communications circuits must be separated from lighting/power circuits. 5. Use screws appropriate for the type of surface. All bases must be securely fastened to ...
SURFACE METAL RACEWAYS CANALISATIONS MÉTALLIQUES DE SURFACE HBL500/HBL700/HBL750 ELBOWS COUDES HBL500/HBL700/HBL750
CODOS HBL500/HBL700/HBL750
Directives de montage
Instrucciones de instalación
Installation Instructions English
GENERAL INFORMATION 1. NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes, communications standards, the following instructions and any instructions included with the individual raceway fittings. Refer to installation instructions for wiring device or communications device to be installed in cover or base. 2. CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing. Never wire energized electrical components. 3. NOTICE: For indoor use only. 4. NOTICE: In accordance with the NEC ® and CEC ®, data/ communications circuits must be separated from lighting/power circuits. 5. Use screws appropriate for the type of surface. All bases must be securely fastened to surface. 6. Maximum gap between raceway bases and adjacent raceway bases and/or fittings: 1/16 inch, 1.5 mm.
HBL511xx / HBL711xx/ HBL5711BRxx
90º FLAT ELBOW COUDE PLAT 90º CODO PLANO 90º
Français
RENSEIGNEMENTS GÉNÉRAUX 1. AVIS - Doit être installé par un électricien qualifié conformément aux codes de l’électricité nationaux et locaux, les normes de communication, les directives qui suivent et toutes directives incluses avec les accessoires individuels de canalisation. Se reporter aux notices de montage pour le câblage des dispositifs électriques ou de communication à être installés sur les couvercles ou dans la base. 2. ATTENTION - RISQUE DE CHOC ÉLECTRIQUE. Débrancher le circuit avant de procéder au montage. Ne jamais câbler des composants électriques dans un circuit sous tension. 3. AVIS - Pour usage à l’intérieur seulement. 4. Avis – Selon le Code canadien de l’électricité, les circuits de données/ communication doivent être séparés des circuits d’éclairage/d’énergie. 5. Utiliser des vis convenant au type de surface. Toutes les bases doivent être solidement fixées à la surface. 6. L’écart maximum entre les bases de canalisation adjacentes ou les accessoires est de 1,5 mm.
INTERNAL ELBOW COUDE INTÉRIEUR CODO INTERNO
EXTERNAL ELBOW COUDE EXTÉRIEUR CODO EXTERNO
HBL518xx / HBL718xx/ HBL5718BRxx
A) Fasten base to wall using #8 flat head fasteners - 5/16” (8 mm) head size. B) Insert raceway into base. C) Remove tab from fitting cover for HBL700 or HBL750 raceway as required. See Fig. 1 and 2. D) Snap fitting cover onto raceway. Wiring Device-Kellems Hubbell Incorporated (Delaware) 40 Waterview Drive Shelton, Connecticut 06484 (475) 882-4800
(Page 1)
HBL517xx/HBL717xx/ HBL5717BRxx
Español INFORMACIÓN GENERAL 1. AVISO - Para ser instalado por un electricista competente, de conformidad con todos los códigos eléctricos nacionales y locales, las normas de comunicaciones, las siguientes instrucciones y toda instrucción incluida en cada accesorio para la canaleta. Véanse las instrucciones de instalación para los dispositivos de cableado o los dispositivos de comunicaciones que se instalarán en la tapa o en la base. 2. ¡CUIDADO! - RIESGO DE CHOQUE ELÉCTRICO. Desconectar la energía antes de instalar. No conectar nunca componentes eléctricos en un circuito energizado. 3. AVISO: Exclusivamente para uso en interiores. 4. AVISO - De conformidad con la Norma oficial mexicana, los circuitos de datos/comunicaciones deben estar separados de los circuitos de iluminación/energía eléctrica. 5. Usar tornillos apropiados para el tipo de superficie. Todas las bases deben estar firmemente fijadas a la superficie. 6. Separación máxima entre las bases de una canaleta y las bases y/o accesorios de la canaleta adyacente: 1,5 mm.
PD2562
CANALETAS METÁLICAS DE SUPERFICIE
A) Fixer la base au mur avec des vis nº 8 à tête plate - dimension de la tête 8 mm. B) Introduire la canalisation dans la base. C) Retirer la patte du couvercle des canalisations HBL700 ou HBL750 au besoin. Consulter les Fig. 1 et 2. D) Enclencher le couvercle sur la canalisation.
A) Fijar la base a la pared usando sujetadores de cabeza plana nº 8 - tamaño de la cabeza 8 mm. B) Insertar la canaletala en la base. C) Retirar la lengüeta de la tapa de las canaletas HBL700 o HBL750 si se requiere. Ver las Fig. 1 y 2. D) Enganchar la tapa sobre la canaleta. ®
05/13
A) Fasten base to wall using #8 flat head fasteners English - 5/16” (8 mm) head size. B) Insert raceway into base. C) Remove tab from fitting cover for HBL700 or HBL750 raceway as required. See Fig. 1 and 2. D) Snap fitting cover onto raceway.
45º FLAT ELBOW COUDE PLAT 45º CODO PLANO 45º
HBL512xx / HBL712xx
A) Fixer la base au mur avec des vis nº 8 à tête plate - Français dimension de la tête 8 mm. B) Introduire la canalisation dans la base. C) Retirer la patte du couvercle des canalisations HBL700 ou HBL750 au besoin. Consulter les Fig. 1 et 2. D) Enclencher le couvercle sur la canalisation.
TWISTED ELBOW COUDE TORSADÉ CODO TRENZADO
HBL5711LHxx/ HBL5711RHxx
A) Fijar la base a la pared usando sujetadores de cabeza Español plana nº 8 - tamaño de la cabeza 8 mm. B) Insertar la canaletala en la base. C) Retirar la lengüeta de la tapa de las canaletas HBL700 o HBL750 si se requiere. Ver las Fig. 1 y 2. D) Enganchar la tapa sobre la canaleta.
HUBBELL DE MEXICO garantiza este producto, de estar libre de defectos en materiales y mano de obra por un período de un año a partir de la fecha de su compra. HUBBELL reparará o reemplazará a su juicio el producto en un plazo de 60 días. Esta garantía no cubre desgastes por uso normal o daños ocasionados por accidente, mal uso, abuso o negligencia. El vendedor no otorga otras garantías salvo lo expresado arriba y excluye expresamente daños incidentales o consecuenciales. ESTA GARANTÍA ES VÁLIDA SÓLO EN MÉXICO.
HBL500 PD2562
Fig. 1 (Page 2)
05/13
HBL700
Fig. 2
HBL700
HUBBELL DE MÉXlCO, S.A. DE C.V. Av. Insurgentes Sur # 1228 Piso 8, Col. Tlacoquemecatl del Valle México, 03200 D.F. Tel. (55) 9151-9999
NOTICE: In accordance with the NEC® and CEC®, data/ communications circuits must be separated from lighting/power circuits. 5. Use screws appropriate for ...
in accordance with all national and local electrical codes, communications standards, the following instructions and any instructions included with the individual raceway fittings. Refer to installation instructions for wiring device or communication
be used as a single unit or in conjunction with other HUBBELL .... box fittings, adapters and faceplates. TEST. 13. Test all ... CD a los equipos conectados. 17.
towards cable (Figure 5) to release snap points and remove. For immediate product information or applications assistance, call. Leviton Technical Support at ...
2. Determine which wiring scheme (T568A or T568B). If using T568B, follow the ... (Figure 4). NOTE: The wire retention technology used in these connectors.
the receptacle is no longer providing suppression. When protection is lost, an audible alarm will beep continuously. The alarm may be shut off by following the.
Este producto está certificado por NSFMR International para uso en áreas de procesamiento de alimentos expuestas a salpicaduras. Se reco-mienda seguir el siguiente procedimiento de limpieza: ¡CUIDADO! - Usar solamente productos quÃmicos y solucio
Top nuts (D) are below the groove on each valve when properly assembled. On center shank leave 1/8" .... Moen products have been manufactured under the.
With the metal cover positioned upside down over the hole in the floor, use the ... Pull the new NM Cable for the receptacle up through the hole in the flooring ...
White/Orange. Orange. White/Brown. Brown. NOTE: For some cables, wires for jack pin numbers 2, 4, 6 and 8 may have a white stripe. This is equivalent to cables with solid wires for the same pin numbers. TABLEAU 1. Modes de câblage T568A et T568B. Co
cooking generates more impurities. REMOVE OLD FILTERS. 1. Rotate old filters clockwise to remove. 2. Discard old filters. INSTALL NEW FILTERS. 1. Remove ...
and the wings are sandwiched between the drywall and the framing member ... After drywall installation install speakers in holes provided by drywall installer.
Insert the large grease tray all the way under the back edge ..... I Si un conduit de raccordement flexible est utilisé, sa longueur ne doit pas dépasser 4 pi (121,9 ...
All safety messages will follow the safety alert symbol and either the word “DANGER” or ..... F. 6" (15.2 cm) min. clearance from both sides of range to side wall.
ventilation system may cause ignition and combustion problems with this gas ...... Power Spare. RD. WH. BK WH. RD. Reignition. Module. Cooktop. Front View.