4. Rear brake shoe clearance (Out of adjustment). 5. Pad or lining (Cracked or distorted). 6. Piston (Stuck). 7. Piston (Frozen). 8. Anchor or return spring (Faulty).
PROBLEM SYMPTOMS TABLE Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part in order. If necessary, replace these parts. Symptom
Lower pedal or spongy pedal
Brake drag
Suspect Area
See page
5. Brake system (Fluid leaks) 6. Brake system (Air in) 7. Piston seals (Worn or damaged) 8. Rear brake shoe clearance (Out of adjustment) 9. Master cylinder (Faulty) 10.Booster push rod (Out of adjustment)
Brake pedal freeplay (Minimal) Parking brake lever travel (Out of adjustment) Parking brake wire (Sticking) Rear brake shoe clearance (Out of adjustment) Pad or lining (Cracked or distorted)
6. Piston (Stuck) 7. Piston (Frozen) 8. Anchor or return spring (Faulty) 9. Booster push rod (Out of adjustment) 10.Booster system (Vacuum leaks) 11.Master cylinder (Faulty) 1. Piston (Stuck)
3. Piston (Frozen) 4. Disc (Scored) 5. Pad or lining (Cracked or distorted)
1. Brake system (Fluid leaks) 2. Brake system (Air in) 3. Pad or lining (Worn) 4. Pad or lining (Cracked or distorted)
Hard pedal but brake inefficient
5. Rear brake shoe clearance (Out of adjustment) 6. Pad or lining (Oily) 7. Pad or lining (Glazed) 8. Disc (Scored) 9. Booster push rod (Out of adjustment) 10.Booster system (Vacuum leaks)
NOTE: Actual cycle times vary based on soil level, water temperature, and options ... AutoSense This cycle automatically senses the soil level and adjusts the ...
procurer en visitant notre site Web à l'adresse www.electromenagersge.ca. ...... adquirir una tira de prueba de agua dura de GE Appliances. Llame al ...
tensioned the belt properly but after starting the engine the alternator will not work? ... Q: After installing an overhauled gear driven aircraft alternator, I am ...
basket before adding clothes. Step 5. • Press Start to begin the wash cycle. The machine will weigh your clothes and add the proper amount of water. When the ...
is connected to the “C” (internal blue screened) valve. □ Install or store where ... NOTE: The washer performs automatic system checks after pressing the Start button. Water will flow in 45 ... If the display is active, press to put the washer into s
are, consult your local or state consumer affairs office or your state's Attorney General. Warrantor: GE ... Order on-line today 24 hours every day. In the US: ...
DO NOT allow children to play on or in this appliance. .... If the washer is running, pressing it once will pause the washer and unlock the ... The chart below will help you match the items to be washed with the best ..... the remaining portion of th
The mechanics there said it was working normally. ... To prevent surprises, first understand how the system ... cylinder, and what it doesn't use will go to the other ...
command is wrong; the mask should be 0.0.0.255. OSPF-PxR1-b.txt The address in the network 192.162.xx.0 0.0.0.255 area 0 command is wrong; it should be ...
part of the radiators with duct tape (experimental airplanes only, please). .... settings, leading to high temperatures, the octane rating of the fuel is less than what it ...
Door not closed properly. Controller malfunctioning. Door alignment. Damaged door seal. Drip pan not in place. Excess grease or oil build-up in unit. Drain tube ...
Make certain all connectors are clean and secure. 2. Reverse connections ... Cool or heat the probe to a known temperature and check the resistance. Degree F.
Page 7 ... Tarlton, who edited EDN's popular Design Ideas section, worked with Bob on a .... readers have written commentsâin addition to making requests for more ... notes asserting that Bob's articles were marvelous; the best that EDN had ... AI
5. Unless otherwise noted, set the line voltage to. 230Vac!10%, 50Hz. ... the same as the Table below. 5. Press OK(Y) button to memorize the data. ... EP (East-west Parabolar) ... and specification. ...... MANUAL,OWNERS FS,LG,FR 009K.