Go to the main fuse box, or circuit breaker. Place the main power switch ... Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow ... After the light is on, rotate the luminaire body horizontally or ...
INSTALLATION INSTRUCTION Paloma - LED Monopoint MO-LED522
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting off the electricity. - Read all instructions before installing. - System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. - Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on. - Place the wall switch in the “OFF” position. CAUTION - All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the UL/CUL listing of this fixture. AVERTISSEMENT IMPORTANT : Coupez l’électricité avant TOUTE manipulation. - Lisez toutes les instructions avant d’installer. - Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt («OFF »). - Placez l’interrupteur mural en position d’arrêt (« OFF »). MISE EN GARDE - Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation UL/CUL du luminaire.
FIG.1
Electrical Data INPUT VOLTAGE
120-277V AC, 50/60Hz
Base Plate Mounting Screw
INPUT CURRENT (MAX.) 0.2A DIMMING
ELV Base Plate
INSTALLING LAMP: (Fig.1)
1. Loosen the three canopy screws, twist and separate
Canopy Mounting Screw
the canopy cover from the base plate. (keep screws on base plate)
2. Remove a knock out from the base plate. 3. Attach the base plate to the surface using slotted holes for mounting screws (supplied).
Canopy
4. Connect fixture wires to AC power wire, with wire nuts (supplied).
355°
5. Connect ground wire to the green wire from fixture. 6. Mount the canopy to the base plate by twisting key holes over three screws in base plate.
7. Tighten screws to secure canopy.
±90° from Vertical Position
8. After the light is on, rotate the luminaire body horizontally or vertically to aim properly.
Note: All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the UL/CUL listing of this fixture. WAC Lighting www.waclighting.com Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. July, 2016
1
INSTALLATION INSTRUCTION Paloma - LED Monopoint MO-LED522
ACCESSORIES: (Fig. 2) 1. Take out the Front Cap by rotating it counter clockwise. 2. Push the original Lens Holder and LENS out from the Front Cap and replace it with the new LENS. 3. Put the Front Cap back onto the fixture.
After the light is on, rotate the luminaire body horizontally or vertically to aim properly. Note: All parts must be used as indicated in these instructions. Do not ...
All parts must be used as indicated in these instructions. Do not substitute any ... Loosen the three canopy screws, twist and separate the canopy cover from the ...
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. -. Go to the main fuse box, ...
Le non-respect de ces instructions peut annuler l'homologation UL/CUL du luminaire. INSTALLING LAMP: (Fig.1). 1. Loosen the three canopy screws, twist and ...
www.waclighting.com. Phone (800) 526.2588 • Fax (800) 526.2585. Headquarters/Eastern Distribution Center. 44 Harbor Park Drive • Port Washington, NY ...
... by a qualified electrician in accordance with the National Electrical Code and ... Grip the front cap with two fingers and rotate it gently clockwise or counter ...
66. INRUSH. CAT.III 1000V. CAT.IV 600V. 660A. True RMS. A. 660. 61-766 ... Connect the black common lead to ground or neutral before applying the red test ...
Clear or Green Textured Acrylic Bow Tie Tray. (W)12â-30 cm â (L)18â-45 cm â (H)¼â-.6 cm â 1¼ lbs.-.6 kg. Clear or Green Textured Acrylic free-formed tray ...
La Conférence générale de l'Organisation internationale du Travail, .... l'emploi illégal de travailleurs migrants, l'organisation de migrations aux fins d'emploi ...
Lecture 14. 1. 6.976 ... Addressing Systems Domain. Random Address Systems. Non-Random Address Systems ... Color and Grey Scale. ⢠Brightness and Luminance. ⢠Frame Rate. ⢠Resolution. ⢠Video .... distributed throughout the frame.
Luminescent Materials, Spinger-Verlag, ... (PDPs) are photoluminescent ... Panel Display Devices - Spring 2001. Lecture 8. 8. What is a Plasma? Solid. Liquid.
2. Remove a knock out from the base plate. 3. Attach the base plate to the surface using slotted holes for mounting screws (supplied). 4. Connect fixture wires to ...
The statutory liability for personal injury and defective products is not affected. SAP has no control over the information that you may access through the use of ...
23 avr. 2018 - 44 Harbor Park Drive • Port Washington, NY 11050 ... Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ...
Introduction. Phage antibody (Ab) library selections on peptides or proteins are usually carried out using antigens (Ags) directly coated onto a plastic surface ...
Transfer high resolution low resolution, scan board, display, high resolution screen,. 3. APPLICATION. H: Supports all VGA monitor (CRT/LCD/PDP/PROJECT).