1. Assemble the WLAN antennas on LCD back cover and well arrange the antenna cables through cable guides, then paste 3 pieces of tape. L C D. M O D U L E.
Assembly Procedure Please follow the information provided in this section to perform the complete assembly procedure of the Eee PC 1101HA. Be sure to use proper tools described before.
A
fter you have completed the previous chapter of complete disassembly, please follow this chapter to assemble the Eee PC 1101HA back together. This chapter describes the procedures of the complete Eee PC 1101HA assembly. In addition, in between procedures, the detailed assembly procedure of individual modules will be provided for your service needs. The assembly procedure consists of the following steps:
Bottom Case Module LCD Module Motherboard Module IO Board Module WLAN Module Card reader Board Module HDD Module Top Case Module Keyboard Module Memory Module Battery Module
3-1
Assembly procedure
B O T T O M
C A S E
M O D U L E B O T T O M
C A S E
A S S E M B L Y
Bottom Case Module The illustrations below show how to assemble the bottom case of the Eee PC 1101HA. Assemble LCD
1. Install the fan module into the bottom case and secure 1 screw here to fix it.
TOP
L C D M O D U L E
L C D A S S E M B L Y
LCD Module The illustrations below show how to assemble and install the LCD module of the Eee PC 1101HA. Assemble LCD
1. Assemble the WLAN antennas on LCD back cover and well arrange the antenna cables through cable guides, then paste 3 pieces of tape.
3-2
Assembly procedure
2. Install the CMOS DMIC CABLE on the LCD back cover and paste 2 pieces of tape here.
3. Install the camera and connect the CMOS cable.
4. Install the LCD hinges and secure 2 screws to fix them.
3-3
Assembly procedure
5. Connect the coaxial cable.
6. Install the LCD brackets and secure 4 screws to fix them.
3-4
Assembly procedure
7. Assemble the LCD panel on the LCD cover and secure 8 screws to fix it.
3-5
Assembly procedure
8. Install the LCD front bezel on LCD back cover and press the sides to fix them well.
9. Secure 6 screws (M2*4) on LCD front bezel and then fix 6 rubber pads on it.
10. Install the two LCD hinge covers.
3-6
Assembly procedure
11. Install the LCD Module on bottom case and secure 2 screws here. Then well arrange the cables and past 3 pieces of tape here.
TOP
3-7
Assembly procedure
M O T H E R B O A R D A S S E M B Y
M O T H E R B O A R D A S S E M B L Y
Motherboard Module The illustrations below show how to assemble and install the Wireless Lan Module of the Eee PC 1101HA. Assemble Motherboard
1. Install the mother board into the bottom case and secure 2 screws here to fix it.
3-8
Assembly procedure
2. Connect the LVDS cable and fan cable.
3. Connect the Bluetooth cable and install the Bluetooth module on the motherboard. Then connect the Bluetooth cable with the motherboard and paste the tape here.
3-9
Assembly procedure
4. Install the RJ45 CONNECTOR CABLE and connect it with the motherboard then paste the tape here.
TOP I O
B O A R D
M O D U L E
I O
B O A R D
I N S T A L L
IO Board Module The illustrations below show how to assemble and install the daughter Board of the Eee PC 1101HA. Installing daughter Board
1. Install the daughter board and secure 1 screw here to fix it. Then connect the speaker cable and CMOS DMIC_CABLE with it.
TOP
3 - 10
Assembly procedure
W L A N
M O D U L E
W L A N
WLAN Module The illustration shows how to install the WLAN module into the Eee PC 1101HA. Installing WLAN
1. Install the WLAN module and secure 1 screw to fix it. Then connect the WLAN antenna.
I N S T A L L
TOP
C A R D B O A R D
R E A D E R
Card reader Board Module The illustration shows how to install the card reader board into the Eee PC 1101HA.
M O D U L E
Installing card reader board C A R D B D
R E A D E R
I N S T A L L
1. Install the card reader board and secure 3 screws here to fix it.
3 - 11
Assembly procedure
2. Install and connect the SD FFC and install the SD dummy card.
TOP H D D
M O D U L E
H D D
HDD Module The illustrations below show how to assemble and install the HDD of the Eee PC 1101HA. Installing HDD
1. Install the HDD into its bracket and secure 4 screws here.
I N S T A L L
3 - 12
Assembly procedure
2. Install the HDD module and secure 1 screw to fix it.
3. Install the DAU FFC and Lock the 2 latches to connect it.
TOP
3 - 13
Assembly procedure
T O P
C A S E
M O D U L E
T O P
C A S E
A S S E M B L Y
Top case Module The illustrations below show how to assemble and install the top case module of the Eee PC 1101HA. Assemble Top case
1. Install the touchpad bracket and paste 3 pieces of Mylar here.
2. Install the touchpad board and secure 2 screws on it.
3. Install the two FFC cables and connect them with the touchpad board and the touchpad.
3 - 14
Assembly procedure
4. Install the top case on the bottom case.
5. Secure 8 screws on the bottom case.
3 - 15
Assembly procedure
6. Secure 8 screws on the top case and connect the touchpad FFC.
TOP
3 - 16
Assembly procedure
K E Y B O A R D
Keyboard The illustrations below show how to assemble and install the Keyboard of the Eee PC 1101HA.
K E Y B O A R D
Installing Keyboard
1. Connect keyboard FPC with top case.
I N S T A L L
2. Place keyboard plate on top case.
3 - 17
Assembly procedure
3. Lock the 4 latches (Esc; F6; F11; Insert) on keyboard module to fix it.
TOP
3 - 18
Assembly procedure
Memory Module M E M O R Y
The illustration below shows how to install Memory Module to the notebook. Install the Memory Module
1. Insert memory at the same 45 angles and press down until it clicks into the latches.
2. Install the memory door and secure 1 screw here.
TOP
3 - 19
Assembly procedure
B A T T E R Y
B A T T E R Y
Battery Module The illustration below shows how to install Battery Module to the notebook. Install battery module
1. Unlock and hold the latch 2 to install the battery, and lock the battery latch 1.
clabel(C,h,'manual');. As when you used clabel with 'manual' before, cross hairs will appear on ... The difference between this manual ...... subplot(spr,spc,pane);.
of length L and cross-sectional area A as shown in Fig. .... The results of tests on such reconstructed soils are often misleading since it is ... large bridges or building foundation jobs where lowering of the water table is ..... the basis of soil
yO = - 3.72 mm Ans. y|x = 550 mm =2.949 (10. -10. ) ..... By symmetry it is equivalent to use twice the integral from 0 to 8. (. ) ( ). ( ). ( ). ( ). ( ). 8. 3. 8. 2. 2. 1. 2. 0. 0. 3.
M.I.T. by I. E. Sutherland, capable of interpreting information sketched on ...... SCRA. STEP Application Handbook. U.S.A. Defense Logistics Agency, 1 June ...
Antamina mines (Chimu Formation, Valanginian) exhibits large ornithopod trackways, preserved in either concave or convex hyporelief. These footprints are ...
I, = E /[1lG + sZ + 1/(sC)] =0.21[0.5 + 3s+ 1/(5s)]. (4.21). It follows from Figure 4.4 that the output current of the series resonant circuit is eed given by this equation.
geneous information sources and allows us to quickly answer user queries independently of the availability if the data sources. We call this repository an XML.
Def 1: A parallelogram is a quadrilateral with two pairs of parallel sides. Attention: big mistake: do not mix up parallelograms and quadrilaterals : a quadrilateral ...
the human eye and the human visual cortex is highly developed, to the point ..... It is interesting to speculate about when genetic patterns will have a complex ...
true fragment position by computing the exact vectors from light or camera to .... obtained with the cross product of the normal and the tangent vector, and is.
we shall derive a simple test for determining whether or not a pin-jointed truss is .... If Eq. (4.1) is satisfied, the truss is constructed from a series of statically.
o Use external competences to help you (benchmarking, consulting). o Be patient. Lean is a long journey. This step was important for another reason. Just as it ...
Impact of Music on Restaurant Diners. Source: Ronald E. Milliman (1982), âUsing Background Music to Affect the Behavior of Supermarket Shoppers,â Journal Of.
building itself which satisfies specific needs, appeals to the aesthetic sense, and .... Darcy (1856), on the basis of his experiments on filter sands, proposed a law ...
maximum dry unit weight is called the optimum moisture content. ..... The water (moisture) content and the in-place unit weight are used to calculate the in-place ..... individual charge densifies the surrounding adjacent soil and soil beneath the ..
Obviously this model of reality may differ from that which you have adopted but the point is that at this time, .... (7) Gods - realisation of cosmic consciousness without loss of a perfected, impersonal ... energy in units of 10 to Earth, and 12 is
May 24, 2015 - occult effects: perception of energy, information, space and time, changes in aura colour and energy ... CURA's Special Edition: January 2018, http://cura.free.fr/13+/1801sergey.pdf ... You may freely reprint and host this material by
Clean caliper area. 2ï¼Using a flare nut wrench, remove hose(s). Place a container to catch brake fluid draining from brake hose. CHAPTER 7. BRAKES PAGE.
humming with activity. .... Even with gloves, my fingers get numb. .... "Why don't we go up to my flat and have a shag?" "Buzz off." And Toni would be out of there.
Mar 31, 2006 - Autothrottle (A/T) ARM Switch. ARM â Arms A/T for engagement. Magnetically held at ARM. A/T engages automatically when following AFDS ...