(b) Lift up the caliper and suspend it securely. HINT: ... REMOVE 2 PAD SUPPORT PLATES. NOTICE: The support plates can be used again provided that they.
REPLACEMENT 1. REMOVE FRONT WHEEL 2. INSPECT PAD LINING THICKNESS Check the pad thickness through the caliper inspection hole and replace the pads if they are not within the specification. Minimum thickness: 1.0 mm (0.039 in.)
F07789
3. (a)
F07790
F08580
LIFT UP CALIPER Hold the sliding pin on the bottom and loosen the installation bolt, and remove the installation bolt. Lift up the caliper and suspend it securely.
(b) HINT: Do not disconnect the flexible hose from the caliper. 4. REMOVE BRAKE PADS WITH ANTI-SQUEAL SHIMS 5. REMOVE 2 PAD SUPPORT PLATES NOTICE: The support plates can be used again provided that they have sufficient rebound, no deformation, cracks or wear, and have had all rust, dirt and foreign particles cleaned off. 6. CHECK DISC THICKNESS AND RUNOUT (See page BR-24 ) 7. INSTALL 2 PAD SUPPORT PLATES 8. INSTALL NEW PADS NOTICE: When replacing worn pads, the anti-squeal shims and pad wear indicator plates must be replaced together with the pads. (a) Apply disc brake grease to the anti-squeal shims (See page BR-21 ). (b) Install the 2 anti-squeal shims on the outer pad. (c) Install the 2 anti-squeal shims on the inner pad. (d) Install the inner pad with the pad wear indicator plate facing upward. (e) Install the outer pad. NOTICE: There should be no oil or grease adhering to the friction surfaces of the pads or the disc. 9. INSTALL CALIPER (a) Draw out a small amount of brake fluid from the reservoir. (b) Press in the piston with a hammer handle or similar implement. HINT: If the piston is difficult to push in, loosen the bleeder plug and push in the piston while letting some brake fluid escape. (c) Install the caliper. (d) Hold the sliding pin and install the installation bolt. Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
2002 ECHO (RM884U)
Author:
Date:
1036
BR-20 BRAKE
10. 11.
-
FRONT BRAKE PAD
INSTALL FRONT WHEEL CHECK THAT FLUID LEVEL IS AT MAX LINE
(d) Repeat (b) and (c) 3 or 4 times. 3. BLEED BRAKE LINE. (a) Connect the vinyl tube to the caliper or wheel cylinder. (b) Depress the brake pedal several times, ...
INSTALLATION. 1. INSTALL BRAKE BOOSTER. (a) Install the booster and a new gasket. (b) Install and and torque the booster installation nuts. Torque: 13 N·m ...
Mar 25, 2005 - you get the proper sequence from the manual) without rotors and see if the .... clean the buttons completely so that they are free od any debris / grime. .... rotors, please ask the manufacturer (not the zit-faced kid at the dealer.
(b) In case of not using TOYOTA hand-held tester: Check the DTC. (1) Using SST, connect terminals Tc and CG of DLC3. SST. 09843-18040. (2) Turn the ...
The hub bearing could be damaged if it is subjected to the vehicle weight, such as when moving the ve- hicle with the drive shaft removed. Therefore, if it is ...
Jan 21, 2002 - variation will never change, though pad material may get deposited on one ... trained, experienced technical mechanic, with proper equipment, install ... Please believe us, it will be better to read and understand this ENTIRE Installat
bureaux). • Bâtiments passifs ou très performants (BBC -30%). • Mixité fonctionnelle, sociale et générationnelle. • Une maîtrise d'usage associée au projet dès la ...
rangement shown in Fig. 2. This system was based on using a conversion of the existing pedals. By using a ... and the last one looked like the answer. In essence, ... in Figure 3. The ribbed rubber pads shown were part of a bicycle pedal.
it bottoms out and then pull it back quickly b. â Repeat this step until the inner tube can be pulled out from the outer tube. EC553311. Damper rod. 1. Remove:.
I ended up with a simple, easy to build, and inexpensive ... Drill four holes for the 3/8-inch bolts through the ... Remove the top plate and round off the front edge ...
2413 Ives Lane. Redondo Beach. CA 90278. 1 HE FOLLOWING INFORMATION was first published in the January 1962 edition of Sport Aviation. Since that time ...
