PROCEDURE. Step 1. Take the Vigil 2 power unit and with the orange Vigil logo facing the bottom wall of the reserve container, route the power unit UNDER.
RIGGING INNOVATIONS VIGIL 2 INSTALLATION INSTRUCTIONS BACKGROUND The following instructions are for use in assembling the Vigil 2 AAD into Rigging Innovations Inc (RI) harness and container systems. As of the below date, they are approved for use with the following systems: Talon 3.0 (Including FS and FX) Talon 2 Telesis 3.0 Telesis 2 Genera Earlier systems such as the Talon 1, Telesis 1, and Flexon, may require certain minor changes to accommodate the Vigil 2. Contact RI for further information before assembling the Vigil 2 to these systems. Needed components: 1. RI harness and container assembly with Cypres AAD installation including pocket, channels, cutter elastic, and control unit pocket. 2. Vigil 2 AAD assembly with Spectra closing loop and washer- Vigil or Cypres configuration (Figure 1). Note: The instructions and following photos are taken of a Talon FX2 system which has a small (170mm) Cypres pocket installed.
Figure 1
PROCEDURE. Step 1. Take the Vigil 2 power unit and with the orange Vigil logo facing the bottom wall of the reserve container, route the power unit UNDER the 1" loop Velcro strip located adjacent to the mouth of the pocket and then into the elastic pocket. The cutter cable should be positioned towards the top of the pocket and the control cable near the bottom of the pocket. (Figure 2). Figure 2
Step 2. Route the cutter cable out the left side of the loop Velcro as you are facing it. Loop the cable towards the bottom of the container and then route the cutter UP and BEHIND the cables BETWEEN the cable and the base of the pocket. (Figure 3).
Figure 3
Step 3. Route the cutter through the elastic channel and then position it in the elastic keeper and UNDER the TY-12 cutter protector. (Figure 4).
Figure 4
Step 4. Pull the excess cable out the bottom of the pocket and form a gentle loop. (Figure 5).
Figure 5
Step 5. Stow this excess cable in the pocket located in the bottom tray between the stiffener plate and the AAD pocket on the center wall. (Figure 6).
Step 6. Take the control head and route it UNDER the cover of the channel in the bottom of the pack tray. (Figure 7).
Figure 7
Step 7. Route the control head OUT THE TOP of the channel and place into the pocket at the top of the container. Coil the excess cable as in Figure 8, and then insert it back into the channel as in Figure 9. The result should look like Figure 10 with the cable exiting from the far side of the channel to form a gentle loop to the control head. Figure 8
Figure 9
Figure 10
Step 8. Close the Velcro pocket cover flap (Figure 11). The assembly is now complete. Check the operation of the unit to make sure all connections are secure and that the AAD is operational.
When you are setting the jumpers, make sure that the jumper caps are placed on the correct pins to ... This jumper lets you erase the system setup settings that are stored in. CMOS memory. You might ..... case with a screw. 7. For some add&in ...
pocket. 2. Vigil 2 AAD assembly with Spectra closing loop and washer- Vigil or Cypres configuration (Figure 1). Note: The instructions and following photos are.
Pin #. TxD. 2. RxD. 3. GND. 5. Operation*. Main or Auxiliary Repeater. RF Link. 60 ft (18 m) maximum. Wired Link 1000 ft. (305 m) maximum. 30 ft (9 m) maximum. 30 ft (9 m) maximum. 30 ft (9 m) maximum. Wired and RF Configuration. Setup. Wired. RF. Co
(1) 1 A fast-acting fuse. ULâ¦Class CC ; IECâ¦gG. Fusible rapide 1 A. ULâ¦Class CC ; IECâ¦gG. Schnellsicherung 1 A. ULâ¦Klasse CC ; IECâ¦gG. Fusible rápido ...
Silhouette® and Nantucket⢠window shadings are made of 100% polyester, which means they are inherently durable and resilient. However, care must be taken to avoid wrinkling the fabric, particularly where the vanes meet the facings. The Palette® F
Allumez toujours la hotte lorsque vous cuisinez à haute température ou que vous faites f amber des aliments. c. Nettoyez fréquemment les ventilateurs de la ...
Si el frente de su ducha es removible, lÃmpiela periódicamente removiendo el frente destornillando el tornillo central. Si votre douche est munie d'une façade ...
2 intermediate shaft assembly with the bolt. ... AND WASHER SWITCH AND SPIRAL CABLE ... (c) Push into the light control switch and headlight dimmer switch ...
Installation Steps: 1. The stub-out pipe for installation must be 5/8'' (+/- 1/8'') measured from the finished wall surface. Apply plumber's tape (included) to the pipe ...
materials, will fully satisfy your requirements. This new appliance is very ..... This circuit-breaker should be sized in compliance with local installation regulations.
3¼" x 10", Roof jack and shutter. N/A. 6. 5. 6. 10. NOTE: These commonly used installation parts can be purchased at a local hardware store. Thermador does ...
Check with the local plumbing code requirements before installation. This product is recommended to be ... Antes de la instalación, consulte las exigencias del código local de plomerÃa. El producto se recomienda de ser ... llave hexagonal. Retirer
and standards, including fire-rated construction codes and standards. 4. Sufficient air is needed for proper combustion and exhausting of gases through the flue ...
Retirez les quatre écrous encastrables en nylon de 1/4 po des poteaux du ventilateur et retirez la plaque coulissante. Tournez le ventilateur de. 90 degrés vers ...
For Lazer, Halo Miniature and circuit #1 of. Haloâ2 , track contact must be in clown posi- tion (Fig A). For Halo-2 Circuit #2, move con- tact to the up position (Fig.
If LP, the LP cylinder must be unhooked and stored outside in a well ... is not intended to be installed in or on recreational vehicles, trailers and/or boats. Note:.
and the American Society for Heating, Refrigeration and Air Conditioning ..... nationale de la Protection contre les Incendies (nePa) et par les Ingénieurs de ... et de l'air Climatisé (asHrae) et par les autorités responsables des codes locaux. ....
property damage, personal injury or death. ○ Do not ..... opening a window or by increasing the power of the mechanical exhaust system if installed. WARNING ...
Do not touch any electrical switch; do not use any .... exhaust dryer into a chimney, a wall, a ceiling, an attic, ...... (mise à la terre) pour assurer votre protection.
2 Filtres à tamis métalliques. 2 Ampoules halogènes (préinstallées). 1 Collier de transition circulaire de 7". 1 Collier de transition rectangulaire de 3 1/4" x 10" ...