command is wrong; the mask should be 0.0.0.255. OSPF-PxR1-b.txt The address in the network 192.162.xx.0 0.0.0.255 area 0 command is wrong; it should be ...
Procedure These are the troubleshooting scenarios at the time this lab guide was written.
Troubleshooting VLANs and Trunks File name
Description
VLAN-a.txt
VLAN 2x is deleted; interface FastEthernet0/10 is still assigned to VLAN 2x. The VLAN must be re-created. Note that this file deletes VLANs 21, 22, 23, 24, 25, 26 so it can be used for all pods.
VLAN-b.txt
The switch’s FastEthernet 0/11 is changed to switchport mode dynamic auto. The core switch interface is also configured for dynamic auto, so they don't negotiate trunking.
VLAN-c.txt
The switch’s FastEthernet 0/1 to PxR1 native VLAN was changed to VLAN 10; it should be VLAN 1.
VLAN-d.txt
The switch’s FastEthernet 0/1 to PxR1 was changed to be an access port; it should be a trunk.
VLAN-e.txt
The switch’s FastEthernet 0/2 interface is shut down. It should be operational.
VLAN-f.txt
The switch’s FastEthernet 0/2 is in VLAN 1. It should be on VLAN 3x.
VLAN-g.txt
The switch is only allowing VLAN 1 on the FastEthernet 0/1 trunk to PxR1. It should allow VLANs 1, 1x, 2x, 3x on this trunk.
VLAN-h.txt
The switch’s address is configured under interface VLAN 1 but it is in the wrong subnet. The address is 10.1.77.100; it should be 172.16.1.1x3, in the VLAN1 subnet.
Troubleshooting IP Connectivity File name
Description
On PCs
No entry in local hosts file for “Server”; need to add.
IP-SW-a.txt
The switch’s default gateway is set to wrong address, 10.10.7.1. It should be 10.10.x.1.
IP-PxR2-b.txt
The default route on PxR2 to PxR1 was deleted. It should be ip route 0.0.0.0 0.0.0.0 10.3.x.1.
Note
IP-R1-c.txt
C-2
There is a separate file for each pod; substitute the “x” in the file name with your pod number.
In ACL 100 on PxR1, the permit ip any any was replaced with permit tcp any any.
There is a separate file for each pod; substitute the “x” in the file name with your pod number.
File name
Description
EIGRP-PxR1-a.txt
The passive-interface GigabitEthernet 0/1 command is configured; it should not be there.
EIGRP-PxR1-b.txt
The GigabitEthernet 0/1 interface is shutdown; it should be up.
EIGRP-PxR1-c.txt
The commands network 10.1.x.0 0.0.0.255 and network 10.2.x.0 0.0.0.255 were deleted. They need to be put back.
EIGRP PxR1-d.txt
There is an incorrect IP address and mask on interface GigabitEthernet 0/0.3x. It is 10.3.7.1/24; it should be 10.3.x.1/24.
EIGRP PxR1-e.txt
There is an incorrect EIGRP AS number; it is 10 but it should be 100.
EIGRP PxR1-f.txt
The passive-interface GigabitEthernet 0/0.3x command is configured; it should not be there.
EIGRP PxR1-g.txt
The forth octet of the EIGRP wildcard mask in the network 192.168.xx.0 0.0.0.0 command is wrong; the mask should be 0.0.0.255.
EIGRP PxR1-h.txt
The “K-values” (metric weights) were changed from the defaults. You can change them back to the defaults by either using metric weights 0 1 0 1 0 0, or (even easier) no metric weights; both of these commands go under the EIGRP process (router eigrp 100).
There is a separate file for each pod; substitute the “x” in the file name with your pod number.
File name
Description
OSPF-PxR1-a.txt
The fourth octet of the OSPF network 10.3.x.0 0.0.0.0 area x command is wrong; the mask should be 0.0.0.255.
OSPF-PxR1-b.txt
The address in the network 192.162.xx.0 0.0.0.255 area 0 command is wrong; it should be 192.168.xx.0.
OSPF-PxR1-c.txt
The passive-interface GigabitEthernet 0/1 command is configured; it should not be there.
OSPF-PxR1-d.txt
The gigabit 0/0.3x interface is shutdown; it should be no shutdown.
OSPF-PxR1-e.txt
The network 10.10.x.0 0.0.0.255 area x command is missing. It needs to be put back.
OSPF-PxR1-f.txt
The hello interval on GigabitEthernet 0/0.3x is set to 5 seconds, it should be 10 seconds. You can change it using the interface configuration command ip ospf hello-interval 10.
OSPF-PxR1-g.txt
PxR1’s router ID is set to 10.200.x.2, resulting in the same router ID as PxR2. PxR1’s router ID should be its own loopback 100 interface address. You can remove the router ID using the router configuration command no router-id; you will have to restart the OSPF process, using the clear ip ospf process command in order for this change to take effect.
OSPF-PxR1-h.txt
The IP address on GigabitEthernet 0/1 is set to 192.168.77.1/24. It should be 192.168.xx.1/24.
Troubleshooting a Serial Connection Note
C-4
There is a separate file for each pod; substitute the “x” in the file name with your pod number.
File name
Description
Serial-PxR1-a.txt
The password on the username command is changed from cisco to Cisco. On the Serial 0/0/0 interface the PPP authentication mode is changed to PAP, and then the interface is shutdown. The authentication mode should be CHAP.
The link between PxSW and the core switch should be configured for EtherChannel using LACP, but the EtherChannel is not working (one port is blocked by STP). This is because PxSW is configured for PAgP, but core switch is still configured for LACP. To fix, change PxSW to LACP.
Super-R1-b.txt
The Serial 0/0/0 interface is shutdown. The encapsulation is changed from PPP to HDLC. The encapsulation ppp command needs to be put back on the interface, and the interface needs to be enabled.
Super-PxR1-c.txt
In the OSPF process 1, the network 192.168.x.96 0.0.0.31 area x command is missing. It needs to be put back.
Note
Super-R1-d.txt
There is a separate file for each pod; substitute the “x” in the file name with your pod number.
The ipv6 eigrp 100 command is missing on interface GigabitEthernet 0/1.
... your pod number for x and the router number for y in all instructions and ... The following table lists the commands used in this lab, in alphabetical order. ..... configuration you will also see more detail in the crypto pki certificate section
life and limb exploring the mysterious continent of Lustria. The lure of riches and .... as detailed in the Psychology section of the. Mordheim rulebook. 0-1 Wulfen.
Administration on which recordings can be made, and also appears in Cisco Unity .... For users who use Mozilla Firefox on Red Hat Linux workstations, the J2SE ...
Matrix Publishing, LLC. logo are trademarks of Matrix Publishing, LLC. Talonsoft and the ... intervention. Crete 1941 .... This models the US lead offensive that would lead to the breakout of the hedgerow ... This models Germany's armored assault fol
The river is ... river. If this happens, it takes an additional S3 hit and is washed onto the ..... 'Senore Andres, maybe we should head back to the shoreline eh?
NOTE: Actual cycle times vary based on soil level, water temperature, and options ... AutoSense This cycle automatically senses the soil level and adjusts the ...
procurer en visitant notre site Web à l'adresse www.electromenagersge.ca. ...... adquirir una tira de prueba de agua dura de GE Appliances. Llame al ...
tensioned the belt properly but after starting the engine the alternator will not work? ... Q: After installing an overhauled gear driven aircraft alternator, I am ...
basket before adding clothes. Step 5. • Press Start to begin the wash cycle. The machine will weigh your clothes and add the proper amount of water. When the ...
is connected to the “C” (internal blue screened) valve. □ Install or store where ... NOTE: The washer performs automatic system checks after pressing the Start button. Water will flow in 45 ... If the display is active, press to put the washer into s
are, consult your local or state consumer affairs office or your state's Attorney General. Warrantor: GE ... Order on-line today 24 hours every day. In the US: ...
4. Rear brake shoe clearance (Out of adjustment). 5. Pad or lining (Cracked or distorted). 6. Piston (Stuck). 7. Piston (Frozen). 8. Anchor or return spring (Faulty).
DO NOT allow children to play on or in this appliance. .... If the washer is running, pressing it once will pause the washer and unlock the ... The chart below will help you match the items to be washed with the best ..... the remaining portion of th
New technologies have brought about changes in approaches to teaching, ..... aussi être renforcés par l'idéal du savoir accessible à tous – idéal que la société.
lesser reward, as they may be useful in recreating the recipe, even without their ... are ignored if the warrior failed his Initiative test, or chose to drop the pies â which has ..... Mind you, beggars can't be choosers, and as there was nobody el
The mechanics there said it was working normally. ... To prevent surprises, first understand how the system ... cylinder, and what it doesn't use will go to the other ...