Vehicle with 1,8 Endura-DE (TC) engine only. Note: The intermediate shaft extension was omitted after 1/97. µ. 4. Remove the right-hand intermediate driveshaft ...
«Escort 1991/1996 Table of Contents» «Group 14: Front Axle, Suspension and Driveshafts» «Section 14-02: Front Axle and Driveshafts» «REMOVAL AND INSTALLATION»
Seal - Inner - Right-hand Front Axle Driveshaft - Renew (14 304 0) Special Tools
16-018Driveshaft oil seal installer
16-087Driveshaft remover
21-051Oil seal remover Proprietary Tools ⁄ƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒƒø ≥ Auxiliary plugs
Hold the piston rod using an Allen key. 1. Undo the right-hand suspension strut nut five turns. 2.
Raise the vehicle and remove the engine undershield.
3.
Detach the right-hand lower suspension arm from the spindle carrier.
Vehicle with 1,8 Endura-DE (TC) engine only.
µ
Note: The intermediate shaft extension was omitted after 1/97. 4. Remove the right-hand intermediate driveshaft bearing. z z z
Remove the left-hand front axle driveshaft from the transmission in accordance with «Operation No. 14 303 0». Free the right-hand front axle driveshaft from the transmission by tapping it lightly from the other side, as described in step Pull out the right-hand front axle driveshaft, swivel it forwards and tie it up.
CAUTION: The inner joint must not be bent at more than 18º, and the outer joint at not more than 45º. Note: If the right-hand front axle driveshaft is difficult to remove, see step
µ
Note: Watch out for escaping oil. 5. Release the right-hand front axle driveshaft from the transmission. Pull out the right-hand front axle driveshaft, swivel it forwards and tie it up.
Note: Only if the right-hand front axle driveshaft is difficult to remove.
µ
Note: Watch out for escaping oil. 6. Remove the right-hand front axle driveshaft from the transmission. z z z z
Remove the left-hand front axle driveshaft from the transmission in accordance with «Operation No. 14 303 0». Release the right-hand front axle driveshaft from the transmission by tapping it lightly from the other side. Remove the special tool and seal off the transmission using assembly plugs. Pull out the right-hand front axle driveshaft, swivel it forwards and tie it up.
µ
7.
Remove the right-hand front axle driveshaft oil seal.
Install 8.
General notes. Renew all the snap rings, self-locking nuts and split pins.
µ
9.
Install the right-hand front axle driveshaft oil seal.
CAUTION: Check the front axle driveshaft for traces of a groove caused by the oil seal.
CAUTION: The inner joint must not be bent at more than 18º, and the outer joint at not more than 45º. CAUTION: When installing the front axle driveshaft use the locating sleeve (supplied with every new seal) to protect the oil seal.
µ
Note: Make sure the snap ring clips firmly in place. 10. Install the right-hand front axle driveshaft together with a new snap ring in the transmission.
Vehicles with 1,8 Endura-DE (TC) engines only.
µ
Note: The intermediate shaft extension was omitted after 1/97. 11. Install the right-hand intermediate driveshaft bearing. 12.
µ
If removed, install the left-hand axle driveshaft as described in «Operation No. 14 303 0».
CAUTION: Top up the oil to the maximum mark before commencing the test drive if a CTX automatic transmission is fitted. 13. Fill up with transmission fluid. z
iB5 manual transmission = Ford Transmission Fluid (WSD-M2C200-C) 10 to 15 mm below the
z z z
µ
bottom edge of the filler/check bore. B5 manual transmission = Ford High Pressure Transmission Fluid (SQM-2C9008-A) 5 to 10 mm below the bottom edge of the oil filler/check bore. MTX 75 manual transmission = Ford Transmission Fluid (ESD-M2C186-A) to the lower edge of the oil filler/check bore. CTX automatic transmission, procedure as per section 17-01, Description and function.
14.
Attach the right-hand lower suspension arm to the spindle carrier.
«Escort 1991/1996 Table of Contents». «Group 14: Front Axle, Suspension and Driveshafts». «Section 14-02: Front Axle and Driveshafts». «REMOVAL AND ...
(c) Using a dial indicator, check the backlash near the center of the axle hub. Maximum: 0.05 mm (0.0020 in.) If the backlash exceeds the maximum, replace the ...
Do not damage the suspension support stud bolts. (e) Remove the suspension support, dust seal, spring upper seat, upper insulator, spring bumper and coil ...
I used a slitting saw in the vertical mill to split a 3-inch length of 11/2-inch OD 4130 tubing into two saddles. Note how I used finger ... Please tell them you saw their ad in KITPLANES® Magazine. .... INTRODUCING THE LEGAL EAGLE XL.
This pattern matches axle part numbers 5030 and 5031. This pattern matches axle part numbers 5010, 5011, 5012,. 5013, 5014, 5014-1, 5015,. 5018, 5026 and ...
available as a new part. Gp 4 axles with ... The Atlas is an adapted version of the 3 litre Capri axle, and is 1" wider than the English ... prevent the back of the wheel studs on the hub carrier rubbing against the new axle ... studs. Parts laid out
it bottoms out and then pull it back quickly b. â Repeat this step until the inner tube can be pulled out from the outer tube. EC553311. Damper rod. 1. Remove:.
Such statements as that of Mr. Grant are, of course interesting but they do seem ..... John Symonds were Crowley's literary executors, entrusted with the duty of ...... second degree symbolism is, apart from its Thelemic elements, based on ...... The
its retaining pawl with the hub cutout. Install the front wheel by aligning the speedometer gear unit groove with the front shock absorber tab. Insert the axle and ...
Custom Cover by Todd Albert http://toddalbert.com/music/Cover_art. V ROY. New George's, San Rafael, CA. July 17, 1985 o1 Baby Baby. 02 Tangled Hangers ».
(1982) 'theory of sales' depicts price-setting agents as enjoying an empirical ...... a real opportunity of finding out its strength; and in consequence no theory ...
GFCI, Duplex, Switch, up to 1 9/16â Rounds. GFCI, Dúplex, interruptor, circular de hasta 1 9/16â. Disjoncteur de fuite à la terre, duplex, interrupteurs,.