DTC P1520 Stop Light Switch Signal Malfunction - caphector.com
This signal is used to detect when the brakes have been applied. The STP signal voltage is the same as the voltage supplied to the stop lights. The STP signal is ...
Stop Light Switch Signal Malfunction (Only for A/T)
CIRCUIT DESCRIPTION This signal is used to detect when the brakes have been applied. The STP signal voltage is the same as the voltage supplied to the stop lights. The STP signal is used mainly to control the fuel cut-off engine speed (The fuel cut-off engine speed is reduced slightly when the vehicle is braking.). DTC No.
DTC Detecting Condition
Trouble Area
P1520
The stop light switch does not turn off even once the vehicle is driven (2 trip detection logic)
Short in stop light switch signal circuit Stop light switch ECM
WIRING DIAGRAM S4 Stop Light Switch 1 2 G-W
G-B
Instrument Panel J/B 2 2 G-W 1B 1H
Engine ECU 15 IE2
G-W
6 E7
STP
3 1T
J10 J/C
Instrument Panel J/B STOP
8 1B
G-W C G-W C
1 1C
C
C
G-W
G-W
1 1 B* *2 B-G
R6 Stop Light LH
6
Fusible Link Block 4 ALT F6
W-B
1
6
R7 Stop Light RH
1
2
H7 High Mounted Stop Light
W-B W-B
W-B BI
Battery
BG
*1: Puerto Rico *2: Except Puerto Rico
A09139
A14313
2002 ECHO (RM884U)
Author:
Date:
299
DI-130 DIAGNOSTICS
-
ENGINE
INSPECTION PROCEDURE HINT: Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame records the engine conditions when the malfunction is detected, when troubleshooting it is useful for determining whether the vehicle was running or stopped, the engine warmed up or not, the air-fuel ratio lean or rich, etc. at the time of the malfunction.
1
Check operation of stop light.
PREPARATION: Check if the stop lights go on and off normally when the brake pedal is operated and released. NG
Check and repair stop light circuit (See page BE-37 ).
OK
2
Check STP signal. ON STP
(-)
Brake Pedal Depressed
(+)
Brake Pedal Released
When using TOYOTA hand-held tester: PREPARATION: (a) Connect the to the DLC3. (b) Turn the ignition switch ON and TOYOTA hand-held tester main switch ON. CHECK: Read the STP signal on the TOYOTA hand-held tester. OK: Brake pedal is depressed: STP ... ON Brake pedal is released: STP ... OFF When not using TOYOTA hand-held tester: PREPARATION: (a) Remove the connector cover from the ECM. (b) Turn the ignition switch ON. CHECK: Check voltage between terminal STP of ECM and body ground. OK:
D05642
OK
Brake pedal
Voltage
Depressed
7.5 - 14 V
Released
Below 1.5 V
Check for intermittent problems (See page DI-3 ).
NG 2002 ECHO (RM884U)
Author:
Date:
300
DI-131 DIAGNOSTICS
3
-
ENGINE
Check harness and connector between ECM and stop light switch (See page IN-29 ).
With IG1 terminal voltage at 8.5 V - 19 V, and when ABS is in non-operation stop light switch circuit is open for 0.3 sec. or longer. â¢Stop light valve. â¢Stop light ...
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because ... CHECK: Measure voltage between terminals IGF of the ECM connector.
ECM memory to detect mechanical trouble of the shift solenoid valve SL, valve body and torque converter clutch or automatic transaxle (clutch, brake or gear etc.) ...
2. 1. R-W. R-B. ECM. OCV+. OCV-. 10. 23. E7. E7. DI-122. -. DIAGNOSTICS. ENGINE ... (b) Connect the TOYOTA hand-held tester and select VVT from ACTIVE TEST menu. CHECK: ... Replace oil control valve, and then go to step 6. OK. 6.
vehicle driving conditions from this signal input from terminal ... After confirming DTC P0120, use the OBD II scan tool or TOYOTA hand-held tester to confirm the ...
The No.1 vehicle speed sensor outputs a 4-pulse signal for every revolution of ... â¢Open or short in vehicle speed sensor circuit ... INSPECTION PROCEDURE.
P1780. Park/Neutral Position Switch Malfunction. CIRCUIT DESCRIPTION. The neutral start switch detects the shift lever position and sends signals to the ECM.
The rotary solenoid type IAC valve is located on the throttle body and intake air bypassing the throttle valve is directed to the IAC valve through a passage.
The knock sensor is fitted to the cylinder block to detect engine knocking. This sensor contains a piezoelec- tric element which generates a voltage when it ...
Voltage output of the heated oxygen sensor remains at 0.40 V or more, or 0.50 V or less when the vehicle is driven at 40 km/h. (25 mph) or more after the engine ...
plied to the intake air temp. sensor from the terminal THA via ... After confirming DTC P0110, use the OBD II scan tool or TOYOTA hand-held tester to confirm the ...
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because ... During cranking or idling, check between terminals G2 and. NE-, NE ...
Shift solenoid valve ST is switched ON-OFF by a signal from ECM so that let in or out timing of 2nd brake is adjusted by operating orifice control valve. Therefore ...
For a fan with light(s) switched from one location. OFF. WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or ...
Aug 24, 2012 - were corrected by an ocular correction ICA transform procedure implemented by. BrainAnalyser. .... To this end, we defined the primary motor ..... participants to associate specific words with a ''Go'' or a ''NoGo'' response in a ...
Oct 10, 1997 - The MOC304_ Series are optically coupled isolators consisting of a Gallium Arsenide infrared emitting diode coupled with a mono- lithic silicon ...
When you push the SinkTop Switch⢠button, you switch electrical power between the two outlets on the power module. This feature allows a second appliance ...
real user experience, ## solution naturelle contre la transpiration des aisselles :: buy .... zippy,probleme forte odeur transpiration,je sais ou ca ramene la fouine ...