(c) Using a dial indicator, check the backlash near the center of the axle hub. Maximum: 0.05 mm (0.0020 in.) If the backlash exceeds the maximum, replace the ...
CHECK BEARING BACKLASH AND AXLE HUB DEVIATION Remove the 2 bolts, brake caliper and disc. Support the brake caliper securely.
(a) (b)
F07299
Backlash:
(c)
Deviation:
R14731
SST F07286
Using a dial indicator, check the backlash near the center of the axle hub. Maximum: 0.05 mm (0.0020 in.) If the backlash exceeds the maximum, replace the bearing. (d) Using a dial indicator, check the deviation at the surface of the axle hub outside the hub bolt. Maximum: 0.05 mm (0.0020 in.) If the deviation exceeds the maximum, replace the axle hub. (e) Install the disc, brake caliper and 2 bolts. Torque: 88 N·m (900 kgf·cm, 65 ft·lbf) 3. REMOVE DRIVE SHAFT LOCK NUT (a) Using SST and a hammer, unstake the staked part of the lock nut. SST 09930-00010 (b) While applying the brakes, remove the lock nut. (c) Remove the 2 bolts, brake caliper and disc. (d) Support the brake caliper securely. 4. w/ ABS: DISCONNECT ABS SPEED SENSOR Remove the bolt and disconnect the ABS speed sensor. 5. DISCONNECT STEERING KNUCKLE FROM LOWER SUSPENSION ARM (a) Remove the clip and nut.
2002 ECHO (RM884U)
Author:
Date:
970
SA-1 1 SUSPENSION AND AXLE
(b)
6. (a)
SST
-
FRONT AXLE HUB
Using SST, disconnect the steering knuckle. SST 09628-0001 1 (09628-00030, 09628-00040, 09628-00050) DISCONNECT TIE ROD END FROM STEERING KNUCKLE Remove the cotter pin and nut.
F08764
(b)
Using SST, disconnect the tie rod end. SST 09628-6201 1
SST
F07373
7. REMOVE STEERING KNUCKLE WITH AXLE HUB Remove the 2 nuts, bolts and steering knuckle with the axle hub from the shock absorber. NOTICE: Be careful not to damage the boot and ABS speed sensor rotor.
«Escort 1991/1996 Table of Contents». «Group 14: Front Axle, Suspension and Driveshafts». «Section 14-02: Front Axle and Driveshafts». «REMOVAL AND ...
Vehicle with 1,8 Endura-DE (TC) engine only. Note: The intermediate shaft extension was omitted after 1/97. µ. 4. Remove the right-hand intermediate driveshaft ...
Do not damage the suspension support stud bolts. (e) Remove the suspension support, dust seal, spring upper seat, upper insulator, spring bumper and coil ...
The hub bearing could be damaged if it is subjected to the vehicle weight, such as when moving the ve- hicle with the drive shaft removed. Therefore, if it is ...
I used a slitting saw in the vertical mill to split a 3-inch length of 11/2-inch OD 4130 tubing into two saddles. Note how I used finger ... Please tell them you saw their ad in KITPLANES® Magazine. .... INTRODUCING THE LEGAL EAGLE XL.
This pattern matches axle part numbers 5030 and 5031. This pattern matches axle part numbers 5010, 5011, 5012,. 5013, 5014, 5014-1, 5015,. 5018, 5026 and ...
available as a new part. Gp 4 axles with ... The Atlas is an adapted version of the 3 litre Capri axle, and is 1" wider than the English ... prevent the back of the wheel studs on the hub carrier rubbing against the new axle ... studs. Parts laid out
it bottoms out and then pull it back quickly b. â Repeat this step until the inner tube can be pulled out from the outer tube. EC553311. Damper rod. 1. Remove:.
3. Lift engine into position (in boat), using an over- head hoist. 4. Align rear engine mounts with inner transom plate mounts while simultaneously aligning ex-.
électroniques soutenu par le Réseau canadien de recherches sur ..... Ce qui a commencé principalement en Alberta s'est dernièrement étendu plus largement.
