(b) In case of not using TOYOTA hand-held tester: Check the DTC. (1) Using SST, connect terminals Tc and CG of DLC3. SST. 09843-18040. (2) Turn the ...
DIAGNOSIS SYSTEM Check the indicator. When the ignition switch is turned ON, check that the ABS warning light goes on for approx. 3 seconds.
HINT: If the indicator check result is not normal, proceed to troubleshooting for the ABS warning light circuit (See page DI-231 ). F10030
(b)
CG
DLC3
Tc
HINT: A04550
Normal Code 2 sec.
In case of not using TOYOTA hand-held tester: Check the DTC. (1) Using SST, connect terminals Tc and CG of DLC3. SST 09843-18040 (2) Turn the ignition switch ON. (3) Read the DTC from the ABS warning light on the combination meter.
0.25 sec. 0.25 sec.
ON
OFF
If no code appears, inspect the diagnostic circuit or ABS warning light circuit (See page DI-234 or DI-231 ). As an example, the blinking patterns for normal code and codes 11 are shown on the left. (4) Codes are explained in the code table on page DI-204 . (5) After completing the check, disconnect terminals Tc and CG, and turn off the ignition switch. Even if 2 or more malfunctions are detected, the lowest numbered DTC will be displayed.
Code 11 0.5 sec. 1.5 sec. 4 sec. ON OFF
Code11 F08905
(c) TOYOTA Hand-held Tester
DLC3
D08002
In case of using TOYOTA hand-held tester: Check the DTC. (1) Hook up the TOYOTA hand- held tester to the DLC3. (2) Turn the ignition switch ON. (3) Read the DTC by following the prompts on the tester screen. Please refer to the TOYOTA hand-held tester operator’s manual for further details.
2002 ECHO (RM884U)
Author:
Date:
371
DI-202 DIAGNOSTICS
In case of not using TOYOTA hand-held tester: Clear the DTC. (1) Using SST, connect terminals Tc and CG of DLC3. SST 09843-18040 (2) Turn the ignition switch ON. (3) Clear the DTC stored in ECU by depressing the brake pedal 8 or more times within 5 seconds. (4) Check that the warning light shows the normal code. (5) Remove the SST from the terminals of DLC3. SST 09843-18040
(e)
In case of using TOYOTA hand-held tester: Clear the DTC. (1) Hook up the TOYOTA hand- held tester to the DLC3. (2) Turn the ignition switch ON. (3) Operate the TOYOTA hand-held tester to erase code (See TOYOTA hand-held tester operator’s manual.).
2. (a) (b) (c)
SPEED SENSOR SIGNAL CHECK (TEST MODE) Hook up the TOYOTA hand-held tester to the DLC3. Start the engine. Drive vehicle faster than 45 km/h (28 mph) for several seconds.
TOYOTA Hand-held Tester
D08002
TOYOTA Hand-held Tester
DLC3
ANTI-LOCK BRAKE SYSTEM
(d)
BR3890
DLC3
-
D08002
HINT: There is a case that the sensor check is not completed if the vehicle has its wheels spined or its steering wheel steered during this check. (d) Read the DTC, from TOYOTA hand-held tester screen. HINT: See the list of DTC shown on the next page. Please refer to the TOYOTA hand-held tester operator’s manual for further details.
2002 ECHO (RM884U)
Author:
Date:
372
DI-203 DIAGNOSTICS
-
ANTI-LOCK BRAKE SYSTEM
DTC of speed sensor check function: Code No.
Diagnosis
Trouble Area
C1271 / 71
Low output voltage of right front speed sensor
Right front speed sensor Right front speed sensor rotor Sensor installation
C1272 / 72
Low output voltage of left front speed sensor
Left front speed sensor Left front speed sensor rotor Sensor installation
C1273 / 73
Low output voltage of right rear speed sensor
Right rear speed sensor Right rear speed sensor rotor Sensor installation
C1274 / 74
Low output voltage of left rear speed sensor
Left rear speed sensor Left rear speed sensor rotor Sensor installation
C1275 / 75
Abnormal change in output voltage of right front speed sensor
Right front speed sensor rotor
C1276 / 76
Abnormal change in output voltage of left front speed sensor
Left front speed sensor rotor
C1277 / 77
Abnormal change in output voltage of right rear speed sensor
Right rear speed sensor rotor
C1278 / 78
Abnormal change in output voltage of left rear speed sensor
(d) Repeat (b) and (c) 3 or 4 times. 3. BLEED BRAKE LINE. (a) Connect the vinyl tube to the caliper or wheel cylinder. (b) Depress the brake pedal several times, ...
INSTALLATION. 1. INSTALL BRAKE BOOSTER. (a) Install the booster and a new gasket. (b) Install and and torque the booster installation nuts. Torque: 13 N·m ...
(b) Lift up the caliper and suspend it securely. HINT: ... REMOVE 2 PAD SUPPORT PLATES. NOTICE: The support plates can be used again provided that they.
This opens the way for a variety of applications ranging from distance ... the polynomial representation of the calibration curve, stored in the application program.
Mar 25, 2005 - you get the proper sequence from the manual) without rotors and see if the .... clean the buttons completely so that they are free od any debris / grime. .... rotors, please ask the manufacturer (not the zit-faced kid at the dealer.
rangement shown in Fig. 2. This system was based on using a conversion of the existing pedals. By using a ... and the last one looked like the answer. In essence, ... in Figure 3. The ribbed rubber pads shown were part of a bicycle pedal.
I ended up with a simple, easy to build, and inexpensive ... Drill four holes for the 3/8-inch bolts through the ... Remove the top plate and round off the front edge ...
2413 Ives Lane. Redondo Beach. CA 90278. 1 HE FOLLOWING INFORMATION was first published in the January 1962 edition of Sport Aviation. Since that time ...
INSPECTION. 1. Visually inspect the caliper for corrosion, leaking hydraulic fluid, cracks or visible damage. 2. Check back plate attachment bolts to insure that ...
Remove the clevis in (C) from the master cylinder oper- ating lever (E). 3. Turn the pull rod (D) to increase the length until the clevis pin (C) just enters the rod ...
move some of the pressure lines around to be able to fit your vacuum booster where it's ... the pressure line that goes down from the power steering pump.
The handbrake lever has been discontinued and replaced by a button. ... vehicle is held automatically each time it is brought .... control unit can calculate the optimum release point of the parking brake for purposes .... parking brake control unit
