Installation Guide Bluetooth LE Radio Module - UserManual.wiki
Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is.
This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for Class B Digital Devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the product manuals, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to do one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced RF service technician for help.
The end product must be labeled, in a visible area, with the following: Contains FCC ID: I28MD-ZBRBLE
Modification Warning The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with fully shielded communication cables.
RF Exposure Statement This transmitter complies with FCC radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multitransmitter product procedures.
Canadian DOC Compliance Statement Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003.
Industry Canada (IC) Warning Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) This device may not cause interference., 2) This device must accept any interference, including interference that may cause undesired operation of the device. The end product must be labeled, in a visible area, with the following: Contains IC: 3798B-ZBRBLE
Approved Antenna information Only Zebra approved antennas are allowed and cannot be user replaceable. Antenna Type: Chip: Gain: 1dBi (2.4G);
General The Bluetooth Low Energy radio module has been certified as a Full Modular. Additional evaluation is required for use in all host devices. The following describes the installation procedures for the various hosts in which the module has been evaluated.
Installation Instructions for Zebra printers The Bluetooth Low Energy radio module is not intended for OEM Integrators or end users. it can only be installed at the grantee manufacturing facility.
undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when th
Networking (LAN, Ad hoc, ...) 18. Rendering (Printing, Speaker, ...) .... attempt to connect to the one reporting the lowest load. 4. 3. 2. Minor Device Class bit no of ...
AT command mode, user can configure the module and send control .... Example: Set serial port parameters to 115200, 2 bits stop bit, and even ... AT+MPIO?
Oct 5, 2007 - Any part or whole of products or operation description shall not be copied, ..... Wireless Communication for Short Distance with Low Power.
Almacenamiento y sou. Nunca exponga el dispositivo a la humedad, polvo, aceite o humo. Nunca ponga el dispositivo en contenedores inestables, ya que le podría causar daños. Mantenga este equipo alejado de temperaturas extremas. Nunca roce este tipo d
The Pairing Indicator will flash blue slowly. When pairing, remain within 3 feet of the unit. 2. Press the Source/Pair knob. The Pairing Indicator will flash blue quickly. 3. Using the native controls on your. Bluetooth device, select the “ISB313CW”
The following information must be indicated on the host device of this module;. [for FCC]. Contains FCC ID: RYYEYSGCC. This device complies with part 15 of ...
Figure 1-2 shows a block diagram of the RN52 with Bluetooth audio and .... After pairing with the device is successful, the module can now connect to the device.
General Items. Scope. This specification (âSpecificationâ) applies to the hybrid IC âRUITZ0004MPZZâ, a Bluetooth® 4.2 low energy module (âProductâ). 1.
Regulatory Information. USA-Federal Communications ... for compliance could void the user's authority to operate the equipment. Labeling. System integrators ...
vous permettent d'utiliser les valeurs d'un accéléromètre comme conditions. ... l'accéléromètre (Accelerometer Settings) de l'application plutôt que dans la boite ...
5.1.2. Exemple de programme utilisant l'application de contrôle . ... Sélectionner « Bluetooth : ID » comme condition vous permet de choisir parmi un certain.
System integrators must include the FCC ID on the label of the end product as ... If an antenna with higher gain or new antenna type is used with this module,.
NÃO instale se o produto tiver algum dano visÃvel. ⢠Se a umidade ou condensação forem evidentes, deixe o produto secar completamente antes da instalação.
PDF Subject: Le Guide Du Wifi Et Du Bluetooth Its strongly recommended to start read the Intro section, next on the Quick Discussion and find out all the topic ...
Multiple Configuration Options o Single-Chip Configuration, Allowing. Applications to Run on CC2541 o Network Processor Interface for. Applications ... Do you need help with your host board? LS Research Design Services will be happy to develop custom
fils du ventilateur seront toujours attachés à la carte mère car il est fixé de façon permanente.. Étape 8. En utilisant une tête Philips (PH0) tournevis, dévisser ...
rating plate is located on the bottom of the control panel, at the far right, .... SIDE VIEW. *Without .... parte inferior del montaje del panel de control, en el extremo.
Los números de productos seguidos de ... without notice, as specified in the Price Book. ..... Debido a la naturaleza de las instalaciones bajo cubierta, Kohler.