non-ducted filter kit installation instructions directives d'installation de l
cooking generates more impurities. REMOVE OLD FILTERS. 1. Rotate old filters clockwise to remove. 2. Discard old filters. INSTALL NEW FILTERS. 1. Remove ...
CONTIENT : (2) FILTRES DE RECIRCULATION NON CANALISÉS 97017930
CONTIENE: (2) FILTROS DE RECIRCULACIÓN SIN CONDUCTO 97017930
Replace filters after 25 hours of cooking or 6 months of operation. Replace more often if your cooking generates more impurities.
Remplacez les filtres après 25 heures de cuisson ou 6 mois d’utilisation. Remplacez-les plus souvent si vos cuissons produisent davantage d’impuretés.
Reemplace los filtros después de transcurridas 25 horas de cocinar o 6 meses de funcionamiento. Reemplácelo con más frecuencia si al cocinar genera más impurezas.
REMOVE OLD FILTERS
ENLEVEZ LES ANCIENS FILTRES
RETIRAR LOS FILTROS VIEJOS
1. Rotate old filters clockwise to remove. 2. Discard old filters.
1. Tournez les anciens filtres dans le sens horaire pour les enlever. 2. Jetez les anciens filtres.
1. Gire los filtros viejos en sentido horario para quitarlos. 2. Deseche los filtros viejos.
INSTALLEZ LES NOUVEAUX FILTRES
INSTALAR LOS FILTROS NUEVOS
1. Retirez les nouveaux filtres de leur sac de plastique. 2. Alignez les trous de serrure (A) de chaque filtre sur les deux taquets (B) et engagez les filtres sur les taquets. 3. Tournez les filtres dans le sens antihoraire pour les fixer.
1. Saque los filtros nuevos de las bolsas de plástico. 2. Alinee las ranuras guía (A) en cada filtro con los dos postes de enganche (B) y embrague los filtros en los postes de enganche. 3. Gire los filtros en sentido antihorario para fijarlos.
INSTALL NEW FILTERS 1. Remove new filters from their plastic bags. 2. Align key slots (A) on each filter with both latching posts (B) and engage filters over latching posts. 3. Rotate filters counterclockwise to secure.
be used as a single unit or in conjunction with other HUBBELL .... box fittings, adapters and faceplates. TEST. 13. Test all ... CD a los equipos conectados. 17.
NOTICE: In accordance with the NEC® and CEC®, data/ communications circuits must be separated from lighting/power circuits. 5. Use screws appropriate for ...
in accordance with all national and local electrical codes, communications standards, the following instructions and any instructions included with the individual raceway fittings. Refer to installation instructions for wiring device or communication
communications circuits must be separated from lighting/power circuits. 5. Use screws appropriate for the type of surface. All bases must be securely fastened to ...
towards cable (Figure 5) to release snap points and remove. For immediate product information or applications assistance, call. Leviton Technical Support at ...
2. Determine which wiring scheme (T568A or T568B). If using T568B, follow the ... (Figure 4). NOTE: The wire retention technology used in these connectors.
Este producto está certificado por NSFMR International para uso en áreas de procesamiento de alimentos expuestas a salpicaduras. Se reco-mienda seguir el siguiente procedimiento de limpieza: ¡CUIDADO! - Usar solamente productos quÃmicos y solucio
Top nuts (D) are below the groove on each valve when properly assembled. On center shank leave 1/8" .... Moen products have been manufactured under the.
White/Orange. Orange. White/Brown. Brown. NOTE: For some cables, wires for jack pin numbers 2, 4, 6 and 8 may have a white stripe. This is equivalent to cables with solid wires for the same pin numbers. TABLEAU 1. Modes de câblage T568A et T568B. Co
les exigences concernant l'installation du réfrigérateur. Coupe du tube. 2. Fermer l'arrivée d'eau. 3. Raccorder le filtre au tube d'arrivée d'eau au réfrigérateur ...
Rev-A-Shelf, L.L.C.. 2409 Plantside Dr. ⢠Jeffersontown, KY 40299 ⢠(800) 626-1126 ⢠www.rev-a-shelf.com. Base Cabinet. Base Gabinete. Armoire du bas. Spacer. Espaciador. Espaceur. Sujete el espaciador con tornillos de cabeza plana #6 x 3/4â.
the receptacle is no longer providing suppression. When protection is lost, an audible alarm will beep continuously. The alarm may be shut off by following the.
With the metal cover positioned upside down over the hole in the floor, use the ... Pull the new NM Cable for the receptacle up through the hole in the flooring ...