Connecting the BeWAN ADSL Ethernet ST

information about the status of the adapter and the ADSL line: Indicator name ..... the default settings. 11. In the System Prefs menu, click on Quit System Prefs.
1MB taille 24 téléchargements 336 vues
User’s guide

Warning The information in this manual may be modified without prior notice. THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THERE IS A PARTIAL DISCREPANCY BETWEEN THE MANUAL AND THE PRODUCT IT DESCRIBES, OR IF ACCIDENTAL DAMAGE OCCURS DUE TO USE OF THIS MANUAL AND PRODUCT. The manual and the software provided is protected by Copyright law, and may not be copied or distributed in any way for any purpose. The use of the software is intended for one product only. Violation of these rules may result in prosecution by law and the person to be held responsible economically for any inconvenience and loss to the copyright owner. Copyright © 2003, BeWAN systems. All rights reserved. July 2003 edition.

Registered trademarks and copyright: • • •

BeWAN and the BeWAN systems logo are the registered trademarks of BeWAN systems. Microsoft, Windows are registered trademarks of Microsoft Corporation in the United States and/or in other countries. Macintosh is a trademark of Apple Computers, Inc. registered in the United States and in other countries.

All other trade names are the trademarks or registered trademarks of their respective holders.

BeWAN ADSL Ethernet ST

3

Table of contents Introduction............................................................................................... 5 Before starting ......................................................................................................................5 Contents of the BeWAN ADSL Ethernet ST box .................................................................5 Technical assistance .............................................................................................................6 Knowledge required .............................................................................................................6 Usage precautions.................................................................................................................7 Location .......................................................................................................................................7 Upkeep and maintenance.............................................................................................................7 Cables ..........................................................................................................................................7

The installation procedure for the BeWAN ADSL Ethernet ST ...........................................8

Connecting the BeWAN ADSL Ethernet ST ........................................... 9 Direct connection..................................................................................................................9 Indirect connection to an external hub ...............................................................................10 Specific connection: modem connection to the XboxTM Live ............................................11

Adapter indicator lights ......................................................................... 12 Access to the modem’s HTML menu .................................................... 13 From a PC ...........................................................................................................................13 From a Macintosh...............................................................................................................15

Verification and configuration of the ADSL parameters .................... 16 ADSL line synchronisation ................................................................................................16 Elements to verify in the event of non-synchronisation .............................................................16

Possible modification of the ADSL parameters .................................................................17

Installation under Windows................................................................... 18 With Windows 95...............................................................................................................18 Installation of the BeWAN PPPoE.............................................................................................18 Internet connection ....................................................................................................................20 Uninstalling the BeWAN PPPoE ...............................................................................................22

BeWAN ADSL Ethernet ST

4

With Windows 98/Me ........................................................................................................23 Installation of the BeWAN PPPoE.............................................................................................23 Internet connection ....................................................................................................................24 Uninstalling the BeWAN PPPoE ...............................................................................................26

With Windows 2000...........................................................................................................27 Installation of the BeWAN PPPoE.............................................................................................27 Internet connection ....................................................................................................................28 Uninstalling the BeWAN PPPoE ...............................................................................................30

With Windows XP..............................................................................................................31 Installation of the BeWAN PPPoE.............................................................................................31 Internet connection ....................................................................................................................32 Uninstalling the BeWAN PPPoE ...............................................................................................34

Installation under Mac OS ..................................................................... 35 With Mac OS 8.6 to 9.x......................................................................................................35 Installation of the BeWAN PPPoE.............................................................................................35 Internet connection ....................................................................................................................36 Uninstalling the BeWAN PPPoE ...............................................................................................39

With Mac OS X ..................................................................................................................40 Internet connection ....................................................................................................................40

Maintenance tools ................................................................................... 43 Modem update ....................................................................................................................43 Rebooting the modem.........................................................................................................44 Restoring the default parameters ........................................................................................45

Configuration of the computers............................................................. 46 Under Windows 98/Me ......................................................................................................46 Under Windows 2000.........................................................................................................48 Under Windows XP............................................................................................................50 Under Mac OS 8.6 to 9.x....................................................................................................52 Under Mac OS X ................................................................................................................53

BeWAN ADSL Ethernet ST

5

Introduction Congratulations, you have just acquired the BeWAN ADSL Ethernet ST, an ergonomic and highperformance modem offering dynamic management of an ADSL-based Internet connection and its sharing over a local network. Before using it, you will require a subscription with an ADSL service provider and an Internet service provider using ADSL.

Before starting In this manual, we consider that the following conditions are true: 1. You have a Analog line with an ADSL access. 2. You have a subscription with an Internet service provider (ISP), who has confirmed your connection parameters (identifiers, password, DNS servers, etc).

Contents of the BeWAN ADSL Ethernet ST box In addition to the modem guaranteed for 2 years, the BeWAN ADSL Ethernet ST box also contains the following elements:

Power supply cable a BeWAN ADSL CD-ROM containing the software and the documentation in PDF format

Straight Ethernet cable (green) used to connect the adapter to a hub

Crossed Ethernet cable (blue) used to connect the adapter to the computer an ADSL filter (only for France) The packaging should contain also: - a quick start guide, - a registration and guarantee card for the BeWAN ADSL Ethernet ST adapter.

ADSL RJ11 cable for connecting the adapter to the ADSL filter (which is connected to the telephone jack)

Note: should any of these elements be missing or damaged, contact your reseller or the BeWAN systems client services.

BeWAN ADSL Ethernet ST

6

Technical assistance The BeWAN ADSL Ethernet ST adapter and its documentation are designed to be as simple as possible, so that they can be used not only by professionals but also by the individual user at home. The BeWAN ADSL Ethernet ST User’s guide contains practical information that will allow you to rapidly install and use the BeWAN ADSL Ethernet ST adapter Before proceeding with the installation of the BeWAN ADSL Ethernet ST adapter, we recommend that you mail in or fax the guarantee registration card contained in the package. It is essential if you would like to enjoy the benefits of the after-sale service. Follow the step-by-step instructions in this User’s guide. If a problem arises: •

If you are not sure that you have installed the BeWAN ADSL Ethernet ST adapter software correctly, don’t hesitate to uninstall it and start the installation again from the beginning.



If the problems persist, write down the actions you perform and the results they produce. Then contact your dealer and provide this information. Your dealer will either assist you directly or put you in contact with the appropriate service if unable to solve the problem.

Note: for information about the BeWAN systems technical assistance service, consult the BeWAN systems web site (http://www.bewan.com).

Knowledge required In the BeWAN ADSL Ethernet ST adapter User’s guide, we assume that you are already familiar with the Windows user interface, commands and utilities. We will therefore not go over these points. If necessary, please refer to the Windows manual or the Windows on-line help. Prior knowledge of telecommunications is not necessary when using the BeWAN ADSL Ethernet ST adapter.

BeWAN ADSL Ethernet ST

7

Usage precautions Carefully read the following safety instructions before installing or using the BeWAN ADSL Ethernet ST. The usage instructions must be followed exactly.

Location •

Avoid using, placing or storing the adapter in areas which are exposed to intense light or high temperatures, or close to sources of heat. High temperatures can damage the adapter. The maximum temperature cannot not exceed 40°C.



Avoid installing the adapter in a humid or dusty area.



Keep the adapter in a secure and stable location. Serious damage could result if the adapter falls.



Keep the adapter out of the reach of children.

Upkeep and maintenance •

Do not open, disassemble or modify any part of the adapter. Any disassembly or modification could result in a strong electric discharge. Internal inspections, modifications and repairs must imperatively be carried out by accredited and qualified technicians. Opening the adapter or any internal modification will void the warranty.



Before cleaning the adapter, disconnect its power supply.



When cleaning the adapter, do not use certain chemical products which could damage plastic materials. Do not use substances containing alcohol, benzene, paint thinner or other flammable products. The use of these products can result in a fire.



Do not bring the adapter into contact with water or other liquids. No liquid must get inside the adapter. If the outside of the adapter comes into contact with a liquid, wipe it using a soft and absorbent cloth. If a liquid or other substance gets inside the adapter, disconnect the cables. If you continue using adapter, there is the risk of a fire or electrical discharge.

Cables •

Only use the supplied accessories.



Make sure that the cables are laid out such that no one can trip over them or walk on them.



Do not run the cables through a passage or in an area where they may be pinched.



When disconnecting the cables, hold the solid part. Pulling on the flexible part of the cable can damage the insulation or strip the wire, thus creating a risk of fire or electrical discharge.



Immediately discontinue using the adapter if any smoke is seen to come from it.

BeWAN ADSL Ethernet ST

8

The installation procedure for the BeWAN ADSL Ethernet ST This manual contains a detailed description of the installation procedure for the BeWAN ADSL Ethernet ST adapter. We recommend that you follow the installation steps in order. 1. Connection of your BeWAN ADSL Ethernet ST (refer to the chapter “Connecting the BeWAN ADSL Ethernet ST” on page 9). 2. Access to the modem’s Web configurator. In particular, check that you are within the same addressing range as the modem (if this is not the case, refer to the chapter “Configuration of the computers” on page 46). Note: by default, the modem’s IP address “192.168.1.1”. 3. Verification of the synchronisation and ADSL parameters. 4. Installation of the BeWAN PPPoE software in order to create your Internet connection. 5. Establishing your connection. Before beginning, deactivate any software that might disrupt the installation procedure, such as anti-virus products. Close all open applications.

BeWAN ADSL Ethernet ST

9

Connecting the BeWAN ADSL Ethernet ST This chapter provides the various connection diagrams for the BeWAN ADSL Ethernet ST. Note: when using your ADSL connection, you can simultaneously use your telephone or fax.

Direct connection Proceed as follows to directly connect a computer to the BeWAN ADSL Ethernet ST: 1. Locate the crossed Ethernet cable (blue). Connect one end of this cable to the modem’s Eth port, and the other end to the RJ45 on the computer’s Ethernet card. 2. Locate the ADSL cable (RJ11/RJ11). Connect one end of this cable to the ADSL port on the BeWAN ADSL Ethernet ST, and the other end to your phone jack. Note: the ADSL filter provided in the box must be connected to your telephone line. For the proper operation of your installation, we recommend that you place a filter on each telephone jack which is connected to the same line and to which a telephone is connected. 3. Locate the power supply cable. Connect one end of this cable to the Power port on the BeWAN ADSL Ethernet ST, and the other end to an electrical outlet which complies with the specifications indicated on the power pack.

BeWAN ADSL Ethernet ST

10

Indirect connection to an external hub To indirectly connect a computer to the BeWAN ADSL Ethernet ST, using an external Ethernet hub (not supplied), proceed as follows: 1. Obtain a straight Ethernet cable (green). Connect one end of this cable to the Eth port on the BeWAN ADSL Ethernet ST adapter, and the other end to one of the Ethernet ports on the external hub. 2. Then connect the computer to the external Ethernet hub (additional cable not provided). Note: of course, you can connect other computers and equipment to the external hub. 3. Locate the ADSL cable (RJ11/RJ11). Connect one end of this cable to the ADSL port on the BeWAN ADSL Ethernet ST, and the other end to your phone jack. 4. Locate the power supply cable. Connect one end of this cable to the DC5V port on the BeWAN ADSL Ethernet ST, and the other end to an electrical outlet which complies with the specifications indicated on the power pack.

BeWAN ADSL Ethernet ST

11

Specific connection: modem connection to the XboxTM Live The BeWAN ADSL Ethernet ST is compatible with the Xbox video game console. XboxTM Live is an online game service. To connect your modem to your Xbox console, proceed as follows: 1. Locate the crossed Ethernet cable (blue).Connect one end of the cable to the Eth (Ethernet) port on the BeWAN ADSL Ethernet ST, and the other end to the console’s Ethernet port. 2. Locate the ADSL cable (RJ11/RJ11). Connect one end of this cable to the ADSL port on the BeWAN ADSL Ethernet ST, and the other end to your phone jack. 3. Locate the power supply cable. Connect one end of this cable to the DC5V port on the BeWAN ADSL Ethernet ST, and the other end to an electrical outlet which complies with the specifications indicated on the power pack.

BeWAN ADSL Ethernet ST

12

Adapter indicator lights The BeWAN ADSL Ethernet ST adapter has three indicator lights (LED) which provide constant information about the status of the adapter and the ADSL line: Indicator name

Indicator colour

Meaning

PWR

Green

Off, when the power supply cable is not connected to the computer On, when the power supply cable is connected to the computer

SYNC

Red

On, continuously when the adapter is in "Idle" status (See the Control Panel in section “ADSL line synchronisation” on page 16) Blinks, when attempting to synchronise ("Activating / Negociating / Initialization" status) Off, once synchronised ("Synchronized" status)

LINK

Green

On, when the synchronisation with the ADSL line has been made ("Synchronized" status)

Other than these indicators on the front of the box, two other indicators are present on the back, near the Eth connector. •

The yellow flashing indicator means that the 10 Mbps connection is established.



The green flashing indicator means that the 100 Mbps connection is established.

BeWAN ADSL Ethernet ST

13

Access to the modem’s HTML menu Once the physical installation has been made, you can now configure your modem via the HTML mode. This mode provides for very easily configuring of the BeWAN ADSL Ethernet ST using your computer’s Web browser, such as Internet Explorer or Netscape Navigator). Your browsing software must be correctly configured. Note: depending on the version of the Web browser used, the dialogue boxes and the HTML page display may change slightly. In our example, we use the Microsoft Internet Explorer 6.0 software.

What you need to know to access the modem’s HTML menu: The IP address of the BeWAN ADSL Ethernet ST is “192.168.1.1” with a subnet mask of “255.255.255.0”. To access the Web configurator, your modem and your computer should be in the same addressing range. On PC, a detection tool allows you to assign to your modem a IP address compatible with your computer. On Macintosh, to access the Web configurator, for correct configuration, your computer must be assigned a static IP address within the same subnet as the IP address of the BeWAN ADSL Ethernet ST (e.g.: 192.168.1.10). To correctly configure your computer, refer to the chapter “Configuration of the computers” on page 46.

From a PC To access the Web interface, proceed as follows: 1. Launch the modem detection tool on the CD-ROM. Insert the BeWAN ADSL CD-ROM in your CD-ROM drive. If your configuration is set up for it, the installation program will launch automatically. If not, run the autorun.exe program which is located at the root of the CD-ROM. 2. Click on BeWAN ADSL Ethernet Discovery.

ST

and select your language. Click on Software, then on

BeWAN ADSL Ethernet ST

14

3. In the Discovery Status, wait for the message Found to appear. 4. In the Detected Device part: •

Device IP Address: the modem’s default IP address.



Network Interface and Subnet Mask: the IP address of your computer and its subnet mask

5. If your computer has not a static IP address in the same address format as the modem, in New IP Address, enter the new IP address of the BeWAN ADSL Ethernet ST (e.g.: 100.0.100.10). Click on Change. 6. When your modem has been found with its new IP address, click on Launch Modem Configurator…. 7. Once your browser has connected with the modem, a dialogue box appears. Here, you enter the identification elements (username and password) needed to administer the modem. By default, these identification parameters are the following: •

Username: bewan



Password: bewan

8. If you do not wish to identify yourself each time you configure the modem from this computer, click Save this password in your list of passwords. Note: in this case, anyone with access to this computer will be able to access the modem in HTML mode. 9. Once your identification is acknowledged, the Main menu of BeWAN ADSL Ethernet ST Web Configurator is displayed.

BeWAN ADSL Ethernet ST

15

From a Macintosh Caution: you should ensure that you have assigned a static IP address to your computer, and that it falls within the same addressing range as that the modem (e.G.: 192.168.1.10). To correctly configure your computer, refer to the chapter “Configuration of the computers” on page 46. 1. Launch your Internet browser. 2. In the Address heading, enter the IP address of the BeWAN ADSL Ethernet ST, and then press Enter. Reminder: by default, the IP address “192.168.1.1”. 3. Once your browser has connected with the router, a dialogue box appears. Here, you enter the identification elements (username and password) needed to administer the modem. By default, these identification parameters are the following: •

Username: bewan



Password: bewan

Note: if the dialogue box does not appear, this may mean that the IP address of the BeWAN ADSL Ethernet ST has been modified. 4. If you do not wish to identify yourself each time you configure the modem from this computer, click Save this password in your list of passwords. Note: in this case, anyone with access to this computer will be able to access the modem in HTML mode. 5. Once your identification is acknowledged, the Main menu of BeWAN ADSL Ethernet ST Web Configurator is displayed.

BeWAN ADSL Ethernet ST

16

Verification and configuration of the ADSL parameters ADSL line synchronisation You have just installed the adapter. Before you connect to the Internet, you must make sure of the proper synchronisation with the ADSL line. To this end, first make sure that your ADSL line is indeed connected to the adapter (refer to the section “Connecting the BeWAN ADSL Ethernet ST” on page 9). Proceed as follows: 1. In the System administration part, click on ADSL status. 2. Opposite the Line status heading, wait for the message Synchronized to appear. The synchronisation with the ADSL line has now been made.

Synchronisation messages: The 4-stage automatic synchronisation process will then take place. The stages are listed in the window’s Line status section: •

Activating



Negociating



Initialization



Synchronized

If these steps have proceeded normally, your ADSL line is now synchronised. To identify the presence of the synchronisation,

Elements to verify in the event of non-synchronisation If the Synchronized message does not appear, check the elements: 1. Make sure that your ADSL line is properly connected to the adapter. 2. If that does not resolve the problem, check with your operator to make sure that your ADSL line has been activated.

BeWAN ADSL Ethernet ST

17

Possible modification of the ADSL parameters During the installation, default ASDL parameters were selected. Depending on your geographical region, these parameters may not correspond with those needed for the proper operation of your modem. As such, you may be required to modify the characteristics. We recommend that you first of all obtain the necessary information from your telecom operator. If these default parameters are correct, you have only to create your Internet connection. Install the BeWAN PPPoE software to create your connection. If, however, these parameters do not correspond with those provided by your telecom operator, you will have to change them: 1. In the ADSL parameters section of the Main menu, enter the new VPI and VCI provided by your telecom operator. 2. Click on the button Apply. 3. Confirm the modifications by clicking on OK.

4. Then return to the Main menu. Click on Click here to reconnect.

5. Check that the new parameters have been correctly taken into account after the automatic reboot.

BeWAN ADSL Ethernet ST

18

Installation under Windows With Windows 95 Installation of the BeWAN PPPoE Before installing the BeWAN PPPoE software, you must have connected the BeWAN ADSL Ethernet ST. Installation of the Remote network access 1.3 The installation of the BeWAN PPPoE for Windows 95 requires the prior installation of the Remote network access 1.3. Proceed as follows: 1. Insert the BeWAN ADSL CD-ROM in your drive. Note: once the CD-ROM has been installed, the driver installation program may launch automatically. Disregard this. Close the Autorun window. 2. In the Windows Explorer, indicate the following path (supposing that your CD-ROM drive is drive D): D:\ACCpack. 3. Double-click on the msdun13uk.exe file. The following window is displayed. Click on Yes.

4. Carefully read the licence contract, and then click on Yes. The driver installation begins. 5. You will then have to restart your computer. Click on Yes.

6. The installation resumes once the computer has rebooted. Note: Windows may ask you to insert the Windows 95 CD-ROM in your PC in order to copy files for your system. Important: if a version conflict message appears, you must imperatively click on Yes in order to keep the most recent file(s).

BeWAN ADSL Ethernet ST

19

7. You will then have to restart your computer. Click on Yes.

Installing the protocol 1. Run the autorun.exe program which is located at the root of the CD-ROM. 2. Click on the product BeWAN ADSL Ethernet ST, and then select your language. 3. Click on Software and then on BeWAN PPPoE. 4. A window asks if you would like to install the PPPoE protocol. Click on Yes. 5. Carefully read the licence contract, and then click on Accept. The installation of the drivers starts. Note: Windows may ask you to insert the Windows 95 CD-ROM in your PC in order to copy files for your system. Important: if a version conflict message appears, you must imperatively click on Yes in order to keep the most recent file(s). 6. You will then have to restart your computer. Click on Yes.

Elements installed Element has been added to your system. In order to see it, click on Start, point to Settings, then click successively on Control Panel, System and on the Device Manager tab. •

In the Network adapters, the WAN/PPPOE/ADSL miniport element has been added.

BeWAN ADSL Ethernet ST

20

Internet connection Establishing your connection 1. During the installation, a connection named PPPoE connection was created. Double-click on the My Computer icon located on your desktop. 2. Then double-click on Dial-Up Networking, and then on PPPoE connection. The corresponding connection window opens. You have only to enter your identification settings.

3. Under the User name and Password headings, enter the identification parameters provided by your Internet access provider. Notes on the Internet connection: •

The terminology used by the various Internet service providers can vary. To identify the user name, the following expressions are also sometimes used: “client account”, “connection identifier”, etc.



Do not confuse the connection identifiers (user name and password) with the message system identification elements which your Internet service provider may have given you.



The connection identifiers are case sensitive.

4. If you do not want to enter your password upon each connection, select Save password. Note: in this case, any person with access to your PC will be able to access the Internet through your account. 5. Do not pay attention to the Phone number field. There is no need to modify it. Note: with the ADSL service, it is not a call number which provides the connection with the Internet service provider; rather, it is the user name.

BeWAN ADSL Ethernet ST

21

6. Then click on Connect in the connection window. The connection is carried out and your identification parameters are checked.

7. If the parameters are correct, the connection is established in a few seconds. The connection window automatically disappears. To the right of the task bar, the remote access indicator also appears. Using and ending the connection Once the connection has been made, you can use the Internet software of your choice. To visit a web site, launch your browser. When you have finished, you should disconnect. Indeed, closing the Internet software does not necessarily terminate the connection in progress. The remote access indicator, which is dependent on the Remote Access, indicates that the connection has been established. Double-clicking on this indicator will open a window which provides the main connection parameters (speed, connection duration...).

Remote access indicator

The Disconnect button will interrupt the connection. Note: you do not have to open the previously mentioned window. To interrupt the connection in progress, right-click the mouse on the remote access indicator, and then click on Disconnect.

BeWAN ADSL Ethernet ST

22

Uninstalling the BeWAN PPPoE 1. Click on Start, then point to Settings, and then click on Control Panel. 2. Double-click on the Add/Remove Programs icon. 3. In the Install/Uninstall window, select the PPP over Ethernet and then click on Add/Remove…. 4. A confirmation window opens. Click on Yes.

5. The uninstall procedure begins. Note: Windows may ask you to insert your Windows 95 CD-ROM into your PC. Important: if a version conflict message appears, you must imperatively click on Yes in order to keep the most recent file(s). 6. You will then have to restart your computer. Click on Yes.

BeWAN ADSL Ethernet ST

23

With Windows 98/Me Installation of the BeWAN PPPoE Installing the protocol 1. Insert the BeWAN ADSL CD-ROM in your drive. If your PC’s configuration is set up for it, the installation program will launch automatically. If it does not, run the autorun.exe program which is located at the root of the CD-ROM. 2. Click on the product BeWAN ADSL Ethernet ST, and then select your language. 3. Click on Software and then on BeWAN PPPoE. 4. A window asks if you would like to install the PPPoE protocol. Click on Yes. 5. Carefully read the licence contract, and then click on Accept. The installation of the drivers starts. Notes: •

With Windows 98, your Windows CD-ROM may be required during the update phase.



Windows may ask you for information about your site. Enter the area code for your region. After entering this information, click on Close.

6. A window asks if you would like to install the PPPoE protocol. Click on Yes.

Elements installed Element has been added to your system. In order to see it, click on Start, point to Settings, then click successively on Control Panel, System and on the Device Manager tab. •

In the Network adapters, the WAN/PPPOE/ADSL miniport element has been added.

BeWAN ADSL Ethernet ST

24

Internet connection Establishing your connection 1. During the installation, a connection named PPPoE connection was created. Click on Start, Programs, Accessories, Communications, then click on Dial-up Networking. 2. Double-click on PPPoE connection. The corresponding connection window opens. You have only to enter your identification settings.

With Windows 98

With Windows Me

3. Under the User name and Password headings, enter the identification parameters provided by your Internet access provider. Notes on the Internet connection: •

The terminology used by the various Internet service providers can vary. To identify the user name, the following expressions are also sometimes used: “client account”, “connection identifier”, etc.



Do not confuse the connection identifiers (user name and password) with the message system identification elements which your Internet service provider may have given you.



The connection identifiers are case sensitive.

4. If you do not want to enter your password upon each connection, select Save password. Note: in this case, any person with access to your PC will be able to access the Internet through your account. 5. Do not pay attention to the Phone number field. There is no need to modify it. Note: with the ADSL service, it is not a call number which provides the connection with the Internet service provider; rather, it is the user name.

BeWAN ADSL Ethernet ST

25

6. Then click on Connect in the connection window. The connection is carried out and your identification parameters are checked.

7. If the parameters are correct, the connection is established in a few seconds. The connection window automatically disappears. To the right of the task bar, the remote access indicator also appears. Using and ending the connection Once the connection has been made, you can use the Internet software of your choice. To visit a web site, launch your browser. When you have finished, you should disconnect. Indeed, closing the Internet software does not necessarily terminate the connection in progress. The remote access indicator, which is dependent on the Remote Access, indicates that the connection has been established. Double-clicking on this indicator will open a window which provides the main connection parameters (speed, connection duration...).

Remote access indicator

The Disconnect button will interrupt the connection. Note: you do not have to open the previously mentioned window. To interrupt the connection in progress, right-click the mouse on the remote access indicator, and then click on Disconnect.

BeWAN ADSL Ethernet ST

26

Uninstalling the BeWAN PPPoE 1. Click on Start, then point to Settings, and then click on Control Panel. 2. Double-click on the Add/Remove Programs icon. 3. In the Install/Uninstall window, select the PPP over Ethernet and then click on Add/Remove…. 4. A confirmation window opens. Click on Yes.

5. You will then have to restart your computer. Click on Yes.

BeWAN ADSL Ethernet ST

27

With Windows 2000 Installation of the BeWAN PPPoE Installing the protocol 1. Insert the BeWAN ADSL CD-ROM in your drive. If your PC’s configuration is set up for it, the installation program will launch automatically. If it does not, run the autorun.exe program which is located at the root of the CD-ROM. 2. Click on the product BeWAN ADSL Ethernet ST, and then select your language. 3. Click on Software and then on BeWAN PPPoE. 4. A window asks if you would like to install the PPPoE protocol. Click on Yes. 5. Carefully read the licence contract, and then click on Accept. The installation of the drivers starts. 6. A window indicates that the driver has been successfully installed.

Elements installed Element has been added to your system. In order to see it, click on Start, point to Settings, then click on Control Panel. After that, double-click on System. Click on the Hardware tab, and then on Device Manager…. •

In the Network adapters, the WAN/PPPOE/ADSL miniport element has been added.

BeWAN ADSL Ethernet ST

28

Internet connection Establishing your connection 1. During the installation, a connection named PPPoE connection was created. Click on Start, point to Programs, Accessories, Communications, then click on the folder Network and Dial-up Connections. It opens. 2. Double-click on PPPoE connection. The corresponding connection window opens. You have only to enter your identification settings.

3. Under the User name and Password headings, enter the identification parameters provided by your Internet access provider. Notes on the Internet connection: •

The terminology used by the various Internet service providers can vary. To identify the user name, the following expressions are also sometimes used: “client account”, “connection identifier”, etc.



Do not confuse the connection identifiers (user name and password) with the message system identification elements which your Internet service provider may have given you.



The connection identifiers are case sensitive.

4. If you do not want to enter your password upon each connection, select Save password. Note: in this case, any person with access to your PC will be able to access the Internet through your account.

BeWAN ADSL Ethernet ST

29

5. Then click on Dial in the connection window. The connection is carried out and your identification parameters are checked.

6. If the parameters are correct, the connection is established in a few seconds. The connection window automatically disappears. To the right of the task bar, the remote access indicator also appears. Using and ending the connection Once the connection has been made, you can use the Internet software of your choice. To visit a web site, launch your browser. When you have finished, you should disconnect. Indeed, closing the Internet software does not necessarily terminate the connection in progress. The remote access indicator, which is dependent on the Remote Access, indicates that the connection has been established. Double-clicking on this indicator will open a window which provides the main connection parameters (speed, connection duration...).

Remote access indicator

In the General tab, the Disconnect button will terminate the connection. Note: you do not have to open the previously mentioned window. To interrupt the connection in progress, right-click the mouse on the remote access indicator, and then click on Disconnect.

BeWAN ADSL Ethernet ST

Uninstalling the BeWAN PPPoE 1. Click on Start, then point to Settings, and then click on Control Panel. 2. Double-click on the Add/Remove Programs icon. 3. From the menu on the left, select Change or Remove Programs. 4. Select PPP over Ethernet, and then click on Change/Remove. 5. A confirmation window opens. Click on Yes.

6. You will then have to restart your computer. Click on Yes.

30

BeWAN ADSL Ethernet ST

31

With Windows XP Installation of the BeWAN PPPoE Installing the protocol 1. Insert the BeWAN ADSL CD-ROM in your drive. If your PC’s configuration is set up for it, the installation program will launch automatically. If it does not, run the autorun.exe program which is located at the root of the CD-ROM. 2. Click on the product BeWAN ADSL Ethernet ST, and then select your language. 3. Click on Software and then on BeWAN PPPoE. 4. A window asks if you would like to install the PPPoE protocol. Click on Yes. 5. Carefully read the licence contract, and then click on Accept. The installation of the drivers starts. 6. A window indicates that the driver has been successfully installed.

Elements installed Element has been added to your system. In order to see it, click on start, and then on Control Panel. Click on Performance and Maintenance and then on System. Click on the Hardware tab, and then on Device Manager. •

In the Network adapters, the WAN/PPPOE/ADSL miniport element has been added.

BeWAN ADSL Ethernet ST

32

Internet connection Establishing your connection 1. During the installation, a connection named PPPoE connection was created. Click on start, and then on Control Panel. Click on Network and Internet Connections, and then on Network Connections. 2. Double-click on PPPoE connection. The corresponding connection window opens. You have only to enter your identification settings.

3. Under the User name and Password headings, enter the identification parameters provided by your Internet access provider. Notes on the Internet connection: •

The terminology used by the various Internet service providers can vary. To identify the user name, the following expressions are also sometimes used: “client account”, “connection identifier”, etc.



Do not confuse the connection identifiers (user name and password) with the message system identification elements which your Internet service provider may have given you.



The connection identifiers are case sensitive.

4. If you do not want to enter your identifiers upon each connection, select Save this user name and password for the following users and then select Me only. Note: if you select the second option, any person with access to your PC will be able to access the Internet through your account.

BeWAN ADSL Ethernet ST

33

5. Then click on Connect in the connection window. The connection is carried out and your identification parameters are checked.

6. If the parameters are correct, the connection is established in a few seconds. The connection window automatically disappears. To the right of the task bar, the remote access indicator also appears. Using and ending the connection Once the connection has been made, you can use the Internet software of your choice. To visit a web site, launch your browser. When you have finished, you should disconnect. Indeed, closing the Internet software does not necessarily terminate the connection in progress. The remote access indicator, which is dependent on the Remote Access, indicates that the connection has been established. Double-clicking on this indicator will open a window which provides the main connection parameters (speed, connection duration...).

Remote access indicator

In the General tab, the Disconnect button will terminate the connection. Note: you do not have to open the previously mentioned window. To interrupt the connection in progress, right-click the mouse on the remote access indicator, and then click on Disconnect.

BeWAN ADSL Ethernet ST

Uninstalling the BeWAN PPPoE 1. Click on start, and then click on Control Panel. 2. Click on Add or Remove programs. 3. From the menu on the left, select Change or Remove Programs. 4. Select PPP over Ethernet, and then click on Change/Remove. 5. A confirmation window opens. Click on Yes.

6. You will then have to restart your computer. Click on Yes.

34

BeWAN ADSL Ethernet ST

35

Installation under Mac OS With Mac OS 8.6 to 9.x Installation of the BeWAN PPPoE 1. Place the BeWAN ADSL CD-ROM in your Macintosh's CD drive. 2. Double-click on the CD-ROM icon. 3. Double-click on the folder Ethernet, BeWAN PPPoE, English, then on the Installation of BeWAN PPPoE icon in order to launch the software installation program. 4. The Installation of BeWAN PPPoE window opens. Choose Easy Install. 5. Select the disk where you would like to install the BeWAN PPPoE drivers by clicking on Switch Disk. 6. Then click on Install.

7. The BeWAN PPPoE drivers are then automatically installed in the required folders of your system. 8. When completed, a message indicates that the installation has been successful. Click on Restart.

BeWAN ADSL Ethernet ST

36

Internet connection Creating your connection 1. From the Apple menu, open the Control Panels and launch the Remote Access software. The Remote Access (BeWAN PPPoE) window opens. 2. In the Remote Access menu, select Modem…. 3. A window opens where you can select the protocol which corresponds with your ADSL subscription (Connexion via) and hardware which you are using to connect (Modem). •

In the Connect via PopUp menu, select PPP over Ethernet.



In the Modem PopUp menu, select BeWAN ADSL Modem.

4. Close the window and save the changes to the configuration. 5. Return to the main Remote Access window. 6. Under the User name and Password headings, enter the identification parameters provided by your Internet access provider. Notes on the Internet connection: •

The terminology used by the various Internet service providers can vary. To identify the user name, the following expressions are also sometimes used: “client account”, “connection identifier”, etc.



Do not confuse the connection identifiers (user name and password) with the message system identification elements which your Internet service provider may have given you.



The connection identifiers are case sensitive.

7. In the Password field, enter your connection password. If you do not want to enter your password upon each connection, select Save password. Note: in this case, any person with access to your Macintosh will be able to access the Internet through your account.

BeWAN ADSL Ethernet ST

37

8. Do not pay attention to the Number field. There is no need to modify it the number “0”. Note: with the ADSL service, it is not a call number which provides the connection with the Internet service provider; rather, it is the user name.

9. To access the additional settings, click on the Options… button. Here, we will not elaborate on the additional settings which can vary according to your desires. As an example, we will simply indicate how to deprogram the automatic connection when starting up your Macintosh. Uncheck Connect automatically when starting TCP/IP applications. Click OK to validate.

BeWAN ADSL Ethernet ST

38

Establishing your connection Then click on Connect in the connection window. The connection is carried out and your identification parameters are checked. Using and ending the connection Once the connection has been made, you can use the Internet software of your choice. To visit a web site, launch your browser. When you have finished, don't forget to disconnect. Indeed, closing the Internet software does not terminate the connection in progress. To terminate it, click on the Disconnect button in the main Remote Access window

BeWAN ADSL Ethernet ST

39

Uninstalling the BeWAN PPPoE 1. Place the BeWAN ADSL CD-ROM in your Macintosh's CD drive. 2. Double-click on the CD-ROM icon. 3. Double-click on the folder Ethernet, BeWAN PPPoE, English, then on the Installation of BeWAN PPPoE icon in order to launch the software uninstall program. 4. The Installation of BeWAN PPPoE window opens. Choose Custom Remove. 5. Select BeWAN PPPoE, 6. By clicking on Switch Disk, select the disk from where you would like to uninstall the BeWAN PPPoE drivers. 7. Then click on Remove.

8. The BeWAN PPPoE drivers are automatically removed from your system. 9. When completed, a message indicates that the uninstall procedure has been successful. Click on Restart.

BeWAN ADSL Ethernet ST

40

With Mac OS X With Mac OS X, it is not necessary to install the BeWAN PPPoE. This protocol is already included in the operating system. The parameterisation and establishment of the connection using the PPPoE protocol are described below.

Internet connection Creating your connection 1. Double-click on your hard disk icon, then Applications, and then on System Preferences. 2. Click on Network. 3. In the Show pop-up menu of the Network window, select Built-in Ethernet. 4. Click on the PPPoE tab in order to enter the information about the subscription which you have taken out with an Internet access provider.

5. Check Connect using PPPoE.

BeWAN ADSL Ethernet ST

41

6. In the Service Provider field, enter your connection name. Note: this name plays no role in the connection. It serves only to identify your connection. You can therefore choose whatever you like. We thus recommend that you choose an easy to recognise name (e.g. name of your Internet service provider). 7. In the Account Name field, enter the name which you will use for your Internet service provider. Notes on the Internet connection: •

The terminology used by the various Internet service providers can vary. To identify the user name, the following expressions are also sometimes used: “client account”, “connection identifier”, etc.



Do not confuse the connection identifiers (user name and password) with the message system identification elements which your Internet service provider may have given you.



The connection identifiers are case sensitive.

8. In the Password field, enter your connection password. If you do not want to enter your password upon each connection, select Save password. Note: in this case, any person with access to your Macintosh will be able to access the Internet through your account. 9. To access the additional settings, click on the PPPoE Options… button. Here, we will not elaborate on the additional settings which can vary according to your desires As an example, we will simply indicate how to program the automatic connection when starting up your Macintosh. In the part Session Options, check Connect automatically when starting TCP/IP applications. This will immediately open a connection window when starting up. Click OK to validate.

10. Save these modifications by clicking on the Apply Now button. The settings in the TCP/IP and Proxies tabs are the default settings. 11. In the System Prefs menu, click on Quit System Prefs.

BeWAN ADSL Ethernet ST

42

Establishing your connection 1. Double-click on your hard disk icon, then Applications. Launch the Internet Connect application. 2. In the Configuration pop-up menu, the Built-in Ethernet port is already selected. The previously defined parameters are then displayed.

3. To launch the connection procedure, click on Connect. The automatic connection process will then take place in various stages. •

Contacting PPP server...



Authenticating User... (verification of the validity of your name and password).

4. The Status part changes its appearance, and displays the main connection parameters (speed, connection time,...). Using and ending the connection Once your connection has been made, you can use the Internet software of your choice. To visit a web site, launch your browser. For any additional information, refer to the software documentation. When you have finished, don't forget to disconnect. Indeed, closing the Internet software does not terminate the connection in progress. To terminate it, click on the Disconnect button.

BeWAN ADSL Ethernet ST

43

Maintenance tools Modem update The modem update is carried out in two steps. The first involves only taking the update into account in the modem’s buffer memory. If you wish to permanently update your modem, click on Save in the second part. Proceed as follows: Note: if you unplug the modem, therefore cutting off its power supply, this update will not be hardwired into the modem’s memory. 1. In the Main menu, click on Modem update. 2. In the heading Firmware image, click on Browse... in order to indicate the access path to the update file. 3. Then click on the button Send in order to load the update file into the buffer memory of the BeWAN ADSL Ethernet ST. 4. You must then imperatively click on Activate in order for the file to be taken into account.

5. To complete the update, click on Save.

BeWAN ADSL Ethernet ST

Rebooting the modem After saving an update, we recommend that you reboot your modem. Proceed as follows: 1. In the System administration part of the Main menu, click on System restart. 2. Select Keep the current configuration, then click on OK.

3. Confirm the reboot by clicking on OK.

4. Then return to the Main menu. Click on Click here to reconnect.

44

BeWAN ADSL Ethernet ST

45

Restoring the default parameters To restore the BeWAN ADSL Ethernet ST using its Web configurator, proceed as follows: 1. In the System administration part of the Main menu, click on System restart. 2. You have two possible options for restoring to the default configuration: •

Restore factory configuration: select this option if you would like the BeWAN ADSL Ethernet ST to be reset to its original configuration (LAN and ADSL parameters). Reminder: by default, the LAN and ADSL parameters are the following: IP address: 192.168.1.1 Subnet mask: 255.255.255.0 VPI: 8 VCI: 35



Restore default LAN configuration: select this option if you would like the BeWAN ADSL Ethernet ST to reboot with its configuration (LAN parameters only). Note: for the second option, and if you have changed the ADSL parameters (VPI and VCI) of the BeWAN ADSL Ethernet ST, these fields will not be modified when rebooting.

3. Confirm the restoration by clicking on OK.

4. Then return to the Main menu. Click on Click here to reconnect.

BeWAN ADSL Ethernet ST

46

Configuration of the computers Under Windows 98/Me To assign a fixed IP address to your computer, proceed as follows: 1. Click on Start, then point to Settings, and then click on Control Panel. Then double-click on the Network icon. 2. In the box The following network components are installed, select TCP/IP -> name of your network card, then click on Properties.

3. In the IP Address tab of the TCP/IP Properties window, select the option Specify an IP address. 4. In the box IP Address, enter the IP address that you have decided to assign to the PC. Important: •

The PC’s IP address must imperatively be within the same addressing range as that of the BeWAN ADSL Ethernet ST.



The PC’s IP address must be unique, i.e. different from those of the other equipment on the local network (computers, BeWAN ADSL Ethernet ST...).



The PC’s IP address must be within a range reserved for private networks. Indeed, your local network must not use addresses which are reserved for the Internet. This would cause problems when connecting your network to the Internet.

If you have any questions about these elements, please check with a network specialist.

BeWAN ADSL Ethernet ST

47

5. In the Subnet Mask field, enter the sub-network mask default value of the BeWAN ADSL Ethernet ST, i.e. “255.255.255.0”.

In the above example, the IP address and the sub-network mask assigned to the PC are compatible with the default IP parameters of the BeWAN ADSL Ethernet ST (IP address: 192.168.1.1). 6. Then click on OK in each of the windows in order to validate the changes. 7. Then reboot your computer by clicking on Yes.

BeWAN ADSL Ethernet ST

48

Under Windows 2000 To assign a fixed IP address to your computer, proceed as follows: 1. Click on Start, then point to Settings, and then click on Control Panel. Then double-click on the icon Network and Dial-up Connections. 2. Right-click the mouse on Local Area Connection, and then click on Properties in the menu. 3. Select Internet Protocol (TCP/IP), and then click on Properties.

4. Select Use the following IP address. 5. In the box IP address, enter the IP address that you have decided to assign to the PC. Important: •

The PC’s IP address must imperatively be within the same addressing range as that of the BeWAN ADSL Ethernet ST.



The PC’s IP address must be unique, i.e. different from those of the other equipment on the local network (computers, BeWAN ADSL Ethernet ST...).



The PC’s IP address must be within a range reserved for private networks. Indeed, your local network must not use addresses which are reserved for the Internet. This would cause problems when connecting your network to the Internet.

If you have any questions about these elements, please check with a network specialist.

BeWAN ADSL Ethernet ST

49

6. In the Subnet mask field, enter the sub-network mask default value of the BeWAN ADSL Ethernet ST, i.e. “255.255.255.0”.

In the above example, the IP address and the sub-network mask assigned to the PC are compatible with the default IP parameters of the BeWAN ADSL Ethernet ST (IP address: 192.168.1.1). 7. Then click on OK in each of the windows in order to validate the changes.

BeWAN ADSL Ethernet ST

50

Under Windows XP To assign a fixed IP address to your computer, proceed as follows: 1. Click on start, and then on Control Panel. 2. Click on Network and Internet Connections, and then on Network Connections. 3. Right click the mouse on Local Area Connection and then select Properties from the menu. 4. Select Internet Protocol (TCP/IP), and then click on Properties.

5. Select Use the following IP address. 6. In the box IP address, enter the IP address that you have decided to assign to the PC. Important: •

The PC’s IP address must imperatively be within the same addressing range as that of the BeWAN ADSL Ethernet ST.



The PC’s IP address must be unique, i.e. different from those of the other equipment on the local network (computers, BeWAN ADSL Ethernet ST...).



The PC’s IP address must be within a range reserved for private networks. Indeed, your local network must not use addresses which are reserved for the Internet. This would cause problems when connecting your network to the Internet.

If you have any questions about these elements, please check with a network specialist.

BeWAN ADSL Ethernet ST

51

7. In the Subnet mask field, enter the sub-network mask default value of the BeWAN ADSL Ethernet ST, i.e. “255.255.255.0”.

In the above example, the IP address and the sub-network mask assigned to the PC are compatible with the default IP parameters of the BeWAN ADSL Ethernet ST (IP address: 192.168.1.1). 8. Then click on OK in each of the windows in order to validate the changes.

BeWAN ADSL Ethernet ST

52

Under Mac OS 8.6 to 9.x To assign a fixed IP address to your computer, proceed as follows: 1. Select the Apple menu > Control panel > TCP/IP. 2. In the Connection menu, select Ethernet. 3. In the Configuration menu, select Manually. 4. In the IP address heading, indicate the IP address that you have decided to give to your Macintosh. Important: •

The Macintosh’s IP address must imperatively be within the same addressing range as that of the BeWAN ADSL Ethernet ST.



The Macintosh’s IP address must be unique, i.e. different from those of the other equipment on the local network (computers, BeWAN ADSL Ethernet ST...).



The Macintosh’s IP address must be within a range reserved for private networks. Indeed, your local network must not use addresses which are reserved for the Internet. This would cause problems when connecting your network to the Internet.

If you have any questions about these elements, please check with a network specialist. 5. In the Subnet mask heading, indicate the value of the default subnet mask of the BeWAN ADSL Ethernet ST, i.e. “255.255.255.0” 6. In the modifications confirmation window, click Save. 7. Reboot your Macintosh.

BeWAN ADSL Ethernet ST

53

Under Mac OS X To assign a fixed IP address to your computer, proceed as follows: 1. Double-click on the icon for your hard disk, then on Applications, and then System Preferences. 2. Then click on Network. 3. In the Display menu, select integrated Ethernet. 4. In the Configure menu in the TCP/IP tab, select Manually. 5. In the IP address heading, indicate the IP address that you have decided to give to your Macintosh. Important: •

The Macintosh’s IP address must imperatively be within the same addressing range as that of the BeWAN ADSL Ethernet ST.



The Macintosh’s IP address must be unique, i.e. different from those of the other equipment on the local network (computers, BeWAN ADSL Ethernet ST...).



The Macintosh’s IP address must be within a range reserved for private networks. Indeed, your local network must not use addresses which are reserved for the Internet. This would cause problems when connecting your network to the Internet.

If you have any questions about these elements, please check with a network specialist. 6. In the Subnet heading, indicate the value of the default subnet mask of the BeWAN ADSL Ethernet ST, i.e “255.255.255.0”. 7. Click on the button Apply to save the changes. 8. In the System preferences menu, click on Quit System Preferences. 9. Reboot your Macintosh.

DECLARATION OF CONFORMITY Telecommunications terminal equipment Manufacturer’s Name: BeWAN systems Address: 16, rue du Moulin des Bruyères

Telephone: 01 43 34 69 20

Postal Code: 92400

Fax: 01 46 91 03 71

Community: Courbevoie - France Product Identification Nature: ADSL Ethernet Modem Commercial reference: BeWAN ADSL Ethernet ST declares entirely on his own responsability that the product described above is in conformity with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The product is compliant with the following standards: Protection with regard to electromagnetic compatibility: EN 55022 EN 50024 EN 300386-2 FCC Part 15 Safety standards: EN 60950 UL (IEC950) Supplementary information: the product has been tested in a typical configuration. Technical file held by:

BeWAN systems R&D Dept. 16, rue du Moulin des Bruyères 92400 Courbevoie - France

Date: April 2003 Eric TEISSANDIER Chairman of the Board of Directors