prevent lift of cassette tape.)
Figure 8-32. 2. Adjustment of A/C head height and azimuth 1 Perform the initial setting of A/C head position by the method stated in "8-18 Replacement 3". 2 Connect the oscilloscope to the audio output terminal. 3 Using the alignment tape in which 1 kHz linear audio signal has been recorded, adjust the height screw so as to get max audio output. 4 Using the alignment tape in which 6 kHz linear audio signal has been recorded, adjust the azimuth screw so as to get max audio output. 5 The adjustment of 3 and 4 twice or three times repeat, and finally adjust 4.
Guide roller Cassette Tape
500g
Weight of 500g
Figure 8-31. 7 Press the tracking button (+), (–) and change the ATR signal waveform from max to min and from min to max. At this time make sure that the ATR signal waveform changes nearly parallel. 8 Unless the ATR signal waveform changes nearly parallel, adjust the height of supply side and take-up side guide roller so that the envelope waveform changes nearly parallel. (For ATR signal adjustment procedure refer to Figure 8-35.) 9 Turn the tilt screw to remove the tape crease at the fixing guide flange. Playback the tape and check for tape crease at the fixing guide flange. (1) If there is no tape crease Turn the tilt screw clockwise so that tape crease appears once at the flange, and then return the tilt screw so that the crease disappears. (2) If there is tape crease Turn counterclockwise the tilt screw so that the tape crease disappears. (Reference) If the tilt screw is turned clockwise crease appears at the lower flange.
For X value adjustment Adjust the X value, turning the geartype screwdriver.
Figure 8-33. 3. Tape run adjustment 1 Connect the oscilloscope to PB CHROMA signal output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switching pulse). 2 Rough adjustment of X value Tentatively fix A/C head arm screws 1 and 2 by the method described in 8-18 "Replacement 3". Playback the alignment tape (VROCPSV) and shortcircuit between TP5101 and TP5103. As a result the auto-tracking is automatically cancelled, so that the X value adjustment mode is set. Move the A/C head with the X value adjustment gear driver (JiGDRiVER-6) by the method shown in Figure 8-33, and adjust the A/C head so as to get the maximum ATR signal waveform. (Note: When the A/ C head is adjusted, adjust so that the maximum ATR signal waveform is obtained nearest the position of initial setting made in 8-18.) 30
DV-NC55S/H DV-NC60H 3 Next, press the tracking button (+), (–) and change the ATR signal waveform from max to min and from min to max. At this time adjust the height of supply and take-up side guide roller with the adjustment driver (JiGDRiVER-4) so that the ATR signal waveform changes nearly parallel. 4 If the tape is lifted or sunk from the helical lead surface, the PB CHROMA signal waveform appears as shown in Figure 8-35. 5 Press the tracking button (+), (–) and make sure that the ATR signal waveform changes nearly parallel. 6 Finally check tape crease near the reverse guide. If tape crease is found, remove it as stated in 8-20 "HEIGHT ADJUSTMENT OF REVERSE GUIDE" item 3.
PB CHROMA Signal
Head switching pulse Figure 8-34. 4. A/C head X value adjustment 1 Tentatively fix A/C head arm screws 1 and 2 by the method described in 8-18 "Replacement 3". 2 Playback the alignment tape VROCPSV, and shortcircuit between TP5101 and TP5103. As a result the auto-tracking is automatically cancelled, so that the X value adjustment mode is set.
When the tape is above the helical lead. Supply side
Adjustment
Supply side guide roller rotated in clockwise direction (lowers guide roller) to flatten ATR signal.
Take-up side
Take-up side guide roller rotated in clockwise direction (lowers guide roller) to flatten ATR signal.
When the tape is below the helical lead. Supply side
Take-up side
Supply side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The supply side guide roller is then rotated in the clockwise direction to flatten the ATR signal.
Take-up side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The take-up side guide roller is then rotated in the clockwise direction to flatten the ATR signal.
Figure 8-35. 3 Move the A/C head with the X value adjustment gear driver by the method shown in Figure 8-33, and adjust the A/C head so as to get the maximum ATR signal waveform. (Note: At this time adjust so as to get the maximum ATR signal waveform nearest the A/C head position which has been set in case of X value rough adjustment as stated in 8-21, 3- 2.) 4 Tighten finally the screws 1 and 2. Be sure to tighten at first the screw 1 and then the screw 2. Final tightening torque is 0.6N·m (If the screw 2 is tightened first, the X value may deviate.) 5 Adjust the playback switching point (Refer to the electric adjustment method.) 6 Playback the self-picture-recorded tape, and check the flatness of ATR signal waveform and sound.
Notes: When the A/C head X value adjustment is performed, be sure to perform at first X value rough adjustment (refer to 821, 3-2). 1 2
Figure 8-36.
31
DV-NC55S/H DV-NC60H
8-23. REPLACEMENT OF DRUM D.D. MOTOR
8-22.REPLACEMENT OF THE CAPSTAN D.D. (DIRECT DRIVE) MOTOR
1. Set the ejection mode. 2. Withdraw the main power plug from the socket.
• Remove the mechanism from the main PWB (refer to 84 item 1 When removing the mechanism from the main PWB ).
• 1. 2. 3. 4. 5.
• Removal (Follow the order of indicated numbers.) 1. Remove the reel belt 1. 2. Remove the slow brake lever 2. 3. Remove the three screws 3.
Notes: 1. In removing the D.D. stator assembly, part of the drum earth spring pops out of the pre-load collar. Be careful not to lose it. 2. Install, so that the D.D. rotor ass'y and upper drum ass'y mounting direction check holes align. (Align the upper drum dent with the rotor hole.) 3. Be careful not to damage the upper drum or the video head. 4. Protect the hole elements from shock due to contact with D.D. stator or D.D. rotor ass'y. 5. After installation adjust the playback switching point for adjustment of servo circuit.
3
Capstan D.D. motor control PWB
Capstan D.D. motor
Removal (Perform in numerical order.) Disconnect the FFC cable 1. Unscrew the D.D. stator assembly fixing screws 2. Take out the D.D. stator assembly 3. Unscrew the D.D. rotor assembly fixing screws 4. Take out the D.D. rotor assembly 5.
2
1 Reel belt
Figure 8-37.
2 Slow Blake Lever
D.D. stator ass'y 3
• Reassembly 1. Taking care so that the capstan shaft does not contact the mechanism chassis, set its position on the mechanism chassis, and then install with the three screws 3. 2. Install the slow brake lever 2. 3. Install the reel belt 1.
1
4
FFC
4
5
D.D. rotor ass'y
Notes: 1. Before installing the capstan D.D. motor, confirm whether an acetate tape (ZTAPEN120020E) is drawn on the back of mechanism chassis.
Upper drum
Stick an acetate tape on the projection part of the chassis.
Figure 8-39.
Capstan Motor Installation position.
Mechanism Chassis from the back.
Figure 8-38. 2. After installing the capstan D.D. motor, be sure to rotate the capstan D.D. motor and check the movement. 3. Set the tape, and check for the tape crease near the reverse guide in the playback mode. Adjust the A/C head and azimuth as stated in 8-21 item 2. If crease is found, adjust as stated in 8-21 item 3.
32
DV-NC55S/H DV-NC60H
8-24.REPLACING THE UPPER AND LOWER DRUM ASSEMBLY
8-25.ASSEMBLING OF PHASE MATCHING MECHANISM COMPONENTS • Assemble the phase matching mechanism components in the following order. 1. Assemble the pinch roller assembly and pinch drive cam. 2. Mounting the shifter (on the back of the mechanism chassis). 3. Mounting the master cam (on the back of the mechanism chassis). 4. Assemble the connection gear, slow brake and loading motor parts.
• Replacement (Perform in the numerical order) 1 Remove the motor as stated in 8-23 D.D. motor replacement. 2 Remove the drum earth brush ass’y 2. 3 Remove the drum base 3 from the upper and lower drum assembly 1.
[Cares when replacing the drum] 1. Be careful so that the drum earth brush is not lost. 2. Do not touch directly the drum surface. 3. Fit gently the screwdriver to the screws. 4. Since the drum assembly is an extremely precise assembly, it must be handled with utmost care. 5. Make sure that the drum surface is free from dust, dirt and foreign substances. 6. After replacing the drum be sure to perform the tape running adjustment. After that, perform also the electrical adjustment. • Playback switching point adjustment • X-position adjustment and check • Standard and x-3 slow tracking adjustment 7. After replacing the drum clean the drum.
• PINCH DRIVE CAM AND PINCH ROLLER ASSEMBLING METHOD. (Place the following parts in position in numerical order.) (1)Reverse drive lever 1 (2)Reverse guide spring 2 (3)Reverse guide lever ass’y 3 (4)Reverse guide height adjusting nut 4 (5)Pinch drive cam 5 (6)Pinch roller ass’y 6 7 (7)Open lever 7
6
2 4
1
3 1 2
5
3
Figure 8-41. Figure 8-40.
33
DV-NC55S/H DV-NC60H 1Insert Reverse Guide Lever Ass’y Insert reverse guide lever ass'y
2 Insert pinch drive cam
Align here.
Turn the reverse guide lever assembly counterclockwise to the stopper.
Fit the pinch drive cam so that the notch of pinch drive cam aligns with the dent of pinch drive lever assembly.
Fit the pinch drive cam so that the notch of pinch drive lever assembly aligns with the half-round notch of chassis. Pinch drive lever ass'y
Figure 8-42-1.
2Insert Pinch Roller/Pinch Double Action Lever Ass’y.
3Insert Open Lever.
Pinch Roller Double Action Lever Ass'y
Open lever
Phase Matching Point 2
Figure 8-42-2.
Figure 8-42-3. 34
1.
8-26. INSTALLING THE SHIFTER
2. Drum
3.
Capstan D.D. motor
4.
DV-NC55S/H DV-NC60H Make sure that the loading gear is at the Phase-Matching point 1 as shown below. Install, paying attention to insert point 5 and release point 3. For the phase matching at the insert point 1, see the Phase-Matching point 2 as shown below. Finally fix the inserts 1 and 4.
Reel pulley
Phase-Matching point 2
(Bottom side of mechanism chassis)
Figure 8-43.
Loading gear (T) Insert point 1
Round mark
Shaft 1
Sifter
Half round notch Insert point 3
Insert point 2
Insert point 4
Shaft 1
Rotation point 2 Shaft 2
Release point 3
Shaft 1 Phase-matching point 1
Figure 8-44.
35
Insert point 5
DV-NC55S/H DV-NC60H
8-27.INSTALLING THE MASTER CAM (AT REAR SIDE OF MECHANISM CHASSIS)
8-28. REPLACEMENT OF LOADING MOTOR • Removal
1. Make sure beforehand that the shifter is at the point as shown below. 2. Place the master cam in the position as shown below.
E ring (XRESJ30-06000) Master cam
Apply grease Apply grease
Fully turn clockwise
Fully turn counterclockwise Face the wide tooth side ward
No grease
Figure 8-45-1.
Note: See the figure below for the phase matching between the master cam and the casecon drive gear. 3. Finally fix with the E ring.
Figure 8-46.
Master cam
Casecon drive gear
• Replacement Remove the loading motor, and install the replacement loading motor as shown below.
Half-round notch Round mark
10.2 +0.2 –0.2 mm
When installing the master cam, align the casecon drive gear round mark with the half-round notch of master cam.
Figure 8-45-2.
Figure 8-47. The loading motor pressing-in must be less than 147 N (15 kgf). Adjust the distance between motor and pulley to 10.2 +0.2 –0.2 mm).
36
DV-NC55S/H DV-NC60H
8-29. ASSEMBLY OF CASSETTE HOUSING 1. Drive Gear and R Drive angle ass’y
MSPRT0381AJFJ
Apply grease Apply grease
Apply grease
Figure 8-48.
2. Synchro Gear, Drive Gear L and Drive Gear R LANGF9592AJFW
Top surface should be free from scratches or soil.
Drive angle
Drive gear R
Frame
Figure 8-49.
37
DV-NC55S/H DV-NC60H
9. ELECTRICAL ADJUSTMENT Notes: • Before the adjustment: Electrical adjustments discussed here are often required after replacement of electronic components and mechanical parts such as video heads. Check that the mechanism and all electric components are in good working condition prior to the adjustments, otherwise adjustments can not be completed. • Instruments required: Colour TV monitor Dual-trace oscilloscope Alignment tape (VROCPSV) Blank video cassette tape DC voltmeter Screwdriver for adjustment Servicing precations When the IC705 (E2PROM) has been replaced, make the following reprogramming. Depending on models, the IC705 (E2PROM) has been factry-adjusted for it’s memory function. It’s therefore necessary to reprogram the memory function for the model in question. Note that the servo circuit requires readjustments for the head switching point, slow and still modes. • Location of controls and test points
TU1401
TERMINAL
AV
P201
POW
VCR Mechanism
TP5102
DVD
TP5101
Figure 9-1.
38
DV-NC55S/H DV-NC60H
SERVO CIRCUIT ADJUSTMENT ADJUSTMENT OF HEAD SWITCHING POINT Measuring instrument
Dual-trace oscilloscope Colour TV monitor
Mode
Playback
Cassette
Alignment tape (VROCPSV)
Test point
Pin(2) of P201 (H.SW.P.) to CH-1, VIDEO OUT jack to CH-2 (CH-1 trigger slope switch at (+), Internal trigger at CH-1 side.)
Specification
CH-1: 1V/div 50µs/div CH-2: 2V/div 50µs/div
CH-2 VIDEO OUT
CH-1 HEAD SWITCHING PULSE
6.5 ± 0.5H (lines)
V-sync.
Figure 9-2.
ADJUSTMENT OF PAL SYSTEM SP/LP/EP SLOW TRACKING PRESET
6.5 ± 0.5H (lines)
1. Remove the front panel and play the alignment tape. (VROCPSV) 2. Press the PLAY button. (Playback picture on the monitor screen.) 3. Make for a moment short-circuit TP5101-TP5103, located at the left side on the VCR display PWB. Be sure that all the fluorescent display tubes light up into the TEST mode.(See Note below) Be sure the "PLAY" appears in the fluorescent display tubes flashing (about 1Hz) into the auto PG adjustment operating. Note: When the manual PG adjustment, obseve the waveform with an oscilloscope and make adjustment FF or REW button so that the specification. 4. Stop the "PLAY" appears in the flashing of fluorescent display tubes at adjusted. 5. Press the STOP button in the return to normal mode. 6. Make this checking of waveform on the oscilloscope screen be as shown in Figure 9-2. just after the head switching point have been adjusted. Note: 1 Set-up of TEST mode. When the adjustment of HEAD SWITCHING POINT, AUTO TRACKING function is invalid. 2 When the cassette housing control ass’y is removed, set-up of mechanism operating mode. 1) Replug the AC power cord it a few minutes later. 2) Make a short-circuit TP5102-TP5103 located at the front side on the main PWB, and press both tracking control button at the same time to set the tracking in center. 3) AC power cord is plugged in. 4) You can mechanism operatig mode, Replug the AC power cord a few minutes later.
Measuring instrument
Colour TV monitor
Mode
Playback
Cassette
Self-recorded tape (SP/LP/EP mode)(See Note below)
Control
Tracking control buttons (+) or (–)
Specification
Minimized noise on monitor screen
1. Have the unit to receive a good TV broadcast or feed a video signal to the VIDEO IN jack. (See note 2 below) 2. Set the tape speed in SP mode by using the remote control and record the signal on tape. 3. Rewind and play the tape where signal was recorded in above step. 4. Press the SLOW button on the remote control, and playback the recorded portion in the slow mode. 5. Make for a moment short-ciucuit TP5101-TP5103, located at the front side on the main PWB. Be sure that all the fluorescent display tubes light up into the TEST mode. 6. Look at the monitor screen and adjust the (+) or (–) TRACKING buttons so that the there is noise disappears from the screen. 7. Press the STOP button to return to normal mode. 8. Play the tape a few seconds then press the SLOW button again and make sure there is on noise in the screen.(For the LP/EP mode put adjustment at the same adjustmet way as SP mode.) Notes: 1 Self-recorded tape means a cassette whose program was recorded by the unit being adjusted. 2 The TV program will not be recorded if RCA or 21pin plugs are pluged in to the AUDIO/VIDEO input terminals.
39
DV-NC55S/H DV-NC60H
ADJUSTMENT OF PAL SYSTEM FV(False Vertical Sync) OF STILL PICTURE Measuring instrument
Colour TV monitor
Mode
Playback still
Cassette
Self-recorded tape (SP mode) (See Note below 2)
Control
Tracking control buttons (+) or (–)
Specification
No vertical jitter of picture
1. Play a cassette which was recorded by the unit in SP mode. 2. Press the PAUSE/STILL button to freeze the picture. 3. Look at the monitor screen and adjust (+) or (–) TRACKING buttons so that the vertical jitter of the picture to be minimized. 4. Play and freeze the self-recorded tape in SP mode and make sure vertical jitter of the picture is not noticeable.(For the LP/EP mode put adjustment at the same adjustment way as SP mode.) Note: 1 The FV goes back to the it’s initial state when the unit is put into the system controller reset mode due to power failure, etc. In this case, preset the FV once again. 2 Self-recorded tape is a cassette whose program was recorded by the unit being adjusted.
40
DV-NC55S/H DV-NC60H
10. TEST MODE "NO DISC" state "F0" key input (Press the "play" key and the "stop" key for 5 seconds.) F0000000 00000000 The preparation date display of the program 10000000 ~~~~~~~~ (Last updata) The "playback" key of the remote controller is pushed. Model number display 10000001 00000552 (Model number) The "playback" key of the remote controller is pushed. The version display of the program 10000002 ~~~~~~~~ (Program ver.) The "playback" key of the remote controller is pushed. Reagion number display 10000003 00000002 (Region code:Binary display) The "playback" key of the remote controller is pushed. Micro-code number display Micro-code is the thing of the process 10000004 ~~~~~~~~ (Microcode ver.) program of the system integrated circuit. The "playback" key of the remote controller is pushed. The preparation date display of the servo program 10000005 ~~~~~~~~ (Servo ver.) The "playback" key of the remote controller is pushed. It is returned to the test mode initial image plane. Color bar display 00001 (FIP)
There is no copy guard signal. As for the symptom when it was dubbed in the video tape recorder?
Color bar display 00002 (FIP)
The "playback" key of the remote controller is pushed. AGC only As for the symptom when it was dubbed in the video tape recorder? The "playback" key of the remote controller is pushed. AGC+Color stripe1 As for the symptom when it was dubbed in the video tape recorder?
Color bar display 00003 (FIP)
The "playback" key of the remote controller is pushed. AGC+Color stripe2 As for the symptom when it was dubbed in the video tape recorder?
Color bar display 00004 (FIP)
The "playback" key of the remote controller is pushed. The all FIPs burning 40000000 00000000 (OSD only) The "4" key of the remote controller is pushed. It is returned to the test mode initial image plane.
To (1)
41
DV-NC55S/H DV-NC60H From (1) "3" Key input DYNMIC TEST 30000000 00000000 Laser test mode "1" Key input The tray opens, the DVD laser is lit, spinning is performed and the sled moves to the outer periphery.
LASER TEST 30000001 000000DD "1" Key input LASER TEST 30000001 000000CD
The DVD laser goes out, the CD laser is lit, spinning is performed, and the sled moves to the outer periphery.
"1" Key input LASER TEST 30000001 00000000
The DVD and CD lasers go out, spinning is performed and the sled moves to the outer periphery.
"1" Key input Step execution mode "2" Key input STEP TEST 30000001 00000000
Load a disc after the tray is opened.
"Open/Close" Key input STEP TEST 30000200 00000000
STEP TEST 30000201 00000000
Focus on
"Playback" Key input STEP TEST 30000202 00000000
RF gain adjustment, Track on
"Playback" Key input STEP TEST 30000203 00000000
Focus gain adjustment
"Playback" Key input STEP TEST 30000204 00000000
Track gain adjustment
"Playback" Key input STEP TEST 30000205 00000000
STEP TEST DD000210 00000000
Focus balance adjustment
(DVD operation) In case of 2-layer DVD, adjust the focus balance, the RF gain and the focus gain of the layer 0.
STEP TEST DD000211 00000000
Control data lead
"Playback" Key input STEP TEST END DD000212 ~~~~~~~~ To (2)
Following playback state
(~~~~~~~~ is a sector ID)
42
(CD operation) STEP TEST END CD000210 ~~~~~~~~
Following playback state after reading TOC.
(~~~~~~~~ is a SUB-Q)
DV-NC55S/H DV-NC60H From (2) Following playback, jump test mode "3" Key input PLAY TEST 30000001 00000000
Load a disc after the tray is opened.
"Open/Close" Key input PLAY TEST DD000303 ~~~~~~~~
Following playback state (~~~~~~~~ is a sector ID) Pressing the keys on the remote control mentioned in the table below enables the test jump. Key Jump Key 1 -1 3 4 -102 6 7 -510 9 C -511 M 2 -765 Repeat 5 -766 A-B 8 -7000 Program Before skipping. -15000 After skipping. Next replay Layer Jump
Jump 1 102 510 511 765 766 7000 15000
Spin offset adjustment mode "MENU" Key input SPIN OFFSET
ADJUST COMPLETE 00000000 0000~~~~
Tray open.
(Offset adjustment of the spindle is executed automatically.) The adjustment result is indicated in the ~~~~ section.
[ROM RENEWAL MODE] 1. A DVD itself and a personal computer are articulated as the right figure. Software for the renewal is started more. 2. A power source is put with pushing a DVD's own playback key and a halt key at the same time. (It keeps pushing it for about three seconds.) R : OK
It is displayed.
3. When "Y" is inputted in accordance with the personal computer display and data transfer indication is shown and renewal process is started normally when an ENTER key is pushed. W : STR
It is displayed.
4. When renewal is completed normally. W : END
Personal computer (DOS)
It is displayed.
5. "STOP" key is surely pushed if renewal is completed and the display of above NO.4 is confirmed.It is made to turn off POWER after that. Fixture for the ROM renewal (RUNTK0808GEZZ)
PART CODE RUNTK0808GEZZ
Price Code CD
DIGITAL It is articulated to the OUT terminal connection child.
43
DVD itself
DV-NC55S/H DV-NC60H
11. TROUBLESHOOTING (DVD) FLOW CHART NO.1
FLOW CHART NO.3
The fluorescent display tube does not light. Is the supply voltage of 5V fed to pin(14) and pin (38) of IC5001? Yes Is the supply voltage of -19V fed to pin(27) of IC5001? Yes Is there 500kHz oscillation at pin(44) of IC5001? Yes Check the signal lines of FIP DA, FIP CK, FIP CS of IC5001 and IC504. Yes Are the filament voltage applied between (1), (2) and (31), (32) of the fluorescent display tube? Also negative voltage applied between these pins and GND. Yes Check the fluorescent display tube and its periphery?
No operation is possible from the infrared remote control. No
No
No No
No
Check the PC 5V line.
Check the PC -22V line and Q8202.
Check R5014-5, IC5001 and their periphery. Check or replace IC5001 and IC504.
Operation is possible from the DVD, but no operation is possible from the infrared remote control. Yes Is 5V voltage supplied to the pin(3) terminal of remote control receiver? Yes Is the "L" pulse sent out pin(1) terminal of receiver when the infrared remote control is activated? Yes Is pulse signal supplied to the pin(10) of IC8201?
No
Replace the remote control receiver or replace the remote control transmitter is necessary.
No
Check AT 5V line.
No
Replace the remote control receiver.
No
Check the line between the remote control receiver and the pin(10) of IC8201.
Check the power circuit, D5004 and Q8203.
Yes
Replace IC8201.
No No
Is pulse signal supplied to the pin(32) of IC504?
Check the line between the remote control receiver and the pin(32) of IC504.
Check that the fluorescent display tube is free from damages such as crack.
Yes
FLOW CHART NO.2 The key operation is disabled.
Replace IC504.
FLOW CHART NO.4 No
The disc tray cannot be opened and closed. Replace key switch.
Is the signal from the pins(70) and (69) of IC504 input into the pins(1) and (28) of IC7701? Yes
Is loading motor drive voltage output from the pins(9) and (10) of IC7701? Yes
3.3V OFF
No
No
Check the LD-RVS/FWD signal line between IC7701 and the IC504. Check AT 8V line. No Is 8V voltage applied to the pin(8) of IC7701? Yes Replace IC7701.
2.5V
KEY-1/2
44
Is key switch contact and installation state normal? Yes Is the control voltage normally into the pins(95) and (96) of IC504?
Is the loading motor drive voltage applied to the No terminal of loading motor? Yes Check for mechanism and gear engagement and breakage.
1.8V 0.9V
Check the line between the IC7701 and the loading motor.
FLOW CHART NO.5 0V
S5003 STOP
S5002 PLAY
KEY–1
KEY–2
The [No Disc] indication. (In case of focus error) Does the optical pickup move up and down after the disc is removed?(Checking of symptom.) Yes Is FE signal output to the pin(21) of IC301 when the disc is set? Yes Is FE signal inputted into the pin(150) of IC701? Yes Check or replace IC701. Check the line between the IC301 and IC701.
No
No No
See FLOW CHART NO.6 Replace IC301. Yes Is there input signal on the pins(52), (53), (54) and (55) of IC301? No Check the connection of optical pickup cable. If it is normal, replace the optical pickup.
FLOW CHART NO.6
FLOW CHART NO.9
The [No Disc] indication. (In case focus servo does not function.)
Picture do not operate normally.
Is the focus control signal output from the pin(158) No of IC701? Yes No Is the focus control signal from the pin(158) of IC701 input into the pin(23) of IC7701? Yes
Check the pins(10) and (11) of IC701 periphery circuit. If it is normal, replace IC701. Check the focus control signal line between the IC7701 and IC701. Check AT 8V line.
Is the focus control drive voltage output from the pins(17) and (18) of IC7701? Yes
Is the focus control drive voltage applied to the terminal of focus actuator? Yes Check the connection of optical pickup cable. If it is normal, replace the traverse chassis unit.
No
No
No Is 8V voltage applied to the pin(8) of IC7701? Yes Check the pin(21) of IC7701 and replace IC7701.
Check the line between the IC7701 and the focus actuator.
FLOW CHART NO.7 The [No Disc] indication. (When the laser beam does not light.)
45
Is the Q303(LD POWER CTL) drive output to the pin(46) of IC301? (Checking of symptom.) Yes Is 5V voltage applied to the emitter of Q303? Yes Is approx. 2V applied to the pin(3) of the pickup terminal? (See note.) Yes Check the connection of optical pickup cable. If it is normal, replace the traverse chassis unit.
No No No
Check the line between the pin(46) of IC301 and the base of Q303. Check the A_5V line.
Check the main unit. (IC601, Q201, Q202, Q203 periphery circuit.) Check the PC 5V line.
No
No
No
No
Check the parts C2003, C2007, C2008 and the lines between them.
No Is 5V applied to the pins(1) and (28) of IC2001? Yes Replace IC2001.
Check parts C2016, Q2002 periphery circuit and the line between them. No Is 5V applied to the pin(6) of IC2004? Yes Are the DVD_H line at pin(2) of IC2004 on "L" level? Yes Replace IC2004.
No
Check the DVD_H line.
Note: Since the laser diode is very susceptible to static electricity, be careful of static electricity or electricity leak from the measuring equipment when confirming the voltage.
Both picture and sound do not operate normally.(1)
Replace the main PWB unit. Yes See FLOW CHART NO.9 and NO.10.
No
Check the line between the Q303 and pickup terminal.
FLOW CHART NO.8
Set the disc on the disc tray. Yes Do you have done disk loading by normality? Yes Is the level of RF signal which is output from pins(29), (30) of IC301, normal? Yes
Set the disc on the disc tray. Yes Are the video signals outputted to the pins of main unit connector CN802, CN803? CN803 1PIN CVBS/Y CN802 3PIN Y/CR CN802 5PIN C/CB Yes Are the video signals shown above input into the pins of IC2001? IC2001 2PIN CVBS IC2001 11PIN S-Y IC2001 4PIN S-C Yes Are the video signal outputted to each pins of IC2001? IC2001 27PIN CVBS IC2001 18PIN S-Y IC2001 25PIN S-C Yes Are the CVBS video signal shown above input into the pin of terminal? IC2004 1PIN CVBS Yes Are the video signal outputted into the pin of terminal? IC2004 7PIN CVBS Yes
No No
No
Check the loading switch. Check for contamination of objective lens of optical pickup.
Replace traverse chassis unit.
Are the video signals shown above input into the pins of terminal? IC1206 6PIN CVBS IC1201 6PIN S-Y IC1202 6PIN S-C Yes Are the video signals outputted into the pin of terminal? IC1206 2PIN CVBS IC1201 2PIN S-Y IC1202 2PIN S-C Yes Are the video signals shown above outputted into the pins of output terminal? Are the composite video signals outputted to the VIDEO OUT terminal (J1202)? Are the luminance signals outputted to the S-OUT terminal (J1201)? Are the chroma signals outputted to the S-OUT terminal (J1201)?
No No
Check the line between pin(7) of IC2004 and pin(6) of IC1206. Check C1201, C1206, Q2003, Q2002 periphery circuit and the lines between them.
Is 5V applied to the pin(3) of IC1201, IC1202 and IC1206. Yes Replace IC1201, IC1202 and IC1206.
No
Check the VIDEO OUT terminal (J1202) and the line between the pin(2) of IC1206 and the VIDEO OUT terminal (J1202). Check the S-OUT terminal (J1201) and the line between the pin(2) of IC1201 and the S-OUT terminal (J1201). Check the S-OUT terminal (J1201) and the line between the pin(2) of IC1202 and the S-OUT terminal (J1201).
No No
No
DV-NC55S/H DV-NC60H
No
*1
Sound do not operate normally.
46
Set the disc on the disc tray. Yes Are the digital audio interface signals outputted to the pins of main unit connector CN801? CN801 3PIN AMCLK CN801 4PIN ABCLK CN801 5PIN ALRCLK CN801 6PIN AOUT0 Yes Are the digital audio interface signals inputted to the pins of IC6001? IC6001 5PIN AMCLK IC6001 3PIN ABCLK IC6001 1PIN ALRCLK IC6001 2PIN AOUT0 Yes Are the system control interface signals outputted to the pins of main unit connector CN801? CN801 10PIN ADAC DA CN801 11PIN ADAC CK CN801 12PIN ADAC L CN801 16PIN RSTO I Yes Are the system control interface signals inputted to the pins of IC6001? IC6001 26PIN ADAC DA IC6001 27PIN ADAC CK IC6001 28PIN ADAC L IC6001 22PIN RSTO I Yes Are the audio interface signals outputted to the pins of IC6001? IC6001 16PIN L OUT IC6001 13PIN R OUT Yes
Are the audio interface signals inputted to the pins of IC6004? IC6004 3PIN L OUT IC6004 5PIN R OUT Yes Are the audio interface signals outputted to the pins of IC6004? IC6004 1PIN L OUT IC6004 7PIN R OUT Yes
*1
No
Are the audio interface signals inputted to the pins No of IC6010? IC6010 2PIN L OUT IC6010 12PIN R OUT Yes Are the audio interface signals outputted to the pins of IC6010? No IC6010 15PIN L OUT IC6010 14PIN R OUT Yes
Check the main unit. (IC601 periphery circuit.)
Check the line between the pins of main unit connector CN801 and the pins of IC6001. CN801 3PIN → IC6001 5PIN AMCLK CN801 4PIN → IC6001 3PIN ABCLK CN801 5PIN → IC6001 1PIN ALRCLK CN801 6PIN → IC6001 2PIN AOUT0
No
No
Are the audio interface signals inputted to the pins No of IC6011? IC6011 3PIN L OUT IC6011 5PIN R OUT Yes Are the audio interface signals outputted to the No pins of IC6011? IC6011 1PIN L OUT IC6011 7PIN R OUT Yes Are the audio signals input to the pins of IC2501? No IC2501 2PIN L OUT IC2501 1PIN R OUT Yes
Check the main unit. (IC504 periphery circuit.)
Check the line between the pins of main unit connector CN801 and the pins of IC6001. CN801 10PIN → IC6001 26PIN ADAC DA CN801 11PIN → IC6001 27PIN ADAC CK CN801 12PIN → IC6001 28PIN ADAC L CN801 16PIN → IC6001 22PIN RSTO I
No
Are the audio signals output to the pins of IC2501? No IC2501 42PIN L OUT IC2501 43PIN R OUT Yes Are the audio signals output to the specific outputted terminals? No Is the DVD audio signal (L) output to the AUDIO OUT (L) terminal (J1202)? No Is the DVD audio signal (R) output to the AUDIO OUT (R) terminal (J1202)?
Check the PC 3.3V line and PC 5V line. No Is 3.3V applied to the pin(7) and 5.5V applied to the pins(10), (15) and (19) of the IC6001? Yes Check or replace IC6001.
No
Check the line between the pins of IC6001 and the pins of IC6004. IC6001 16PIN → IC6004 3PIN L OUT IC6001 13PIN → IC6004 5PIN R OUT
No
Check the AUDIO OUT (L) terminal (J1202) and the line between the pin(42) of IC2501 and the AUDIO OUT (L) terminal (J1202). Check the AUDIO OUT (R) terminal (J1202) and the line between the pin(43) of IC2501 and the AUDIO OUT (R) terminal (J1202).
Check the PC 9V line. No Is 9V applied to the pin(8) of IC6004? Yes Check or replace IC6004.
No
*2
*2
*3
Are the audio signals output to the specific outputted terminals? Is the DVD audio signal (L) output to the DVD AUDIO OUT (L) terminal (J1204)? Is the DVD audio signal (R) output to the DVD AUDIO OUT (R) terminal (J1202)?
*3 Check the line between the pins of IC6010 and the pins of IC6004 and the sound mute periphery circuit.(Q6007-8.) IC6004 1PIN → IC6010 2PIN L OUT IC6004 7PIN → IC6010 12PIN R OUT
Is 9V applied to the pin(16) of IC6010? Yes Are the pins(9), (10) and (11) of IC6010 on "L" level? Yes No Replace IC6010. Check the DVD-H line and Q6010. Check the line between the pins of IC6010 and the pins of IC6011. IC6010 15PIN → IC6011 3PIN L OUT IC6010 14PIN → IC6011 5PIN R OUT
Is 9V applied to the pin(8) of IC6011? Yes Replace IC6011.
Is 5V and 12V applied to the pins of IC2501? IC2501 PIN(24) & (29)→ AT5V IC2501 PIN(4) → AT12V Yes No Check the AT5V and AT12V line. Are the ST SCL and ST SDA inputted to the pins (22) and (21) of IC2501 respectively? Yes Is DEC A_Mute at pin(9) of IC2501 LOW? Yes No Replace IC2501.
Check the line between the pins of IC701 and the pins of IC2501 IC701 18PIN → IC2501 22PIN ST SCL IC701 17PIN → IC2501 21PIN ST SDA
No
No
Check the line between the pins of IC2501 and the pins of IC6011 and the sound mute periphery circuit (Q6011-12). IC6011 1PIN → IC2501 2PIN L OUT IC6011 7PIN → IC2501 1PIN R OUT
Check the DEC A_Mute line between pin(96) of IC701 and pin(9) of IC2501.
No
No
Check the DVD AUDIO OUT (L) terminal (J1204) and the line between the pin(16) of IC6001 and the DVD AUDIO OUT (L) terminal (J1204). Check the DVD AUDIO OUT (R) terminal (J1204) and the line between the pin(13) of IC6001 and the DVD AUDIO OUT (R) terminal (J1204).
No
DV-NC55S/H DV-NC60H
FLOW CHART NO.10
FLOW CHART NO.4
(VCR)
A cassette tape is not take in.
FLOW CHART NO.1 The VCR flourescent display tube fails light up. Is the supply voltage of 5V feed to pin(7) of IC5101? YES Is the supply voltage of –20V feed to pin(1) of IC5101? YES Is it possible to confirm signals FIP CS, FIP OE, FIP DATA, and FIP CLK on the pins(2), (3), (4) and (5) of IC5101? YES Are grid and segment signals supplied to the indication tube (DG5101) from the indication tube driver IC (IC5101)? YES Is supply filament voltage feed between pin(1)/(2) and (31)/(32) of the flourescent display tube? YES Check the periphery of fluorescent indication tube and main block.
NO NO NO
NO
NO
NO
Check STBY 5V line. Check STBY –20V line. Check signal line between IC701 and IC5101.
Replace IC5101.
Check power circuit and D9701.
Check that the fluorescent indication tube is free from damages such as crack.
Is "L" level applied at pin(19) of IC701. YES Are start sensor shutter go to openwhen the cassette tape is inserted? YES Does pin(79) of IC701 change from "H" to "L" level when the cassette tape is inserted? YES Does pin(11) of IC7002 go to a "H"(about 4.7V) level when the cassette tape is inserted? YES Does pin(13) of IC7002 change to about 10V when the cassette tape is inserted? YES Is the specified voltage (about 10V) applied at the loading motor terminal when the cassette tape is inserted? YES Replace loading motor.
NO NO
Check R717. Check start sensor shutter.
NO
Check line start sensor and all the way up thru to pin(79) of IC701.
NO
Check line pin(93) of IC701 and all the way up thru to pin(11) of IC7002.
NO
NO
Check IC7002.
Check between IC7002 and loading motor.
FLOW CHART NO.5 A cassette tape is taken in, but ejected at once.
FLOW CHART NO.2 Key-in input is not received.
47
Does the key switch make good contact, when the cassette tape is inserted? YES Is there the function control voltage inputted at the pins(87) and (88) of IC701? YES
NO
Check switch contact.
Does the start sensor pulse at pin(79) of IC701 change from "L" to "H" level when the cassette tape is loaded? YES Does the end sensor pulse at pin(85) of IC701 change from "L" to "H" level when the cassette tape is loaded? YES Does the master cam mode shifteroperate normally when the cassette tape is loaded? YES Replace IC701.
NO
Check line start sensor and all the way up thru to pin(79) of IC701.
NO
Check line end sensor and all the way up thru to pin(85) of IC701.
NO
Check cam switch (A), (B) and all the way up thru to pins(7), (6) of IC701.
NO
See FLOW CHART NO.8.
FLOW CHART NO.6 The cassette tape fails to eject.
Check or place the peripheral circuit of IC701.
FLOW CHART NO.3 No operation is possible from the infrared remote control.
NO
NO
NO
Check AT 5V lines.
Replace the remote control receiver or replace the remote control transmitter if necessary. Check line between at remote control receiver thru to pin(5) of IC701.
NO
NO NO
NO NO
NO
Check reel disk and reel drive unit.
Check take-up reel sensor and all the way up thru to pin(2) of IC701. Check pin(90) of IC701.
Check IC7002. Check between IC7002 and all the way up thru to the loading motor. Replace loading motor.
DV-NC55S/H DV-NC60H
Operation is possible from the VCR, but no operation is possible from the infrared remote control. YES Is the supply voltage of 5V feed to pin(3) terminal of remote control receiver? YES Is "L" pulse sent out pin(1) terminal of receiver when the infrared remote control is activated? YES Is inputted "L" pulse to pin(5) of IC701? YES Replace IC701.
Does the capstan motor start when the EJECT button is pressed? YES Does the take-up reel disk turn when the capstan motor is running? YES Are pulses applied at pin(2) of IC701 when the take-up reel disk is turning? YES Is a "H"(about 4.7V) level applied at pin(12) of IC7002 when a reel pules has been inputted? YES Is the voltage about 10V sent out of pin(15) of IC7002? YES Is the specified voltage applied at the loading motor terminal? YES Dose the loading motor run? YES Replace cassette cam, gear, etc.
FLOW CHART NO.9
No power is turned on. Does power control(H) signal at pin(94) of IC701 change from "L" to "H" level? YES Does the base voltage of RJ9904 change from about 12.6V to 11.8V? YES Is voltage of 12V sent out from the emitter of RJ9904 transistor? YES Does the base voltage of Q9903 change from about 5.5V to 6.2V?
The drum motor fails to run.
NO
NO
NO
NO
YES NO Is voltage of 5V sent out from the emitter of Q9903 transistor? YES Check peripheral circuit for poor soldering.
Check line between emitter of RJ9904 and base of Q9903.
NO Is the voltage more than about 2.6V DC given out of pin(58) of IC701. YES NO Is the supply voltage of 5V feed to pin(3) of IC7002? YES NO Is the voltage more than about 2.6V applied at pin(2) of IC7002? YES NO Is the supply voltage of 12V feed to pin(21) of IC7002? YES Check or replace drum motor.
Check peripheral circuit of Q9903 and AT 5V line.
FLOW CHART NO.10
Check IC701.
Check line between RJ9904, Q9905 and IC701.
Check peripheral circuit of RJ9904 and AT 12V line.
Is drum PG signal given out of pin(7) of IC7002? YES
The capstan motor fails to run. NO
NO
48
NO NO
NO
Check IC1701.
Check PC 5V line. Check between pin(58) of IC701 and all the way up to pin(2) of IC7002. Check PC 12V line.
The drum motor runs only for a few seconds. NO
FLOW CHART NO.8
Is the voltage more than about 2.6V DC given out of pin(59) of IC701. YES Is the supply voltage of 5V feed to pin(8) of AC connector? YES Is the voltage more than 2.6V DC sent in pin(4) of AC connector? YES Is approx. 3.5V applied to the pin(3) of the AC connector? YES Is 23V applied to the pin(5) of the AC connector normally? YES Replace capstan motor.
DV-NC55S/H DV-NC60H
FLOW CHART NO.7
Check IC701.
Check PC 5V line.
Is drum PG signal given out of pin(66) of IC701? YES Is V-H.SW.P pulse given out of pin(23) of IC701? YES Replace IC701.
Check between the pin(4) of AC connector and all the way up thru to pin(59) of IC701.
FLOW CHART NO.11
Check the pin(60) of IC701.
Is the drum motor rotating? YES
NO
NO
Check pins(4), (5), (6) of IC7002 and periperal circuits. YES Check or replace drum motor. Check line between pin(7) of IC7002 and all the way up thru to pin(66) of IC701. Check IC701.
No head switching pulse.
Check AT 23V line.
Is the drum PG signal and drum FG signal present on pins(66) and (65) of IC701, respectively? YES
NO
NO
See FLOW CHART NO.9, 10 Replace IC701.
D-FG
D-PG About 5Vp-p
Are the drum PG and drum FG signals present on pins(7) and (8) of IC7002? YES Check periperal circuit of IC7002.
NO
About 5Vp-p
Check line between pins(7), (8) of IC7002 and all the way up thru to pins(65), (66) of IC701.
FLOW CHART NO.14
FLOW CHART NO.12 Drum servo does not function.
Picture E-E does not appear.
Is there 14.3MHz oscillation at pins(37) and (38) of IC701? YES In PB mode Is there drum FG signal at pin(65) of IC701 present? YES NO
NO
Check peripheral circuit of X701.
YES
Is picture signal input into pins(30), (28) and (31) of IC201? YES
In REC mode Is the V-SYNC signal(reference) at pin(50) of IC701? NO Check peripheral circuit of C746-747 and R745.
NO NO
NO
1 External input mode • Check the line between the front video input terminal and pin(28) of IC201. 2 U/V tuner mode Check the line between the pin(25) of U/V tuner and pin(31) of IC201.
Is picture signal output to the pin(52) of IC201? NO YES Is 5V applied to the pin(12) of IC201? Is picture signal input into the pin(49) of IC701? YES YES NO NO
Check drum FG signal line. Is the head switching pulse at pin(23) of IC701 present? YES Is the drum APC output at pin(34) of IC701 and drum AFC output at pin(32) of IC701 present? YES Is the drum control voltage applied to pin(2) of IC7002? YES Does the IC7002 operate normally? YES Replace drum motor.
NO
See FLOW CHART NO.11
Check the YC 5V line.
Check the line between pin(52) of IC201 and pin(49) of IC701.
Replace IC701.
Is serial data clock signal applied to the pins(63) and (62) of IC201?
Is picture signal output to the pin(47) of IC701 ? NO YES Is 5V applied to the pin(51) of IC701?
Is pin(58) of IC701 in high impedance?
NO Check the line between pins(63) and (62) of IC201 and pins(56) and (57) of IC701.
NO Check the AT 5V line.
Is picture signal output to the emitter of video output buffer (Q708)?
FLOW CHART NO.13 Capstan servo does not function.
NO
Check Q708 periphery.
YES
49
1Only PB mode inoperative
RF output: Check Q708 periphery and tuner pin(6) periphery.
Are REC and/or PB mode inoperative? YES Check peripheral circuit of X701.
NO
NO
Check the line between the Q708 emitter and the pin(3) of IC2004.
YES
YES
NO Check AC-MC connector and capstan FG signal line.
Line output: Is there V-SYNC signal input at pin(3) of IC2004.
Is there 14.3MHz oscillation at pins(37) and (38) of IC701? Does the capstan FG signal appear at pin(67) of IC701?
Is there V-SYNC signal output at pin(7) of IC2004. YES
NO
Is 5V applied to the pin(6) of IC2004. NO YES
YES Check capstan motor unit and/or replace. Does PB CTL signal appear at pin(76) of IC701 (TP201)?
YES
Does AA-MH harness normally?
NO
YES YES Does A/C head operate normally? NO Replace A/C head.
YES Is there capstan AFC and APC at pins(31) and (33) of IC701?
YES Does pin(59) of IC701 operate normally?
Check the PC 5V line. Are the pin(1) of IC2004 on "L" level? YES NO Replace IC2004.
Check the DVD-H line.
YES
NO Replace IC701.
NO
Check the VIDEO OUT terminal (J1202) and the line between the pin(7) of IC2004 and the VIDEO OUT terminal (J1202).
Is there capstan AFC and APC at pins(31) and (33) of IC701?
Check "1" NO Check "2"
Replace AA-MH harness.
2Only REC mode inoperative
Readjust the A/C head height. NO Check peripheral circuit of C746-747 and R745.
Is the V-SYNC signal(reference) at pin(50) of IC701? YES
Replace IC701.
NO
DV-NC55S/H DV-NC60H
Is there REC CTL signal output at pins(75) and (74) of IC701? YES NO
Picture (luminance) record is impossible (E-E mode is possible). Is luminance signal (approx. 0.5 Vp-p) input to the pin(19) of IC201?
NO
Check between the pins(18) and (19) of IC201.
Is voltage 5V applied to the chroma NO power terminal pin(61) of IC201?
Check the periphery of pin(61) of IC201 and PC 5V line.
NO
Check between the pins(21) and (42) of IC201. (Check C208.)
YES Is chroma signal (approx. 156 mVp-p NO /Burst) input into the pin(46) of IC201?
Check between the pins(60) and (46) of IC201. (Check C512.)
NO
Check between the pins(39) and (26) of IC201. (Check C212.) YES
YES Is luminance signal (approx. 0.3 Vp-p) input to the pin(42) of IC201? YES Is luminance signal (approx. 0.5 Vp-p) input to the pin(26) of IC201? YES
Although picture record is possible, color does not appear (E-E mode is possible).
Is luminance signal (approx. 0.5 Vp-p) input to the pin(39) of IC201? NO
YES Check whether the pins(75) and (73) of IC201 oscillate (4.43 MHz)?
YES
Is chroma signal (approx. 197 mVp-p NO /Burst) input into the pin(58) of IC201?
Check between the pins(58) and (35) of IC201. YES
YES Is voltage 5V applied to the CCD section power terminal pin(36) of IC201?
NO
YES
50
Is CCD control voltage approx. 0V applied normally to the pin(37) from the pin(57) of IC201? Is clock signal (approx. 8.86 MHz/ 0.5 Vp-p) for CCD applied normally to the pin(44) from the pin(69) of IC201?
Is chroma signal (approx. 197 mVp-p /Burst) output to the pin(35) of IC201?
SP mode: Is there chroma ingredient included signal (approx. 20 mVp-p) output at pins (88), (89) ((SP1)) and pins (86), (87) ((SP2)) of IC201? LP mode: Is there chroma ingredient included signal (approx. 20 mVp-p) output at pins (93), (94) ((EP1)) and pins (92), (91) ((EP2)) of IC201? YES
Is luminance signal (approx. 0.5 Vp-p) input to the pin(23) of IC201? YES Is the luminance signal (approx. 0.5 Vp-p) input and output to the pins(13) and (14) of IC201, respectively?
NO
Check between the pins(24) and (23) of IC201. (Check C210.)
Is PRE/REC Vcc 5V applied to the pin(90) of IC201? NO Replace IC201.
NO
Check the pins(13) and (14) of IC201 peripheral circuit. (R201, R202, C203, C225)
YES SP mode: Is record FM signal (approx. 20 mp-p) output to the pins(88) and (89) (SP1) and pins(86) and (87) (SP2) of IC201? LP mode: Is record FM signal (approx. 20 mp-p) output to the pins(93) and (94) (LP1) and pins(92) and (91) (LP2) of IC201? YES Check or replace the cylinder.
DV-NC55S/H DV-NC60H
FLOW CHART NO.15
FLOW CHART NO.16 Playback picture does not appear (E-E mode is possible). Is FM signal (approx. 200mVp-p) NO input to the pin(78) of IC201? YES
Although picture is played back, color does not appear (E-E mode is possible).
Check between the pins(79) and (78) of IC201. YES Is luminance signal (approx. 200mVp-p outputted at the pin(78) of IC201? YES Is V-H.SW.P. applied to the pin (81) of IC201? YES Check V-H.SW.P. line.
Is the luminance signal input and output to the pins(13), (14) of IC201?
NO
Check the periphery of pins(13) and (14) of IC201.
YES
51
Is luminance signal (approx. 0.5 Vp-p) input to the pin(19) of IC201? YES
NO
Check between the pin(18) and pin(19) of IC201.
Is luminance signal (approx. 0.3 Vp-p) input to the pin(42) of IC201? YES
NO
Check between the pin(21) and pin(42) of IC201. (Check C208.)
Is luminance signal (approx. 0.5 Vp-p) input to the pin(26) of IC201?
NO
Check between the pin(39) and pin(26) of IC201. (Check C212.)
YES
Is voltage 5V applied to the chroma NO power terminal pin(61) of IC201?
Check the periphery of pin(61) of IC201 and PC 5V line.
YES Is chroma signal (approx. 156 mVp-p/Burst) input into the pin (46) of IC201?
NO
Check between the pin(60) and pin(46) of IC201. (Check C512.) YES
YES
Check whether the pin(75) and pin (73) of IC201 oscillate (4.43 MHz)? NO
Is chroma signal (approx. 197 mVp-p/Burst) input into the pin (58) of IC201?
Check between the pin(58) and pin(35) of IC201.
YES Is chroma signal (approx. 300 mVp-p/Burst) input into the pin (54) of IC201?
YES YES
NO Check between the pin(55) and pin(54) of IC201.
Is chroma signal (approx. 197 mVp-p/Burst) output to the pin (35) of IC201? NO
Replace IC201.
YES Is luminance signal (approx. 0.5 Vp-p) input to the pin(39) of IC201? NO Is voltage 5V applied to the CCD section power terminal pin(36) of IC201? YES Is control voltage approx. 5V applied normally to the pin(37) from the pin(57) of IC201? Is CCD clock signal (approx. 8.86 MHz/0.5 Vp-p) applied to the pin(44) from the pin(69) of IC201?
Is luminance signal (approx. 0.5 Vp-p) input to the pin(23) of IC201? YES
NO
Check between the pins(24) and (23) of IC201. (Check C210.)
Is luminance signal (approx. 0.5 Vp-p) input at pin(52) of IC201? NO Replace IC201.
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
FLOW CHART NO.17 Hi-Fi SOUND MODE TROUBLESHOOTING(1) (For Hi-Fi model) No Hi-Fi E-E sound heard
Is there audio signal inputted at each input terminal as shown in table? Tuner input terminal. IC2501 IC2501 NO pin(16) pin(15) Decoder signal input IC6301 IC6301 NO terminal. pin(61) pin(52) YES
Check line ranging from pins (31),(30) of IC1701 (NICAM/GR), to the each input terminal of IC2501. Check line ranging from pins (39),(40) of IC2501 (decoder circuit) or audio input terminal to the each input terminal of IC6301. Check PC5V and Hi-Fi 9V line. NO Is the supply voltage of PC 5V fed to pins(14), (30), (36) and 9V fed to pin (60) of IC6301?
Is there audio signal inputted at each input terminal of IC201 as shown in table? U/V tuner audio input pin(8) NO terminal. Aux input terminal. pin(9) NO
Check line ranging from A-out pin (21), of TU1401. Check line ranging from pin (53) of IC6301.
YES Replace IC201. YES Is there audio signal outputted at pins (11), of IC201? YES
NO
Is there "L" level at pin(99) of IC201? NO Check line between pin (8) of IC6301 and pin (21) of IC701.
YES Is there audio signal outputted at pins (4), (46) of IC6301? YES
NO
Are there the serial data and clock at pins (31) and (32) of IC6301? NO
52
Check line between pins (31), (32) of IC6301 and pins (26), (27) of IC701? Is there audio signal outputted at pins (5), (45) of IC6301? YES
NO
Check line between pins (4, 46) and (5,45) of IC6301. (C6302, C6320)
Is there audio signal outputted at pin (54) of IC6301?
NO
Check line between pin (11) of IC201 and pin (54) of IC6301.
YES Line output terminal: Is there audio signal outputted at pins (58) and (56) of IC6301? NO
YES YES
Is there "L" level at pin (8) of IC6301? NO Check line between pin(8) of IC6301 and pin (21) of IC701. Replace IC6301.
Line output terminal Check line ranging from pins (58) and (56) of IC6301 to pins (2) and (1) of IC2501.
FLOW CHART NO.20 LINEAR SOUND MODE TROUBLESHOOTING(1) (For MONO model)
FLOW CHART NO.18 Hi-Fi SOUND MODE TROUBLESHOOTING(2) (For Hi-Fi model)
No E-E sound
No Hi-Fi sound recording (E-E mode is posible). NO
Is there audio signal inputted at input terminal as shown in table? Decoder or aux signal input terminal. NO Pin (9) of IC201 NO Front A/V signal input terminal. Pin (11) of IC2501 (DECODER) or Front A/V signal input terminal pin (7) of IC201.
Replace IC6301.
Check peripheral circuit of IC6301 as shown in table. L-ch pins (41),(40),(39),(38),(37) R-ch pins (10),(11),(12),(15),(16) YES Is there a REC FM signal outputted at the IC6301 pins(26) to (22) (CH-1)/pins (26) to (25) (CH-2).
Check PC 5V lines. NO Is the supply voltage of 5V fed to pin (20) of IC6301? YES Is there "L" level at pin (33) of IC6301? NO
NO
YES Check AH-MZ harness. YES
Check the record current setting resistor R352 and pin (27) of IC6301.
YES
NO
Is there audio signal outputted at pin (11) of IC201? (DECODER)
Check PC 5V lines. NO NO
YES
Check AUDIO MUTE (H) line between pin (99) of IC201 and pin (21) of IC701.
FLOW CHART NO.19 Hi-Fi SOUND MODE TROUBLESHOOTING(3) (For Hi-Fi model) No Hi-Fi sound playback(E-E mode is possible).
Check PC 5V lines. NO
NO
Is the supply voltage of 5V fed to pin (20) of IC6301?
Is there playback envelope signal outputted at pins (19) to(18) of IC6301?
YES
Does the trap circuit operate normally? YES
NO
R-ch pins (10),(11),(12),(15),(16)
53
YES Replace IC6301.
Check the trap circuit. (Q601, Q602).
YES
YES
L-ch pins (41),(40),(39),(38),(37)
Is the supply voltage of 5V fed to pin (96) of IC201? YES Is there "L" level at pin (99) of IC201? YES
Check or replace the cylinder.
Check peripheral circuit of IC6301 as shown in table.
Check line ranging from pin (39) of IC2501 (DECODER) or from SCART input terminal. Check line ranging from Front A/V input terminal (J2101).
To Output Terminal
YES
Is there A-H.SW.P. signal at pin (35) of IC6301? NO Check the A-H.SW.P. line between pin (35) of IC6301 and pin (28) of IC701.
NO Line output terminal : Is there audio signal inputted at pins (2) of IC2501?
Check line between Q601, Q602 of IC201 and Audio Output terminal.
YES
Is there audio signal outputted at pins (42), and (30) of IC2501? YES
For Single SCART MONO NO
Check peripheral circuit of IC2501.
Check line between IC2501 peripheral and output terminal peripheral.
DV-NC55S/H DV-NC60H
FLOW CHART NO.23 NICAM/IGR TROUBLESHOOTING (For Hi-Fi model) No NICAM/IGR
No linear sound recording (E-E mode is possible) Is "L" level applied at pin (99) of IC201? YES Is there signal at pin (4) of IC201? YES Is the supply voltage of 12V fed to pin (2) of T651? YES Is there signal (Bias) at pin (5) of T651? YES Is there signal (Bias + Audio sig) at pin (6) of T651? YES Check the MH-AA harness and A/C head.
NO
NO NO NO
NO
Check the AUDIO MUTE (H) line between pin (99) of IC201 and pin (21) of IC701. Replace IC201. Check M 12V line. Check the Bias oscillation circuit (T651, Q651, Q652) and A-ERASE CTL line. Check peripheral circuits of T651.
FLOW CHART NO.22 LINEAR SOUND MODE TROUBLESHOOTING(3) (For Hi-Fi and MONO model) No linear sound playback (E-E mode is possible) Is there signal at pin (100) of IC201? YES
YES Replace IC201. YES Clean A/C head. YES NO Is the azimuth height of A/C head properly adjusted?
Are there signal at pin (1) of IC681? PAL EP ONLY YES
54
Re-adjust azimuth.
YES Is there signal at pin (11) of IC201. YES Is there audio signal inputted at pin(54) of IC6301?
Are there MH-AA harness and the PB AMP peripheral parts normal?
NO
NO
NO
YES Replace A/C head. YES Check the AUDIO MUTE (H) line between pin (99) of IC201 and pin (21) of IC701. Replace IC201.
Check peripheral circuit of TU1401. Check between SIF OUT of TU1401 and pin(2) of IC1701.
(2) of IC1701? YES
Check PC5V line. NO Is there a NICAM/IGR audio signal NO at pins(31), (30) of IC1701? YES
Is 5V supplied at pins (11), (19), (1) of IC1701? YES YES
Is there a NICAM/IGR audio signal at pin (15), (16) of IC2501?
Is MPX 8V supplied at pin (33) of IC1701? NO
YES
NO
Is there "L" level at pin (99) of IC201.
Is there a base band signal at SIF NO OUT of TU1401? YES Is there a base band signal at pin NO
Check line between pin (39), (40) of IC2501 and pins(52), (61) of IC6301. NO
Check the REG. circuit of D9912. YES
See Flow Chart No. 17 Hi-Fi SOUND MODE TROUBLESHOOTING (1) For Hi-Fi model
Check serial data and clock at pin NO (12) and (13) of IC1701.
Check PC Motor 12V line.
YES NO
Check peripheral circuit of X1701.
Is there oscillated 18.432MHz at pins(5), (6) of IC1701? YES Check peripheral circuit of IC1701. YES Replace IC1701. Check between IIC Data pins(26), (27) of IC701 and pins(12),(13) of IC1701.
Check line between pin (11) of IC201 and pin (54) of IC6301. Hi-Fi model ONLY
DV-NC55S/H DV-NC60H
FLOW CHART NO.21 LINEAR SOUND MODE TROUBLESHOOTING(2) (For Hi-Fi and MONO model)
FLOW CHART NO.24 DECODER TROUBLESHOOTING (For 2 SCART Hi-Fi and MONO model) Not output from 21pin connector in video and audio signal. NO Is voltage 5V applied to the video section power terminal at pins(24), (29) of IC2501? YES Is voltage 12V applied to the audio section power terminal at pins(14) of IC2501? YES Is there SDA and SCL signal applied to pins(21) and (22) of IC2501?
NO
NO
Check STBY 5V line.
Check STBY 12V line.
Check line between pins(21), (22) of IC2501 and pins(17), (18) of IC701.
YES Check signal line from video and audio function logic table as shown below.
55
SIG. SIG. MODE DECODER CIRCUIT INPUT SIGNAL OUTPUT SIGNAL FLOW INPUT (switch) OUTPUT FLOW SELECT E1(L1) video output Pin47 of IC701(Y/C video output) > > (A) pin25 pin7 21PIN CONNECTOR E2(L2) video input > (B) pin28 Front video input > (C) pin13 E1(L1) audio output(L/R-ch) Pin11 of IC201 (Audio output) > > (A) pin42 pin2 21PIN CONNECTOR E2(L2) audio input(L/R-ch) > (B) pin33 Front audio input > (C) pin11 E2(L2) video output Tuner video output > > (A) pin26 pin18 21PIN CONNECTOR E1(L1) video input > (B) pin23 Pin47 of IC701(Y/C video output) > (C) pin7 E2(L2) audio output(L/R-ch) Tuner audio output > > (A) pin30 pin16 21PIN CONNECTOR E1(L1) audio input(L/R-ch) > (B) pin36 Pin11 of IC201(Audio output) > (C) pin2 Pin31 of IC201 E2(L2) video input > > (A) pin5 pin28 Y/C video input E1(L1) video input > (B) pin23 (Aux. input) Tuner video output > (C) pin18 Front video input > (D) pin13 Pin9 of IC201 E2(L2) audio input (L/R-ch) > > (A) pin39 pin33 Audio input E1(L1) audio input (L/R-ch) > (B) pin36 Tuner audio output > (C) pin16 Front audio input > (D) pin11
SIG. MODE SIG. DECODER CIRCUIT INPUT SIGNAL OUTPUT SIGNAL FLOW INPUT (switch) OUTPUT FLOW SELECT E1(L1) video output Pin47 of IC701(Y/C video output) > (A) > pin25 pin7 21PIN CONNECTOR E2(L2) video input > (B) pin28 Front video input > (C) pin13 E1(L1) audio output(L-ch) Pin58 of IC6301 (Audio output L-ch) > (A) > pin42 pin2 21PIN CONNECTOR E2(L2) audio input(L/R-ch) > (B) pin33 Front audio L-ch input > (C) pin11 E1(L1) audio output(R-ch) Pin56 of IC6301(Audio output R-ch) > (A) > pin43 pin1 21PIN CONNECTOR E2(L2) audio input(R-ch) > (B) pin34 Front audio R-ch input > (C) pin10 E2(L2) video output(L-ch) Tuner video output (A) > > pin26 pin18 21PIN CONNECTOR E1(L1) video input (B) > pin23 Pin47 of IC701(Y/C video output) (C) > pin7 E2(L2) audio output(L-ch) MPX output(L-ch) (A) > > pin30 pin16 21PIN CONNECTOR E1(L1) audio input(L-ch) (B) > pin36 Pin58 of IC6301(Audio output L-ch) (C) > pin2 E2(L2) audio output(R-ch) MPX output(R-ch) (A) > > pin31 pin15 21PIN CONNECTOR E1(L1) audio input(R-ch) (B) > pin37 Pin56 of IC6301(Audio output R-ch) (C) > pin1 Pin31 of IC201 E2(L2) video input (A) > > pin5 pin28 Y/C video input E1(L1) video input (B) > pin23 (Aux. input) Tuner video output (C) > pin18 Front video input (D) > pin13 Pin61 of IC6301 E2(L2) audio input (L-ch) (A) > > pin39 pin33 (Aux. input) E1(L1) audio input (L-ch) (B) > pin36 MPX output(L-ch) (C) > pin16 Front audio L-ch input (D) > pin11 Pin52 of IC6301 E2(L2) audio input (R-ch) (A) > > pin40 pin34 (Audio input (R-ch) E1(L1) audio input (R-ch) (B) > pin37 MPX output (R-ch) (C) > pin15 Front audio R-ch input (D) > pin10
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
(POWER) FLOW CHART NO.1
FLOW CHART NO.5
No power Is the fuse good? YES
NO
Is the normal state restored when once unplugged NO power cord is plugged again after several seconds? YES NO Are AT 5V voltage line normal? YES NO Are STBY 44V, AT 23V, PC 12V, STBY –24V, STBY 5V and filament voltage lines normal? YES Is "H" level applied at pin(1) of IC701?
NO
The fuse blows out even when it is replaced with new one. See FLOW CHART NO.2 .
Check for leak or short-circuiting of primary circuit part.(L901, D910-3, T901, Q901-902, etc.)
Check each rectifier circuits and short-circuit of secondary circuit. Check the power failure circuit. (Q704 and the peripheral circuit)
FLOW CHART NO.2 Fuse blown out. Case (1) Check for leak or short-circuiting of primary circuit part. (L901, T901, Q901-902, etc.)
Case (2) Check for short-circuiting of rectifying diode and circuit in each rectifying circuit of secondary circuit. (D9601-6)
FLOW CHART NO.3
56
When the output voltage varies. NO Is the photocoupler circuit on the secondary side operating normally? YES Is the control of photocoupler circuit on the primary NO side operating normally? YES
Check the circuit and replace parts. (IC901, IC902, IC9601, etc.) Check the circuit and replace parts. (IC901, IC902, IC9601, Q902, etc.)
Replace IC701, IC702.
FLOW CHART NO.4 When buzz is heard from the vicinity of power circuit. Check for short-circuiting of circuit and rectifying diode of each rectifying circuit of secondary circuit and check for failure of shunt regulator circuit. (D9601-6, IC9601, C9613, C9618)
The DVD power cannot be turned on. Does the change from STANDBY LED indicate YES turn-off? YES NO Is the supply voltage of 5V fed to pin(9) of IC8201? YES Is the supply voltage about 5V fed to pin(11) of IC8201? YES Is there 4.0MHz oscillation at pins(6) and (8) of IC8201? YES Does the "L" signal inputted at pin(13) of IC8201, when the POWER button activated on the DVD? YES Does the remote control "L" signal inputted at pin(10) of IC8201, when the POWER button activated on the remote control unit? YES Replace IC8201.
NO
NO
NO
NO
Check the AT 5V line.
Check the IC8202.
Check the FL8201 and IC8201.
Check the S5001 and POWER KEY line.
Check the line between the remote control receiver and the pin(10) of IC8201.
The STANDBY LED indicate it flashing after 0.5sec. Yes (below, confirmed operating at LED turn-off of 0.5sec interval.) Replace IC8201. Are the "P–CON(L)" pulse outputted from the NO pin(32) of IC8201? YES NO Check each component and if poor the replace. Does the P–CON switch circuit is operate normally? (Q9053-5, Q9058, IC9053-54) YES NO Are the "H" pulse inputted into the pin(33) of Check or replace D9091-95. IC8201? YES Replace IC8201.
FLOW CHART NO.6
FLOW CHART NO.9
PC 9V is not output.
PC -22V is not output.
Is 12V voltage supplied at pin(1) of IC9052? YES Is voltage of 9V sent out from the pin(2) of IC9052? NO Check the IC9052 periphery circuit.
NO
YES
NO Does the P-CON switch circuit is operate ally? (Q9056-7, Q9053, etc.) YES NO Are the "H" pulse inputted into the pin(9) of IC8201? YES Replace IC8201.
Check the secondary circuit, AT 12V and PC 12V switch(Q9053) circuit. Check for load circuit short-circuiting or leak.
Check each component and if poor the replace.
Check or replace D9091-5.
FLOW CHART NO.7
Check the AT -22V line. Check for load circuit short-circuiting or leak.
Check each component and if poor the replace.
Check or replace D9091-5.
FLOW CHART NO.10
PC 8V is not output.(PC 9V is possible)
PC 3.3V(1), (2) is not output.
NO Is 12V voltage supplied at pin(1) of IC9052? YES YES Is voltage of 8V sent out from the pin(2) of IC9052? NO Check the IC9052 periphery circuit. YES Replace IC9052.
Check the PC 12V line. Check for load circuit short-circuiting or leak.
57
FLOW CHART NO.8 PC 5V is not output. Is 5V voltage supplied at emitter of Q9054? YES Is voltage of 5V sent out from the collector of Q9054? NO Check the Q9054 periphery circuit. YES Does the P-CON switch circuit is operate normally? (Q9056-7, etc.) YES Are the "H" pulse inputted into the pin(9) of IC8201? YES Replace IC8201.
NO Is -22V voltage supplied at emitter of Q8202? YES YES Is voltage of -22V sent out from the collector of Q8202? NO Check the Q8202 periphery circuit. YES NO Does the P-CON switch circuit is operate normally? (Q8201, etc.) YES NO Are the "H" pulse inputted into the pin(32) of IC8201? YES Replace IC8201.
NO YES
Check the AT 5V line. Check for load circuit short-circuiting or leak.
NO Is 5V voltage supplied at pin(1) of IC9053? YES YES Is voltage of 3.3V sent out from the pin(2) of IC9053? NO Check the IC9053 periphery circuit. YES NO Does the P-CON switch circuit is operate normally? (Q9056-7, etc.) YES NO Are the "H" pulse inputted into the pin(9) of IC8201? YES Replace IC8201.
Check the secondary circuit, AT 5V line. Check for load circuit short-circuiting or leak.
Check each component and if poor the replace.
Check or replace D9091-5.
FLOW CHART NO.11 PC 1.8V is not output.(PC 3.3V(1), (2) is possible)
NO
NO
NO
Check each component and if poor the replace.
Is 5V voltage supplied at pin(1) of IC9054? YES Is voltage of 2.5V sent out from the pin(2) of IC9054?
YES
Check or replace D9091-5.
NO Check the IC9054 periphery circuit.
YES
Check the secondary circuit, AT 5V line. Check for load circuit short-circuiting or leak.
Replace IC9054.
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
12. IC FUNCTION LIST 12-1. IC301 TA1323F Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
RF PROCESSOR
Terminal name GND P2TP P2TN LDO2 MDI2 VrD Vrfil Vdd DPAC DPBD DPD1 DPD2 SCB SCL SCD VRCK
I/O – I I O I O – I – – – – I I I I
Operation function GND terminal. TE+input (CD) TE–input (CD) Drive ouput 2 Monitor input 2 Digital VREF Filter capacity for reference Power terminal DPD AC combination capacity 1 DPD AC combination capacity 2 DPD integral capacity 1 DPD integral capacity 2 Control line (Bit clock) Control line (Latch signal) Control line (Sirial Data) Reference clock input
Terminal DC Voltage(TYP.) Remarks – VrA VrA – – – Vdd/2 output (1.65V) – – 3.3V is connected. – – – – 2.2[V] 2.2[V] 2.2[V] 2.3[V] When frequency is increased, the filters excepting the servo LPF are shifted to high frequency side. –
17
VCKF
–
18 19 20 21 22 23 24 25 26 27 28 29
VccP LVL TEO FEO DFTN VccS NC RPZ RPO RPB RPP RFOn
– O O O I – – O O – – O
30
RFOp
O
31 32 33
VccR RFS TEB
– I I
Capacity for VRCK time constant adjustment Power terminal Servo addition output TE output FE output DPD difect Power terminal (servo) – RF ripple output 2 RF ripple output 1 RF ripple bottom RF ripple peak Equivalent RF output (Differential output) Equivalent RF output (Differential output) Power terminal (RF) RF slice level adjustment TE balance
34
FEB
I
FE balance
VrD
35
DPDB
I
Pit depth adjustment
VrD
36 37 38 39 40 41 42 43
Vcc2 NC NC GND2 TCC1 RFDC VrA EQB
– – – – I – O I
Power terminal – – GND terminal. Time constant adjustment DC feedback capacity Analog VREF Boost adjustment
– VrD/2 VrD VrD – – – VrD VrD/2 – – 1.65[V] 1.65[V] – – VrD
– – – – – – 2.1[V] VrD
58
Low DPD output: Mute Used in the open state.
DC voltage varies by RFS. DC voltage varies by RFS.
When TEB is raised, the gain on the TP side and the delay amount on the A+C side are increased. Adjusting range: GND - Vdd When FEB is raised, the gain on the A+C (FP) side is increased. Adjusting range: GND - Vdd When DPDB is raised, the delay amount on the A•B side is increased. Adjusting range: GND - Vdd Used in the open state. Used in the open state.
When EQB is raised, the boost increases. Adjusting range: GND - Vdd
DV-NC55S/H DV-NC60H
TEB
P1TP
• Block Diagram
FEB
A input (CD) B input (CD) C input (CD) D input (CD) GND terminal (Servo) FE+input (CD) FE–input (CD)
DPDB
I I I I – I I
Vcc2
P2AI P2BI P2CI P2DI GNDS P2FP P2FN
NC
58 59 60 61 62 63 64
NC
D input (DVD) C input (DVD) B input (DVD) A input (DVD) GND terminal (RF) APC polarity 2
GND2
I I I I – I
TCC1
P1DI P1CI P1BI P1AI GNDR LDP2
VrA
52 53 54 55 56 57
EQF
Monitor input 1 Drive output 1 TE–input (DVD) TE+input (DVD) FE–input (DVD) FE+input (DVD) APC polarity 1
MDI1
I O I I I I I
LDO1
MDI1 LDO1 P1TN P1TP P1FN P1FP LDP1
P1TN
45 46 47 48 49 50 51
Terminal DC Voltage(TYP.) Remarks VrD When EQF is raised, shift to the high frequency side occurs. Adjusting range: GND - Vdd – – VrA VrA VrA VrA – Positive polarity when this terminal is connected to Vcc. VrA VrA VrA VrA – – Positive polarity when this terminal is connected to Vcc. VrA VrA VrA VrA – VrA VrA
RFDC
I/O Operation function I Frequency adjustment
EQB
Pin No. Terminal name 44 EQF
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
LDP1
51
P1DI
52
P1CI
53
P1BI
54
sel-RF
sel-PD
F-gain Adjust
GNDR 56 LDP2
P2BI
59
P2DI
28 RPP 27 RPB
RF Ripple creation
26 RPO
FEB sel-FE
57 58
F-gain Adjust
sel-PD
DPDB
sel-TE
sel-DPD
60 sel-PD
T-gain Adjust
GNDS 62
23 VccS mode-TE
5
6
7
P2TN
LDO2
MDI2
VrD
Vrfil
8
9 10 11 12 13 14 15 16
59
DPD1
4
17 VCKF
BUS
DPBD
3
18 VccP
DPAC
2
19 LVL
Vdd
1
P2TP
64
20 TEO
Time constant adjustment
TCC1
Vref
GND
P2FN
21 FEO Level detect
tcc1 (BUS)
63
22 DFTN
TE-gain Adjust
TEB
sel-LVL
APC2
24 NC
TEB
VrA
P2FP
25 RPZ
FE-gain Adjust
DPD-TE creation
3Beam-TE creation
61
29 RFOn
EQ
FE creation
P2AI
P2CI
DC FB
R-gain Adjust
mode-IC
55
30 RFOp
Output Amp
DPD2
P1AI
31 VccR
VRCK
50
SCD
P1FP
32 RFS
APC1
SCL
49
SCB
P1FN
DV-NC55S/H DV-NC60H
12-2. IC501 IX1689GE Pin No.
Symbol
45
DQ15/A-1
25-18, 8-4
A0-A12
3-1, 48, 16, 17 29, 31, 33, 35, 38, 40, 42, 44 30, 32, 34, 36, 39, 41, 43, 45
DQ8-DQ14
26
CE#
12
RP#
28
OE#
11
WR#
14
WP#
15
RY/BY#
47
BYTE#
13 37 27, 46 9, 10
Vpp Vcc GND NC
A13-A18 DQ0-DQ7
FLASH MEMORY Type
Name and function Byte selection address: When the device is in the x8 mode, the low or high order byte is Input selected. It is not used in the x16 mode. (If BYTE# is high, DQ15/A-1 input circuit does not operate.) Word selection address: Selection of one word of 16k byte block. These addresses are Input latched during data wiring operation. Block selection address: Selection of 1/32 erase block. These addresses are latched Input during data writing, erasing and lock block operation. Low order byte data input/output: Command user interface writing cycle data and command Input/Output input. Various data read memory identifier and status data output Chip nonselection or output disable: Float state High order byte data input/output: The function is the same as that of low order byte Input/Output data input/output. Operative only in x16 mode. x8 mode: Float state DQ15/A-1 is address. Chip enable: Device control logic, input buffer, decoder and sense amp. are activated. Input Chip becomes active only when CE# is “Low”. Reset/Power down: If RP# is set to “Low”, the control circuit is initialized when power is turned on. Hence, the RP#pin is set to “Low”. When power is turned on or off or in case of fluctuation it is kept at “Low” so as to protect data from noise. When RP# is in Input “Low” state, the device is in deep power down state. 480 ns is required to recover from the deep power down state. If the RP# pin becomes “Low”, the whole chip operation is interrupted and reset. After recovery the device is set to array read state. Output enable: When OE# is set to “Low”, data is output from the DQ pin. When OE# is Input set to “High”, the DQ pin is set to float state. Write enable: Command user interface, data Q register and address Q latch access is Input controlled. In “Low” state WR# becomes active. At rise edge the address and data are fetched. Write protection: Blanking/writing to the boot block area is input of prohibition control. Input Blanking to the boot block area and writing actuation can't be executed at the time of WP#=VIL. Ready/busy: The state of internal write state machine is output. In “Low” state it is indicated that the write state machine is in operation. If the write state machine waits for Output next operation instruction, erase is suspended or it is in deep power down state, the RY/BY# pin is in float state. Byte enable: When BYTE# is set to “Low”, the device is set to the x8 mode. At this time Input the DQ8-DQ15 pin becomes float state. Address A-1 selects high order/low order byte. When BYTE# is “High”, the device is set to the x16 mode. The A-1 input circuit is disabled. ——— Write/erase power supply: 5.0 ± 0.5V is applied during writing/erasing. ——— Device power supply: 5.0 ± 0.5V ——— Ground ——— Nonconnection
60
DV-NC55S/H DV-NC60H
• Block Diagram
DQ8-14
DQ0-7
Output Buffer
Output Buffer
Input Buffer
Input Buffer
OUTPUT MULTIPLEXER
I/O Logic
BYTE#
DATA QUEUE REGISTER
ID Register CSR
Register
CE#
ESRs CUI
A-1.0~18
OE# Data Comparator
WR# RP#
Input Buffer Y-DECODER
Y GATING/SENSING
WSM
16-KBYTE Block 31
16-KBYTE Block 30
16-KBYTE Block 1
X-DECODER
16-KBYTE Block 0
RY/BY# ADDRESS QUEUE LATCHES
Program Erase Voltage Switch
VCC GND
ADDRESS COUNTER
12-3. IC502 IX1765GE
VPP
4M EDO DRAM
Terminal
Terminal name
Function
16-19, 22-26
A0-A8
Address inputs.
14
RAS
Row address strobe.
28
UCAS
Column address strobe/upper byte control.
29
LCAS
Column address strobe/lower byte control.
13
WE
Write enable.
27
OE
2-5, 7-10
DQ1-DQ16
Data inputs/outputs.
Output enable.
31-34, 36-39 1, 6, 20
VCC
+3.3V power supply.
21, 35, 40
VSS
0V ground.
11-12, 15, 30
NC
No connection.
• Block Diagram
OE WE UCAS LCAS RAS
RAS clock generator
CAS clock generator
WE clock generator
OE clock generator
VCC VSS Data I/O Bus Column decoders Refresh counter
Sense amplifiers Y0-Y8
A0 A1 A7 A8
Address buffers and predecoders
I/O Buffer
512 16
9
Row decoders X0-X8
512
61
Memory array
I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 I/O16
DV-NC55S/H DV-NC60H
12-4. IC504 IX1687GE
MICRO COM.
PD7/D15 PD6/D14 PD5/D13 PD4/D12 PD3/D11 PD2/D10 PD1/D9 PD0/D8 PE7/D7 PE6/D6 PE5/D5 PE4/D4 PE3/D3 PE2/D2 PE1/D1 PE0/D0
Vcc Vcc Vcc Vcc Vcc Vss Vss Vss Vss Vss Vss Vss Vss
• Block Diagram
Port B Port C
Peripheral address bus
Peripheral data bus
Port F
D/A converter
A/D converter
PPG
Port 4
62
P47/AN7/DA1 P46/AN6/DA0 P45/AN5 P44/AN4 P43/AN3 P42/AN2 P41/AN1 P40/AN0
Port 2 Vref AVcc AVss
Port 1
Port 3
TPU
PA7/A23/IRQ7 PA6/A22/IRQ6 PA5/A21/IRQ5 PA4/A20/IRQ4 PA3/A19 PA2/A18 PA1/A17 PA0/A16 PB7/A15 PB6/A14 PB5/A13 PB4/A12 PB3/A11 PB2/A10 PB1/A9 PB0/A8 PC7/A7 PC6/A6 PC5/A5 PC4/A4 PC3/A3 PC2/A2 PC1/A1 PC0/A0 P35/SCK1 P34/SCK0 P33/RxD1 P32/RxD0 P31/TxD1 P30/TxD0
Port 5
SCI
P10/PO8/TIOCA0/DACK0 P11/PO9/TIOCB0/DACK1 P12/PO10/TIOCC0/TCLKA P13/PO11/TIOCD0/TCLKB P14/PO12/TIOCA1 P15/PO13/TIOCB1/TCLKC P16/PO14/TIOCA2 P17/PO15/TIOCB2/TCLKD P20/PO0/TIOCA3 P21/PO1/TIOCB3 P22/PO2/TIOCC3 P23/PO3/TIOCD3 P24/PO4/TIOCA4 P25/PO5/TIOCB4 P26/PO6/TIOCA5 P27/PO7/TIOCB5
P67/CS7/IRQ3 P66/CS6/IRQ2 P65/IRQ1 P64/IRQ0 P63/TEND1 P62/DREQ1 P61/TEND0/CS5 P60/DREQ0/CS4
WDT
RAM
Port G
PG4/CS0 PG3/CS1 PG2/CS2 PG1/CS3 PG0/CAS
DMAC
ROM *
Port 6
PF7/Ø PF6/AS PF5/RD PF4/HWR PF3/LWR PF2/LCAS/WAIT/BFEQO PF1/BACK PF0/BREQ
DTC
Bass Controller
Interruption controller
Internal data bus
H8S/2000 CPU
Internal addressbus
Clock oscillator
MD2 MD1 MD0 EXTAL XTAL STBY RES WDTOVF NMI
Port E
Port A
Port D
P50 P51 P52 P53/ADTRG
DV-NC55S/H DV-NC60H
12-5. IC508 IX1761GE Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
Terminal name VDD1 HADR0 HADR1 HADR2 HADR3 HADR4 HADR5 HADR6 HADR7 VSS VDD1 HDAT0 HDAT1 HDAT2 HDAT3 HDAT4 HDAT5 HDAT6 HDAT7 HRD HWR HAS HCS1 HCS2 VSS VDD1 HWAIT HINT VSS PDO[0] PDO[1] PDO[2] PDO[3] PDO[4] PDO[5] PDO[6] PDO[7] PDO[8] VSS VDD1 PSYCO PDRQO PDCKO VSS VDD2 DVDREQ PDCKI PDRQI PSYCI VSS VDD2
TRACK BUFFER INTERFACE I/O Supply Input Input Input Input Input Input Input Input Supply Supply In/Output In/Output In/Output In/Output In/Output In/Output In/Output In/Output Input Input Input Input Input Supply Supply Output Output Supply Output Output Output Output Output Output Output Output Output Supply Supply Output Output Output Supply Supply Input Input Input Input Supply Supply
Operation function Digital power supply +3.3V CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus Digital GND Digital power supply +3.3V CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Read signal CPU write signal CPU address strobe CPU chip select signal 1 (Track Buffer Operation) CPU chip select signal 2 (bus Voltage Transfer) Digital GND Digital power supply +3.3V CPU wait signal (Open drain) CPU interrupt signal (Open drain) Digital GND Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Digital GND Digital power supply +3.3V Output data selector sync signal Output data transfer block signal Output data transfer clock Digital GND Digital power supply +5V Request signal input Input data transfer clock Input data transfer block signal Input data selector sync signal Digital GND Digital power supply +5V
63
DV-NC55S/H DV-NC60H Pin No. 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Terminal name PDI[8] PDI[7] PDI[6] PDI[5] PDI[4] PDI[3] PDI[2] PDI[1] PDI[0] VSS VDD1 VSS VDD2 5VBUS[7] 5VBUS[6] 5VBUS[5] 5VBUS[4] 5VBUS[3] 5VBUS[2] 5VBUS[1] 5VBUS[0] NC NC VSS VDD1 5VBUFO[B] 5VBUFI[B] 5VBUFO[A] 5VBUFI[A] GPO[3] GPO[2] GPO[1] GPO[0] VSS VDD1 LI[1] LI[2] BUFO[C] BUFI[C] BUFO[B] BUFI[B] BUFO[A] BUFI[A] TEST0 TEST1 TEST2 NC MRST VSS
I/O Output Output Output Output Output Output Output Output Output Supply Supply Supply Supply In/Output In/Output In/Output In/Output In/Output In/Output In/Output In/Output – – Supply Supply Output Output Output Output Output Output Output Output Supply Supply Input Input Output Input Output Input Output Input Input Input Input – Input Supply
Operation function Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Digital GND Digital power supply +3.3V Digital GND Digital power supply +5V CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output Not Connect Not Connect Digital GND Digital power supply +3.3V 5V buffer output B 5V buffer input B (3.3V input) 5V buffer output A 5V buffer input A (3.3V input) General-purpose output terminal (CPU control) General-purpose output terminal (CPU control) General-purpose output terminal (CPU control) General-purpose output terminal (CPU control) Digital GND Digital power supply +3.3V Gate Input[1] Gate Input[2] Schmitt trigger buffer output C Schmitt trigger buffer input C Schmitt trigger buffer output B Schmitt trigger buffer input B Schmitt trigger buffer output A Schmitt trigger buffer input A Test terminal 0 (Normal: Low, Test: Hi) Function Test terminal 1 (Normal: Low, Test: Hi) RAM Test terminal 2 (Normal: Low, Test: Hi) Pin Not Connect 27MHz Input terminal Digital GND
64
DV-NC55S/H DV-NC60H
VDD2
PDI[8]
PDI[7]
PDI[6]
PDI[5]
PDI[4]
PDI[3]
PDI[2]
PDI[1]
VSS
PDI[0]
VSS
VDD1
VDD2
5VBUS[7]
5VBUS[6]
5VBUS[5]
5VBUS[4]
5VBUS[3]
5VBUS[2]
5VBUS[1]
NC
5VBUS[0]
NC
VSS
• Block Diagram
75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 VDD1
76
5VBUFO[B] 77 5VBUFI[B]
IPD Interface
78
50
VSS
49
PSYCI
48 PDRQI 47
5VBUFO[A] 79
PDCKI
Timing Gen.
46 DVDREQ
5VBUFI[A]
80
GPO[3]
81
GPO[2]
82
GPO[1]
83
GPO[0]
84
VSS
85
VDD1
86
40
VDD1
LI[1]
87
39
VSS
LI[2]
88
38 PDO[8]
BUFO[C]
89
GPO Interface
ID Detect
Error Detect
45
VDD2
44
VSS
43 PDCKO
Memory CTL
42 PDRQO 41 PSYCO
RAM (4.2Kbyte)
ZZ
37 PDO[7] 36 PDO[6]
90
BUFO[B]
91
BUFI[B]
92
BUFO[A]
93
BUFI[A]
94
32 PDO[2]
TEST0
95
31 PDO[1]
TEST1
96
30 PDO[0]
TEST2
97
NC
98
MRST
99
VSS
100
OPD Interface
BUFI[C]
ZZ
ZZ
35 PDO[5] 34 PDO[4] 33 PDO[3]
Host Interface
29
VSS
28
HINT
27 HWAIT
HADR7
VSS
HADR6
HCS2
HADR5
HCS1
HADR4
HAS
HADR3
HWR
HADR2
HRD
HADR1
HDAT7
VDD1
65
HDAT6
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
HDAT5
8
HDAT4
7
HDAT3
6
HDAT2
5
HDAT1
4
HDAT0
3
VDD1
2
VSS
1
HADR0
26
VDD1
DV-NC55S/H DV-NC60H
12-6. IC601 IX1720GE
AV DECODER
• Terminal description Name Type Description Host interface, CD-DSP interface, sub-code interface (32-pin) Reset input (active Low). When shifting from the assert state to deassert state, RESET# ID initialization process of this device is started. Stand-by input (active Low). When asserting with RESET#, all of output pins and bidirectional pins enter the float state, and this device is electrically separated from STANDBY# ID periphery. All internal operations are stopped and the power consumption is minimized. In the stand-by mode, the contents of SDRAM and setup parameter are not retained. Idle, Init, or Reset state display output (active High). It enters the active state after IDLE O(p.u.) resetting. Data bus width of the host interface is determined. It can be changed during resetting HWID ID only. The host interface of the device is set to 8 bits at the low level (GNDP) and 16 bits at the high level (VDDP). When the width is 16 bits (HWID is VDDP), byte order of the host interface data bus is determined. It can be changed during resetting only. The device is set to input/ HORD ID output m.s. byte HD at [15:8] at the low level (GNDP), and m.s. byte at [7:0] at the high level. When HWID is at the GNDP level, it is connected to GNDP. Protocol of the host bus is determined. It can be changed during resetting only. The HTYPE ID device is set to A type at the low level (GNDP) and B type at the high level (VDDP). HD[7:0] I/O 8 I.s. of the host data bus. When HWID input is connected to GNDP, only this signal (HD[7:4]) (r.t.) is defined as the host data signal. When HWID is connected to VDDP, it is used as (HD[3]) (p.u.) an 8 I.s. line of 16-bit data bus. (HD[2:1]) (r.t.) (HD[0]) (p.u.) HD[11:8] I/O When HWID is connected to VDDP, it is used as a data line 11:8 of the 16-bit host (HD[11]) (p.d.) data bus. (HD[10:8]) (r.t.) When HWID is connected to VDDP, it is used as a data line 15:12 of the 16-bit host HD[15:12] I/O(r.t.) data bus. When HWID is connected to GNDP, it is used as a the CD-DSP serial input port pin as defined below. CDCLK (HD[12]) I CD-DSP bit clock input CDDAT (HD[13]) I CD-DSP data input CDFRM (HD[14) I CD-DSP LR clock (frame) input CDERR (HD[15]) I CD-DSP data error input Host address input. The address signal specifying the physical address in this device HA[3:0] I is input. HCS# I Host chip select input. Active Low. Host protocol A type (HTYPE=GNDP): HR/W#. This input determines the direction of HWR# (HR/W#) I the host access. Host protocol B type (HTYPE=VDDP): HWR#. Host write input (active Low). Host protocol A type (HTYPE=GNDP): HDS#. Data strobe input (active Low). HRD# (HDS) I Host protocol B type (HTYPE=VDDP): HRD#. Host read input (active Low).
Glossary I AI ID r.t.
Input Analog input Input not synchronized with PCLK Retained terminal
O AO p.u.
Output Analog output Terminal internally pulled up
66
I/O AI/O p.d.
Bidirectional Analog bidirectional Terminal internally pulled down
DV-NC55S/H DV-NC60H Name Type Description Host interface, CD-DSP interface, sub-code interface (32-pin)...continued Host ready output (active High). Use this signal when the stream is transferred via the host bus. External pull-up resistor is required. Prior to transfer of each packet (1 HRDY O(p.d.) packet: length in CodBurstLen bytes), make sure that this signal is in the active state, and then bit streams of CodBurstLen byte long or shorter can be written on this device consecutively. Interrupt request (active Low). This is deasserted when the host reads the interrupt status register of this device and also when the host masks or resets the interrupt HIRQ# O(p.u.) using the interrupt mask register. When HIRQ# is not asserted, it enters the 3-state mode. (External pull-up resistor is required.) Host acknowledge output (active Low). When the protocol is A type, the device asserts this output and notifies the completion of read or write cycle. HACK# O(p.u.) When this signal is not active, it enters the 3-state mode. (External pull-up resistor is required.) When the protocol is B type, this signal functions as a wait output signal. If the high-speed host (microcomputer) is used, this signal may not have to be connected. GPI/O signal (3-pin) General-purpose bidirectional pin monitored and controlled by the ADP micro code. GPIO I/O(r.t.) After resetting, this pin is defined as an input. It can be set by using the ADP command. GPSI I General-purpose input monitored by the DVP micro code. General-purpose output controlled by the DVP micro code. After resetting, output GPSO O(p.d.) from this pin is switched to Low. PLL signal (5-pin) GCLK ID 27,000 MHz clock or crystal input for main processor. GCLK1 ID 27,000 MHz master clock input for audio. Normally, this must be connected to GCLK. Output to crystal connected to GCLK. If the crystal is not used for GCLK, nothing XO AO must be connected to XO. PLL configuration input. It can be changed only during resetting. Normally, both pins PLLCFG[1:0] ID must be connected to GNDP. Analog video port (7-pin) For CVBS, the composite video signal is output. CVBS/G/Y AO For RGB, the G signal is output. (DAC A) For YUV, the Y signal is output. For CVBS, the Y signal is output. Y/R/V AO For RGB, the R signal is output. (DAC B) For YUV, the V signal is output. For CVBS, the C signal is output. C/B/U AO For RGB, the B signal is output. (DAC C) For YUV, the U signal is output. CVBS/C AO The CVBS or C signal is selected and output. (DAC D) RSET AI Resistance load for DAC gain adjustment is inserted between GND and DAC. VREF AI Reference voltage for DAC gain adjustment is input. Composite sync output. Effective only when the RGB analog output is selected. COSYNC O(p.d.) Otherwise, it is fixed to Low. Digital video port (5-pin) VCLKx2 I/O(r.t.) Main video clock input or output. 27,000 MHz. VCLK I/O(r.t.) Divided VCLKx2 signal. Used as a qualifier of data and sync signal. HSYNC I/O(r.t.) Horizontal sync bidirectional signal pin. Its polarity and length are programmable. VSYNC I/O(r.t.) Vertical sync bidirectional signal pin. Its polarity and length are programmable. FI I/O(r.t.) Field identification bidirectional signal pin. Its polarity is programmable.
67
DV-NC55S/H DV-NC60H Name Type Digital audio port (8-pin)
Description
AMCLK
I/O(p.u.)
Audio master clock I/O. Sampling frequency can be selected among 384fs, 256fs, 192fs, and 128fs (programmable).
S/PDIF (AOUT[3])
O(p.d.)
S/PDIF transmitter output. It can be connected to DAC as the fourth audio output (AOUT [3]). After resetting, this pin outputs the low-level signal.
AOUT[2:0]
O(p.d.)
Serial output of PCM stereo audio for DAC. After resetting, this pin outputs the lowlevel signal.
AIN
I
ALRCLK
O(p.d.)
ABCLK
O(p.d.)
Serial input of PCM stereo audio for ADC. LR clock output of AOUT [4:0] and AIN. The square wave is formed with the sampling frequency. The LR polarities are programmable. Bit clock output of AOUT [4:0] and AIN. AOUT is output to this clock in the leading and trailing edges (programmable) and AIN is latched.
DVD-DSP interface (13-pin) DVDREQ DVDVALID DVDSOS DVDDAT[7:0] DVDSTRB DVDERR
O(p.d.) I I I ID I
DVD-DSP data request output (polarity programmable). DVD-DSP data effective input (polarity programmable). DVD-DSP data sector start input (polarity programmable). DVD-DSP data input bus. DVD-DSP data bit strobe (clock) input. Polarity programmable. DVD-DSP error input. Polarity programmable.
SDRAM interface (35-pin) RAMDAT [15:0] I/O(r.t.)
SDRAM bidirectional data bus.
RAMADD [11:0] RAMRAS#
O(p.d.) O(p.u.)
SDRAM address bus output. SDRAM row selection (active Low) output.
RAMCAS# PCLK
O(p.u.) O(p.d.)
SDRAM column selection (active Low) output. SDRAM clock output (same as the internal processing clock).
RAMDQM RAMCS0# RAMCS1#
O(p.d.) O(p.u.) O(p.u.)
SDRAM data masking (active High) output. SDRAM chip select (active Low) output. Lower 2 Mbyte device. SDRAM chip select (active Low) output. Upper 2 Mbyte device.
RAMWE# TEST signal (pin 3)
O(p.u.)
SDRAM write enable (active Low) output.
SCNENBL TESTMODE
ID ID
Test pin. Normally connected to GNDP. Test pin. Normally connected to GNDP.
ICEMODE Power signal (49-pin)
ID
Test pin. Normally connected to VDDP.
GNDP VDDP
S S
Ground for 3.3V digital power supply. 3.3V digital power supply
VDDIP GNDAAM
S S
3.3V digital power supply Ground for PLL power supply for 3.3V AMCLK generation.
VDDAAM GNDC
S S
PLL power supply for 3.3V AMCLK generation. Ground for 1.8V digital power supply.
VDDC GNDA
S S
1.8V digital power supply. Ground for PLL power supply for 1.8V internal clock generation.
VDDA VDDD
S S
PLL power supply for 1.8V internal clock generation. Analog power supply for 3.3V video DAC.
GNDDAC [D,B,P,S]
S
Ground for Analog power supply for 3.3V video DAC.
68
DV-NC55S/H DV-NC60H
90
100
80
130
70
TOP VIEW
140
60
150
50
40
30
20
10
1
160
HORD HWID VDDP HTYPE HD15/CDERR HD14/CDFRM HD13/CDDAT HD12/CDCLK HD11/TCK GNDP HD10/TMS VDDC HD9/TDO GNDC HD8/TDI VDDP HD7 HD6 VDDIP HD5 HD4 HD3 HD2 HD1 HD0 VDDP HA3 HA2 HA1 HA0 HWR#/HR/W# HCS# VDDC HRD#/HDS# GNDC HRDY HIRQ# VDDP HACK# GNDP
VDDA STNDBY# GNDA RESET# SCNENBL VDDP VCLKx2 GNDP TESTMODE VDDAAM AMCLK GNDAAM S/PDIF/AOUT3 GPIO VDDP AOUT0 AOUT1 AOUT2 ALRCLK VDDP ABCLK VDDC GPSO GNDC GPSI GNDP DVDERR DVDSOS DVDVALID DVDSTRB DVDREQ DVDDAT0 DVDDAT1 DVDDAT2 DVDDAT3 DVDDAT4 DVDDAT5 DVDDAT6 DVDDAT7 IDLE
110
120
GCLK XO PLLCFG0 GCLK1 VDDC PLLCFG1 GNDC AIN ICEMODE VREF GNDDAC_S GNDDAC_P RESET GNDDAC_B C/B/UDAC_C Y/R/VDAC_B VDDD CVBS/C/DAC_D CVBS/G/Y/DAC_A GNDDAC_D COSYNC VDDIP VDDP GNDP FI HSYNC VDDP VSYNC VCLK RAMDAT0 RAMDAT15 VDDP RAMDAT1 RAMDAT14 GNDP RAMDAT2 RAMDAT13 VDDP RAMDAT3 RAMDAT12
• Block Diagram
69
GNDP RAMDAT4 RAMDAT11 VDDP RAMDAT5 RAMDAT10 RAMDAT6 GNDC RAMDAT9 VDDP RAMDAT7 GNDP RAMDAT8 VDDP PCLK GNDP RAMDQM VDDC RAMWE# RAMCAS# RAMRAS# RAMCS1# VDDP RAMCS0# GNDP RAMADD11 RAMADD9 RAMADD10 VDDP RAMADD8 RAMADD0 GNDP RAMADD7 RAMADD1 RAMADD6 RAMADD2 VDDP RAMADD5 RAMADD3 RAMADD4
DV-NC55S/H DV-NC60H
12-7. IC602-3 IX0751TA 16M SDRAM Pin No. 35 34 18 19 20~24 27~32 17, 16, 15
Terminal Name CLK Clock
Name
CKE
Clock Enable
CS BA A0~A10
Chip Select Bank Address Address
Input Function The system clock input. All other inputs are referenced to the SDRAM on the rising edge of CLK. Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh. Command input enable or mask except CLK, CKE and DOM Select either one of banks during both RAS and CAS activity. Row Address: RA0~RA10, Column Address: CA0~CA7
RAS, CAS, WE Row Address Strobe, Column Address Strobe, Write Enable 14, 36 LDQM, UDQM Data Input/Output Mask 2, 3, 5, I/O0~15 Data Input/Output 6, 8, 9, 11, 12, 39, 40, 42, 43, 45, 46, 48, 49 VDD/VSS Power Supply/Ground 1, 25, 26 4, 7, 10, VDDO/VSSO Data Output Power/Ground 13, 38, 41, 44, 47, 50 33, 37 NC No Connection
RAS, CAS and WE define the operation. Refer function truth table for details. DQM control output buffer in read mode and mask input data in write mode. Multiplexed data input/output pin
Power supply for internal circuit and input buffer. Power supply for DO No connection
• Block Diagram
Row Decoder
Ref. Addr.[0:11]
Address[0:10]
Refresh Counter
Audio/Self Refresh
Refresh Interval Timer
Row Addr. Latch/Predecode
Self Refresh Counter
512Kx16 Bank 0
Sense AMP & I/O gates Column Decoder
Precharge
CKE
CS RAS CAS
Row Active
State Machine
BA(A11)
Address Register
Column Active Burst Length Counter
Column Addr. Latch & Counter Overflow
WE UDQM
Data Input/Output Buffers
CLK
Column Decoder Sense AMP & I/O gates
Row Addr. Latch/Predecode
LDQM
Mode Register
512Kx16 Bank 1
Test Mode
70
I/O Control
I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15
DV-NC55S/H DV-NC60H
12-8. IC701 TC94A03F Pin No. Terminal Name In/Output 1 ASLCN Output 2 ASLCO Output
SERVO/DATA PROCESSOR
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
DVSS RO DVDD DVR LO DVSS XVSS XI XO XVDD TESM0 TESM1 TESM2 VDD3 VSS3 VPFC
– Output – Output Output – – Input Output – – – – – – Output
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
TEST0 VLPFI VLPFO VSS3 MON0 MON1 MON2 MON3 MON4 MON5 MON6 MON7 MON8 MON9 VDD3 NC NC TEST1 FLGA FLGB VSS3 /RST /MA /MRD /MWR /MCE /MINT MD0 MD1 MD2 MD3 MD4 MD5 MD6 MD7 VDD5
Input Input Output –
Operation function 3/5V system Data slice negative pole output 3V system Analog data slice output 3V system (Digital slice output enabled at differential input) Ground for DAC only – R-ch output signal 3V system Power supply for DAC only 3V system Amplifier reference signal output 3V system L-ch output signal 3V system Ground for DAC only – Ground for oscillator only – Crystal oscillation input 3V system Crystal oscillation output 3V system Power supply for oscillator only – Test terminal 3V system Test terminal 3V system Test terminal 3V system 3.3V digital power – 3.3V digital ground – Clock PLL system phase/frequency 3V system comparative output Test mode terminal 3V system VCO system filter input for clock PLL 3V system VCO system filter output for clock PLL 3V system 3.3V digital ground –
Output
Test monitor
–
Analog output terminal Analog input terminal Analog output terminal
Analog input terminal Analog output terminal Connected to GND OPEN Connected to VDD3
Analog output terminal Connected to VDD3 Analog input terminal Analog output terminal
3V system
3.3V digital power
–
–
–
Input In/Output In/Output – Input Input Input Input Input Output
Test mode terminal General-purpose I/O or flag monitor General-purpose I/O or flag monitor 3.3V digital ground Reset terminal Microcomputer address enable signal Microcomputer data read signal Microcomputer data write signal Microcomputer chip enable signal Microcomputer interrupt signal
3V system 5V system 5V system – 5V system 5V system 5V system 5V system 5V system 5V system
In/Output
Microcomputer data buss
5V system
–
Remarks Analog output terminal Analog output terminal
5V power supply
–
71
Connected to VDD3
Pull-up resistor built in Fail-safe terminal Fail-safe terminal Fail-safe terminal Fail-safe terminal Open drain terminal
DV-NC55S/H DV-NC60H Pin No. 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110
Terminal Name In/Output NC – NC SMCK Output VMCK Output VDD3 PD0 VSS5 PD1 PD2 PD3 PD4 VSS3 PD5 PD6 PD7 PD8 /PSYC /PDRQ PDCK VDD5 TESM3 DIGI TESM4 VDD3 BA0 BA1 BA2 BA3 VSS5 BA4 BA5 BA6 BA7 BA8 VDD3 /BOE /BRAS /BCAS /BCASL /BWE VDD5 BD0 BD1 BD2 BD3 BD4 BD5 BD6 BD7 BD8 VSS3 BD9 BD10 BD11 BD12 VSS5
Operation function
3/5V system – 5V system 5V system
– Output –
22M system clock output Data output system (signal processing system) clock output 3.3V digital power supply DVD/CD data output 5V ground supply
Output
DVD/CD data output
5V system
–
3.3V digital ground
– 5V system –
–
Output
DVD/CD data output
5V system
Output Output Output – – Input – –
DVD data sector sync signal DVD data transfer block DVD data transfer block 5V power supply Test terminal 1 bit DAC digital IN input Test terminal 3.3V digital power supply
5V system 5V system 5V system – 5V system 5V system 5V system –
Output
External RAM address output
5V system
–
5V ground supply
–
Output
External RAM address output
5V system
– Output Output Output Output Output –
3.3V digital power supply External RAM/OE signal External RAM/RAS signal External RAM/UCAS signal External LCAS/WE signal External RAM WE signal 5V power supply
– 5V system 5V system 5V system 5V system 5V system –
External RAM data I/O
5V system
In/Output
– In/Output –
Remarks
3.3V digital ground
–
External RAM data I/O 5V ground supply
5V system –
72
Connected to VSS5 Connected to VDD5
DV-NC55S/H DV-NC60H Pin No. 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125
Terminal Name In/Output BD13 BD14 In/Output BD15 NC – NC VDD3 – PLCK In/Output TESM5 – TESM6 – TESM7 – TESM8 – VSS3 – CFC1 Output CFC2 Output PPW Output
126
PESV
Input
127 128
PVSS PESP
– Output
129
PDOP1
Output
130
PDON1
Output
131
PDOP2
Output
132
PDON2
Output
133 134 135
LPFN LPFO PVREF
Input Output –
136 137 138 139
VCOREF VCOF PVDD RFOn
140 141 142
TESM9 TEST2 RFCD
– Input Input
143
RFDVD
Input
144 145
AVDD RFCT
– Input
146 147
RFZI TEZI
Input Input
148 149 150 151 152 153 154 155
AWIN AVSS FEI TEI LVL RFRP AVSS TESM10
Input – Input Input Input Input – –
Input Input – In/Output
Operation function External RAM data I/O
3/5V system
Remarks
5V system –
3.3V digital power supply PLL system clock I/O Test terminal Test terminal Test terminal Test terminal 3.3V digital ground VCO frequency control signal VCO frequency control signal Phase comparator offset adjustment voltage output Phase comparator offset adjustment signal input Ground for 3.3V PLL system only Phase comparator offset adjustment signal output DVD/CD phase control signal (positive polarity) DVD/CD phase control signal (negative polarity) DVD/CD phase control signal (positive polarity) DVD/CD phase control signal (negative polarity) Data PLL low-pass filter inversion input Data PLL low-pass filter output Reference power supply for data PLL system only VCO reference VCO self-adjusting filter output Power supply for 3.3V PLL system only Data slice 6-bit DAC output (RFOn input enabled at differential input) Test terminal Test mode terminal CD RF signal input (RFOp input enabled at differential input) DVD RF signal input (RFOp input enabled at differential input) Power supply for 3.3V analog system only RFRP center voltage output (zero cross import) RFRP zero cross signal input Tracking error signal input (zero cross import) Active wide PLL control signal input Ground for 3.3V analog system only Focus error signal input Tracking error signal input RF level or sub beam signal add input RFRP signal input Ground for 3.3V analog system only Test terminal
73
– 3V system 3V system 3V system 3V system 3V system – 3V system 3V system 3V system
Analog output terminal Analog output terminal Analog output terminal
3V system
Analog input terminal
– 3V system
Analog output terminal
3V system
Analog output terminal
3V system
Analog output terminal
3V system
Analog output terminal
3V system
Analog output terminal
3V system 3V system 3V system
Analog input terminal Analog output terminal
3V system 3V system – 3V system
Analog input terminal Analog input terminal
3V system 3V system 3V system
OPEN Connected to VDD3 Analog input terminal
3V system
Analog input terminal
– 3V system
OPEN
3V system 3V system
Analog input terminal Analog input terminal
3V system – 3V system 3V system 3V system 3V system – 3V system
Analog input terminal
Connected to GND Connected to GND OPEN OPEN
Analog output terminal
Analog input terminal Analog input terminal Analog input terminal Analog input terminal Connected to VREF
DV-NC55S/H DV-NC60H Pin No. Terminal Name In/Output 156 EXTAD Input 157 VREF – 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175
FOO TRO AVDD AWCTL FMO DMO TEBC FEBC DPDC EQBC ANMON /DFCT VRCK VSS3 SCD SCL SCB FGIN
Output Output – Output Output Output Output Output Output Output Output Output Output – Output Output Output Input
176
ASLCP
Output
Operation function General-purpose external ADC input Reference power supply for analog system only: 1.65V Focus EQ output Tracking EQ output Power supply for 3.3V analog system only Active wide PLL control output Feed EQ output Disc EQ output Tracking balance control signal Focus balance control signal DPD error signal/pit depth adjustment signal RF wide boost adjustment signal General-purpose PWM output Black dot detection signal RF EQ property control clock 3.3V digital ground Head amplifier serial data Head amplifier serial data latch pulse Head amplifier serial data clock Disc FG signal input (with self-bias circuit) Data slice positive pole output
3/5V system Remarks 3V system Analog input terminal 3V system 3V system 3V system – 3V system 3V system 3V system 3V system 3V system 3V system 3V system 3V system 3V system 3V system – 3V system 3V system 3V system 3V system
Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal
Feedback resistor Analog input terminal Analog output terminal
Note) Terminals with "/" at the beginning of their names are active "L" ones.
• Block Diagram
Digital in
to Driver, RFamp
DAC
DAC I/F
Servo signal from RFamp
ADC
DEQ
Analog out
1bit DAC for CD-DA
Clock PLL
Servo Control
Digital Servo Micom BUS
RF signal from RFamp
Data Slicer
PLL
Slice level Gen.
Syndrome operation
ECC
SYNC Det. Demodulation
DRAM I/F
to DRAM
to RFamp
74
Micom I/F
Output I/F
to Micom
to DECORDER
DV-NC55S/H DV-NC60H
12-9. IC702 IX3420CE
4M EDO DRAM
Terminal
Terminal name
16-19, 22-26
A0-A8
Address inputs.
Function
14
RAS
Row address strobe.
28
UCAS
Column address strobe/upper byte control.
29
LCAS
Column address strobe/lower byte control.
13
WE
Write enable.
27
OE
Output enable.
2-5, 7-10
DQ1-DQ16
Data inputs/outputs.
VCC
+3.3V power supply.
21, 35, 40
VSS
0V ground.
11-12, 15, 30
NC
No connection.
31-34, 36-39 1, 6, 20
• Block Diagram OE WE UCAS LCAS RAS
RAS clock generator
CAS clock generator
WE clock generator
OE clock generator
VCC VSS Data I/O Bus Column decoders Refresh counter
Sense amplifiers Y0-Y8
9 A0 A1 A7 A8
Address buffers and predecoders
Row decoders X0-X8
I/O Buffer
512 16
Memory array
512
75
I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 I/O16
DV-NC55S/H DV-NC60H
12-10. IC5001 PT6312LQ FL DRIVER Pin No. 1-4 5
Terminal name SW1 to SW4 DOUT
I/O I O
6
DIN
I
7, 43 8
GND CLK
– I
9
STB
I
10-13
K1 to K4
I
14, 38 15-20
VDD SG1/KS1 to SG6/KS6 SG7 to SG11 SG12/GR11 SG13/GR10 to SG16/GR7 VEE GR6 to GR1 LED1 to LED4 OSC
– O
21-25 26, 28-31
27 32-37 42-39 44
O
Operation function General purpose input pins Data output pin (N-Channel, Open-Drain) This pin outputs serial data at the falling edge of the shift clock (starting from the lower bit). Data input pin This pin inputs serial data at the rising edge of the shift clock (starting from the lower bit) Ground pin Clock input pin This pin reads serial data at the rising edge and outputs data at the falling edge. Serial interface strobe pin The data input after the STB has fallen is processed as a command. When this pin is "HIGH", CLK is ignored. Key data input pins The data inputted to these pins are latched at the end of the display cycle. Logic power supply High-voltage segment output pins also acts as the key source High voltage segment output pin High voltage segment/grid output pins
O – O O I
Pull-down level High-voltage grid output pins LED output pin Osillator input pin A resistor is connected to this pin to determine the oscillation frequency.
• Block Diagram
Control DIN 6 DOUT 5 CLK 8
Serial Data Interface
STB 9
Display Memory (16bits x 11 Words)
Segment Driver/ Grid Driver/
VDD R 44
OSC
Key Scan Output
Timing Generator
15 16 17 18 19 20 21 22 23 24 25
SG1/KS1 SG2/KS2 SG3/KS3 SG4/KS4 SG5/KS5 SG6/KS6 SG7 SG8 SG9 SG10 SG11
OSC 26 SG12/GR11 28 SG13/GR10
SW1 1 SW2
2
SW3 3
General Input Register
Key Matrix Memory
29 SG14/GR9 30 SG15/GR8
SW4 4
31 SG16/GR7
LED1 42 LED2 41 LED3 40
LED Driver Grid Driver
LED4 39 Dimming Circuit 14, 38 7, 43 10 11 12 13 K1 K2 K3 K4
VDD
76
GND
27 VEE
37 36 35 34 33 32
GR1 GR2 GR3 GR4 GR5 GR6
DV-NC55S/H DV-NC60H
12-11. IC6001 PCM1737 AUDIO DAC Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
Terminal name LRCK DATA BCK CLKO SCLK DGND VDD TEST1 TEST2 VCCR AGNDR VCOMR VOUTR AGND VCC VOUTL VCOML AGNDL VCCL NA NA RST ZEROL ZEROR MDO MDI MC ML
I/O I I I O I – – I I – – – O – – O – – – I I I O O O I I I
Operation function LRCK clock input (fs) (1) Audio • Data input (1) Bit clock input for data. (1) System clock buffered output. System clock input. Digital ground. Digital power supply +3.3V Test pin (2) (Open or ground) Test pin (2) (Open or ground) Rch, Analog power supply +5V Analog ground, Rch Rch Analog output amp. • common Rch Analog voltage output. Analog • ground Analog power supply +5V Lch Analog voltage output Lch Analog output amp • common Analog ground, Lch Lch, Analog power supply +5V Not connected. Not connected. Reset Lch, Zero data • flug Rch, Zero data • flug Mode control, data output (3) Mode control, data input (2) Mode clock (2) Mode latch (2)
Note: (1) Schmidt trigger input, 5V logic input possible. (2) Schmidt trigger input pull-down resistor. 5V logic input possible. (3) Try state output
• Block Diagram
BCK LRCK
Sirial I/F
DATA
x8 (x4) Oversampling Dijital Filter + Mulcher Function Controller
TEST1 TEST2 RST ML
VOUTL
CR LPF + Output Amp
DAC
VCOML
Mulcher Level Data-Sigma Modulator
Function Control
VOUTR
CR LPF + Output Amp
DAC
MC
VCOMR
MDI MDO NA
System Clock
NA
VCCR
AGNDR
VCCL
AGNDL
VCC
VDD
DGND
ZEROR
77
AGND
Power Supply.
Zero detection
ZEROL
Clock Manager
CLKO
SCLK
DV-NC55S/H DV-NC60H
12-12. IC7701 BA5984FP Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Terminal name LD-FWD SL_IN(+) SL_IN(-) SLOUT SP_IN(+) SP_IN(-) SP_OUT VCC LD(-) LD(+) SPIN(-) SPIN(+) SL(-) SL(+)
MOTOR DRIVER
Operation function Pin No. Loading driver FWD input terminal 15 CH1 Former stage amplifier nonreverse input terminal 16 CH1 Former stage amplifier reverse input terminal 17 CH1 Former stage amplifier output terminal 18 CH2 Former stage amplifier nonreverse input terminal 19 CH2 Former stage amplifier reverse input terminal 20 CH2 Former stage amplifier output terminal 21 Power terminal 22 Loading driver Negative output 23 Loading driver Positive output 24 Driver CH2 Negative output 25 Driver CH2 Positive output 26 Driver CH1 Negative output 27 Driver CH1 Positive output 28
Terminal name V04(+) V04(-) V03(+) V03(-) GND BIAS MUTE FO_OUT FO_IN(-) FO_IN(+) TR_OUT TR_IN(-) TR_IN(+) REV
Operation function Driver CH4 Negative output Driver CH4 Positive output Driver CH3 Negative output Driver CH3 Positive output Ground terminal Bias input terminal Mute control terminal CH3 Former stage amplifier output terminal CH3 Former stage amplifier reverse input terminal CH3 Former stage amplifier nonreverse input terminal CH4 Former stage amplifier output terminal CH4 Former stage amplifier reverse input terminal CH4 Former stage amplifier nonreverse input terminal Loading driver REV input terminal
Note 1: Positive and negative output the driver have polarity with respect to input. (An example: 4 pin terminal voltage ‘HIGH’: 14 pin terminal voltage ‘HIGH’)
• Block Diagram 26
25
24
23
22
21
20
REV OUTF FWD OUTR
16K
10K
10K
10K +
16K
-
15 10K 10K
10K
10K
+
Level Shift
-
+ -
10K
16
+
+
17 +
+
+
10K Loading Driver
18
10K
MUTE 10K
19
+
27
+
28
+
Level Shift
Level
- Shift + 16K
10K
+ -
Level
- Shift + 16K
2
3
4
5
6
7
8
78
10
11
12
+
+
9
+
1
+
+
+
10K
10K
10K
10K
10K
10K VCC
10K 13
10K 14
DV-NC55S/H DV-NC60H
12-13. IC8201 IX1757GE INTERFACE MICOM. • Terminal description Pin No.
Terminal Name
In/Output
1 2
TRAY ACK(L) DVD LED(L)
Input Output
3
DUB LED(L)
Output
4
STANDBY LED(L)
Output
Operation function Input terminal of [TRAY ACK] from DVD microcomputer DVD LED control terminal It outputs [L] and is lit during DVD output. VTR ← DVD LED control terminal It outputs [L] and is lit in VTR ← DVD mode. Stand-by LED control terminal It outputs [L] and is lit during stand-by. IC test terminal. Fixed to GND.
5
TEST
Input
6
XIN
Input
Radiator connection terminal
7 8
VSS XOUT
– Output
Digital GND Radiator connection terminal
9
VDD
10 11
R/C RESET
12
NC
13 14
POWER KEY OPEN/CLOSE KEY
15
EA
16
POWER OFF
Output
17
POWER ON
Output
VTR POWER ON key control terminal It outputs [H] when the power is ON. VTR TIMER mode detection terminal
– Input Input –
Power AT_5V Remote control signal input Microcomputer reset signal input Unconnected
Input Input
POWER key input: [L] input while key is ON. OPEN/CLOSE key input: [L] input while key is ON.
Input
Terminal for IC only. Fixed to power supply.
18
TIMER MODE
Input
19
POWER MODE
Input
VTR POWER OFF key control terminal It outputs [H] when the power is OFF.
When [H] is output, the VTR power ON/OFF is not controlled. VTR POWER mode detection terminal When [TIMER MODE] = [L], DVD is turned ON when the [POWER MODE] is activated and turned OFF when it is deactivated. 20 21~31
REC MODE NC
Input –
VTR REC mode detection terminal [VTR ← DVD] key is disabled at [H] input. No used
32 33
P-CON(L) SHORT DET(L)
Output Input
DVD P-CON control terminal Short circuit detection terminal for DVD P-CON power supply
34 35
NC A_OUT_MUTE(L)
– Output
Unconnected Sound output mute control terminal for VTR/DVD common terminal
36
DVD(H)
Output
Output switching control terminal for VTR/DVD common terminal
37 38~40
DUB(H) NC
Output –
Input switching control terminal for VTR input 1 No used
After [L] is input for 0.5 seconds, P-CON is switched to OFF.
41
PLAY MODE(L)
Input
DVD PLAY mode detection terminal When [TIMER MODE] = [H] and [PLAY MODE] = [L], DVD is not turned OFF even if the [POWER MODE] is deactivated.
42
STANDBY REQUEST(L)
Output
Control terminal for POWER OFF request to DVD microcomputer
43
TRAY REQUEST(L)
Output
It keeps outputting the request until [STANDBY ACK] = [L] is input. Control terminal for TRAY operation request to DVD microcomputer
44
STANDBY ACK(L)
It keeps outputting the request until [TRAY ACK] = [L] is input. Input
Input terminal for [STANDBY ACK] from DVD microcomputer
79
RESET
XOUT
XIN
SYSCLK
CLK GEAR, TBT
fs
fc
80 ROM 16KB
RAM 512B
CPU
STANDBY CONTROLLER
OSC
LOW FREQ OSC
HIGH FREQ OSC
DVO
WDT
TI0, TI1
TO0
ch. 0
Port 3
P37~P30
P17~P10
A8~A15
SCK, SI, SO
P07~P00
Port 09
AD0~7
EXTERNAL BUS CONTROLLER
SERIAL INTERFACE
ch. 1
RXD, TXD
Port 4
P47~P40
UART ch. 0
RD, WR, ALE, WAIT, CLK
ch. 1
8bit TMR
INTREQ
Port 1
ETC0
TO1
INTERRUPT CONTROLLER
16-bit Expansion Timer
STOP
Port 2
P22~P20
EA
DV-NC55S/H DV-NC60H
• Block Diagram
DV-NC55S/H DV-NC60H
-MEMO-
81
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
13. BLOCK DIAGRAMS 13-1. SYSTEM SERVO BLOCK DIAGRAM J
I
FROM INTERFACE BLOCK (FROM PIN 37 OF IC8201)
DUB(H)
DUB(H)
H
G
(TO BASE OF Q503, Q302 AND Q205)
F
E
EJECT/STOP
D
REW REW
/STOP
C
B
A
1
2
3
4
5
6
7
8
9
10
11
82~83
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
13-2. MAIN BLOCK DIAGRAM J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
84~85
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
13-3. SIGNAL FLOW BLOCK DIAGRAM J
EE Signal
PB Luminance Signal PB Chrominance Signal
REC Luminance Signal REC Chrominance Signal
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
86~87
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
13-4. AUDIO BLOCK DIAGRAM J
EE Signal
PB Signal
REC Signal
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
88~89
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
13-5. POWER BLOCK DIAGRAM J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
90~91
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
14. SCHEMATIC DIAGRAMS 14-1. DVD MAIN (1) CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
92~93
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
14-2. DVD MAIN (2) CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
94~95
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
14-3. VCR DISPLAY CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
96
7
8
9
10
DV-NC55S/H DV-NC60H
14-4. DVD DISPLAY CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
10 1
11 2
12 3
13 4
14 5
15 6
97
16 7
17 8
18 9
19 10
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
14-5. AV CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
98~99
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
14-6. TERMINAL CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
100~101
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H å AND SHADED COMPONENTS=SAFETY RELATED PARTS
14-7. POWER CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
102~103
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
14-9. VCR MAIN (1) CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
106~107
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
14-10. VCR MAIN (2) CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
108~109
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H å AND SHADED COMPONENTS=SAFETY RELATED PARTS
14-11. VCR MAIN (3) CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
å
C
B
A
1
2
3
4
5
6
7
8
9
10
11
110~111
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
14-12. VCR MAIN (4) CIRCUIT SCHEMATIC DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
112~113
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
15. PRINTED WIRING BOARD ASSEMBLIES DVD MAIN PWB Component Side SIDE A J
Q308
I
TP7711TP7710TP7709 TP7708TP7707TP7706
C308
TP7705TP7704TP7703 TP7702TP7701
Q309
C213
C310
CN701
C321
FD4
CN702
C322
C313
C314
C320
C316
C337
TP323 R311 TP321 R328
R327
R336 R335
R7736
TP319
TP835
C780
C207
TP839
C7703
TP316
IC301
TP331 TP332
R7739
TP838
TP317
R340
C326
R332
C325
R331
TP315 TP314 TP313 TP312
IC7701
C208
TP311
R330
C324
CN301
C214
R333
R780
C206
TP837
C327
R7740
C303
R334
TP836
H
TP322
C302
R7725
R7729
C7707
C7702
R7721
R7714
R7713
R7711
FB602
R7709
CN201
C328
TP333
TP833 TP834
TP320 R341
C309
R342
C212
C323
TP832
R7701
R7704
C209
C211
C210
C318
C338
TP831 TP318
TP310 R329
TP309 R337
R7708 R339
TP308
C317
TP307
R317
R338
R343
TP306 TP305
R316
C315
R344
L302
R7732
R7730
C7705
R7726
R7724
C7704
R7717
R7722
G
R7712
R7710
Z3
C329
TP304 C301
C330
R7707
TP303 TP302 TP301
L301 R325 R326 R691 TP602 CN601
IC702 C752
TP603 TP601 C502
Z4
FB607
F
TP503 R524
R521
R535
R537
R525
R531
C507
C506
R522
FL501
R518
R517
R520
R514 L501
R513
R516
R570
R528
R519
R534
C526
R505
R506
C510
R544
C511
FB605
C505
C631
TP502
R616
C604
R617
R619
C629 R618
C602
R557
R620
C504
TP823
R621
R509
R508
R529
Q503
TP501
C508 TP824
C501
TP820
L602
C632
C633
C634
TP606 TP608
C630
TP604
C627
TP821
R622
R545
R567
C503
FB816
TP605 TP607
IC504
TP822
C635
R510
R511
R558
Q502
E
C601
R543
R507
C603
R540
C509
X601
TP819
R816
C626
R612
TP817 TP816
R613
R817
D
R501
TP818
TP815
R541
R550
R502
R504
R815
CN801
TP813
R533
CN803 TP814
R539 R538
R503
FB604
TP841
R602
R556
R542 TP812
R604
C605
TP811 TP810
R605
FB807 TP809 R551
TP808 TP807
C625
R552
R603
R806
TP806 TP805
IC601 C606
R805
C623
TP804 TP840
R804 C607
TP803
CN802
C
C622
R803 TP802 R802
IC501
TP801
R801
C608
R826 R825 C621
C616
C614
C615
C613
R601
C612
C517
C610
R555
FD2
C611
C609
B
A
1
2
3
4
5
6
114
7
8
9
10
DV-NC55S/H DV-NC60H
Wiring Side SIDE A J
I
H
G
F
E
D
C
B
A
1 10
2 11
3 12
4 13
5 14
6 15
115
7 16
8 17
9 18
10 19
DV-NC55S/H DV-NC60H
Component Side SIDE B J
Q304 R7734
FB301
R322
C307
R314
C331
CN302
I
FD1 R532
C7706
IC7702
R323 Q302
C707
R321
Q701
C716
C706
R708
C709
C710
C718
R713
C719
R724
C720
R726
C715
C781
C721
C722
C723
C724
C725
C726
C727
R743
R746
R745
IC705
C739
R744
R704
R741
R705
R748
R747
C741
C742
G
C738
R742
C740
C733
C311
Q303
C737
R739
C703
C732
R345
R319
R737
R740
C702
R346
R738
R701
C708
R702
R703
R721
R723
C711
C735
C730
C713
R722
R709
R710
R729
R711
R730
R731
R733
R732
R735
R734
R736
R725
R718
R719
R720
C333
C332
C319
R716
Q307
TP701
C705
C714
R303
TP712 C306
R768
C304
C728
L701
R728 R304
L702
C734
C712
R727
D301
R714
C729
C717
Q301
H
R707
R769
R767
R717
R715
C731
Q702
R712
R315
C305
R310
C704 R320
C701 R749
C743
R753
R752
C745
R706
R756 CN703
R759
R757
R758
C749
C747
R760 C748
R750
C746
R755
C312
C744
R754
FL701
R751
R318
IC701
TP702 TP703 TP704 TP705 TP706 TP707 TP708 TP709 TP710
F
C664
TP711
R761
C750
R512
C665
R762
C751
IC604
R763 R764
C662
R530
R765 TP714 C759
C758
C512
C756
C753
C663
TP713
C661
IC507
D501
R515
E
C757
C522
IC503 R568
C528
C624
C523
TP506 TP505 TP504
C529
C521 R566
TP507
FB817
C519
R828
FB814
TP508
FB813
IC508
TP509
R692 R693
C527
R523
C524
D
R615
FB815
C520
R563
R564
C628
L601
R569 C525
FB812 TP510 FB811
C205 R565
TP511 R814
IC603 TP513 R561
R812 R562
C643
C644
C202
R224
R827
Q501
R813
FB810
Q201
R536
R819
TP826
R818
TP825
R609
R608
R611
R610
R559
C
R824
R560
R606 TP827
Z2
FB809
R607
R820
FB808 FB806
TP830
R823
C204
R225
TP829
R822
C203
R226
TP828
R821
Q202
IC502 IC602 Z1
C516
C515
Q203
Q205 C617
R227
B
C201 C640
FD3
C641
R571
C620
C646
FB603
C619
C618 FB601
A
1
2
3
4
5
6
116
7
8
9
10
DV-NC55S/H DV-NC60H
VCR DISPLAY PWB Component Side SIDE A J
I
H
Wiring Side SIDE A
G
F
Component Side SIDE B E
D
C
Wiring Side SIDE B
B
A
1
2
3
4
5
6
118
7
8
9
10
DV-NC55S/H DV-NC60H
DVD DISPLAY PWB Component Side SIDE A J
I
H
Wiring Side SIDE A
G
F
Component Side SIDE B E
D
C
Wiring Side SIDE B
B
A
1 10
2 11
3 12
4 13
5 14
6 15
119
7 16
8 17
9 18
10 19
DV-NC55S/H DV-NC60H
AV PWB Component Side SIDE A J
I
H
G
F
Wiring Side SIDE A E
D
C
B
A
1
2
3
4
5
6
120
7
8
9
10
DV-NC55S/H DV-NC60H
Component Side SIDE B J
R2014
C2003
Q2316
R2013
Q2014 R2326
Q2006
R6060
R2341
I
R6061
R6067
R6066
R6062
Q2309
R6063
Q2311
R6064
Q2310
R6065
C2015 Q2315 Q2313 IC2002 R2340
R6075
R2339
Q2005 IC6010
R6161 R6160
RJ101 Q2317
R6167
R6166
R6163
R6162
R6164
R6165
IC2004
C2002
R6068 R6175
JP6001
IC6110
R2001 R2003
R2008
R2007
R2010
H
R6076
C2018
IC2001
Q2003
R6176 IC6011
Q6010 Q2001
R2005
R2009
C2019 R2004
Q6110
JP6002
R6072
Q2004
R6070
R6074
R2002
R2011
Q2002 IC2003
R2012
R6069 Q6012
Q2007
Q6011 R6071
R2006
R6073
G
F
Wiring Side SIDE B E
D
C
B
A
10 1
11 2
12 3
13 4
14 5
15 6
121
16 7
17 8
18 9
19 10
DV-NC55S/H DV-NC60H
TERMINAL PWB Component Side SIDE A J
I
H
G
F
Wiring Side SIDE A E
D
C
B
A
1
2
3
4
5
6
122
7
8
9
10
DV-NC55S/H DV-NC60H
Component Side SIDE B J
I
H
G
F
Wiring Side SIDE B E
D
C
B
A
10 1
11 2
12 3
13 4
14 5
15 6
123
16 7
17 8
18 9
19 10
DV-NC55S/H DV-NC60H
POWER PWB Component Side SIDE A J
I
H
G
F
Wiring Side SIDE A E
D
C
B
A
1
2
3
4
5
6
124
7
8
9
10
DV-NC55S/H DV-NC60H
Component Side SIDE B J
I
H
G
F
Wiring Side SIDE B E
D
C
B
A
10 1
11 2
12 3
13 4
14 5
15 6
125
16 7
17 8
18 9
19 10
DV-NC55S/H DV-NC60H
INTERFACE PWB Component Side SIDE A J
I
H
G
F
Wiring Side SIDE A E
D
C
B
A
1
2
3
4
5
6
126
7
8
9
10
DV-NC55S/H DV-NC60H
Component Side SIDE B J
I
H
G
F
Wiring Side SIDE B E
D
C
B
A
1 10
2 11
3 12
4 13
5 14
6 15
127
7 16
8 17
9 18
10 19
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
VCR MAIN PWB Component Side SIDE A J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
128~129
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
Wiring Side SIDE A J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
130~131
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H DV-NC55S/H DV-NC60H
Component Side SIDE B J
Q9913
R9807
Q9906
C7012
R9923
C1210 R9924
IC1203
R7001
IC1205
R1202
R1201
R7002
Q1201
R9910
C1213
R1206 C7002
IC1204
Q9909
C1204
R1204
C1208 Q601
IC1202
IC1201
C7023 C652 R656
RJ1205
R657
C653
Q605
Q652
FB6102 Q681
R682
C520
R617
FB6101 RJ27
R606 R681
R601
R620
C1221
IC1206
C308
C1735
R1723
C1704
R5410
C310
R5412
C1202 C304
C320
R1203
R609
C1207 R610
Q5402
C1706
R5403 C5418
R5408 C306 R301
IC1701
C399
C1712
R1208
R5419
Q5401
C319
C311
C681 R505 C318
R604
C1223 C5411
C1702
C1216 C763
R768 R766
R752
C1713 C315
FB1202
R1210
C1711
R1714
C356
R352
C797
C6314
R603 C317
C1710
C357 R351
RJ33
C6317
R6328
R5352
C214 C210
IC5401 C352
C353
C5356
R5354
C202
R619 C307
C5406
R5401
R5414
R5415
Q5404
IC6301
R6314 R6313
C5402
C5401
R1209
C6305
R6319
C5321
C6309 Q5303
R5413 R6318 R6312
R5314
C1411 R1405 R1404
R6327
C602 C513
R506
R247
C518 C507 C505
C305 C523
R6321 C5316 C5319
R607
R6320
R5357
R6309 C5302
R305 Q5301
R6308
C5311
C5318
R6323
R6322
C5312 Q5302
R5311 C5310
IC5301 C5309
R5409
Q5403
RJ1404
R5310 Q5304
R2104
R5307
R6303
C5303
C5404
R207
R5305 R5304
R5306
R6304
R767
R735
RJ401
C209
C622 R708
C514
C6310 R776
R602 R754
R6325
C6315
Q708
C1409
C5355
R753
C1720 R353 C795
C354
R303
R798
R5301 R5309 C769
C748
R508
IC681
R1720
C309 C509 R210
RJ805
C1812
R1403
IC705
R6305
C628 C316
R312
Q303
Q301
RJ3001
R313
C327
C326
C796
IC5381
C5408
R608 C798
R203 R306
C312
R314
C503
C329
C328
C303
R510
Q302
C794
RJ111
C1715
C302
R502
C506
C330
R5407
C627 C521
C222
R507 Q501
R248
C5412
Q682
C623
C516
RJ5003
R5418
Q603
R625
R605 RJ23 C604
IC201
R504
RJ5002
R5402
Q604
R624
R683
C203 C225
C218
C220 C219
C522
Q201
R209
R1211
C735
C206
R202
RJ21
C207
R618
C205
RJ25
C515
Q502
C581
FB1203
Q9910
R659
RJ806
C625 R612
R611
C5352
C5353
C204
Q5351
R5358
RJ26
Q503
Q582
R726
C1738
R7004
R1205
Q9917
R1207
R7047
C7003
C7004
R731 R728
C626 R613
Q602
Q205
R615
Q581
IC5351
Q5353
Q5352
R785
R725
C732
C736
C747
C775
Q712
RJ50 C729 RJ737
C6308 R5302 R712
Q304
R1810
A4
132~133
R9905 R7006
R756
C781
C780
R769
R719
Q713
C739
C744
R741
C768
C770 R742
R5303 C5306 R723
R1402
B
20 19 18 17 16 15 14 13 12 11 10 9 8 7
R772
R773
R771 R736
RJ2
C756
C758
RJ701
R6310 C5320
C
R763
C765
Q711
IC701
R764
C313 Q703
D
6 5
R616 C5354 R5355
R733
4
R770 R789
R751 R799
R738
3 2 1
C723
Q704
C740 C737
E
R8009
C8009
C722 R778
F
R707
C8008
R5359
C771 R724
G
R801
IC8051
C7016
H
Q9905
Q9908
I
A
R9918 R9917 R9908 RJ7007
R9916
C1219 R7005
C7009
C7091
C7092 R746
R759
R788 R765
RJ37 R730
R1861
RJ721
R614 C5357 R5356 C724
R777
C624 C715 R713 C714 C810 R722
RJ51
R779
C725
RJ10
C817
R201 FB203
RJ11
C730
C776
C731 C760 R760
C502
C743 C757
R745 C755
C754 R750
R743
C749
R749
R501 R509 R315 R802 R732
C5381
R774
R775
R6307
R817
R816
C5304
C5301
C5305 R734
C5315
R5308
C1402 R5312
R1807
R1801
IC1801 R1808
C1407
DV-NC55S/H DV-NC60H
DV-NC55S/H DV-NC60H
Wiring Side SIDE B J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
134~135
12
13
14
15
16
17
18
19
20
DV-NC55S/H DV-NC60H
-MEMO-
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
136
7
8
9
10
DV-NC55S/H DV-NC60H Part No. ★ Description 16. REPLACEMENT PARTS LIST/ Code EXPLODED VIEWS
Ref. No.
Ref. No.
ELECTRICAL PARTS LIST
J J J J
Description
IC702 IC705 IC7701 IC7702
RH-iX3420CEZZ VHiNJM12904-1 VHiBA5984FP-1 VHiTC4W53F/-1
Q201 Q202 Q203 Q205 Q301 Q302 Q303 Q502 Q503 Q701 Q702
VS2SA1576A+-1 VS2SA1576A+-1 VS2SA1576A+-1 VS2SA1576A+-1 VS2SA1576A+-1 VS2SA1298Y/-1 VS2SA1298Y/-1 VS2SA1298Y/-1 VSDTC144EUA-1 VSDTC144EUA-1 VSDTC144EUA-1
D301 D501
VHDDAP222//-1 VHDDAN222//-1
X601
RCRSC0039GEZZ~ J Crystal, CRSC0039GE
FL501
RFiLC0207GEZZ
L601 L602
VP-NM470K2R0N VP-NM470K2R0N
C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C302 C303 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 C324 C325 C326 C328 C332 C501 C502 C503 C504 C506
VCKYCY1CB104K VCEAPF0JW476M VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K RC-EZ0475GEZZ RC-EZ0475GEZZ RC-EZ0475GEZZ VCKYCY0JF105Z VCKYCY0JF105Z VCKYCY1HB103K VCEAPF0JW107M VCEAPF0JW476M VCKYCY1HB103K VCEAPF0JW476M VCEAPF1HW225M VCKYCY1HB103K VCKYCY1HB102K VCKYCY1HB102K VCEAPF0JW476M VCKYCY1HB102K VCKYCY1CB104K VCKYCY1HB102K VCEAPF0JW476M VCKYCY1CB104K VCEAPF0JW476M VCKYCY1HB103K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1HB472K VCKYCY1HB472K VCKYCY1CB104K VCKYCY1HB102K VCKYCY1CB104K VCEAPF0JW107M VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K
Code
IX3420CE, 4M EDO DRAM AT NJM12904 AE BA5984FP, Motor Driver AR TC4W53F AE
TRANSISTORS
Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
" HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER 3. PART NO. 5. PRICE CODE
★
Part No.
2. REF. NO. 4. DESCRIPTION
J J J J J J J J J J J
2SA1576A+ 2SA1576A+ 2SA1576A+ 2SA1576A+ 2SA1576A+ 2SA1298Y 2SA1298Y 2SA1298Y DTC144EUA DTC144EUA DTC144EUA
AB AB AB AB AB AB AB AB AB AB AB
DIODES å MARK: SAFETY RELATED PARTS
J DAP222 J DAN222
AA AA
PWB ASSEMBLY IS NOT REPLACEMENT ITEM
PACKAGED CIRCUIT ★ MARK: SPARE PARTS DELIVERY SECTION
AH
FILTER Ref. No.
Part No.
★
Description
Code
(NOT REPLACEMENT ITEM)
DUNTKB086TEV1 DUNTKB041TEV1 DUNTKB085TEV1 DUNTKB045TEV1 DUNTKB046TEV1 DUNTKB047TEV1 DUNTKB087TEV1 DUNTKB040TEV1 DUNTKB084TEV1 DUNTKB043TEV1 DUNTKB043TEV2
– DVD Main PWB Unit – VCR Display PWB Unit (DV-NC55S/H) – VCR Display PWB Unit (DV-NC60H) – DVD Display PWB Unit (DV-NC55S/H) – DVD Display PWB Unit (DV-NC60H) – AV PWB Unit – Terminal PWB Unit – Power PWB Unit (DV-NC55S/H) – Power PWB Unit (DV-NC60H) – Interface PWB Unit (DV-NC55S/H) – Interface PWB Unit (DV-NC60H) – VCR Main PWB Unit (DV-NC55H/60H) – VCR Main PWB Unit (DV-NC55S)
— — — — — — — — — — — — —
INTEGRATED CIRCUITS VHiTA1323F+-1Q RH-iX1689GEZZ RH-iX1765GEZZ
IC503 IC504 IC507 IC508 IC601 IC602 IC603 IC701
VHiPST600iM-1 RH-iX1687GEZZ VHiBR93L66F-1 RH-iX1761GEZZQ RH-iX1720GEZZQ RH-iX0751TAZZ RH-iX0751TAZZ VHiTC94A03F-1Q
J TA1323F+, RF Processor J IX1689GE, Flash ROM 8M J IX1765GE, Work RAM 4M EDO J PST600iM, Reset J IX1687GE, Micro Com. J BR93L66F, E2PROM J IX1761GE J IX1720GE, AV Decoder J IX0751TA, 16M SDRAM J IX0751TA, 16M SDRAM J TC94A03F, Servo ECC
J Peaking, 47µH J Peaking, 47µH
AB AB
CAPACITORS
DUNTK6054TE6E DVD MAIN PWB UNIT IC301 IC501 IC502
AD
COILS
PRINTED WIRING BOARD ASSEMBLIES DUNTK6054TE6E DUNTKB042TEV1
J Filter, FiLC0207GE
AV BB AX AE BD AH AW BG AX AX BC
137
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
0.1 47 0.01 0.01 0.01 0.01 0.01 0.01 220 220 220 1 1 0.01 100 47 0.01 47 2.2 0.01 1000p 1000p 47 1000p 0.1 1000p 47 0.1 47 0.01 0.1 0.1 4700p 4700p 0.1 1000p 0.1 100 0.1 0.1 0.1
16V 6.3V 50V 50V 50V 50V 50V 50V 6.3V 6.3V 6.3V 6.3V 6.3V 50V 6.3V 6.3V 50V 6.3V 50V 50V 50V 50V 6.3V 50V 16V 50V 6.3V 16V 6.3V 50V 16V 16V 50V 50V 16V 50V 16V 6.3V 16V 16V 16V
Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic
AB AB AA AA AA AA AA AA AD AD AD AB AB AA AC AB AA AB AB AA AA AA AB AA AB AA AB AB AB AA AB AB AA AA AB AA AB AC AB AB AB
DV-NC55S/H DV-NC60H Ref. No.
Part No.
★
Description
Ref. No.
Code
DUNTK6054TE6E DVD MAIN PWB UNIT(Continued) C508 C510 C511 C512 C515 C516 C517 C519 C520 C521 C522 C523 C524 C525 C526 C527 C528 C529 C602 C603 C604 C605 C606 C609 C610 C613 C614 C617 C618 C619 C620 C621 C623 C624 C625 C626 C627 C628 C629 C630 C631 C632 C633 C635 C640 C641 C643 C644 C646 C701 C702 C703 C704 C705 C706 C707 C708 C709 C710 C711 C712 C713 C714 C715 C716 C717 C718 C720 C721 C722 C723 C725
VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY0JF105Z VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCEAPF0JW476M VCKYCY1HB103K VCKYCY1HB472K VCKYCY1HB103K VCEAPF0JW476M VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1CB104K RC-EZ0475GEZZ VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K RC-EZ0475GEZZ VCKYCY1CB104K VCKYCY1CB104K RC-EZ0475GEZZ VCKYCY1CB104K VCKYCY1CB104K VCEAPF0JW476M VCKYCY1CB104K VCCCCY1HH100D VCCCCY1HH100D VCEAPF0JW476M RC-EZ0475GEZZ VCKYCY1CB104K VCEAPF0JW476M VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCEAPF0JW107M VCKYCY1HB103K VCCCCY1HH820J VCCCCY1HH820J VCKYCY1HB103K VCCCCY1HH221J VCCCCY1HH221J VCEAPF0JW476M VCKYCY1CB104K VCCCCY1HH221J VCEAPF1CW106M VCKYCY1CB104K VCKYCY1CB104K VCKYCY1HB103K VCEAPF0JW476M VCKYCY1CB104K VCCCCY1HH221J VCKYCY1HB472K VCKYCY1HB153K VCKYCY1HB682K VCKYCY1HB153K VCKYCY1HB153K VCKYCY1CB104K VCKYCY1CB104K
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
0.1 0.1 0.1 1 0.01 0.01 0.01 0.01 0.01 0.01 47 0.01 4700p 0.01 47 0.01 0.01 0.01 0.1 220 0.1 0.1 0.1 0.1 0.1 0.1 0.1 220 0.1 0.1 220 0.1 0.1 47 0.1 10p 10p 47 220 0.1 47 0.1 0.1 0.1 0.1 0.1 0.1 0.1 100 0.01 82p 82p 0.01 220p 220p 47 0.1 220p 10 0.1 0.1 0.01 47 0.1 220p 4700p 0.015 6800p 0.015 0.015 0.1 0.1
16V 16V 16V 6.3V 50V 50V 50V 50V 50V 50V 6.3V 50V 50V 50V 6.3V 50V 50V 50V 16V 6.3V 16V 16V 16V 16V 16V 16V 16V 6.3V 16V 16V 6.3V 16V 16V 6.3V 16V 50V 50V 6.3V 6.3V 16V 6.3V 16V 16V 16V 16V 16V 16V 16V 6.3V 50V 50V 50V 50V 50V 50V 6.3V 16V 50V 16V 16V 16V 50V 6.3V 16V 50V 50V 50V 50V 50V 50V 16V 16V
Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic
AB AB AB AB AA AA AA AA AA AA AB AA AA AA AB AA AA AA AB AD AB AB AB AB AB AB AB AD AB AB AD AB AB AB AB AA AA AB AD AB AB AB AB AB AB AB AB AB AC AA AA AA AA AA AA AB AB AA AB AB AB AA AB AB AA AA AA AA AA AA AB AB
★
Part No.
C726 C727 C728 C729 C730 C731 C732 C733 C734 C735 C741 C742 C744 C746 C747 C748 C749 C750 C751 C752 C753 C756 C757 C758 C759 C7702 C7703 C7704 C7705 C7706 FL701
VCKYCY1CB104K J VCKYCY1CB104K J VCCCCY1HH221J J VCKYCY1HB472K J VCKYCY1CB104K J VCKYCY1HB102K J VCKYCY1CB104K J VCKYCY1CB104K J VCCCCY1HH561J J VCKYCY1HB103K J VCKYCY1HB103K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1HB103K J VCKYCY1HB103K J VCKYCY1CB104K J VCKYCY1HB102K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1CB104K J VCKYCY1HB103K J VCEAPF1CW106M J VCCCCY1HH101J J VCCCCY1HH221J J VCKYCY1CB104K J RCRMC0001GEZZ~J
R224 R225 R226 R227 R303 R310 R311 R314 R315 R316 R317 R318 R319 R320 R325 R326 R327 R328 R343 R344 R345 R501 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 R513 R514 R515 R516 R517 R518 R519 R520 R522 R523
VRS-CY1JF681J VRS-CY1JF681J VRS-CY1JF681J VRS-CY1JF681J VRS-CY1JF222J VRS-CY1JF472J VRS-CY1JF335J VRS-TW2ED330J VRS-CY1JF471J VRS-CY1JF335J VRS-CY1JF103J VRS-TW2ED470J VRS-TW2ED470J VRS-CY1JF471J VRS-CY1JF820J VRS-CY1JF100J VRS-CY1JF820J VRS-CY1JF100J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF332J VRS-CY1JF332J VRS-CY1JF332J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF154J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF100J VRS-CY1JF473J
Description 0.1 16V Ceramic 0.1 16V Ceramic 220p 50V Ceramic 4700p 50V Ceramic 0.1 16V Ceramic 1000p 50V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 560p 50V Ceramic 0.01 50V Ceramic 0.01 50V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.01 50V Ceramic 0.01 50V Ceramic 0.1 16V Ceramic 1000p 50V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.1 16V Ceramic 0.01 50V Ceramic 10 16V Electrolytic 100p 50V Ceramic 220p 50V Ceramic 0.1 16V Ceramic Ceramic Vibrator
Code AB AB AA AA AB AA AB AB AB AA AA AB AB AB AB AA AA AB AA AB AB AB AB AB AB AA AB AA AA AB AD
RESISTORS
138
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
680 680 680 680 2.2k 4.7k 3.3M 33 470 3.3M 10k 47 47 470 82 10 82 10 0 0 0 1k 10k 10k 10k 3.3k 3.3k 3.3k 10 10 10 10k 4.7k 1k 150k 10k 1k 1k 1k 10k 10 47k
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/16W 1/16W 1/16W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
DV-NC55S/H DV-NC60H Ref. No.
Part No.
★
Description
Code
Ref. No.
DUNTK6054TE6E DVD MAIN PWB UNIT(Continued) R524 R525 R528 R529 R530 R531 R532 R533 R534 R535 R536 R537 R538 R540 R541 R543 R544 R545 R552 R555 R556 R557 R558 R560 R561 R564 R565 R566 R568 R569 R570 R571 R601 R602 R603 R604 R607 R608 R610 R612 R613 R615 R616 R617 R620 R621 R622 R701 R702 R703 R704 R705 R706 R707 R708 R709 R710 R711 R712 R713 R714 R715 R716 R717 R718 R719 R720 R721 R724 R725 R726 R727
VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF222J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF562J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF100J VRS-CY1JF103J VRS-CY1JF560F VRS-CY1JF391F VRS-CY1JF560F VRS-CY1JF560F VRS-CY1JF560F VRS-CY1JF684J VRS-CY1JF101J VRS-CY1JF221J VRS-CY1JF391J VRS-CY1JF221J VRS-CY1JF221J VRS-CY1JF221J VRS-CY1JF180J VRS-CY1JF223J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF223J VRS-CY1JF682J VRS-CY1JF222J VRS-CY1JF000J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF822J VRS-CY1JF000J VRS-CY1JF473J VRS-CY1JF154J VRS-CY1JF181J VRS-CY1JF183J VRS-CY1JF151J VRS-CY1JF151J VRS-CY1JF151J VRS-CY1JF222J VRS-CY1JF104J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF331J
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
10k 10k 10k 4.7k 10k 4.7k 10k 10k 10k 10k 0 10k 10k 4.7k 1k 10k 4.7k 1k 0 0 1k 2.2k 4.7k 10k 10k 5.6k 10k 10k 100 100 0 0 10 10k 56 390 56 56 56 680k 100 220 390 220 220 220 18 22k 10k 10k 22k 6.8k 2.2k 0 12k 12k 12k 12k 8.2k 0 47k 150k 180 18k 150 150 150 2.2k 100k 1k 0 330
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
★
Part No.
R728 R729 R730 R731 R732 R734 R735 R736 R737 R738 R739 R740 R741 R742 R743 R744 R745 R746 R747 R748 R749 R750 R751 R752 R753 R754 R755 R756 R757 R758 R759 R760 R761 R762 R763 R764 R765 R768 R769 R780 R820 R821 R822 R823 R824 R825 R827 R7717 R7721 R7722 R7724 R7725 R7726 R7729 R7730 R7732 R7734 R7736
VRS-CY1JF331J VRS-CY1JF393J VRS-CY1JF273J VRS-CY1JF273J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF333F VRS-CY1JF472J VRS-CY1JF473F VRS-CY1JF000J VRS-CY1JF333F VRS-CY1JF152J VRS-CY1JF473F VRS-CY1JF103J VRS-CY1JF104J VRS-CY1JF000J VRS-CY1JF333J VRS-CY1JF000J VRS-CY1JF154J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF334J VRS-CY1JF105J VRS-CY1JF471J VRS-CY1JF100J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF472J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF100J VRS-CY1JF102J VRS-CY1JF223J VRS-CY1JF223J VRS-CY1JF333J VRS-CY1JF223J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF473J VRS-CY1JF102J VRS-CY1JF822J VRS-CY1JF102J
FB301 FB601 FB602 FB603 FB605 FB806 FB807 FB808 FB809 FB810 FB813 FB814 FB815 FB816 FB817
RBLN-0077TAZZ RBLN-0061TAZZ RBLN-0052TAZZ RBLN-0061TAZZ RBLN-0061TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0076TAZZ RBLN-0077TAZZ
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
Description 330 39k 27k 27k 10k 10k 10k 10k 0 33k 4.7k 47k 0 33k 1.5k 47k 10k 100k 0 33k 0 150k 0 0 330k 1M 470 10 10k 10k 1k 1k 0 0 0 0 0 0 0 0 4.7k 10 10 10 10k 100 10 1k 22k 22k 33k 22k 10k 10k 47k 1k 8.2k 1k
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide
Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
BALUNES
139
J J J J J J J J J J J J J J J
Balun, BLN-0077TA Balun, BLN-0061TA Balun, BLN-0052TA Balun, BLN-0061TA Balun, BLN-0061TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0076TA Balun, BLN-0077TA
AB AD AC AD AD AB AB AB AB AB AB AB AB AC AB
DV-NC55S/H DV-NC60H Ref. No.
★
Part No.
Description
Ref. No.
Code
DUNTK6054TE6E DVD MAIN PWB UNIT(Continued) R801 R802 R803 R804 R805 R806 R812 R813 R814 R815 R816 R817 R818 R819
RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ
J J J J J J J J J J J J J J
CN201 CN301 CN302 CN701 CN702 CN703 CN801 CN802 CN803
QPLGN0964TAZZ J QSOCN2336TAZZ~ J QPLGN0464TAZZ J QPLGN0664TAZZ J QPLGN0564TAZZ J QPLGN0364TAZZ J QSOCN2936TAZZ J QSOCN0936TAZZ J QPLGN0264TAZZ J
Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA Balun, BLN-0076TA
AC AC AC AC AC AC AC AC AC AC AC AC AC AC
R5116
VRD-RA2BE822J
R5116
VRS-CY1JF822J
R5117 R5118 R5119
VRS-CY1JF103J VRS-CY1JF223J VRS-CY1JF563J
J KRC102S J KRC102S
IC5001 VHiPT6312LQ-1
VP-XF100J0000 VP-XF100J0000
AU
C5101 C5102 C5103 C5104 C5115 C5116
VCEA9M1CW106M VCKYCY1HF103Z VCKYCY1HF103Z VCEA0A0JW477M VCCCCY1HH101J VCCCCY1HH101J
J Peaking, 10µH J Peaking, 10µH
10 0.01 0.01 470 100p 100p
16V 50V 50V 6.3V 50V 50V
Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic
VRS-CY1JF750J VRS-CY1JF332J VRS-CY1JF272J VRS-CY1JF472J VRD-RA2BE101J VRS-CY1JF332J VRD-RA2BE472J VRS-CY1JF822J VRD-RA2BE103J
J J J J J J J J J
R5110
VRS-CY1JF103J
J
R5111 R5112 R5114 R5115
VRS-CY1JF223J VRD-RA2BE563J VRD-RA2BE272J VRD-RA2EE2R7J
J J J J
75 1/16W 3.3k 1/16W 2.7k 1/16W 4.7k 1/16W 100 1/8W 3.3k 1/16W 4.7k 1/8W 8.2k 1/16W 10k 1/8W (NC55S/H) 10k 1/16W (NC60H) 22k 1/16W 56k 1/8W 2.7k 1/8W 2.7 1/4W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Carbon Metal Oxide Carbon
AB AA AA AC AA AA
AB AB AB AB AB AB AB
J J J J J J J
Socket, 11Pin Socket, 11Pin Socket, 15Pin Jack, VIDEO IN Jack, AUDIO IN(L) Jack, AUDIO IN(R) Remote Receiver
AC AD AD AE AE AE AF
J PT6312LQ, FL Driver
AM
VSKRC102S//-1 VSKRC102S//-1 VSKRC102S//-1 VSKRC102S//-1 VSKRC102S//-1
J J J J J
KRC102S KRC102S KRC102S KRC102S KRC102S
AA AA AA AA AA
AS AC AD AB AA AD
CAPACITORS
AA AA AA AA AB AA AA AA AA
C5005 C5006 C5007 C5008 C5009 C5010 C5011
VCKYCY1HF103Z VCEA9M1CW106M VCKYCY1HF103Z VCCCCY1HH330J VCCCCY1HH330J VCCCCY1HH330J VCKYCY1HF103Z
R5001 R5002
VRD-RA2BE102J VRD-RA2BE181J
R5003 R5010 R5011 R5012 R5013
VRS-CY1JF561J VRS-CY1JF104J VRD-RA2BE103J VRD-RA2BE103J VRD-RA2BE103J
J J J J J J J
0.01 10 0.01 33p 33p 33p 0.01
50V 16V 50V 50V 50V 50V 50V
Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic
AA AB AA AA AA AA AA
Carbon Carbon
AA AA
Metal Oxide Metal Oxide Carbon Carbon Carbon
AA AA AA AA AA
RESISTORS
Metal Oxide AA Metal Oxide Carbon Carbon Carbon
Switch, POWER Switch, EJECT/STOP Switch, CH– Switch, CH+ Switch, PLAY Switch, REC(NC60H) Switch, REW
DG5001 VVK06SS72T+-1 J Display D5001 RH-PX0432GEZZ+ J PhotoDiode, DUB LED D5002 VHPSEL1913K-1+ J PhotoDiode, DVD LED (NC55S/H) D5003 VHD1SS119//-1 J 1SS119 D5004 RH-EX0601GEZZ J Zener, EX0601GE D5005 VHPSEL4914D-1+ J PhotoDiode, DVD LED (NC60H)
RESISTORS R5102 R5103 R5104 R5105 R5106 R5107 R5108 R5109 R5110
J J J J J J J
DIODES AND LED’S
AB AB
CAPACITORS J J J J J J
AC
TRANSISTORS Q5003 Q5004 Q5005 Q5006 Q5007
COILS L5101 L5102
J Balun, BLN-0076TA
INTEGRATED CIRCUIT
AM
AA AA
J Display
Metal Oxide AA Metal Oxide AA Metal Oxide AA
DUNTKB041TEV1(DV-NC55S/H) DUNTKB085TEV1(DV-NC60H) DVD DISPLAY PWB UNIT
LED DG5101 VVK20U106SB-1
Metal Oxide AA
MISCELLANEOUS PARTS
TRANSISTORS VSKRC102S//-1 VSKRC102S//-1
QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ
CN5101 QSOCN1195REZZ CN5102 QSOCN1199REZZ CN5103 QSOCN1595REZZ J5101 QJAKE0190CEZZ J5102 QJAKE0257GEZZ J5103 QJAKE0180CEZZ RMC5101 RRMCU0233CEZZ
INTEGRATED CIRCUIT
Q5101 Q5102
AA
SWITCHES S5101 S5102 S5103 S5104 S5106 S5107 S5108
AF AF AC AD AC AC AF AD AC
J MN12512+, Fip Driver
Carbon
Code
BALUN
DUNTKB042TEV1(DV-NC55S/H) DUNTKB086TEV1(DV-NC60H) VCR DISPLAY PWB UNIT IC5101 VHiMN12512+-1
Description
J 8.2k 1/8W (NC60H) J 8.2k 1/16W (NC55S/H) J 10k 1/16W J 22k 1/16W J 56k 1/16W
FB5101 RBLN-0076TAZZ
MISCELLANEOUS PARTS Plug, 9Pin Socket, 23Pin Plug, 4Pin Plug, 6Pin Plug, 5Pin Plug, 3Pin Socket, 29Pin Socket, 9Pin Plug, 2Pin
★
Part No.
AA AA AA AA
140
J 1k 1/8W J 180 1/8W (NC55S/H) J 560 1/16W J 100k 1/16W J 10k 1/8W J 10k 1/8W J 10k 1/8W
DV-NC55S/H DV-NC60H Ref. No.
★
Part No.
Description
Code
DUNTKB041TEV1(DV-NC55S/H) DUNTKB085TEV1(DV-NC60H) DVD DISPLAY PWB UNIT R5014 R5015 R5016 R5017 R5018 R5019
VRS-CY1JF333J VRS-CY1JF183J VRD-RM2HD2R7J VRS-CY1JF332J VRS-CY1JF332J VRD-RA2BE181J
S5001 S5002 S5003
QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ
J J J J J J
33k 1/16W 18k 1/16W 2.7 1/2W 3.3k 1/16W 3.3k 1/16W 180 1/8W (NC60H)
Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Carbon
AA AA AA AA AA AA
SWITCHES J Switch, OPEN/CLOSE J Switch, PLAY J Switch, STOP
AB AB AB
MISCELLANEOUS PARTS CN5001 QSOCN2399REZZ J Socket, 23Pin CN5002 QSOCN1199REZZ J Socket, 11Pin
Part No.
★
C2009 C2010 C2011 C2012 C2014 C2015 C2016 C2017 C2018 C2019 C2516 C2517 C6052 C6053 C6054 C6055 C6056 C6057 C6058 C6059 C6152 C6153 C6154 C6155 C6156 C6157
VCEA9M0JW107M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW106M VCEA9M0JW476M VCKYCY1EB103K VCEA9M1CW106M VCEA9M1CW106M VCKYCY1CF104Z VCKYCY1CF104Z VCEA9A1CW106M VCEA9A1CW106M VCEA9M1CW476M VCEA9M0JW107M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW106M VCEA9A1CW476M VCEA9M0JW107M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW106M
J J J J J J J J J J J J J J J J J J J J J J J J J J
R2001 R2002 R2003 R2004 R2005 R2006 R2007 R2008 R2009 R2010 R2011 R2012 R2013 R2014 R2015 R2326 R2339 R2340 R2341 R2342 R6060 R6061 R6062 R6063 R6064 R6065 R6066 R6067 R6068 R6069 R6070 R6071 R6072 R6073 R6074 R6075 R6076 R6160 R6161 R6162 R6163 R6164 R6165 R6166 R6167 R6168 R6175
VRS-CY1JF272J VRS-CY1JF332J VRS-CY1JF272J VRS-CY1JF272J VRS-CY1JF332J VRS-CY1JF272J VRS-CY1JF272J VRS-CY1JF332J VRS-CY1JF272J VRS-CY1JF272J VRS-CY1JF332J VRS-CY1JF272J VRS-CY1JF272J VRS-CY1JF102J VRD-RA2BE103J VRS-CY1JF332J VRS-CY1JF332J VRS-CY1JF562J VRS-CY1JF102J VRD-RA2EE750J VRS-CY1JF561J VRS-CY1JF561J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF153J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF821J VRS-CY1JF821J VRS-CY1JF272J VRS-CY1JF272J VRS-CY1JF393J VRS-CY1JF393J VRS-CY1JF561J VRS-CY1JF561J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF823J VRS-CY1JF823J VRD-RA2BE153J VRS-CY1JF000J
Ref. No.
AE AD
DUNTKB045TEV1 AV PWB UNIT INTEGRATED CIRCUITS IC2001 VHiMM1540AF-1 IC2002 VHiMM1113XF1E IC2003 VHiMM1111XF1E IC2004 VHiMM1111XF1E IC6010 VHiBU4053V/-1 IC6011 VHiNJM4565M-1~ IC6110 VHiBU4053V/-1
J MM1540AF, Driver J MM1113XF, Y/COMP. Selector J MM1111XF, DUB Video Selector J MM1111XF, VCR/DVD Selector J BU4053V, Audio Selector J NJM4565M, BUFF J BU4053V, DVD Audio Selector
VS2PB709AR/-1 VS2PB709AR/-1 VS2PB709AR/-1 VS2PB709AR/-1 VSUN2213///-1 VSUN2213///-1 VSUN2213///-1 VSUN2213///-1 VSUN2213///-1 VSUN2111///-1 VSUN2213///-1 VSUN2213///-1 VS2PD601AR/-1 VS2PD601AR/-1 VSUN2213///-1 VSUN2213///-1 VS2SD1306-E1E VS2SD1306-E1E VSUN2213///-1
J J J J J J J J J J J J J J J J J J J
D2301 D2302 D2307
VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1
C2001 C2002 C2003 C2004 C2005 C2006 C2007 C2008
VCEA9M1CW107M VCKYCY1EB103K VCKYCY1CF104Z VCEA9M1HW105M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1HW105M VCEA9M1HW105M
2PB709AR 2PB709AR 2PB709AR 2PB709AR UN2213 UN2213 UN2213 UN2213 UN2213 UN2111 UN2213 UN2213 2PD601AR 2PD601AR UN2213 UN2213 2SD1306-E 2SD1306-E UN2213
AE AE AE AD AE
AB AB AB AB AA AA AA AA AA AA AA AA AB AB AA AA AD AD AA
DIODES J 1SS119 J 1SS119 J 1SS119
AB AB AB
CAPACITORS J J J J J J J J
100 0.01 0.1 1 10 10 1 1
16V 25V 16V 50V 16V 16V 50V 50V
Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic
100 10 10 10 47 0.01 10 10 0.1 0.1 10 10 47 100 10 10 10 10 10 10 47 100 10 10 10 10
6.3V 16V 16V 16V 6.3V 25V 16V 16V 16V 16V 16V 16V 16V 6.3V 16V 16V 16V 16V 16V 16V 16V 6.3V 16V 16V 16V 16V
Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic
Code AB AB AB AB AB AA AB AB AA AA AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB
RESISTORS
AN AE
TRANSISTORS Q2001 Q2002 Q2003 Q2004 Q2005 Q2006 Q2007 Q2014 Q2309 Q2310 Q2311 Q2313 Q2315 Q2316 Q2317 Q6010 Q6011 Q6012 Q6110
Description
AB AA AA AB AB AB AB AB
141
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
2.7k 3.3k 2.7k 2.7k 3.3k 2.7k 2.7k 3.3k 2.7k 2.7k 3.3k 2.7k 2.7k 1k 10k 3.3k 3.3k 5.6k 1k 75 560 560 82k 82k 82k 82k 82k 82k 15k 100k 100k 820 820 2.7k 2.7k 39k 39k 560 560 82k 82k 82k 82k 82k 82k 15k 0
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
DV-NC55S/H DV-NC60H Ref. No.
★
Part No.
Description
DUNTKB045TEV1 AV PWB UNIT(Continued) R6176
VRS-CY1JF000J
J 0
1/16W Metal Oxide AA
BALUN FB2001 RBLN-0076TAZZ
J Balun, BLN-0076TA
AC
MISCELLANEOUS PARTS SC2001 SC2002 SC2003 SC2004 SC2005 SC2006 SC2007 SC2008 SC2009
QSOCN1995REZZ QSOCN1995REZZ QSOCN0999REZZ QPLGN0278GEZZ QSOCN0995REZZ QSOCN1279GEZZ QSOCN1279GEZZ QSOCN0779GEZZ QSOCN1279GEZZ
J J J J J J J J J
Socket, 19Pin Socket, 19Pin Socket, 9Pin Plug, 2Pin Socket, 9Pin Socket, 12Pin Socket, 12Pin Socket, 7Pin Socket, 12Pin
AD AD AD AA AC AC AC AC AC
DUNTKB046TEV1 TERMINAL PWB UNIT INTEGRATED CIRCUITS IC2501 VHiLA73024V-1~ J LA73024V, Selector IC2502 VHiMM1114XF1E~ U MM1114XF, R/CHROMA Selector IC2503 VHiMM1506XN-1 J MM1506XN, G Selector IC2504 VHiMM1506XN-1 J MM1506XN, B Selector IC2505 VHiTC4W53F/-1 J TC4W53F, Selector
AN AH AE AE AE
TRANSISTORS Q2503 Q2504 Q2505 Q2506 Q2507 Q2508 Q2901 Q2902
VSUN2213///-1 VS2PD601AR/-1 VS2PD601AR/-1 VS2PD601AR/-1 VS2PD601AR/-1 VSUN2213///-1 VS2PB709AR/-1 VSUN2113///-1
J J J J J J J J
D2502 D2503 D2505 D2506 D2507 D2508 D2509 D2510 D2511 D2512 D2513 D2514 D2516 D2517 D2518 D2519 D2520 D2521 D2522 D2526 D2527 D2528
RH-EX0627GEZZ RH-EX0627GEZZ RH-EX0646GEZZ RH-EX0627GEZZ RH-EX0646GEZZ RH-EX0646GEZZ RH-EX0646GEZZ RH-EX0646GEZZ RH-EX0646GEZZ RH-EX0646GEZZ RH-EX0627GEZZ RH-EX0627GEZZ RH-EX0627GEZZ RH-EX0646GEZZ RH-EX0646GEZZ RH-EX0646GEZZ RH-EX0646GEZZ RH-EX0627GEZZ RH-EX0627GEZZ RH-EX0627GEZZ RH-EX0627GEZZ RH-EX0646GEZZ
C2501 C2502 C2503 C2504 C2505 C2506 C2507
VCEA9M1CW106M VCEA9M1CW106M VCEA9M1HW105M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1HW105M VCEA9M1CW106M
UN2213 2PD601AR 2PD601AR 2PD601AR 2PD601AR UN2213 2PB709AR UN2213
AA AB AB AB AB AA AB AA
Zener, EX0627GE Zener, EX0627GE Zener, EX0646GE Zener, EX0627GE Zener, EX0646GE Zener, EX0646GE Zener, EX0646GE Zener, EX0646GE Zener, EX0646GE Zener, EX0646GE Zener, EX0627GE Zener, EX0627GE Zener, EX0627GE Zener, EX0646GE Zener, EX0646GE Zener, EX0646GE Zener, EX0646GE Zener, EX0627GE Zener, EX0627GE Zener, EX0627GE Zener, EX0627GE Zener, EX0646GE
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
CAPACITORS J J J J J J J
10 10 1 10 10 1 10
16V 16V 50V 16V 16V 50V 16V
Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic
★
C2508 C2509 C2510 C2511 C2512 C2513 C2514 C2515 C2518 C2519 C2520 C2521 C2522 C2530 C2531 C2532 C2533 C2534 C2535 C2536 C2538 C2539 C2540 C2541 C2542 C2543 C2544 C2545 C2546 C2547 C2560 C2561 C2562 C2563 C2564 C2565 C2566
VCEA9M1CW106M VCEA9M1HW105M VCEA9M1HW105M VCEA9M1HW105M VCEA9M1CW107M VCKYCY1EF104Z VCKYCY1EF104Z VCEA0M0JW477M VCEA9M1CW106M VCEA9M1CW106M VCKYCY1HF103Z VCKYCY1EF104Z VCKYCY1HF103Z VCKYCY1EF104Z VCEA9M0JW227M VCE9EM1AW106M VCEA9M1CW106M VCKYCY1EF104Z VCE9EM1AW106M VCEA9M1CW106M VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW107M VCKYCY1HF103Z VCEA9M0JW476M VCEA9M1CW106M VCKYCY1EF104Z
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
JP2501 JP2502 R2236 R2238 R2242 R2501 R2502 R2503 R2504 R2505 R2506 R2507 R2508 R2509 R2510 R2511 R2512 R2513 R2514 R2515 R2522 R2523 R2524 R2525 R2544 R2545 R2546 R2547 R2551 R2552 R2553 R2554 R2556 R2557 R2558 R2559
VRD-RA2BER0RJ VRD-RA2BER0RJ VRS-CY1JF103J VRS-CY1JF103J VRD-RA2BE102J VRS-CY1JF123J VRS-CY1JF123J VRD-RA2BE750J VRD-RA2BE750J VRD-RA2BE821J VRD-RA2BE821J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF821J VRS-CY1JF821J VRD-RA2BE750J VRD-RA2BE750J VRD-RA2BE750J VRD-RA2BE750J VRD-RA2BE750J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF101J VRS-CY1JF470J VRS-CY1JF681J VRD-RA2BE750J VRS-CY1JF101J VRS-CY1JF470J VRS-CY1JF681J VRD-RA2BE750J VRS-CY1JF102J VRS-CY1JF272J VRS-CY1JF101J VRS-CY1JF822J
Description 10 1 1 1 100 0.1 0.1 470 10 10 0.01 0.1 0.01 0.1 220 10 10 0.1 10 10 100p 100p 100p 100p 100p 100p 100p 100p 100p 100p 10 10 100 0.01 47 10 0.1
16V 50V 50V 50V 16V 25V 25V 6.3V 16V 16V 50V 25V 50V 25V 6.3V 10V 16V 25V 10V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 50V 6.3V 16V 25V
Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Ceramic
Code AB AB AB AB AB AA AA AC AB AB AA AA AA AA AB AB AB AA AB AB AA AA AA AA AA AA AA AA AA AA AB AB AB AA AB AB AA
RESISTORS
DIODES J J J J J J J J J J J J J J J J J J J J J J
Part No.
Ref. No.
Code
AB AB AB AB AB AB AB
142
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
0.0R 0.0R 10k 10k 1k 12k 12k 75 75 820 820 12k 12k 820 820 75 75 75 75 75 12k 12k 12k 12k 100 47 680 75 100 47 680 75 1k 2.7k 100 8.2k
1/8W 1/8W 1/16W 1/16W 1/8W 1/16W 1/16W 1/8W 1/8W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/8W 1/8W 1/8W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W
Carbon Carbon Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Carbon Carbon Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Carbon Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
DV-NC55S/H DV-NC60H Ref. No.
★
Part No.
Description
Code
DUNTKB046TEV1 TERMINAL PWB UNIT(Continued) R2560 R2561 R2562 R2563 R2564 R2565 R2566 R2901 R2903 R2904 R2907 R2909
VRS-CY1JF183J VRS-CY1JF470J VRS-CY1JF102J VRS-CY1JF470J VRS-CY1JF681J VRD-RA2BE750J VRS-CY1JF153J VRD-RA2EE331J VRS-CY1JF183J VRS-CY1JF153J VRS-CY1JF821J VRS-CY1JF472J
J J J J J J J J J J J J
S2501
QSW-S0270GEZZ
FB2501 FB2502 FB2505 FB2506 FB2507 FB2508 FB2509 FB2510 FB2511 FB2512 FB2513 FB2514
RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0076TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0076TAZZ
18k 47 1k 47 680 75 15k 330 18k 15k 820 4.7k
1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/4W 1/16W 1/16W 1/16W 1/16W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA
SWITCH J Switch
AF
BALUNES J J J J J J J J J J J J
Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0076TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0076TA
AB AB AB AB AB AC AB AB AB AB AB AC
Ref. No.
Part No.
★
Description
J J J J J J J J J J J J J J J J J J J J J J J J
DX0220CE DX0220CE DX0220CE DX0220CE Zener, EX0611GE 1SS119 Zener, EX0610GE Zener, EX0611GE 1SS119 1SS119 1SS119 1SS119 1SS119 1F4G 1SS244 DX0436CE 15DF1FC 15DF1FC 1SS244 1SS119 1SS119 1SS119 FX0001AJ FX0001AJ
å å å å
D910 D911 D912 D913 D9051 D9052 D9053 D9054 D9091 D9092 D9093 D9094 D9095 D9601 D9602 D9603 D9604 D9605 D9606 D9611 D9612 D9613 å IC901 å IC902
RH-DX0220CEZZ RH-DX0220CEZZ RH-DX0220CEZZ RH-DX0220CEZZ RH-EX0611GEZZ VHD1SS119//-1 RH-EX0610GEZZ RH-EX0611GEZZ VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1F4G////-1 VHD1SS244//-1 RH-DX0436CEZZ VHD15DF1FC/1E VHD15DF1FC/1E VHD1SS244//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-FX0001AJZZ RH-FX0001AJZZ
å L901 L9601 L9602 L9603 å T901
RCiLF0275GEZZ RCiLP0171CEZZ RCiLP0171CEZZ RCiLP0171CEZZ RTRNWA005WJZZ
å å å å å å å å å
C901 C902 C903 C904 C905 C908 C909 C910 C913 C9021 C9052 C9053 C9055 C9057 C9058 C9059 C9060 C9061 C9063 C9064 C9072 C9601 C9603 C9605 C9606 C9608 C9609 C9610 C9611 C9612 C9613 C9614 C9616 C9618
RC-FZ029CUMZZ J RC-FZ029CUMZZ J RC-KZ0105GEZZ J RC-EZ0437GEZZ J RC-KZ0112CEZZ J VCQYTA1HM152J J VCEA0M1HW336M+J VCQYTA1HM332J J RC-EZ0661GEZZ J VCEA9M0JW107M J VCEA0M1AW477M+J VCEA9M1CW476M J VCEA9M1CW476M J VCEA9M0JW107M J VCEA9M0JW107M J VCEA0A1CW108M J VCEA9M1CW106M J VCEA9M1CW106M J VCEA9M1HW225M J VCEA9M1HW225M J VCEA0A1CW227M J VCEA0M1AW477M+J VCEA0M1JW476M+ J VCEA0A1VW477M J VCEA0M1VW476M+J RC-EZ1087CEZZ J VCEA0M1EW107M+J RC-EZ1075CEZZ J VCEA0M1AW477M+J VCEA0M1HW476M+J VCEA9M1HW105M J VCKYCY1EF104Z J VCKYD41CY103N J VCEA9M1HW105M J
å å å å å
R901 R902 R904 R906 R907
VRD-RM2HD105J RR-HZ0014GEZZ RR-WZ0018GEZZ VRD-RM2HD105J VRD-RM2HD333J
Code AB AB AB AB AA AB AA AA AB AB AB AB AB AC AB AG AD AD AB AB AB AB AE AE
COILS AND TRANSFORMER J J J J J
Coil, CiLF0275GE Coil, CiLP0171CE Coil, CiLP0171CE Coil, CiLP0171CE Transformer
AF AD AD AD AM
CAPACITORS MISCELLANEOUS PARTS SC2501 SC2502 SC2504 SC2505
QSOCZ2185GEZZ QSOCZ2185GEZZ QSOCN1996REZZ QSOCN1996REZZ
J J U U
Socket, 20Pin Socket, 20Pin Socket, 19Pin Socket, 19Pin
AF AF AB AB
DUNTKB047TEV1(DV-NC55S/H) DUNTKB087TEV1(DV-NC60H) POWER PWB UNIT INTEGRATED CIRCUITS IC9021 IC9052 IC9053 IC9054 IC9601
VHiPQ15RW21-1 VHiKA7808AP-1 VHiPQ30RV11-1 VHiPQ30RV11-1 VHiKiA431//-1
å å å å å
Q901 Q902 Q903 Q904 Q910 Q9053 Q9054 Q9055 Q9056 Q9057 Q9058 Q9603
VS2SK2848//-1 VS2SC2001LK-1 VS2SC3052EF-1 VS2SC3052EF-1 VS2SC3052EF-1 VS2SB1443TV1E VS2SC2001LK-1 VS2C1740SQR1E VSKRC102S//-1 VSKRA103S//-1 VS2SD471-KL1E VS2SA1530ARS1
å å å å å å
D903 D904 D905 D907 D908 D909
VHD1SS119//-1 VHD10ELS4//-1 VHD1SS119//-1 RH-EX0645GEZZ RH-EX0613GEZZ RH-DX0220CEZZ
J J J J J
PQ15RW21, 5.2V REG KA7808AP, 8VREG PQ30RV11, 3.3V REG PQ30RV11, 1.8V REG KiA431
AK AE AF AF AE
TRANSISTORS J J J J J J J J J J J J
2SK2848 2SC2001LK 2SC3052EF 2SC3052EF 2SC3052EF 2SB1443TV 2SC2001LK 2C1740SQR KRC102S KRA103S 2SD471-KL 2SA1530AR
AH AA AC AC AC AE AA AC AA AA AC AC
DIODES AND LED’S J J J J J J
1SS119 10ELS4 1SS119 Zener, EX0645GE Zener, EX0613GE DX0220CE
AB AD AB AB AA AB
0.1 0.1 2200p 68 100p 1500p 33 3300p 1 100 470 47 47 100 100 1000 10 10 2.2 2.2 220 470 47 470 47 1500 100 2200 470 47 1 0.1 0.01 1
250V M.Polypro 250V M.Polypro AC250V Ceramic 400V Electrolytic 1kV Ceramic 50V Mylar 50V Electrolytic 50V Mylar 400V Electrolytic 6.3V Electrolytic 10V Electrolytic 16V Electrolytic 16V Electrolytic 6.3V Electrolytic 6.3V Electrolytic 16V Electrolytic 16V Electrolytic 16V Electrolytic 50V Electrolytic 50V Electrolytic 16V Electrolytic 10V Electrolytic 63V Electrolytic 35V Electrolytic 35V Electrolytic 16V Electrolytic 25V Electrolytic 10V Electrolytic 10V Electrolytic 50V Electrolytic 50V Electrolytic 25V Ceramic 16V Ceramic 50V Electrolytic
AD AD AD AK AB AA AB AA AD AB AC AB AB AB AB AD AB AB AB AB AC AC AC AB AB AF AB AF AC AB AB AA AA AB
RESISTORS
143
J J J J J
1M 12M 4.7 1M 33k
1/2W 1W 2W 1/2W 1/2W
Carbon AA Alumina Ceramic AE Wire Wound AD Carbon AA Carbon AA
DV-NC55S/H DV-NC60H Ref. No.
★
Part No.
Description
Ref. No.
Code
DUNTKB047TEV1(DV-NC55S/H) DUNTKB087TEV1(DV-NC60H) POWER PWB UNIT(Continued) å å å å å å å å å å å
R908 R909 R910 R911 R912 R914 R915 R916 R920 R922 R930 R9021 R9022 R9054 R9055 R9056 R9058 R9066 R9067 R9068 R9069 R9070 R9071 R9073 R9601 R9602 R9603 R9604 R9605 R9606 R9607 R9608 R9609 R9610 R9611 R9612 R9613 R9614 R9615 R9616 R9618 R9620
VRD-RA2BE563J VRS-CY1JF473J VRS-CY1JF273J VRS-CY1JF223J VRS-CY1JF562J VRD-RA2BE101J VRD-RM2HD152J VRN-VV3DBR22J VRS-CY1JF272J VRS-CY1JF103J VRD-RM2HD105J VRS-CY1JF152F VRS-CY1JF152F VRS-CY1JF103J VRD-RA2EE821J VRD-RA2BE681J VRD-RA2BE271J VRS-CY1JF272F VRS-CY1JF182F VRS-CY1JF333F VRS-CY1JF102F VRS-CY1JF123J VRS-CY1JF222F VRS-CY1JF331J VRS-CY1JF390J VRS-CY1JF273J VRS-CY1JF104J VRS-CY1JF100J VRS-CY1JF121J VRS-CY1JF122J VRS-CY1JF470J VRS-CY1JF152J VRS-CY1JF271J VRS-CY1JF182J VRS-CY1JF152J VRS-CY1JF102J VRS-CY1JF152J VRS-CY1JF102J VRD-RA2BE332J VRS-CY1JF272J VRG-SC2EB1R0J VRS-CY1JF682J
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
56k 47k 27k 22k 5.6k 100 1.5k 0.22 2.7k 10k 1M 1.5k 1.5k 10k 820 680 270 2.7k 1.8k 33k 1k 12k 2.2k 330 39 27k 100k 10 120 1.2k 47 1.5k 270 1.8k 1.5k 1k 1.5k 1k 3.3k 2.7k 1 6.8k
1/8W 1/16W 1/16W 1/16W 1/16W 1/8W 1/2W 2W 1/16W 1/16W 1/2W 1/16W 1/16W 1/16W 1/4W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/4W 1/16W
Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Metal Film Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Fuse Resistor Metal Oxide
J Balun, BLN-0043CE J Balun, BLN-0036CE
FH901 FH902 F901 PDA901 P901 P9001 P9002 P9003 W9001 W9002 W9003 W9004 W9005 å W911 W9011 W9012 W9013 W9014 W9015
QFSHD1014CEZZ QFSHD1013CEZZ QFS-C2025CEZZ PRDAF5021AJFW QPLGN0269GEZZ QPLGN0978GEZZ QPLGN1178GEZZ QPLGN1278GEZZ PRDAR0103AJFW PRDAR0104AJFW PRDAR0104AJFW PRDAR0103AJFW PRDAR0104AJFW XBPSD30P10KS0 XBPSD30P10KS0 XBPSD30P10KS0 XBPSD30P10KS0 XBPSD30P10KS0 XBPSD30P10KS0
J J J J J J J J J J J J J J J J J J J
Fuse Holder Fuse Holder Fuse, 2A 250V Heat Sink Plug, 3Pin Plug, 9Pin Plug, 11Pin Plug, 12Pin Heat Sink Heat Sink Heat Sink Heat Sink Heat Sink Screw Screw Screw Screw Screw Screw
Code
INTEGRATED CIRCUITS
AA AA AA AA AA AB AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA
IC6001 IC6004 IC6101 IC8201 IC8202
VHiPCM1737E-1 VHiNJM4565M-1~ VHiTC4W53F/-1 RH-iX1757GEZZQ VHiPST600H/-1
Q6002 Q6003 Q6004 Q6005 Q6006 Q6007 Q6008 Q6009 Q6020 Q6101 Q6102 Q8201 Q8202 Q8203 Q8204 Q8205 Q8206 Q8207 Q8209
VS2SA1530ARS1 VSKRC104S//-1 VSKRA103S//-1 VSKRC104S//-1 VSKRA103S//-1 VS2SD1306-E-1 VS2SD1306-E-1 VSKRC104S//-1 VSKRA103S//-1 VS2SC3052EF-1 VSKRC103S//-1 VSKRA103S//-1 VS2SC3052EF-1 VS2SC3203Y/-1 VSKRA103S//-1 VSKRC103S//-1 VSKRC103S//-1 VSKRC103S//-1 VSKRA102S//-1
D6001 D6002 D6003 D6101 D8201 D8202 D8203
VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-EX0609GEZZ VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1
J J J J J
PCM1737E, Audio DAC NJM4565M, Audio Amp TC4W53F IX1757GE, Interface CPU PST600H, Reset IC
AS AD AE AQ AE
TRANSISTORS J J J J J J J J J J J J J J J J J J J
2SA1530AR KRC104S KRA103S KRC104S KRA103S 2SD1306-E 2SD1306-E KRC104S KRA103S 2SC3052EF KRC103S KRA103S 2SC3052EF 2SC3203Y KRA103S KRC103S KRC103S KRC103S KRA102S
AC AA AA AA AA AC AC AA AA AC AA AA AC AB AA AA AA AA AA
DIODES J J J J J J J
1SS119 1SS119 1SS119 Zener, EX0609GE 1SS119 1SS119 1SS119
AB AB AB AA AB AB AB
FILTERS FL6101 RFiLN0044GEZZ FL8201 RFiLC0198GEZZ
J Filter, FiLN0044GE J Filter, FiLC0198GE
AB AE
COIL
AB AB
L6101
VP-MK100K0000
C6001 C6002 C6003 C6006 C6007 C6008 C6009 C6010 C6011 C6012 C6013 C6014 C6015 C6025 C6026 C6027 C6028 C6029 C6030 C6031 C6032 C6033 C6034 C6035 C6036
VCEA9M0JW476M VCKYCY1HF103Z VCKYCY1CB104K VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW106M VCCCCY1HH470J VCKYCY1EF104Z VCEA9M1CW106M VCEA9M0JW227M VCKYCY1CB104K VCQYTA1HM561J VCQYTA1HM561J VCEA9M1CW106M VCKYCY1HF103Z VCKYCY1HF103Z VCEA9M0JW227M VCEA2A0JW477M VCEA9M1CW106M VCEA9A1CW106M VCEA9M1CW106M VCEA9M1CW226M VCEA9M1CW226M VCQYTA1HM822J VCQYTA1HM822J
J Peaking, 10µH
AB
CAPACITORS
MISCELLANEOUS PARTS å å å å
Description
DUNTKB040TEV1(DV-NC55S/H) DUNTKB084TEV1(DV-NC60H) INTERFACE PWB UNIT
BALUNES å FB902 RBLN-0043CEZZ FB9001 RBLN-0036CEZZ
★
Part No.
AC AC AD AE AB AC AC AC AE AD AD AE AD AA AA AA AA AA AA
144
J J J J J J J J J J J J J J J J J J J J J J J J J
47 0.01 0.1 10 10 10 47p 0.1 10 220 0.1 560p 560p 10 0.01 0.01 220 470 10 10 10 22 22 8200p 8200p
6.3V 50V 16V 16V 16V 16V 50V 25V 16V 6.3V 16V 50V 50V 16V 50V 50V 6.3V 6.3V 16V 16V 16V 16V 16V 50V 50V
Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Mylar Mylar Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Mylar Mylar
AB AA AB AB AB AB AA AA AB AB AB AB AB AB AA AA AB AB AB AB AB AB AB AA AA
DV-NC55S/H DV-NC60H Ref. No.
★
Part No.
Description
Code
Ref. No.
DUNTKB040TEV1(DV-NC55S/H) DUNTKB084TEV1(DV-NC60H) INTERFACE PWB UNIT(Continued) C6049 C6050 C6051 C6052 C6080 C6081 C6101 C6103 C6104 C6105 C6106 C6109 C6110 C6111 C6112 C6113 C8201 C8202 C8203 C8204 C8205 C8206 C8208 C8209 C8214 C8215 C8216 C8217
VCCCCY1HH221J VCCCCY1HH221J VCCCCY1HH221J VCCCCY1HH221J VCKYCY1HB102K VCKYCY1CB104K VCKYCY1EB103K VCEA9M1CW106M VCKYCY1EB103K VCKYCY1CB104K VCEA9M1CW106M VCCCCY1HH470J VCEA9M0JW107M VCCCCY1HH470J VCEA9M1CW106M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB102K VCEA9M1HW105M VCEA9M0JW476M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCCCD41HH100J VCCCD41HH100J VCCCD41HH100J VCKYD41HF104Z
RJ47 R6010 R6011 R6012 R6029 R6030 R6031 R6036 R6037 R6042 R6043 R6044 R6045 R6046 R6047 R6048 R6049 R6050 R6051 R6052 R6053 R6054 R6055 R6056 R6057 R6058 R6101 R6102 R6103 R6104 R6105 R6106 R6107 R6108 R6110 R8201 R8202 R8203 R8204 R8205 R8206
VRS-CY1JF000J VRD-RM2HD220J VRS-CY1JF472J VRS-CY1JF472J VRD-RA2BE222J VRS-CY1JF222J VRS-CY1JF152J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF153J VRS-CY1JF153J VRS-CY1JF474J VRS-CY1JF474J VRS-CY1JF153J VRS-CY1JF153J VRS-CY1JF331J VRS-CY1JF331J VRS-CY1JF473J VRS-CY1JF473J VRS-CY1JF272J VRD-RA2BE272J VRD-RA2BE332J VRS-CY1JF103J VRS-CY1JF153J VRS-CY1JF103J VRS-CY1JF153J VRS-CY1JF000J VRS-CY1JF272J VRD-RM2HD101J VRD-RA2BE151J VRD-RA2BE103J VRS-CY1JF681J VRS-CY1JF183J VRD-RA2BE273J VRS-CY1JF472J VRS-CY1JF104J VRS-CY1JF103J VRS-CY1JF473J VRD-RA2BE103J VRS-CY1JF103J VRS-CY1JF103J
J J J J J J J J J J J J J J J J J J J J J J J J J J J J
220p 220p 220p 220p 1000p 0.1 0.01 10 0.01 0.1 10 47p 100 47p 10 0.01 0.01 0.01 1000p 1 47 0.01 0.01 0.01 10p 10p 10p 0.1
50V 50V 50V 50V 50V 16V 25V 16V 25V 16V 16V 50V 6.3V 50V 16V 50V 50V 50V 50V 50V 6.3V 50V 50V 50V 50V 50V 50V 50V
Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic
AA AA AA AA AA AB AA AB AA AB AB AA AB AA AB AA AA AA AA AB AB AA AA AA AB AB AB AA
0 22 4.7k 4.7k 2.2k 2.2k 1.5k 1k 1k 15k 15k 470k 470k 15k 15k 330 330 47k 47k 2.7k 2.7k 3.3k 10k 15k 10k 15k 0 2.7k 100 150 10k 680 18k 27k 4.7k 100k 10k 47k 10k 10k 10k
1/16W 1/2W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/2W 1/8W 1/8W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W
Metal Oxide Carbon Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Carbon Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide
R8207 R8208 R8209 R8210 R8211 R8212 R8213 R8214 R8215 R8216 R8217 R8218 R8219 R8220
VRS-CY1JF473J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF473J VRD-RA2BE473J VRS-CY1JF473J VRS-CY1JF473J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF682J VRS-CY1JF682J
FB6001 FB6002 FB6004 FB6005 FB6006 FB6101 FB6102 FB6103 FB6104 FB8201
RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0077TAZZ
CN6101 CN6102 CN8201 CN8202 CN8203
PSLDM9385AJZZ QPLGN0278GEZZ QSOCN0995REZZ QPLGN1178GEZZ QSOCN2999REZZ QSOCN0620FJZZ
J J J J J J J J J J J J J J
Description 47k 10k 10k 47k 47k 47k 47k 10k 4.7k 4.7k 10k 10k 6.8k 6.8k
1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
Code
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA
BALUNES J J J J J J J J J J
Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0077TA
AB AB AB AB AB AB AB AB AB AB
MISCELLANEOUS PARTS
RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
★
Part No.
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
J J J J J J
Shield Plug, 2Pin Socket, 9Pin Plug, 11Pin Socket, 29Pin Socket, 23Pin
AE AA AC AC AE AE
DUNTKB043TEV1(DV-NC55H/60H) DUNTKB043TEV2(DV-NC55S) VCR MAIN PWB UNIT TUNERS TU1401 VTUATMDG2-602 TU1401 VTUATMDB2-602
J VHF/UHF Tuner(NC55S) J UHF Tuner(NC55H/60H)
BG BF
INTEGRATED CIRCUITS IC201
VHiHA8617F/-1
J HA8617F, Y/C Audio Processor IC681 VHiTC4S66F/-1 J TC4S66F IC701 RH-iXA082WJZZQ U IXA082WJ IC703 VHiPST600K/-1 J PST600K IC705 VHiBR2416E2-1 J BR2416E2, E2PROM IC1201 VHiMM1508XN-1 J MM1508XN, Y Driver IC1202 VHiMM1506XN-1 J MM1506XN, C Driver IC1206 VHiMM1508XN-1 J MM1508XN, COMP. Driver IC1701 VHiMSP3417G-1Q J MSP3417G, MPX Decoder IC1801 VHiLC74793J1E J LC74793J, VPS/PDC IC6301 VHiLA72634M-1 J LA72634M, Hi-Fi Audio Processor IC7002 VHiLB11880+-1 J LB11880+, Loading/Drum M Driver IC
AX AD AE AE AK AE AE AE AY AV AR AL
TRANSISTORS Q201 Q205 Q301 Q302 Q303 Q501 Q502 Q503 Q581 Q582 Q601
145
VS2PD601AR/-1 VSUN2213///-1 VS2PD601AR/-1 VSUN2113///-1 VS2PD601AR/-1 VS2PD601AR/-1 VS2SK1826++-1 VSUN2213///-1 VSUN2111///-1 VSUN2211///-1 VS2PB709AR/-1
J J J J J J J J J J J
2PD601AR UN2213 2PD601AR UN2113 2PD601AR 2PD601AR 2SK1826++ UN2213 UN2111 UN2111 2PB709AR
AB AA AB AA AB AB AC AA AA AA AB
DV-NC55S/H DV-NC60H Ref. No.
Part No.
★
Description
Code
DUNTKB043TEV1(DV-NC55H/60H) DUNTKB043TEV2(DV-NC55S) VCR MAIN PWB UNIT(Continued) Q602 Q603 Q604 Q605 Q651 Q652 Q681 Q682 Q703 Q704 Q708 Q711 Q712 Q713 Q9903 Q9905 Q9906 Q9907 Q9908 Q9909 Q9910 Q9916
VS2SD1306-E1E VSUN2112///-1 VS2PD601AR/-1 VS2PD601AR/-1 VS2SC3203Y/-1 VS2PD601AR/-1 VSUN2211///-1 VSUN2111///-1 VS2PB709AR/-1 VSUN2212///-1 VS2PB709AR/-1 VS2PD601AR/-1 VS2PD601AR/-1 VSUN2211///-1 VS2SD471-KL1E VSUN2211///-1 VS2PB709AR/-1 VS2SA1706ST1E VSUN2211///-1 VS2PB709AR/-1 VSUN2211///-1 VS2SD471-KL1E
D701 D702 D704 D705 D708 D709 D710 D711 D712 D9701 D9902 D9903 D9904 D9908 D9909 D9910 D9912 Q701 Q702
RH-PX0270GEZZ VHD1SS119//-1 VHD1SS119//-1 RH-PX0238GEZZ RH-PX0238GEZZ VHD1SS119//-1 VHD1SS119//-1 RH-PX0252GEZZ RH-PX0252GEZZ RH-EX0601GEZZ VHD1SS119//-1 RH-EX0720GEZZ RH-EX0677GEZZ RH-EX0610GEZZ RH-EX0611GEZZ RH-DX0220CEZZ VHD1SS119//-1 RH-PX0233GEZZ RH-PX0233GEZZ
X501 X701 X702 X1701
RCRSB0232GEZZ RCRSB0205GEZZ RCRSB0138GEN1 RCRSB0249GEZZ
L201 L301 L302 L304 L351 L502 L503 L581 L651 L707 L1401 L1403 L1404 L1407 L1703 L1704 å T651
VP-XF181J0000 VP-MK101K0000 VP-MK180J0000 VP-XF120J0000 VP-MK101K0000 VP-XF560J0000 VP-XF120J0000 VP-XF101K0000 VP-DF221K0000 VP-XF100J0000 VP-CF100K0000 VP-XF100J0000 VP-XF100J0000 VP-XF100J0000 VP-XF100J0000 VP-XF100J0000 RTRNH0098GEZZ
J J J J J J J J J J J J J J J J J J J J J J
2SD1306-E UN2112 2PD601AR 2PD601AR 2SC3203Y 2PD601AR UN2211 UN2211 2PB709AR UN2212 2PB709AR 2PD601AR 2PD601AR UN2211 2SD471-KL UN2211 2PB709AR 2SA1706ST UN2211 2PB709AR UN2211 2SD471-KL
PhotoDiode, Cassette LED 1SS119(NC55S) 1SS119 PX0238GE PX0238GE 1SS119 1SS119 PX0252GE PX0252GE Zener, EX0601GE 1SS119 Zener, EX0720GE Zener, EX0677GE Zener, EX0610GE Zener, EX0611GE DX0220CE 1SS119 PX0233GE PX0233GE
AD AA AB AB AB AB AA AA AB AA AB AB AB AA AC AA AB AE AA AB AA AC
AC AB AB AF AF AB AB AF AF AA AB AB AB AA AA AB AB AD AD
PACKAGED CIRCUITS J J J J
Crystal, CRSB0232GE Crystal, CRSB0205GE Crystal, CRSB0138GE Crystal, CRSB0249GE
AG AM AD AF
COILS AND TRANSFORMER J J J J J J J J J J J J J J J J J
Peaking, 180µH Peaking, 100µH Peaking, 18µH Peaking, 12µH Peaking, 100µH Peaking, 56µH Peaking, 12µH Peaking, 100µH Peaking, 220µH Peaking, 10µH Peaking, 10µH Peaking, 10µH Peaking, 10µH Peaking, 10µH Peaking, 10µH Peaking, 10µH OSC. Transformer
Part No.
C201 C202 C203 C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C217 C218 C219 C220 C221 C222 C223 C225 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C316 C317 C318 C319 C320 C326 C327 C328 C329 C330 C351 C352 C353 C354 C355 C356 C357 C399 C501 C502 C503 C504 C505 C506 C507 C508 C509 C512 C513 C514 C515 C516 C517 C518 C519 C520 C521 C522
VCEA9M0JW107M VCKYCY1EF104Z VCCCCY1HH121J VCKYCY1EF104Z VCCCCY1HH220J VCKYCY1EF104Z VCKYCY1EF104Z VCEA9M1HW105M VCKYCY1EF104Z VCKYCY1EF104Z VCEA9M1HW335M VCEA9M1CW106M VCEA9M1HW225M VCKYCY1EF104Z VCKYD41CF105Z VCEA9M0JW107M VCKYCY1HF103Z VCKYCY1EF104Z VCKYCY1EF104Z VCEA9M1CW106M VCKYCY1EF104Z VCEA9M0JW107M VCCCCY1HH220J VCEA9M0JW476M VCKYCY1EF104Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1CB393K VCKYCY1EB123K VCKYCY1HB222K VCCCCY1HH220J VCCCCY1HH120J VCCCCY1HH220J VCCCCY1HH3R0C VCCCCY1HH3R0C VCCCCY1HH220J VCCCCY1HH150J VCCCCY1HH150J VCKYCY1EF104Z VCKYCY1EF104Z VCEA9M0JW476M VCKYCY1EB123K VCKYCY1HB561K VCKYCY1EB123K VCKYD41CF105Z VCCCCY1HH820J VCCCCY1HH560J VCKYCY1EF104Z VCEA9M0JW107M VCKYCY1EF104Z VCKYCY1CB104K VCEA9M1HW225M VCKYCY1CB273K VCKYCY1AB474K VCKYCY1EF104Z VCEA9M1HW475M VCKYCY1CB393K VCKYD41CY103N VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB331K VCCCCY1HH120J VCEA9M1HW335M VCKYCY1CB393K VCEA9M1HW105M VCKYCY1EF104Z VCCCCY1HH6R0D VCKYCY1HF103Z
Description
Code
CAPACITORS
DIODES AND LED’S J J J J J J J J J J J J J J J J J J J
★
Ref. No.
AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AE
146
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
100 0.1 120p 0.1 22p 0.1 0.1 1 0.1 0.1 3.3 10 2.2 0.1 1 100 0.01 0.1 0.1 10 0.1 100 22p 47 0.1 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.039 0.012 2200p 22p 12p 22p 3p 3p 22p 15p 15p 0.1 0.1 47 0.012 560p 0.012 1 82p 56p 0.1 100 0.1 0.1 2.2 0.027 0.47 0.1 4.7 0.039 0.01 0.01 0.01 330p 12p 3.3 0.039 1 0.1 6p 0.01
6.3V 25V 50V 25V 50V 25V 25V 50V 25V 25V 50V 16V 50V 25V 16V 6.3V 50V 25V 25V 16V 25V 6.3V 50V 6.3V 25V 50V 50V 50V 50V 50V 50V 50V 50V 16V 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 25V 6.3V 25V 50V 25V 16V 50V 50V 25V 6.3V 25V 16V 50V 16V 10V 25V 50V 16V 16V 50V 50V 50V 50V 50V 16V 50V 25V 50V 50V
Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic
AB AA AA AA AA AA AA AB AA AA AB AB AB AA AB AB AA AA AA AB AA AB AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AB AA AA AA AB AA AB AB AA AC AA AB AA AA AA AA AA AA AB AA AB AA AA AA
DV-NC55S/H DV-NC60H Ref. No.
Part No.
★
Description
Code
Ref. No.
DUNTKB043TEV1(DV-NC55H/60H) DUNTKB043TEV2(DV-NC55S) VCR MAIN PWB UNIT(Continued) C523 C581 C602 C603 C604 C605 C606 C607 C608 C609 C610 C611 C612 C622 C623 C624 C625 C626 C627 C628 C629 C651 C652 C653 C654 C655 C681 C682 C713
VCKYCY1HF103Z VCCCCY1HH270J VCKYCY1EB123K VCEA9M0JW226M VCKYCY1HB102K VCEA9M1HW335M VCEA9M1CW106M VCEA9M1HW475M VCEA9M0JW226M VCEA9M1HW474M VCEA9M1HW105M VCEA9M1HW105M VCEA9M1HW105M VCKYCY1HB102K VCKYCY1HB331K VCKYCY1HB682K VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH221J VCKYCY1HB222K VCKYD41CF105Z VCQPKA2AA562J VCKYCY1EB103K VCKYCY1EB103K VCEA9M1CW106M VCEA9M1CW476M VCKYCY1HB472K VCEA9M1CW106M RC-EZ0426GEZZ
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
C714 C715 C722 C723 C724 C728 C729 C730 C731 C732 C735 C736 C737 C739 C740 C741 C742 C743 C744 C745 C746 C747 C748 C749 C754 C755 C756 C757 C758 C760 C761 C762 C763 C765 C768 C769 C770 C771 C773 C774 C775
VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB472K VCKYCY1EF104Z VCKYCY1EF104Z VCEA9M0JW226M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1HB102K VCKYCY1HB102K VCCCCY1HH221J VCKYCY1HB102K VCKYCY1HF103Z VCKYCY1HB222K VCKYCY1HF103Z VCKYD41CY103N VCEA9M1HW105M VCKYCY1AF105Z VCKYCY1EF104Z VCEA9M0JW227M VCEA9M1HW105M VCCCCY1HH101J VCKYCY1HF103Z VCKYCY1EB223K VCCCCY1HH220J VCCCCY1HH150J VCCCCY1HH150J VCCCCY1HH120J VCKYCY1EB103K VCKYCY1AF105Z VCEA0A0JW108M VCEA9M0JW226M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1EB103K VCKYCY1EF104Z VCKYCY1CB473K VCKYCY1HB102K VCEA9M0JW227M VCEA9M0JW107M VCKYCY1HB102K
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
0.01 50V Ceramic 27p 50V Ceramic 0.012 25V Ceramic 22 6.3V Electrolytic 1000p 50V Ceramic 3.3 50V Electrolytic 10 16V Electrolytic 4.7 50V Electrolytic 22 6.3V Electrolytic 0.47 50V Electrolytic 1 50V Electrolytic 1 50V Electrolytic 1 50V Electrolytic 1000p 50V Ceramic 330p 50V Ceramic 6800p 50V Ceramic 100p 50V Ceramic 100p 50V Ceramic 220p 50V Ceramic 2200p 50V Ceramic 1 16V Ceramic 5600p 100V Mylar 0.01 25V Ceramic 0.01 25V Ceramic 10 16V Electrolytic 47 16V Electrolytic 4700p 50V Ceramic 10 16V Electrolytic 0.1 5.5V Electrolytic (NC55S) 0.01 50V Ceramic 0.01 50V Ceramic 4700p 50V Ceramic 0.1 25V Ceramic 0.1 25V Ceramic 22 6.3V Electrolytic 0.1 25V Ceramic 0.1 25V Ceramic 1000p 50V Ceramic 1000p 50V Ceramic 220p 50V Ceramic 1000p 50V Ceramic 0.01 50V Ceramic 2200p 50V Ceramic 0.01 50V Ceramic 0.01 16V Ceramic 1 50V Electrolytic 1 10V Ceramic 0.1 25V Ceramic 220 6.3V Electrolytic 1 50V Electrolytic 100p 50V Ceramic 0.01 50V Ceramic 0.022 25V Ceramic 22p 50V Ceramic 15p 50V Ceramic 15p 50V Ceramic 12p 50V Ceramic 0.01 25V Ceramic 1 10V Ceramic 1000 6.3V Electrolytic 22 6.3V Electrolytic 0.01 50V Ceramic 0.01 50V Ceramic 0.01 25V Ceramic 0.1 25V Ceramic 0.047 16V Ceramic 1000p 50V Ceramic 220 6.3V Electrolytic 100 6.3V Electrolytic 1000p 50V Ceramic
C776 C780 C781 C794 C795 C796 C797 C798 C1201 C1202 C1203 C1204 C1205 C1206 C1207 C1208 C1220 C1221 C1222 C1223 C1224 C1401 C1402 C1404 C1405 C1406 C1407 C1409 C1411 C1701 C1702 C1704 C1705 C1706 C1707 C1708 C1709 C1710 C1711 C1712 C1713 C1714 C1715 C1718 C1720 C1723 C1730 C1731 C1735 C1738 C1753 C1803 C1804 C1805 C1806 C1807 C1811 C1812 C6301 C6302 C6303 C6304 C6305 C6306 C6307 C6308 C6309 C6310 C6313 C6314 C6315 C6316 C6317 C6318 C6319
AA AA AA AB AA AB AB AB AB AB AB AB AB AA AA AA AA AA AA AA AB AB AA AA AB AB AA AB AG AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AB AC AA AB AB AA AA AA AA AA AA AA AA AC AC AB AA AA AA AA AA AA AB AB AA
147
Part No.
★
VCKYCY1EF104Z J VCKYCY1CB473K J VCKYCY1EB103K J VCCCCY1HH6R0D J VCCCCY1HH120J J VCCCCY1HH390J J VCKYCY1EF104Z J VCKYCY1HB682K J VCEA9A1HW105M J VCKYCY1CB104K J VCEA0A0JW477M J VCKYCY1EB103K J VCEA9M0JW227M J VCKYD41CY103N J VCKYCY1CB104K J VCKYCY1CF104Z J VCEA9M1HW105M J VCKYCY1CB104K J VCEA0A0JW477M J VCKYCY1CB104K J VCEA9M0JW107M J VCEA9M0JW227M J VCKYCY1HF103Z J VCEA9M0JW107M J VCEA9M0JW107M J VCEA9M1HW105M J VCKYCY1EF104Z J VCKYCY1HF103Z J VCKYCY1HB682K J VCCSD41HL220J J VCCCCY1HH470J J VCKYCY1HF103Z J VCEA9M1CW106M J VCKYCY1HF103Z J VCEA9M1CW106M J VCEA9M0JW226M J VCEA9M1AW226M+J VCCCCY1HH5R0C J VCCCCY1HH6R0D J VCKYCY1HF103Z J VCKYCY1HF103Z J VCEA9M1HW105M J VCKYCY1HF103Z J VCEA9M0JW226M J VCCCCY1HH470J J VCEA9M1CW106M J VCEA9M1CW106M J VCEA9M1CW106M J VCKYCY1HB122K J VCKYCY1HB122K J VCKYD41HB331K J VCQYTA1HM563J J VCEA9M1HW475M J VCKYD41CF105Z J VCEA9M1HW105M J VCKYD41CY103N J VCEA9M0JW476M J VCKYCY1HF103Z J VCEA9M1CW106M J VCEA9M1HW105M J VCEA9M1CW106M J VCEA9M1HW475M J VCKYCY1EB103K J VCEA9M0JW226M J VCEA9M0JW226M J VCKYCY1HB472K J VCKYCY1HB332K J VCKYCY1CF334Z J VCEA9M0JW476M J VCKYCY1HB332K J VCKYCY1HB472K J VCEA9M0JW226M J VCKYCY1EB103K J VCEA9M1HW475M J VCEA9M1CW106M J
Description 0.1 0.047 0.01 6p 12p 39p 0.1 6800p 1 0.1 470 0.01 220 0.01 0.1 0.1 1 0.1 470 0.1 100 220 0.01 100 100 1 0.1 0.01 6800p 22p 47p 0.01 10 0.01 10 22 22 5p 6p 0.01 0.01 1 0.01 22 47p 10 10 10 1200p 1200p 330p 0.056 4.7 1 1 0.01 47 0.01 10 1 10 4.7 0.01 22 22 4700p 3300p 0.33 47 3300p 4700p 22 0.01 4.7 10
25V 16V 25V 50V 50V 50V 25V 50V 50V 16V 6.3V 25V 6.3V 16V 16V 16V 50V 16V 6.3V 16V 6.3V 6.3V 50V 6.3V 6.3V 50V 25V 50V 50V 50V 50V 50V 16V 50V 16V 6.3V 10V 50V 50V 50V 50V 50V 50V 6.3V 50V 16V 16V 16V 50V 50V 50V 50V 50V 16V 50V 16V 6.3V 50V 16V 50V 16V 50V 25V 6.3V 6.3V 50V 50V 16V 6.3V 50V 50V 6.3V 25V 50V 16V
Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Mylar Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Electrolytic Electrolytic
Code AA AA AA AA AA AA AA AA AB AB AC AA AB AA AB AA AB AB AC AB AB AB AA AB AB AB AA AA AA AA AA AA AB AA AB AB AB AA AA AA AA AB AA AB AA AB AB AB AA AA AA AB AB AB AB AA AB AA AB AB AB AB AA AB AB AA AA AA AB AA AA AB AA AB AB
DV-NC55S/H DV-NC60H Ref. No.
★
Part No.
Description
Ref. No.
Code
DUNTKB043TEV1(DV-NC55H/60H) DUNTKB043TEV2(DV-NC55S) VCR MAIN PWB UNIT(Continued) C6320 C6322 C6323 C6324 C6327 C6328 C7002 C7003 C7004 C7005 C7006 C7007 C7009 C7011 C7012 C7016 C7019 C7020 C7023 C7091 C7092 C8008 C8009 C9701 C9901 C9903 C9908
VCEA9M1HW105M VCEA9M1CW106M VCEA9M1CW106M VCEA9M1CW107M VCEA9M1HW105M VCEA9M1HW105M VCKYCY1EB223K VCKYCY1EB223K VCKYCY1EB223K VCEAGA1VW107M VCEA9M1CW476M VCKYD41CF105Z VCKYCY1EB103K VCFYSA1HB474J VCKYCY1CF334Z VCKYCY1HB102K VCKYD41HF104Z VCEA9M0JW476M VCKYCY1EF104Z VCKYCY1HB392K VCKYCY1HB392K VCCCCY1HH101J VCCCCY1HH101J VCFYSA1HB474J VCEA9M1CW476M VCEA9M1HW105M VCEA9M1CW107M
RJ1205 RJ5002 RJ7007 R201 R202 R203 R204 R207 R208 R209 R210 R247 R248 R301 R303 R305 R306 R312 R313 R314 R315 R351 R352 R353 R501 R502 R504 R505 R506 R507 R508 R509 R510 R601 R602 R603 R604 R605 R606 R607 R608 R609
VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF682J VRS-CY1JF182J VRS-CY1JF822J VRD-RA2BE562J VRS-CY1JF102J VRD-RA2BE471J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF223J VRS-CY1JF223J VRS-CY1JF473J VRS-CY1JF392J VRS-CY1JF102J VRS-CY1JF681J VRS-CY1JF681J VRS-CY1JF333J VRS-CY1JF182J VRS-CY1JF682J VRS-CY1JF471J VRS-CY1JF272J VRS-CY1JF224J VRS-CY1JF102J VRS-CY1JF273J VRS-CY1JF221J VRS-CY1JF224J VRS-CY1JF272J VRS-CY1JF272J VRS-CY1JF472J VRS-CY1JF154J VRS-CY1JF154J VRS-CY1JF183J VRS-CY1JF274J VRS-CY1JF181J VRS-CY1JF473J VRS-CY1JF153J VRS-CY1JF333J VRS-CY1JF682J VRS-CY1JF122J VRS-CY1JF224J
J J J J J J J J J J J J J J J J J J J J J J J J J J J
1 10 10 100 1 1 0.022 0.022 0.022 100 47 1 0.01 0.47 0.33 1000p 0.1 47 0.1 3900p 3900p 100p 100p 0.47 47 1 100
50V 16V 16V 16V 50V 50V 25V 25V 25V 35V 16V 16V 25V 50V 16V 50V 50V 6.3V 25V 50V 50V 50V 50V 50V 16V 50V 16V
Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Mylar Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Mylar Electrolytic Electrolytic Electrolytic
AB AB AB AB AB AB AA AA AA AC AB AB AA AC AA AA AA AB AA AA AA AA AA AC AB AB AB
RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
0 0 0 6.8k 1.8k 8.2k 5.6k 1k 470 4.7k 1k 22k 22k 47k 3.9k 1k 680 680 33k 1.8k 6.8k 470 2.7k 220k 1k 27k 220 220k 2.7k 2.7k 4.7k 150k 150k 18k 270k 180 47k 15k 33k 6.8k 1.2k 220k
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
148
Part No.
★
R610 R611 R612 R613 R614 R615 R616 R617 R619 R620 R624 R625 R654 R655 R656 R657 R658 R659 R681 R682 R683 R707 R708 R709
VRS-CY1JF473J VRS-CY1JF562J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF473J VRS-CY1JF101J VRS-CY1JF333J VRS-CY1JF682J VRS-CY1JF393J VRS-CY1JF123J VRS-CY1JF472J VRS-CY1JF222J VRD-RA2BE392J VRD-RA2BE273J VRS-CY1JF470J VRS-CY1JF682J VRD-RA2EE4R7J VRS-CY1JF101J VRS-CY1JF183J VRS-CY1JF182J VRS-CY1JF122J VRS-CY1JF123J VRS-CY1JF123J VRD-RA2EE680J
J J J J J J J J J J J J J J J J J J J J J J J J
R710 R712 R713 R719 R722 R723 R724 R725 R726 R727 R728 R730 R731 R732 R733 R734 R735 R736 R738 R741 R742 R743 R745 R746 R748 R749 R750 R751 R752 R753 R754 R755 R756 R759 R760 R761 R763 R764 R765 R766 R767 R768 R769 R770 R771 R772 R773 R774 R775 R776
VRD-RA2BE151J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF102J VRD-RA2BE332J VRS-CY1JF681J VRS-CY1JF104J VRS-CY1JF182J VRS-CY1JF104J VRS-CY1JF562J VRS-CY1JF562J VRS-CY1JF472J VRS-CY1JF101J VRS-CY1JF222J VRS-CY1JF564J VRS-CY1JF154J VRS-CY1JF473J VRS-CY1JF332J VRS-CY1JF104J VRD-RA2BE271J VRS-CY1JF473J VRS-CY1JF223J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF154J VRS-CY1JF152J VRD-RA2BE151J VRS-CY1JF822J VRS-CY1JF104J VRS-CY1JF223J VRD-RA2BE271J VRS-CY1JF223J VRS-CY1JF223J VRS-CY1JF222J VRS-CY1JF103J VRS-CY1JF151J VRS-CY1JF104J VRS-CY1JF563J VRS-CY1JF332J VRS-CY1JF473J VRS-CY1JF273J VRS-CY1JF391J VRS-CY1JF473J VRS-CY1JF391J VRS-CY1JF151J
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
Description 47k 1/16W 5.6k 1/16W 100k 1/16W 100k 1/16W 47k 1/16W 100 1/16W 33k 1/16W 6.8k 1/16W 39k 1/16W 12k 1/16W 4.7k 1/16W 2.2k 1/16W 3.9k 1/8W 27k 1/8W 47 1/16W 6.8k 1/16W 4.7 1/4W 100 1/16W 18k 1/16W 1.8k 1/16W 1.2k 1/16W 12k 1/16W 12k 1/16W 68 1/4W (NC55S) 150 1/8W 10k 1/16W 0 1/16W 1k 1/16W 1k 1/16W 10k 1/16W 10k 1/16W 1k 1/16W 1k 1/16W 3.3k 1/8W 680 1/16W 100k 1/16W 1.8k 1/16W 100k 1/16W 5.6k 1/16W 5.6k 1/16W 4.7k 1/16W 100 1/16W 2.2k 1/16W 560k 1/16W 150k 1/16W 47k 1/16W 3.3k 1/16W 100k 1/16W 270 1/8W 47k 1/16W 22k 1/16W 10k 1/16W 10k 1/16W 150k 1/16W 1.5k 1/16W 150 1/8W 8.2k 1/16W 100k 1/16W 22k 1/16W 270 1/8W 22k 1/16W 22k 1/16W 2.2k 1/16W 10k 1/16W 150 1/16W 100k 1/16W 56k 1/16W 3.3k 1/16W 47k 1/16W 27k 1/16W 390 1/16W 47k 1/16W 390 1/16W 150 1/16W
Code
Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Carbon Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
DV-NC55S/H DV-NC60H Ref. No.
Part No.
★
Description
Code
Ref. No.
DUNTKB043TEV1(DV-NC55H/60H) DUNTKB043TEV2(DV-NC55S) VCR MAIN PWB UNIT(Continued) R777 R778 R779 R787 R788 R789 R790 R791 R798 R799 R801 R816 R817 R1203 R1204 R1208 R1210 R1211 R1401 R1404 R1405 R1703 R1710 R1711 R1714 R1720 R1723 R1801 R1807 R1808 R1810 R1861 R6305 R6307 R6308 R6309 R6310 R6317 R6318 R6319 R6320 R6321 R6322 R6323 R6324 R6325 R6327 R6328 R6329 R7001 R7002 R7003 R7004 R7005 R7006 R7011 R7018 R7047 R8009 R8010 R8011 R8012 R8013 R8014 R8015 R8016 R9703 R9807 R9901 R9907 R9908
VRS-CY1JF104J VRS-CY1JF221J VRS-CY1JF221J VRD-RA2BE473J VRS-CY1JF154J VRS-CY1JF155J VRD-RA2BE102J VRD-RA2BE102J VRS-CY1JF271J VRS-CY1JF102J VRS-CY1JF562J VRS-CY1JF183J VRS-CY1JF183J VRS-CY1JF750J VRS-CY1JF750J VRS-CY1JF750J VRS-CY1JF821J VRS-CY1JF821J VRD-RA2BE154J VRS-CY1JF562J VRS-CY1JF272J VRD-RA2BE473J VRD-RA2BE101J VRD-RA2BE101J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF272J VRS-CY1JF562J VRS-CY1JF103J VRS-CY1JF473J VRS-CY1JF103J VRS-CY1JF331J VRS-CY1JF331J VRS-CY1JF472J VRS-CY1JF103J VRD-RA2BE153J VRS-CY1JF152J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF272J VRS-CY1JF102J VRS-CY1JF272J VRD-RA2BE153J VRS-CY1JF152J VRS-CY1JF333J VRS-CY1JF333J VRD-RA2BE221J VRS-CY1JF103J VRS-CY1JF103J VRD-RA2EE1R0J VRS-CY1JF392J VRS-CY1JF104J VRS-CY1JF564J VRG-SC2EB1R0J VRD-RA2EE1R0J VRS-CY1JF105J VRS-CY1JF101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE223J VRS-CY1JF100J VRD-RA2BE820J VRD-RA2BE103J VRS-CY1JF103J
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
100k 220 220 47k 150k 1.5M 1k 1k 270 1k 5.6k 18k 18k 75 75 75 820 820 150k 5.6k 2.7k 47k 100 100 1k 10k 10k 10k 2.7k 5.6k 10k 47k 10k 330 330 4.7k 10k 15k 1.5k 0 1k 2.7k 1k 2.7k 15k 1.5k 33k 33k 220 10k 10k 1 3.9k 100k 560k 1 1 1M 100 100 100 100 100 100 100 100 22k 10 82 10k 10k
1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/8W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/4W 1/16W 1/16W 1/16W 1/4W 1/4W 1/16W 1/16W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/16W 1/8W 1/8W 1/16W
Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Carbon Carbon Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Carbon Metal Oxide Metal Oxide Metal Oxide Fuse Resistor Carbon Metal Oxide Metal Oxide Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Metal Oxide Carbon Carbon Metal Oxide
R9909 R9910 R9911 R9915 R9916 R9922
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AB AB AB AB AB AB AB AA AA AA AA AA
Part No.
★
VRD-RM2HD182J VRS-CY1JF221J VRD-RM2HD562J VRD-RA2BE103J VRS-CY1JF103J VRD-RA2BE331J
J J J J J J
Description 1.8k 220 5.6k 10k 10k 330
1/2W 1/16W 1/2W 1/8W 1/16W 1/8W
Carbon Metal Oxide Carbon Carbon Metal Oxide Carbon
Code AA AA AA AA AA AA
SWITCH SW701 QSW-F0042AJZZ
J Switch, REC TIP
AG
BALUNES FB202 FB203 FB1202 FB1203 FB1401 FB6101 FB6102
RBLN-0043CEZZ RBLN-0051TAZZ RBLN-0077TAZZ RBLN-0077TAZZ RBLN-0043CEZZ RBLN-0077TAZZ RBLN-0077TAZZ
J1201 J1202 J1204 PDA301 P201 P1201 P1202 P1203 P1204 P1205 P7001 P9601 SC301 SC601 SC602 SC1801 SC1802 SC7001 SC7002 W851 W852
QSOCD0445AJZZ QJAKG0093CEZZ QJAKG0065AJZZ PSLDM4540AJFW QPLGN0447REZZ QPLGN0278GEZZ QPLGZ1246GEZZ QPLGZ1246GEZZ QPLGZ1246GEZZ QPLGZ0746GEZZ QPLGZ0883GEZZ QPLGN1278GEZZ QSOCN0911REN1 QSOCN0604REN1 QSOCZ0293GEZZ QSOCN1595REZZ QSOCN1195REZZ QSOCZ0292GEZZ QSOCN0704REN1 LHLDZ1962AJ00 LHLDZ1962AJ00
J J J J J J J
Balun, BLN-0043CE Balun, BLN-0051TA Balun, BLN-0077TA Balun, BLN-0077TA Balun, BLN-0043CE Balun, BLN-0077TA Balun, BLN-0077TA
AB AC AB AB AB AB AB
MISCELLANEOUS PARTS
149
J J J J J J J J J J J J J J J J J J J J J
Socket Jack, Rear AV Jack, Rear AV Shield Plug, 4Pin Plug, 2Pin Plug, 12Pin Plug, 12Pin Plug, 12Pin Plug, 7Pin Plug, 8Pin Plug, 12Pin Socket, 9Pin Socket, 6pin Socket, 2Pin Socket, 17Pin Socket, 11Pin Socket, 2Pin Socket, 7Pin Holder Holder
AF AH AH AE AA AA AC AC AC AB AD AC AD AB AC AD AC AC AB AD AD
DV-NC55S/H DV-NC60H Ref. No.
Part No.
★
Description
Ref. No.
Code
AU AH AV AV AG
U U U U U
Packing Case(NC55S/H) Packing Case(NC60H) Wrapping Paper Packing Add. Packing Add.
CMECD0211HJV1 LX-BZ3189GEZZ NGERH1330AJZZ NGERH1341AJ00 LX-WZ1030GE00 LX-BZ3163GEFN QSW-M0066AJZZ DUNTK6062TEV1 RMOTV2019AJZZ NGERH1333AJZZ NGERR1021AJZZ MSPRC0244AJZZ NGERR1024AJZZ LX-HZ0083TAFF PCUSG0126AJZZ LX-HZ3117AJZZ QCNW-8552AJZZ QCNW-8553AJZZ MSLiP0014AJZZ LHLDZ2144AJZZ QCNW-8375AJZZ LHLDW1033CE00 RMOTM1097AJZZ NPLYM0001AJZZ QSW-B0011AJZZ NBLTK0068AJZZ NGERH1332AJZZ NGERP1016AJZZ LCHSM0314AJZZ LCRA-0002GEZZ LX-WZ0102GEFD PMAGS1001GEZZ GCOVA2164AJZZ LX-BZ3434AJFD
J J J J J J J – J J J J J J J J J J J J J J J J J J J J J J J J J J
Mecha Chassis Ass'y Guide Axis Pressing Biss Relay Gear1 Relay Gear2 Relay Gear Washer Motor Screw In SW Sled Motor PWB Unit Sled Motor Sled Motor Gear Double Action Rack Rack Spring Rack Rack Fixing Screw Insulator Traverse Fixing Screw Sled Wire Pickup Relay FFC Slide Rack Traverse Holder Loading Wire Nylon Band Loading Motor L Motor Pulley Loading Switch Loading Belt Pulley Gear Tray Pinion Base Chassis Disc Clamper York Washer Magnet Tray L Motor Fixing Screw
LBNDK1011AJZZ LBOSZ1007AJZZ LBOSZ1006AJZZ LCHSM0184AJZZ LHLDZ2016AJZZ LPOLM0070GEZZ LPOLM0064GEZZ MLEVF0518AJZZ
J J J J J J J J
510
MLEVF0519AJZZ
J
511 512 515 516 517 518 519 520 521 522 523 524 525 526 527 529 530
MLEVF0499AJZZ MLEVF0500GEZZ MLEVF0523AJZZ LANGF9620AJFW MLEVP0271AJZZ MLEVP0272AJZZ MLEVP0301AJZZ MLEVP0275AJZZ MLEVP0292AJZZ MLEVP0336AJZZ MLEVP0293AJZZ MLEVP0324AJZZ MLEVP0325AJZZ CLEVP0287AJZZ MSLiP0010AJZZ MSPRD0175AJFJ MSPRT0402AJFJ
J J J J J J J J J J J J J J J J J
531
MSPRT0403AJFJ
J
532 533 534 535-1 535-2 536 537 538 539 540 541 543 544 545 546 547 548 549 550 551 552 553 555 556 557 558 559 560 561 562 563 565 566
MSPRC0213AJFJ MSPRT0416AJFJ NBLTK0067AJ00 NDAiV1091AJ00 NDAiV1093AJ00 NGERH1293AJZZ NGERH1295AJ00 NGERH1294AJZZ NGERH1270AJZZ NGERH1271AJZZ NGERH1272AJZZ NGERH1299AJZZ NGERW1070AJZZ NGERW1066AJZZ NiDR-0018AJZZ NPLYV0162AJZZ NPLYV0163AJZZ NROLP0131GEZZ NSFTP0032AJZZ MSPRC0217AJFJ PREFL1011AJZZ QCNW-8345AJZZ QCNW-8021AJZZ QPWBF5243AJZZ QSOCN0696REZZ RHEDT0036AJZZ RHEDU0089GEZZ RMOTM1078GEZZ RMOTN2067GEZZ RMOTP1151GEZZ DDRMW0030TEXD QBRSK0041GEZZ XBPSD26P04500
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
567 568 569 570 571
PGiDC0056GEFW QPWBF5468AJZZ QPLGZ0292GEZZ MSPRC0228AJFJ MSPRC0224AJFJ
J J J J J
AG AB AG AG
— — — — —
MECHANISM PARTS (DVD PART) 401 401-1 401-2 401-3 401-4 401-5 401-6 401-7 401-8 401-9 401-10 401-11 401-12 401-13 409 410 413 418 419 420 421 422 423 424 425 426 427 428 429 431 432 433 434 435
501 502 504 505 506 507 508 509
AG
PACKING PARTS (NOT REPLACEMENT ITEM) SPAKC4950UMZZ SPAKC4890UMZZ SPAKP0002UMZZ SPAKX1144UMZZ SPAKX1146UMZZ
★
Description
Code
MECHANISM PARTS (VCR PART)
SUPPLIED ACCESSORIES QCNW-8077UMZZ U 21Pin Cable QCNW-7870UMZZ U RF Cable RRMCGA005WJSA U Remote Control Unit (NC55H/60H) RRMCGA012WJSA U Remote Control Unit (NC55S) TiNS-4058UMZZ U Operation Manual (NC55S) TiNS-4056UMZZ U Operation Manual (NC55H) TiNS-4054UMZZ U Operation Manual (NC60H) TiNS-4102UMZZ U Quick Start Guide (NC55H) TiNS-4059UMZZ U Quick Start Guide (NC55S) TiNS-4055UMZZ U Quick Start Guide (NC60H)
Part No.
BU AB AC AC AA AC AD — AM AB AC AB AC AA AD AC AF AF AD AD AD AA AM AB AE AD AC AC AL AD AB AF AH AB
150
Tension Band Ass’y AH Tension Arm boss AD Cassette Stay L AD Main Chassis Ass’y AQ Loading Motor Block AG Supply Pole Base Ass’y AK Take-up Pole Base Ass’y AM Take-up Loading AF Arm Ass’y Supply Loading AF Arm Ass’y Pinch Drive Lever Ass’y AG Pinch Roller Lever Ass’y AW Tension Arm Ass’y AH A/C Head Base AG Shifter Drive Lever AE Pinch Double Action Lever AD Reverse Guide Lever Ass’y AL Reverse Guide Drive Lever AD Slow Brake Lever AE Open Lever AD Clutch Lever AE Supply Main Brake Ass’y AF Take-up Main Brake Ass’y AF Auto Head Cleaner AG Shifter AH Reverse Guide Spring AE Loading Double Action AE Spring Pinch Double Action AD Spring Earth Spring AC Tension Spring AD Loading Belt AE Reel Disk1 AE Reel Disk2 AC Loading Connect Gear AD Master Cam AE Casecon Drive Gear AD Take-up Loading Gear AF Supply Loading Gear AD Pinch Drive Cam AE Reel Relay Gear AE Worm Gear AD Worm Wheel Gear AD Idler Wheel Ass’y AK Motor Pulley AD Limiter Pulley Ass’y AM Guide Roller AL Tension Pole Adjuster AB Guide Roller Spring AC Light Guide AE FFC for Drum Motor AH FFC for A/C Head AD A/C Head PWB AE Socket, 6 pin AB Full Erase Head AM A/C Head Ass’y AP Loading Motor AP Capstan D.D. Motor AY Drum Drive Motor AT Upper and Lower Drum Ass’y BH Drum Earth Brush AD Drum Drive Motor AB Mounting Screw (SW2.6P+5S) Drum Base AL PWB(LDG Motor) AE Socket(LDG Motor) AE Azimuth Spring AB Height Adjusting Spring AC
DV-NC55S/H DV-NC60H Ref. No.
Part No.
★
Description
Code
Ref. No.
XBPSD26P08000 XHPSD26P06WS0 LX-HZ3082GEZZ XJPSD26P060000 XHPSD30P08WS0
J J J J J
208 209 210 211 212 213 214
XRESJ30-06000 XWHJZ31-05052 XWHJZ31-03052 XWHJZ31-04052 XWHJZ31-06052 XWHJZ31-07052 PSPAP0009AJZZ
J J J J J J J
216 218
LX-WZ1041GE00 XBPSD30P06000
J J
219 220 221
LX-WZ1098GE00 LX-BZ3096GEFD XBPSD26P06000
J J J
222 223
XBPSD26P14000 XWHJZ31-08052
J J
Screw 2.6P+8S A/C Head C2.6P+6S(A/C) WSW 2.6+6 Screw, C2.6P+6S Screw, C3SP+8S (For Drum Base) E-Ring, E-3 Washer, W3.1 P-5.2-0.5 Washer, W3.1 P-5.2-0.3 Washer, W3.1 P-5.2-0.4 Washer, W3.1 P-5.2-0.6 Washer, W3.1 P-5.2-0.7 Reverse Guide Adjusting Nut CW 2.6-6-0.5 CAM Drum Base Mounting Screw SW3P+6S CW 2.6-4.7-0.5 RED Tilt Adjusting Screw Azimuth Adjusting Screw 2.6+6S Screw(A/C Head) Washer, W3.1 P-5.2-0.8
AA AA AD AA AA AA AC AC AC AC AC AB AA AA AB AA AA AA AC
CASSETTE HOUSING CONTROL PARTS 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317
CHLDX3081TEV2
J Cassette Housing Control Ass’y LANGF9592AJFW J Upper Plate LHLDX1028AJ00 J Frame (L) LHLDX1032AJ00 J Frame (R) LHLDX1030AJZZ J Holder (L) LHLDX1031AJZZ J Holder (R) MLEVF0469AJFW J Proof Lever (R) MLEVP0281AJ00 J Door Open Lever MSLiF0077AJFW J Slider MSPRD0151AJFJ J Proof Lever (R) Spring MSPRD0166AJFJ J Drive Gear (R) Spring MSPRP0175AJFJ J Cassette Spring MSPRT0381AJFJ J Double Action Spring NGERH1278AJZZ J Drive Gear L NGERH1309AJZZ J Drive Gear R NGERR1008AJ00 J Double Action Rack Gear NGERR3005AJFW J Drive Angle Gear NSFTD0041AJFD J Main Shaft
★
Description
Code
CABINET PARTS
SCREW, NUTS AND WASHERS 201 202-1 202-2 203 207
Part No.
AX AL AH AH AE AE AE AD AE AB AE AE AC AE AE AE AG AH
1 3 3 3 24 25 28 29 30 32 35 36 39 40 41 42 44 45 46 48 49 49 51 52 53 54 55 56 57 58 59
CCABA3167TEV1 CPNLC2990TEV1 CPNLC2990TEV2 CPNLC2980TEV1 LX-HZ3096GEZZ XEBSD30P12000 GCABB1251AJZZ GCOVA2208AJZZ GBDYU3141AJFW QEARP0460AJFW LANGF9653AJFW LANGF9654AJFW PGUMS0026AJZZ XEPSD30P14XS0 LX-HZ3087GEFN LX-HZ3100GEFF LHLDF1057CEZZ LX-HZ3099GEFD XHPSD30P06WS0 LHLDW1072GEZZ CDECQ2350TEV2 CDECQ2431TEV1 PSPAZ0470AJZZ XEBSF30P12000 PSPAZ0632AJZZ PSHEP0043AJZZ LHLDW1151AJZZ PSLDM4593AJFW LHLDW1006GEZZ LHLDP1198AJZZ LHLDP1200AJZZ
U U U U J J J U J J J J J J J J J J J J J J J J J J J J J J J
63 64 65 66
PSLDM4551UMFW PSPAZ0633AJZZ DUNTKB045TEV1 DUNTKB040TEV1
U J U U
66
DUNTKB084TEV1 U
67
DUNTKB047TEV1 U
67
DUNTKB087TEV1 U
68 69
DUNTK6054TE6E U DUNTKB042TEV1 U
69
DUNTKB086TEV1 U
70
DUNTKB041TEV1 U
70
DUNTKB085TEV1 U
71
DUNTKB043TEV1 U
71
DUNTKB043TEV2 U
72 73 74 å 75 å 75 76 77 78 79 80 81 82 83 84 85 86
151
QCNW-8021AJZZ QCNW-8345AJZZ QCNW-8553AJZZ QACCB5014UMZZ QACCV2009AJZZ QCNW-8600AJZZ QCNW-8601AJZZ QCNW-8602AJZZ QCNW-8603AJZZ QCNW-8604AJZZ QCNW-8605AJZZ QCNW-A224WJZZ QCNW-8607AJZZ QCNW-A225WJZZ QCNW-8609AJZZ QCNW-A227WJZZ
J J J U J J J J J J J J J J J J
Top Cabinet Ass'y KS Panel(NC55H) KS Panel(NC55S) KS Panel(NC60H) Screw Screw Panel Frame Rear Cover Plate (lower) Ground-Part Angle(DVD) DVD REINF. Angle Foot Rubber Screw Screw Screw Interface PWB Holder Screw Screw Wire Holder Tray Ass'y(NC55S/H) Tray Ass'y(NC60H) Spacer Screw Spacer Cover Holder DVD Shield(lower) Holder LED Holder DVD LED Holder (NC55S/H) H/A Shield(Top) Spacer AV PWB Unit Interface PWB Unit (NC55S/H) Interface PWB Unit (NC60H) Power PWB Unit (NC55S/H) Power PWB Unit (NC60H) DVD Main PWB Unit VCR Display PWB Unit (NC55S/H) VCR Display PWB Unit (NC60H) DVD Display PWB Unit (NC55S/H) DVD Display PWB Unit (NC60H) VCR Main PWB Unit (NC55H/60H) VCR Main PWB Unit (NC55S) Connecting Cord Connecting Cord Connecting Cord AC Cord(NC55H/60H) AC Cord(NC55S) Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord
AR AX AX AX AB AA AQ AG AQ AC AM AC AB AB AB AA AB AB AA AA AH AK AC AA AB AB AC AE AA AB AD AB AC — — — — — — — — — — — — AD AH AF AQ AM AD AE AC AC AC AE AE AG AD AF AC
DV-NC55S/H DV-NC60H Ref. No. 87 88 90 91 93 94 95 96 97 98 99
Part No.
★
XHPSF30P10WS0 PSPAZ0641AJZZ PSLDM9385AJZZ PSLDM4591AJFW TLABS0417AJZZ GCOVA3065AJZZ QCNW-A226WJZZ QCNW-A256WJZZ DUNTKB046TEV1 TLABZ1748UMZZ QCNW-8022AJZZ
J J J J J U U J U U J
Description Screw Spacer Spacer Shild Plate(NC55S/H) Laser Caution Label Rear Panel Connecting Cord Connecting Cord Terminal PWB Unit Rear Cover Label FFC For Drum Motor
Ref. No.
Code AA AB AE AF AC AG AB AH — AF AD
FRONT PANEL PARTS DV-NC55S/H 601 601 601-1 601-2 601-3 601-4 601-5 601-6 601-7 601-7 601-9 601-10 601-12
CPNLC2990TEV1 CPNLC2990TEV2 HDECQ2351AJSB HDECQ2401AJSA HiNDP2238AJSB HiNDP2172AJSB JBTN-3132AJSA JBTN-3121AJSB CDECQ2316TEV7 CDECQ2316TEV5 MSPRD0103AJFJ XEBSD20P06000 HDECQ1993AJZZ
601 601-1 601-2 601-3 601-4 601-5 601-6 601-7 601-8 601-9 601-10
CPNLC2980TEV1 HiNDP2180AJSA HiNDP2183AJSA HDECQ2434AJZZ HDECQ2430AJSA JBTN-3149AJSA JBTN-3150AJSA JBTN-3151AJSA HDECQ2432AJSA MSPRD0103AJFJ HDECQ1993AJZZ
U U J J U J J J U U J J J
Front Panel Ass'y(NC55H) Front Panel Ass'y(NC55S) Decoration Plate(Left) Decoration Plate(Right) Indicator(Left) Indicator(Right) Button(Left) Button(Right) C Cassette Flap(NC55H) C Cassette Flap(NC55S) Cassette Flap Spring Screw LED Cover
AX AX AF AL AD AF AG AG AK AK AB AA AF
DV-NC60H U U U U U U U U U J J
Front Panel Ass'y VCR Indicator DVD Indicator DVD/VCR Decoration Window Decoration VCR Mode Button Channel Rec Button DVD Mode Button Cassette Flap Dec. Cassette Flap Spring LED Cover
AX AD AD AG AG AC AC AC AG AB AF
152
Part No.
★
Description
Code
DV-NC55S/H DV-NC60H
MECHANISM EXPLODED VIEW (DVD Code PART) Ref. No. Part No. ★ Description
Ref. No.
★
Part No.
Description
Code
Dry Coating
H
Dry Coating
Dry Coating 434
G
429 432
F
Dry Coating
433 431 Grease 435
Grease
428
E
427 425
426
401-11 401-13
420
401-10
424
D Grease
Grease
401-4
401-12 401-3 401-2
422
423
409
421
C Grease 419
418
401-5
410
409 409
B
å Caution When touching the pickup, wear an earth band to prevent breakage by static electricity.
401-9 401
410 401-8
401-1
413 409
A 401-6
1
2
401-7
3
4
153
5
6
DV-NC55S/H DV-NC60H
MECHANISM Ref. No. Part No.
EXPLODED VIEW (VCR PART)Ref. No. ★ Description Code
★
Part No.
Description
Code
566 566
H
553 566
222 202
220
566 570
526
557
565
555
221
562
559
G 563
556
201
202-1
202-2
207 207
516
550 571
F
501
549
567
522
551 218
549
515 558 533
508
551
E
552
502
524
531
532
525 511
214 512
504 507
519 518 520 203
529
D 535-1 535-2
546
C
505 209 210 211 212 213 223
216 541 543
561
543 523
509 521
510
539 530
530
B
536 538
534
517
540 537 548
506
545
208 544
527
547 560
219
568
A 569
1
2
3
4
154
5
6
DV-NC55S/H DV-NC60H
CASSETTE CONTROL Ref. No. Part No.HOUSING ★ Description
EXPLODED Code Ref.VIEW No.
★
Part No.
Description
Code
H
300
G
301
F
304 302 311 311
E
305
306
308
309 313
D
310 317 C
303 314 312 B
307
315 316
A
1
2
3
4
155
5
6
DV-NC55S/H DV-NC60H
CABINET VIEW Ref. No. Part EXPLODED No. ★ Description 46
Ref. No.
Code
87
51
24
H
★
Part No.
Description
Code
Y 1
87 94
B
52 87
H
H
J
87
A
40
C
95
N
25
M
E
D
X 87
81
73
86
AA
41 Z
O
52
V
J
87 40
24
97
72
G
A
65
40
M
99
75
84
N 46
Q R
98
29
E
U 76
U
C L
25
79
W
28
35
I
I
25
55 48
88
R
A
83
W 68
Y A
L
Z
30
80
P 59
C
I
54
32
88 91
X 74
G
67
G
K
F 55
F
A
69
44
G
46
32
H
D
S
53 64
D 78
25
46
85 57
71
90
O
96
K
66
V
P
63
E
93
36
Y
G
F
Y
25
B
39
Q
T
45
3 58
Y
70 42
82
AA
S
88 77
H
49
88
K 69 25 L
B
88
A
80
DV-NC55S/H
T
56
88 58
T 58
70
H 49
A
3
DV-NC60H
1
2
3
4
156
5
6
DV-NC55S/H DV-NC60H
FRONTPart PANEL Ref. No. No.
EXPLODED VIEW(DV-NC55S/H) ★ Description Code Ref. No.
★
Part No.
Description
Code
H
601 G
601-10
601-7
F
601-3
601-9
601-5
601-1
E
601-10 601-6
D
601-4 601-12 601-2 C
B
A
1
2
3
4
157
5
6
DV-NC55S/H DV-NC60H
FRONTPart PANEL Ref. No. No.
EXPLODED VIEW(DV-NC60H) Ref. No. ★ Description Code
Part No.
★
Description
Code
H
601 G
601-9
601-8 601-5 F
601-6
E
601-7 601-10 601-1
D
601-3
601-2
601-4 C
B
A
1
2
3
4
158
5
6
DV-NC55S/H DV-NC60H Ref.PACKING No. Part No. ★ SET Description 17. OF THE
Code
Ref. No.
Part No.
★
Description
Code
No.5 No.4 No.3 ★No.7
No.1, 2
★No.9
★No.8
★No.6
ACCESSORIES
PACKING PARTS (NOT REPLACEMENT ITEM)
No.
Model
1
– Common parts –
QCNW-8077UMZZ 21Pin Cable
2
– Common parts –
QCNW-7870UMZZ RF Cable
3
4
5
Parts Code
Description
Remarks
No. 6
Model
Parts Code
Description
Remarks
NC55S/H
SPAKC4950UMZZ
Packing Case
★
NC60H
SPAKC4890UMZZ
Packing Case
★
NC55H/60H
RRMCGA005WJSA Remote Control Unit
7
– Common parts –
SPAKP0002UMZZ
Wrapping Paper
★
NC55S
RRMCGA012WJSA Remote Control Unit
8
– Common parts –
SPAKX1144UMZZ
Packing Add.
★
NC55S
TiNS-4058UMZZ
Operation Manual
9
– Common parts –
SPAKX1146UMZZ
Packing Add.
★
NC55H
TiNS-4056UMZZ
Operation Manual
NC60H
TiNS-4054UMZZ
Operation Manual
NC55H
TiNS-4102UMZZ
Quick Start Guide
NC55S
TiNS-4059UMZZ
Quick Start Guide
NC60H
TiNS-4055UMZZ
Quick Start Guide
MARK ★ Not Replacement Item
159
DV-NC55S/H DV-NC60H Ref. No.
Part No.
★
Description
Ref. No.
Code
Part No.
★
Description
Code
COPYRIGHT © 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
D Japan P SUKM TQ1231-S Nov. 2001 Printed in JAPAN SA. DS
160
