(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including ... interference to radio communications.
General Applications: The Qolsys Image Sensor Module features the ATXMEGA123D3 microcontroller and AT86RF212 transceiver, providing Zigbee air interface to, and compatibility with Alarm.com’s 900 MHz Image Sensors. OEMs that integrate this module will gain control to the image sensor, allowing rule-based monitoring and camera peak-ins. Installation and Operation: It is recommended to secure the module to a large ground plane using the mounting hole and header pins. Do not place any large pieces of metal around or near the antenna, as it will inhibit performance.
The Qolsys Image Sensor Module operates around 915 MHz with an output power up to +10dBm. Data and protocol specifications are beyond the scope of this document. Please contact Qolsys for the technical specifications. FCC Compliance: FCCID: 2AAJXQS-IS This equipment complies with radiation exposure limits set forth for uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. IC Compliance: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux normes d’exemption de licence RSS d’Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement, votre corps, et d’autres antennes ou transmetteurs.
CAN ICES-3 (B)/NMB-3(B) Warranty Information: IMPORTANT! Changes or modifications not expressly approved by Qolsys Inc. could void the user’s authority to operate the equipment, as well as warranty for the product.
Overview. The MN39470PT is a type-1/2.72 2.11M-pixel square-pixel CCD image sensor. This CCD has achieved excellent color reproduction by adopting RGB ...
The MW39580AE is a type-2/3 2.2M-Pixel IT-CCD image sensor that supports the interlace 1080i HDTV ... 5.0μm(H)×5.0μm(V). 120ｍV (typ.) 32-pin ceramic ...
pixel signals separately in one vertical scanning period Square pixel is VGA capture system. Adopting RGB Bayer arrangement in color filter array provides.
The TC254P is a frame-transfer charge-coupled device (CCD) designed for use in ... Specific guidelines for handling devices of this type are contained in the .... amplifier are located a short distance away from the edge of the storage area; .... Gam
(pixels). Each pixel is 13.75 µm (horizontal) by 16.00 µm (vertical). .... High level. 1.5. 2. 2.5. V. Input voltage, VIâ . SRG. Low level. â11. â 10. â 9. V. High level. 4.
Burn-In, Residual Imaging, Image. Distortion ... testing of all parameters. ..... For this test, the antiblooming gate must be biased at the intermediate level. 4.
Burn-in, Residual Imaging, Image. Distortion ... testing of all parameters. ..... For this test, the antiblooming gate must be biased at the intermediate level. 4.
The TC277 is a frame-transfer charge-coupled device (CCD) image sensor designed ... Specific guidelines for handling devices of this type are contained in the .... detection nodes and the corresponding amplifiers are located some distance .... Gamma
Correlated Double Sampling (CDS) .... There are 22 columns at the left edge of the image-sensing area that are shielded from incident light; these elements ...
such as Sensitivity, Exposure Latitude, Resolving Power, Color Fidelity, Frame Rate, and one we might call âPersonality.â This paper will use such a.
The TC213 is a frame-transfer charge-coupled device (CCD) image sensor that ... Specific guidelines for handling devices of this type are contained in the .... contains 12 dummy elements that are used to span the distance between the serial ..... Gam
The independent addressing of each field memory provides flexibility ... of off-chip double correlated-clamp sample-and-hold amplifiers for removing KTC noise.
Burn-In, Residual Imaging, Image. Distortion, Image Lag ... testing of all parameters. DUAL-IN-LINE ..... The test is performed in the dark using an electrical input ...
In designing the sensor and electronics for our Origin® digital cinematography camera ... It should be noted that not all of a device's dynamic range is linear. Above and .... mainstream logic and memory circuits) mean they are relatively ... imager
Honeywell International Inc. Honeywell Limited-Honeywell Limitée. 1985 Douglas Drive North. 35 Dynamic Drive. Golden Valley, MN 55422. Toronto, Ontario ...
a wide range of applications, including surveillance and HD video. Table 1: ...... row time (in clocks) is programmable through R0x300C. ...... R0x3102. For the MT9M034 this target luma has a default value of 0x0800 or about half scale.
May 22, 2002 - TV8202B CIF/QCIF CMOS sensor with digital YUV output. Outline Spec ... On-chip digital signal processing. â¢. Real-time ... Digital still camera.
Figure 2. 5. Run the cable through the printer as show on picture 3. The connector will be connected to the DIMM (on. 4200-4300) or CompactFlash (on ...
