TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

•

•

TLC2201B Is 100% Tested for Noise: 30 nV/√Hz Max at f = 10 Hz 12 nV/√Hz Max at f = 1 kHz Low Input Offset Voltage . . . 200 µV Max Excellent Offset Voltage Stability With Temperature . . . 0.5 µV/°C Typ

• •

• •

Low Input Bias Current 1 pA at TA = 25°C Fully Specified for Both Single-Supply and Split-Supply Operation Common-Mode Input Voltage Range Includes the Negative Rail

description

TYPICAL EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY V n – Equivalent Input Noise Voltage – nV/ HzHz Vn

The TLC2201, TLC2201A, TLC2201B, and TLC2201Y are precision, low-noise operational amplifiers using Texas Instruments Advanced LinCMOS process. These devices combine the noise performance of the lowest-noise JFET amplifiers with the dc precision available previously only in bipolar amplifiers. The Advanced LinCMOS process uses silicon-gate technology to obtain input offset voltage stability with temperature and time that far exceeds that obtainable using metal-gate technology. In addition, this technology makes possible input impedance levels that meet or exceed levels offered by top-gate JFET and expensive dielectric-isolated devices. The combination of excellent dc and noise performance with a common-mode input voltage range that includes the negative rail makes these devices an ideal choice for high-impedance, low-level signal conditioning applications in either single-supply or split-supply configurations.

60 VDD = 5 V RS = 20 Ω TA = 25°C

50

40

30

20

10

0 1

10

100

1k

10 k

f – Frequency – Hz

The device inputs and outputs are designed to withstand – 100-mA surge currents without sustaining latch-up. In addition, internal ESD-protection circuits prevent functional failures at voltages up to 2000 V as tested under MIL-STD-883C, Method 3015.2; however, care should be exercised in handling these devices as exposure to ESD may result in degradation of the device parametric performance. AVAILABLE OPTIONS PACKAGED DEVICES TA

VIOmax AT 25°C

Vnmax f = 10 Hz AT 25°C

Vnmax f = 1 kHz AT 25°C

0C 0°C to 70°C

200 µV 200 µ µV 500 µV

35 nV/√Hz 30 nV/√Hz —

– 40°C 40 C to 85°C

200 µV 200 µ µV 500 µV

– 55°C 55 C to 125°C C

200 µV 200 µ µV 500 µV V

CHIP FORM (Y)

SMALL OUTLINE (D)

CHIP CARRIER (FK)

CERAMIC DIP (JG)

PLASTIC DIP (P)

15 nV/√Hz 12 nV/√Hz —

TLC2201ACD TLC2201BCD TLC2201CD

—

—

TLC2201ACP TLC2201BCP TLC2201CP

TLC2201Y

35 nV/√Hz 30 nV/√Hz —

15 nV/√Hz 12 nV/√Hz —

TLC2201AID TLC2201BID TLC2201ID

—

—

TLC2201AIP TLC2201BIP TLC2201IP

—

35 nV/√Hz 30 nV/√Hz —

15 nV/√Hz 12 nV/√Hz —

TLC2201AMD TLC2201BMD TLC2201MD

TLC2201AMJG TLC2201BMJG TLC2201MJG

TLC2201AMP TLC2201BMP TLC2201MP

—

TLC2201AMFK TLC2201BMFK TLC2201MFK

The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2201BCDR). Chip-form versions are tested at 25°C only.

Advanced LinCMOS is a trademark of Texas Instruments Incorporated. Copyright  1994, Texas Instruments Incorporated

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

1

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

description (continued) The C-suffix devices are characterized for operation from 0°C to 70 °C. The l-suffix devices are characterized for operation from – 40 °C to 85 °C. The M-suffix devices are characterized for operation over the full military temperature range of – 55 °C to 125 °C.

1

8

2

7

3

6

4

5

NC VDD + OUT NC

NC IN – NC IN + NC

4

3 2 1 20 19 18

5

17

6

16

7

15

8

14 9 10 11 12 13

NC VDD – /GND NC NC NC

NC IN – IN + VDD – /GND

FK PACKAGE (TOP VIEW)

NC NC NC NC NC

D, JG, OR P PACKAGE (TOP VIEW)

NC – No internal connection

2

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

NC VDD + NC OUT NC

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

equivalent schematic (each amplifier) VDD + Q3

Q6

Q9

Q12

Q14

Q16

IN + OUT

C1 IN – Q1

Q4 Q13

Q15

Q17

D1 Q7

Q8

Q10

Q11 R1

Q2

R2

Q5

VDD – COMPONENT COUNT Transistors Diodes R i Resistors Capacitors

POST OFFICE BOX 655303

17 1 2 1

• DALLAS, TEXAS 75265

3

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

TLC2201Y chip information This chip, when properly assembled, displays characteristics similar to the TLC2201C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding path. Chips may be mounted with conductive epoxy or a gold-silicon preform. BONDING PAD ASSIGNMENTS

(8)

(7)

(6)

IN – IN +

(2) (3)

VDD+ (7) +

(6) OUT

– (4) VDD –

77

CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 × 4 MINIMUM TJmax = 150°C TOLERANCES ARE ± 10%. ALL DIMENSIONS ARE IN MILS. (1)

(2)

(3)

(4)

TERMINAL NUMBERS ARE FOR THE D, JG, AND P PACKAGES.

65

4

PIN (4) IS INTERNALLY CONNECTED TO BACK SIDE OF CHIP.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

absolute maximum ratings over operating free-air temperature (unless otherwise noted)† Supply voltage, VDD + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V Supply voltage, VDD – (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 8 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 16 V Input voltage, VI (any input) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 8 V Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 mA Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature. TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or P package . . . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD + and VDD – . 2. Differential voltages are at IN+ with respect to IN –. 3. The output can be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE

TA ≤ 25°C POWER RATING

DERATING FACTOR ABOVE TA = 25°C

TA = 70°C POWER RATING

TA = 85°C POWER RATING

TA = 125°C POWER RATING

D

725 mW

5.8 mW/°C

464 mW

377 mW

145 mW

FK

1375 mW

11.0 mW/°C

880 mW

715 mW

275 mW

JG

1050 mW

8.4 mW/°C

672 mW

546 mW

210 mW

P

1000 mW

8.0 mW/°C

640 mW

520 mW

200 mW

recommended operating conditions C SUFFIX Supply voltage, VDD ± Common-mode input voltage, VIC Operating free-air temperature, TA

I SUFFIX

M SUFFIX

MIN

MAX

MIN

MAX

MIN

MAX

± 2.3

±8

± 2.3

±8

± 2.3

±8

VDD – 0

VDD + – 2.3 70

POST OFFICE BOX 655303

VDD – – 40

• DALLAS, TEXAS 75265

VDD + – 2.3 85

VDD – – 55

VDD + – 2.3 125

UNIT V V °C

5

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER

TEST CONDITIONS

Input offset voltage

αVIO

Temperature coefficient of input offset voltage

TYP

MAX

100

500

Full range

Input offset voltage long-term drift (see Note 4) IIO

Input offset current

IIB

Input bias current

VICR

C Common-mode d input i p voltage l g range g

VOM +

Maximum positive peak output voltage swing

600

Full range RS = 50 Ω

VIC = 0 0,

25°C

0.001

25°C

0.5

25°C

RS = 50 Ω

Maximum negative peak output voltage swing VO = ± 4 V V,

RL = 500 kΩ

VO = ± 4 V V,

RL = 10 kΩ

L Large-signal i l diff differential i l voltage l amplification lifi i

CMRR

Common-mode rejection ratio

VIC = VICRmin, VO = 0, RS = 50 Ω

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

VDD ± = ± 2.3 2 3 V to ± 8 V

IDD

Supply current

VO = 0 0,

No load

0.005 100

1

Full range

100

F ll range Full g

–5 to 2.7

25°C

4.7

Full range

4.7

25°C

– 4.7

Full range

– 4.7

25°C

400

Full range

300

25°C

90

Full range

70

25°C

90

Full range

85

25°C

90

Full range

85

25°C

UNIT µV µV/°C

05 0.5

Full range

RL = 10 kΩ

AVD

TLC2201C MIN

25°C

VIO

VOM –

TA†

µV/mo pA pA

V 4.8

V

– 4.9

V

560 V/ V V/mV

100 115

dB

110 1.1

Full range

dB 1.5 1.5

mA

† Full range is 0°C to 70°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER

TEST CONDITIONS VO = ± 2.3 V, CL = 100 pF F

SR

Slew rate at unity gain

Vn

Equivalent input noise voltage

VN(PP)

Peak-to-peak equivalent input noise voltage

In

Equivalent input noise current Gain-bandwidth product

φm Phase margin at unity gain † Full range is 0°C to 70°C.

6

RL = 10 kΩ,

TA† 25°C Full range

TLC2201C MIN

TYP

2

2.7

1.5

f = 10 Hz

25°C

18

f = 1 kHz

25°C

8

f = 0.1 to 1 Hz

25°C

0.5

f = 0.1 to 10 Hz

25°C

0.7

MAX

UNIT V/µs

nV/√Hz µV

25°C

0.6

fA/√Hz

f = 10 kHz,, CL = 100 pF

RL = 10 kΩ,,

25°C

19 1.9

MHz

RL = 10 kΩ,

CL = 100 pF

25°C

48°

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER VIO

Input offset voltage

αVIO

Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4)

IIO

Input offset current

IIB

Input bias current

VICR

Common-mode input voltage range

VOM +

Maximum positive peak output voltage swing

VOM –

AVD

Maximum negative peak output voltage swing

Large signal L Large-signal i l diff differential i l voltage amplification

TEST CONDITIONS

TA†

TLC2201AC MIN

25°C

MAX

80

200

Full range

RS = 50 Ω

25°C

VO = ± 4 V V,

RL = 500 kΩ RL = 10 kΩ

100 1

100 – 5 to 2.7 2 7

25°C

4.7

Full range

4.7

25°C

– 4.7

Full range

– 4.7

25°C

400

Full range

300

25°C

90

Full range

70

Common-mode rejection ratio

VIC = VICRmin, VO = 0, RS = 50 Ω

25°C

90

Full range

85

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

VDD ± = ± 2.3 2 3 V to ± 8 V

25°C

90

Full range

85

IDD

Supply current

VO = 0 0,

25°C

100 – 5 to 2.7 2 7

4.8

4.7 – 4.7

4.8

400

– 4.9

90

pA pA

V

560

300 100

µV/mo

V

– 4.7 560

µV

V

4.7 – 4.9

UNIT

µV/°C

0.5

1

CMRR

No load

200

100

Full range

VO = ± 4 V V,

80

0.001 0.005

0.5

25°C

RL = 10 kΩ

MAX

05 0.5

0.001 0.005

25°C

F ll range Full

TYP

300

05 0.5

Full range

RS = 50 Ω

MIN

300

Full range 0 VIC = 0,

TLC2201BC

TYP

V/ V V/mV

100

70 115

90

115

dB

85 110

90

110

dB

85 1.1

1.5

Full range

1.1

1.5

1.5

1.5

mA

† Full range is 0°C to 70°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER

TLC2201AC

TEST CONDITIONS

TA†

MIN

TYP

VO = ± 2.3 V, RL = 10 kΩ, CL = 100 pF

25°C

2

2.7

TLC2210BC

MAX

MIN

TYP

2

2.7

MAX

UNIT

SR

Slew rate at unity gain

Vn

Equivalent input noise voltage (see Note 5)

f = 10 Hz

25°C

18

35

18

30

f = 1 kHz

25°C

8

15

8

12

VN(PP)

Peak-to-peak Peak to peak equivalent input noise voltage

f = 0.1 to 1 Hz

25°C

0.5

0.5

f = 0.1 to 10 Hz

25°C

0.7

0.7

In

Equivalent input noise current

25°C

0.6

0.6

fA/√Hz

25°C

19 1.9

19 1.9

MHz

Gain-bandwidth product

f = 10 kHz, RL = 10 kΩ, CL = 100 pF

Full range

1.5

V/µs

1.5

nV/√Hz µV

φm Phase margin at unity gain RL = 10 kΩ, CL = 100 pF 25°C 48° 48° † Full range is 0°C to 70°C. NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

7

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER

TEST CONDITIONS

TA†

TLC2201C MIN

25°C

TYP

MAX

100

500

VIO

Input offset voltage

αVIO

Temperature coefficient of input offset voltage

Full range

Input offset voltage long-term drift (see Note 4)

25°C

0.001

25°C

0.5

Full range

Input offset current

IIB

Input bias current

VICR

C Common-mode d input i p voltage l g range g

RS = 50 Ω

VOH

Maximum high-level output voltage

RL = 10 kΩ

VOL

Maximum low-level output voltage

IO = 0

AVD

RS = 50 Ω

VIC = 0 0,

IIO

600

1

Full range

L i l diff differential i l voltage l amplification lifi i Large-signal

100

F ll range Full g

0 to 2.7

25°C

4.7

Full range

4.7

25°C

4.8 0

150

Full range

100

VO = 1 V to 4 V, RL = 10 kΩ

25°C

25

Full range

15

25°C

90

Full range

85

25°C

90

Full range

85

CMRR

Common-mode rejection ratio

VIC = VICRmin, VO = 0, RS = 50 Ω

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

4 6 V to 16 V VDD = 4.6

IDD

Supply current

VO = 2 2.5 5V V,

No load

25°C

pA pA

V 50 50

25°C

µV/mo

V

Full range

VO = 1 V to 4 V, RL = 500 kΩ

0.005 100

25°C

µV µV/°C

0.5

Full range

UNIT

mV

315 V/ V V/mV

55 110

dB

110 1

Full range

dB 1.5 1.5

mA

† Full range is 0°C to 70°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER

TEST CONDITIONS VO = 0.5 V to 2.5 V, RL = 10 kΩ, CL = 100 pF

SR

Slew rate at unity gain

Vn

Equivalent input noise voltage

VN(PP)

Peak-to-peak equivalent input noise voltage

In

Equivalent input noise current Gain-bandwidth product

φm Phase margin at unity gain † Full range is 0°C to 70°C.

8

TLC2201C

TA†

MIN

TYP

25°C

1.8

2.5

Full range

1.3

MAX

UNIT V/µs

f = 10 Hz

25°C

18

f = 1 kHz

25°C

8

f = 0.1 to 1 Hz

25°C

0.5

f = 0.1 to 10 Hz

25°C

0.7

25°C

0.6

fA/√Hz MHz

f = 10 kHz,, CL = 100 pF

RL = 10 kΩ,,

25°C

18 1.8

RL = 10 kΩ,

CL = 100 pF

25°C

45°

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

nV/√Hz µV

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO

Input offset voltage

αVIO

Temperature p coefficient of input p offset voltage Input offset voltage long-term drift (see Note 4)

TEST CONDITIONS

TA†

TLC2201AC MIN

25°C

MAX

80

200

Full range

RS = 50 Ω

Input offset current

IIB

Input bias current

VICR

Common-mode input voltage range

RS = 50 Ω

VOH

Maximum high-level g output p voltage

RL = 10 kΩ

VOL

Maximum low-level output p voltage

IO = 0

AVD

Large-signal differential L g ig l diff i l voltage amplification

25°C

0.001 0.005

0 to 2 7 2.7

25°C

4.7

Full range

4.7

1

25°C 25°C

150

Full range

100 15

25°C

90

Full range

85

25°C

90

Full range

85

IDD

Supply current

VO = 2 2.5 5V V, No load

4.7

4.8

25°C

315

0

50 50

150 25

pA pA

mV

315

100 55

µV/mo

V

4.7 50

µV

V

50

Full range

VDD = 4 4.6 6 V to 16 V

4.8 0

25

Supply pp y voltage g rejection j ratio (∆VDD ± /∆VIO)

100 0 to 2 7 2.7

Full range

25°C

kSVR

100

100

F ll range Full

UNIT

µV/°C

0.5

1

VO = 1 V to 4 V,, RL = 10 kΩ VIC = VICRmin,, VO = 0, RS = 50 Ω

200

100

25°C

Common-mode rejection ratio

80

0.001 0.005

0.5

Full range

CMRR

MAX

05 0.5

Full range

VO = 1 V to 4 V,, RL = 500 kΩ

TYP

300

05 0.5

25°C

IIO

MIN

300

Full range 0 VIC = 0,

TLC2201BC

TYP

V/ V V/mV

55

15 110

90

110

dB

85 110

90

110

dB

85 1

1.5

Full range

1

1.5

1.5

1.5

mA

† Full range is 0°C to 70°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER

TLC2201AC

TEST CONDITIONS

TA†

MIN

TYP

VO = 0.5 0 5 V to 2.5 2 5 V, V, RL = 10 kΩ, CL = 100 pF

25°C

18 1.8

25 2.5

Full range

1.3

TLC2210BC

MAX

MIN

TYP

18 1.8

25 2.5

MAX

UNIT

SR

Sl Slew rate at unity i gain i

Vn

Equivalent q input p noise voltage g (see Note 5)

f = 10 Hz

25°C

18

35

18

30

f = 1 kHz

25°C

8

15

8

12

VN(PP)

Peak-to-peak p equivalent q input p noise voltage

f = 0.1 to 1 Hz

25°C

0.5

0.5

f = 0.1 to 10 Hz

25°C

0.7

0.7

In

Equivalent input noise current

25°C

0.6

0.6

fA/√Hz

25 C 25°C

18 1.8

18 1.8

MH MHz

G i bandwidth Gain b d idth product d t Gain-bandwidth

kHz,R RL = 10 kΩ, f = 10 kHz, CL = 100 pF

V/ V/µs

1.3

nV/√Hz µV

φm Phase margin at unity gain RL = 10 kΩ kΩ, CL = 100 pF 25°C 45° 45° † Full range is 0°C to 70°C. NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

9

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER

TEST CONDITIONS

Input offset voltage

αVIO

Temperature coefficient of input offset voltage

TYP

MAX

100

500

Full range

Input offset voltage long-term drift (see Note 4) IIO

Input offset current

IIB

Input bias current

VICR

C Common-mode d input i p voltage l g range g

VOM +

Maximum positive peak output voltage swing

650

Full range RS = 50 Ω

VIC = 0 0,

25°C

0.001

25°C

0.5

25°C

RS = 50 Ω

Maximum negative peak output voltage swing VO = ± 4 V V,

RL = 500 kΩ

VO = ± 4 V V,

RL = 10 kΩ

L Large-signal i l diff differential i l voltage l amplification lifi i

CMRR

Common-mode rejection ratio

VIC = VICRmin, VO = 0, RS = 50 Ω

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

VDD ± = ± 2.3 2 3 V to ± 8 V

IDD

Supply current

VO = 0 0,

No load

0.005 150

1

Full range

150

F ll range Full g

–5 to 2.7

25°C

4.7

Full range

4.7

25°C

– 4.7

Full range

– 4.7

25°C

400

Full range

250

25°C

90

Full range

65

25°C

90

Full range

85

25°C

90

Full range

85

25°C

UNIT µV µV/°C

05 0.5

Full range

RL = 10 kΩ

AVD

TLC2201I MIN

25°C

VIO

VOM –

TA†

µV/mo pA pA

V 4.8

V

– 4.9

V

560 V/ V V/mV

100 115

dB

110 1.1

Full range

dB 1.5 1.5

mA

† Full range is – 40°C to 85°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER

TEST CONDITIONS VO = ± 2.3 V, CL = 100 pF

SR

Slew rate at unity gain

Vn

Equivalent input noise voltage

VN(PP)

Peak-to-peak equivalent input noise voltage

In

Equivalent input noise current Gain-bandwidth product

φm Phase margin at unity gain † Full range is – 40°C to 85°C.

10

RL = 10 kΩ,

TA† 25°C Full range

TLC2201I MIN

TYP

2

2.7

1.4

f = 10 Hz

25°C

18

f = 1 kHz

25°C

8

f = 0.1 to 1 Hz

25°C

0.5

f = 0.1 to 10 Hz

25°C

0.7

MAX

UNIT V/µs

nV/√Hz µV

25°C

0.6

fA/√Hz

f = 10 kHz,, CL = 100 pF

RL = 10 kΩ,,

25°C

19 1.9

MHz

RL = 10 kΩ,

CL = 100 pF

25°C

48°

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER VIO

Input offset voltage

αVIO

Temperature p coefficient of input offset voltage Input offset voltage long-term drift (see Note 4)

IIO

Input offset current

IIB

Input bias current

VICR

Common-mode input voltage range

VOM +

Maximum positive peak p p output voltage swing

VOM –

AVD

Maximum negative g p peak output voltage swing Large-signal L g ig l diff differential i l voltage amplification

CMRR Common-mode rejection ratio

TEST CONDITIONS

TA†

TLC2201AI MIN

25°C

TYP

MAX

80

200

Full range

RS = 50 Ω

25°C

VO = ± 4 V V,

RL = 10 kΩ

–5 to 2 2.7

25°C

4.7

Full range

4.7

25°C

– 4.7

Full range

– 4.7

25°C

400

Full range

250

25°C

90

Full range

65

25°C

90

Full range

85

25°C

90

Full range

85

Supply pp y voltage g rejection j ratio (∆VDD ± /∆VIO)

VDD ± = ± 2.3 2 3 V to ± 8 V

IDD

Supply current

VO = 0 0,

No load

150 1

150

F ll range Full g

25°C

150 –5 to 2 2.7

4.8

4.7 – 4.7

4.8

400

– 4.9

90

pA pA

V

560

250 100

µV/mo

V

– 4.7 560

µV

V

4.7 – 4.9

UNIT

µV/°C

0.5

1

VIC = VICRmin,, VO = 0, RS = 50 Ω

kSVR

200

150

25°C

RL = 500 kΩ

80

0.001 0.005

0.5

Full range

VO = ± 4 V V,

MAX

05 0.5

0.001 0.005

25°C

RL = 10 kΩ

TYP

350

05 0.5

Full range

RS = 50 Ω

MIN

350

Full range 0 VIC = 0,

TLC2210BI

V/ V V/mV

100

65 115

90

115

dB

85 110

90

110

dB

85 1.1

1.5

Full range

1.1

1.5

1.5

1.5

mA

† Full range is – 40°C to 85°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150 °C extrapolated to TA = 25°C using the Arrhenius equation assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER

TEST CONDITIONS

TA†

3V VO = ± 2 2.3 V,, RL = 10 kΩ, CL = 100 pF

Full range

25°C

TLC2201AI MIN

TYP

2

27 2.7

TLC2210BI

MAX

MIN

TYP

2

27 2.7

MAX

UNIT

SR

Sl Slew rate at unity i gain i

Vn

Equivalent input q p noise voltage g (see Note 5)

f = 10 Hz

25°C

18

35

18

30

f = 1 kHz

25°C

8

15

8

12

VN(PP)

Peak-to-peak p equivalent q input p noise voltage

f = 0.1 to 1 Hz

25°C

0.5

0.5

f = 0.1 to 10 Hz

25°C

0.7

0.7

In

Equivalent input noise current

25°C

0.6

0.6

fA/√Hz

25°C 25 C

19 1.9

19 1.9

MHz MH

G i bandwidth Gain-bandwidth Gain b d idth product d t

f = 10 kHz, kHz,R RL = 10 kΩ, CL = 100 pF

1.4

V/ V/µs

1.4

nV/√Hz µV

φm Phase margin at unity gain RL = 10 kΩ kΩ, CL = 100 pF 25°C 48° 48° † Full range is – 40°C to 85°C. NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

11

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER

TEST CONDITIONS

TLC2201I MIN

25°C

VIO

Input offset voltage

αVIO

Temperature coefficient of input offset voltage

TYP

MAX

100

500

Full range

Input offset voltage long-term drift (see Note 4)

650

Full range RS = 50 Ω

VIC = 0 0,

IIO

Input offset current

IIB

Input bias current

VICR

C Common-mode d input i p voltage l g range g

RS = 50 Ω

VOH

Maximum high-level output voltage

RL = 10 kΩ

VOL

Maximum low-level output voltage

IO = 0

AVD

TA†

0.001

25°C

0.5

Full range 25°C

1

L Large-signal i l diff differential i l voltage l amplification lifi i

150

F ll range Full g

0 to 2.7

25°C

4.7

Full range

4.7

25°C

4.8 0

VO = 1 V to 4 V, RL = 10 kΩ

CMRR

Common-mode rejection ratio

VIC = VICRmin, VO = 0, RS = 50 Ω

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

VDD = 4.6 4 6 V to 16 V

IDD

Supply current

VO = 2 2.5 5V V,

No load

25°C

150 100

25°C

25

Full range

15

25°C

90

Full range

85

25°C

90

Full range

85

25°C

pA pA

V 50 50

Full range

µV/mo

V

Full range

VO = 1 V to 4 V, RL = 500 kΩ

0.005 150

Full range

µV µV/°C

05 0.5

25°C

UNIT

mV

315 V/ V V/mV

55 110

dB

110 1

Full range

dB 1.5 1.5

mA

† Full range is – 40°C to 85°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER

TEST CONDITIONS VO = 0.5 V to 2.5 V, RL = 10 kΩ, CL = 100 pF

SR

Slew rate at unity gain

Vn

Equivalent input noise voltage

VN(PP)

Peak-to-peak equivalent input noise voltage

In

Equivalent input noise current Gain-bandwidth product

φm Phase margin at unity gain † Full range is – 40°C to 85°C.

12

TLC2201I

TA†

MIN

TYP

25°C

1.8

2.5

Full range

1.2

f = 10 Hz

25°C

18

f = 1 kHz

25°C

8

f = 0.1 to 1 Hz

25°C

0.5

f = 0.1 to 10 Hz

25°C

0.7

MAX

UNIT V/µs

nV/√Hz µV

25°C

0.6

fA/√Hz

f = 10 kHz,, CL = 100 pF

RL = 10 kΩ,,

25°C

18 1.8

MHz

RL = 10 kΩ,

CL = 100 pF

25°C

45°

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO

Input offset voltage

αVIO

Temperature p coefficient of input offset voltage Input offset voltage long-term drift (see Note 4)

TEST CONDITIONS

TLC2201AI MIN

25°C

MAX

80

200

RS = 50 Ω

IIB

Input bias current

VICR

Common-mode input voltage range

RS = 50 Ω

VOH

Maximum high-level output g p voltage

RL = 10 kΩ

VOL

Maximum low-level output p voltage

IO = 0

AVD

Large-signal L g ig l diff differential i l voltage amplification

25°C

0.001 0.005

1 150

F ll range Full g

0 to 2 2.7

25°C

4.7

Full range

4.7

25°C

Supply pp y voltage g rejection j ratio (∆VDD ± /∆VIO)

VDD = 4 4.6 6 V to 16 V

IDD

Supply current

VO = 2 2.5 5V V,

No load

150

1

150 0 to 2 2.7

4.8

4.7 50

4.8

25°C

150 100

25°C

25

Full range

15

25°C

90

Full range

85

25°C

90

Full range

85

25°C

315

0

50 50

150 25

pA pA

mV

315

100 55

µV/mo

V

50

Full range

µA

V

4.7 0

UNIT

µV/°C

0.5

Full range

kSVR

200

150

25°C

VIC = VICRmin,, VO = 0, R S = 50 Ω

80

0.001 0.005

0.5

Full range

VO = 1 V to 4 V,, RL = 10 kΩ

MAX

05 0.5

Full range

VO = 1 V to 4 V,, RL = 500 kΩ

TYP

350

05 0.5

25°C

Input offset current

MIN

350

Full range 0 VIC = 0,

TLC2201BI

TYP

Full range

IIO

CMRR Common-mode rejection ratio

TA†

V/ V V/mV

55

15 110

90

110

dB

85 110

90

110

dB

85 1

1.5

Full range

1

1.5

1.5

1.5

mA

† Full range is – 40°C to 85°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER

TLC2201AI

TEST CONDITIONS

TA†

MIN

TYP

0 5 V to 2.5 2 5 V, V, VO = 0.5 RL = 10 kΩ, CL = 100 pF

25°C

18 1.8

25 2.5

Full range

1.2

TLC2210BI

MAX

MIN

TYP

18 1.8

25 2.5

MAX

UNIT

SR

Sl Slew rate at unity i gain i

Vn

Equivalent input q p noise voltage g (see Note 5)

f = 10 Hz

25°C

18

35

18

30

f = 1 kHz

25°C

8

15

8

12

VN(PP)

Peak-to-peak p equivalent q input p noise voltage

f = 0.1 to 1 Hz

25°C

0.5

0.5

f = 0.1 to 10 Hz

25°C

0.7

0.7

In

Equivalent input noise current

25°C

0.6

0.6

fA/√Hz

25°C

18 1.8

18 1.8

MHz

Gain-bandwidth product

f = 10 kHz,, RL = 10 kΩ,, CL = 100 pF

V/ V/µs

1.2

nV/√Hz µV

φm Phase margin at unity gain RL = 10 kΩ kΩ, CL = 100 pF 25°C 45° 45° † Full range is – 40°C to 85°C. NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

13

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER

TEST CONDITIONS

Input offset voltage

αVIO

Temperature coefficient of input offset voltage

TYP

MAX

100

500

Full range

Input offset voltage long-term drift (see Note 4) IIO

Input offset current

IIB

Input bias current

VICR

C Common-mode d input i p voltage l g range g

VOM +

Maximum positive peak output voltage swing

700

Full range RS = 50 Ω

VIC = 0 0,

25°C

0.001

25°C

0.5

25°C

RS = 50 Ω

Maximum negative peak output voltage swing VO = ± 4 V V,

RL = 500 kΩ

VO = ± 4 V V,

RL = 10 kΩ

L Large-signal i l diff differential i l voltage l amplification lifi i

CMRR

Common-mode rejection ratio

VIC = VICRmin, VO = 0, RS = 50 Ω

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

VDD ± = ± 2.3 2 3 V to ± 8 V

IDD

Supply current

VO = 0 0,

No load

0.005 500

1

Full range

500

F ll range Full g

–5 to 2.7

25°C

4.7

Full range

4.7

25°C

– 4.7

Full range

– 4.7

25°C

400

Full range

200

25°C

90

Full range

45

25°C

90

Full range

85

25°C

90

Full range

85

25°C

UNIT µV µV/°C

05 0.5

Full range

RL = 10 kΩ

AVD

TLC2201M MIN

25°C

VIO

VOM –

TA†

µV/mo pA pA

V 4.8

V

– 4.9

V

560 V/ V V/mV

100 115

dB

110 1.1

Full range

dB 1.5 1.5

mA

† Full range is – 55°C to 125°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER

TEST CONDITIONS VO = ± 2.3 V, CL = 100 pF F

SR

Slew rate at unity gain

Vn

Equivalent input noise voltage

VN(PP)

Peak-to-peak equivalent input noise voltage

In

Equivalent input noise current Gain-bandwidth product

φm Phase margin † Full range is – 55°C to 125°C.

14

RL = 10 kΩ,

TA† 25°C Full range

TLC2201M MIN

TYP

2

2.7

1.3

f = 10 Hz

25°C

18

f = 1 kHz

25°C

8

f = 0.1 to 1 Hz

25°C

0.5

f = 0.1 to 10 Hz

25°C

0.7

MAX

UNIT V/µs

nV/√Hz µV

25°C

0.6

fA/√Hz

f = 10 kHz,, CL = 100 pF

RL = 10 kΩ,,

25°C

19 1.9

MHz

RL = 10 kΩ,

CL = 100 pF

25°C

48°

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER VIO

Input offset voltage

αVIO

Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4)

IIO

Input offset current

IIB

Input bias current

VICR

Common-mode Common mode input voltage range

VOM OM+

Maximum positive peak output voltage swing

VOM –

AVD

Maximum negative peak output voltage swing

Large signal L Large-signal i l diff differential i l voltage amplification

TA†

TEST CONDITIONS

TLC2201AM MIN

MAX

80

200

25°C Full range

RS = 50 Ω

25°C

0.001

25°C

0.5

25°C

Full F ll range g

–5 to 2.7

25°C

4.7

Full range

4.7 – 4.7 – 4.7

25°C

400

Full range

200

VO = ± 4 V, RL = 10 kΩ

25°C

90

Full range

45

25°C

90

Full range

85

25°C

90

Full range

85

Common mode rejection Common-mode ratio

VIC = VICRmin, VO = 0, RS = 50 Ω

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

VDD ± = ± 2.3 2 3 V to ± 8 V

IDD

Supply current

VO = 0 0,

No load

200

0.005

0.001

0.005

500 1 500 –5 to 2.7

4.8

4.7

25°C Full range

– 4.7

4.8

400

– 4.9

90

pA pA

V

560

200 100

µV/mo

V

– 4.7 560

µV

V

4.7 – 4.9

UNIT

µV/°C

0.5

500

25°C

CMRR

80

05 0.5

1

Full range VO = ± 4 V, RL = 500 kΩ

MAX

500

Full range

RL = 10 kΩ

TYP

400

05 0.5

Full range

RS = 50 Ω

MIN

400

Full range 0 VIC = 0,

TLC2210BM

TYP

V/ V V/mV

100

45 115

90

115

dB

85 110

90

110

dB

85 1.1

1.5 1.5

1.1

1.5 1.5

mA

† Full range is – 55°C to 125°C. NOTE 4: Typical values are based on the input offset voltage shift observable through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

15

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER

SR

Sl Slew rate at unity i gain i

TEST CONDITIONS VO = ± 2 2.3 3V V, kΩ RL = 10 kΩ, CL = 100 pF

TLC2201AM

TA†

MIN

TYP

25°C

2

27 2.7

TLC2201BM MAX

MIN

TYP

2

27 2.7

MAX

V/ V/µs Full range

1.3

1.3

Vn

Equivalent input noise voltage (see Note 5)

f = 10 Hz

25°C

18

35

18

30

f = 1 kHz

25°C

8

15

8

12

VN(PP)

Peak to peak equivalent input Peak-to-peak noise voltage

f = 0.1 to 1 Hz

25°C

0.5

0.5

f = 0.1 to 10 Hz

25°C

0.7

0.7

In

Equivalent input noise current

φm

UNIT

nV/√Hz µV

25°C

0.6

0.6

fA/√Hz

Gain-bandwidth p d G i b d id h product

f = 10 kHz, RL = 10 kΩ,, CL = 100 pF

25°C

1.9 19

1.9 19

MHz MH

Phase margin at unity gain

RL = 10 kΩ,, CL = 100 pF

25°C

48°

48°

† Full range is – 55°C to 125°C. NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

16

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER

TEST CONDITIONS

TLC2201M MIN

25°C

VIO

Input offset voltage

αVIO

Temperature coefficient of input offset voltage

TYP

MAX

100

500

Full range

Input offset voltage long-term drift (see Note 4)

700

Full range RS = 50 Ω

VIC = 0 0,

IIO

Input offset current

IIB

Input bias current

VICR

C Common-mode d input i p voltage l g range g

RS = 50 Ω

VOH

Maximum high-level output voltage

RL = 10 kΩ

VOL

Maximum low-level output voltage

IO = 0

AVD

TA†

0.001 0.005*

25°C

0.5

Full range

500

25°C

1

Full range

L Large-signal i l diff differential i l voltage l amplification lifi i

500

F ll range Full g

0 to 2.7

25°C

4.7

Full range

4.7

25°C

4.8 0

VO = 1 V to 4 V, RL = 10 kΩ

CMRR

Common-mode rejection ratio

VIC = VICRmin, VO = 0, RS = 50 Ω

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

VDD = 4.6 4 6 V to 16 V

IDD

Supply current

VO = 2 2.5 5V V,

No load

25°C

150 75

25°C

25

Full range

10

25°C

90

Full range

85

25°C

90

Full range

85

25°C

pA pA

V 50 50

Full range

µV/mo

V

Full range

VO = 1 V to 4 V, RL = 500 kΩ

µV µV/°C

05 0.5

25°C

UNIT

mV

315 V/ V V/mV

55 110

dB

110 1

Full range

dB 1.5 1.5

mA

∗On products compliant to MIL-STD-883, Class B, this parameter is not production tested. † Full range is – 55°C to 125°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER SR

Slew rate at unity gain

Vn

Equivalent input noise voltage

VN(PP)

Peak to peak equivalent Peak-to-peak input noise voltage

In

Equivalent input noise current Gain-bandwidth product

φm Phase margin at unity gain † Full range is – 55°C to 125°C.

TEST CONDITIONS VO = 0.5 V to 2.5 V, RL = 10 kΩ, CL = 100 pF

TLC2201M

TA†

MIN

TYP

25°C

1.8

2.5

Full range

1.1

MAX

UNIT V/µs

f = 10 Hz

25°C

18

f = 1 kHz

25°C

8

f = 0.1 to 1 Hz

25°C

0.5

f = 0.1 to 10 Hz

25°C

0.7

25°C

0.6

fA/√Hz MHz

f = 10 kHz,, CL = 100 pF

RL = 10 kΩ,,

25°C

18 1.8

RL = 10 kΩ,

CL = 100 pF

25°C

45°

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

nV/√Hz µV

17

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO

Input offset voltage

αVIO

Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4)

MAX

80

200

RS = 50 Ω

IIB

Input bias current

VICR

Common-mode Common mode input voltage range

RS = 50 Ω

VOH

Maximum high high-level level output voltage

RL = 10 kΩ

VOL

low-level Maximum low level output voltage

IO = 0

25°C

0.001

25°C

0.5

25°C

Full F ll range g

0 to 2.7

25°C

4.7

Full range

4.7

Full range

75

VO = 1 V to 4 V, RL = 10 kΩ

25°C

25

Full range

10

25°C

90

Full range

85

25°C

90

Full range

85

VDD = 4 4.6 6 V to 16 V

IDD

Supply current

5V VO = 2 2.5 V,

No load

0.001

25°C Full range

0.005

0.5 500 1 500

4.8

4.7

4.8

315

0

50 50

150 25

pA pA

V

315

75 55

µV/mo

V

4.7 50

µV

V

50 150

Supply voltage rejection ratio (∆VDD ± /∆VIO)

0.005

UNIT

µV/°C

0 to 2.7

0

25°C

kSVR

200

500

25°C

VIC = VICRmin, VO = 0, RS = 50 Ω

80

05 0.5

1

Full range

Common mode rejection Common-mode ratio

MAX

500

Full range

CMRR

TYP

400

05 0.5

Full range

VO = 1 V to 4 V, RL = 500 kΩ

MIN

400

Full range 0 VIC = 0,

TLC2210BM

TYP

25°C

Input offset current

Large signal L Large-signal i l diff differential i l voltage amplification

TLC2201AM MIN

Full range

IIO

AVD

TA†

TEST CONDITIONS

V/ V V/mV

55

10 110

90

110

dB

85 110

90

110

dB

85 1.1

1.5 1.5

1.1

1.5 1.5

mA

† Full range is – 55°C to 125°C. NOTE 4: Typical values are based on the input offset voltage shift observable through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

18

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER

SR

Sl Slew rate at unity i gain i

TLC2201AM

TEST CONDITIONS

TA†

MIN

TYP

VO = 0.5 0 5 V to 2 2.5 5V V, kΩ RL = 10 kΩ, CL = 100 pF

25°C

18 1.8

25 2.5

Full range

1.1

TLC2201BM MAX

MIN

TYP

18 1.8

25 2.5

MAX

V/ V/µs 1.1

Vn

Equivalent input noise voltage (see Note 5)

f = 10 Hz

25°C

18

35

18

30

f = 1 kHz

25°C

8

15

8

12

VN(PP)

Peak to peak equivalent input Peak-to-peak noise voltage

f = 0.1 to 1 Hz

25°C

0.5

0.5

f = 0.1 to 10 Hz

25°C

0.7

0.7

In

Equivalent input noise current

φm

UNIT

nV/√Hz µV

25°C

0.6

0.6

fA/√Hz

Gain-bandwidth p d G i b d id h product

f = 10 kHz, RL = 10 kΩ,, CL = 100 pF

25°C

1.8 18

1.8 18

MHz MH

Phase margin at unity gain

RL = 10 kΩ,, CL = 100 pF

25°C

45°

45°

† Full range is – 55°C to 125°C. NOTE 5: This parameter is tested on a sample basis for the TLC2201A and on all devices for the TLC2201B. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

19

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

electrical characteristics at VDD± = ±5 V, TA = 25°C (unless otherwise noted) PARAMETER VIO

TEST CONDITIONS

Input offset voltage Input offset voltage long-term drift (see Note 4)

IIO IIB

TLC2201Y MIN

VIC = 0 0,

Input offset current

RS = 50 Ω

Input bias current

VICR

C Common-mode d input i p voltage l g range g

RS = 50 Ω

0 to 2.7

VOH VOL

Maximum high-level output voltage

RL = 10 kΩ

4.7

Maximum low-level output voltage

AVD

Large-signal differential voltage amplification

IO = 0 VO = 1 V to 4 V,

CMRR

Common-mode rejection ratio

kSVR

Supply voltage rejection ratio (∆VDD ± /∆VIO)

VO = 1 V to 4 V, VIC = VICRmin, VO = 0,

TYP

MAX

100

500

0.001

0.005

UNIT µV µV/mo

0.5

pA

1

pA V

4.8 0

V 50

mV

RL = 500 Ω

25

55

RL = 10 Ω

25

55

RS = 50 Ω

90

110

dB

90

110

dB

VDD = 4.6 to 16 V VO = 2.5 V,

V/mV

IDD Supply current per amplifier No load 1 1.5 mA NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

operating characteristics at VDD ± = ± 5 V, TA = 25°C PARAMETER SR

Positive slew rate at unity gain

Vn

Equivalent input noise voltage

VN(PP)

Peak to peak equivalent Peak-to-peak input noise voltage

In

Equivalent input noise current

φm

20

TLC2201Y

TEST CONDITIONS VO = ± 0.5 to 2.5 V, f = 10 Hz

RL = 10 kΩ,

CL = 100 pF

MIN

TYP

1.8

2.5

UNIT V/µs

18

f = 1 kHz

8

f = 0.1 to 1 Hz

0.5

f = 0.1 to 10 Hz

0.7

Gain-bandwidth product

f = 10 kHz,

RL = 10 kΩ,

Phase margin at unity gain

RL = 10 kΩ,

CL = 100 pF

POST OFFICE BOX 655303

MAX

• DALLAS, TEXAS 75265

CL = 100 pF

nV/√Hz µV

0.6

pA/√Hz

1.8

MHz

48°

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

PARAMETER MEASUREMENT INFORMATION 2 kΩ

10 kΩ

VDD +

VDD + VI

– +

VO

– 100 Ω

VDD –

VDD – 20 Ω

20 Ω

VO

+

CL (see Note A)

RL

Figure 1. Noise-Voltage Test Circuit NOTE A: CL includes fixture capacitance.

Figure 2. Phase-Margin Test Circuit Ground Shield

VDD +

–

– VI

+

+

VO

VO

VDD – Picoammeters

VDD – CL (see Note A)

VDD +

RL

Figure 4. Input-Bias and OffsetCurrent Test Circuit NOTE A: CL includes fixture capacitance.

Figure 3. Slew-Rate Test Circuit

typical values Typical values presented in this data sheet represent the median (50% point) of device parametric performance.

Input bias and offset current At the picoamp bias current level typical of the TLC2201, TLC2201A, and TLC2201B, accurate measurement of the bias current becomes difficult. Not only does this measurement require a picoammeter, but test socket leakages can easily exceed the actual device bias currents. To measure these small currents, Texas Instruments uses a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but with no device in the socket. The device is then inserted in the socket, and a second test measuring both the socket leakage and the device input bias current is performed. The two measurements are then subtracted algebraically to determine the bias current of the device.

noise Texas Instruments offers automated production noise testing to meet individual applications requirements. Noise voltage at f = 10 Hz and f = 1 kHz is 100% tested on every TLC2201B device, while lot sample testing is performed on the TLC2201A. For other noise requirements, please contact the factory.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

21

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO

Input offset voltage

Distribution

5

IIB

Input bias current

vs Common Common-mode mode voltage vs Free-air temperature

6 7

CMRR

Common-mode rejection ratio

vs Frequency

8

VOM

Maximum peak output voltage

vs Output current vs Free-air temperature

9 10

VO(PP)

Maximum peak-to-peak output voltage

vs Frequency

11

VOH

High l High-level l output p voltage l g

vs Frequency vs High-level g output p current vs Free-air temperature

12 13 14

VOL

Low-level output voltage

Low-level vs Low level output current vs Free-air temperature

15 16

AVD

Large-signal differential voltage amplification

vs Frequency vs Free-air temperature

17 18

IOS

Short-circuit output current

vs Supply voltage vs Free-air temperature

19 20

IDD

Supply current

vs Supply voltage vs Free-air temperature

21 22

SR

Slew rate

vs Supply voltage vs Free-air temperature

23 24

Pulse response

Small signal Large signal

25, 26 27, 28

Peak-to-peak equivalent input noise voltage

0.1 to 1 Hz 0.1 to 10 Hz

29 30

Gain-bandwidth product

vs Supply voltage vs Free-air temperature

31 32

Phase margin

vs Supply voltage vs Free-air temperature

33 34

Phase shift

vs Frequency

17

VN(PP)

φm

22

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

TYPICAL CHARACTERISTICS† INPUT BIAS CURRENT vs COMMON-MODE INPUT VOLTAGE

DISTRIBUTION OF TLC2201 INPUT OFFSET VOLTAGE 10

20

8 I IB – Input Bias Current – pA IIB

Percentage of Units – %

16

408 Units Tested From 2 Wafer Lots VDD ± = ± 5 V TA = 25°C P Package

12

8

4

VDD ± = ± 5 V TA = 25°C

6 4 2 0 –2 –4 –6 –8

0 – 500

– 300

– 100

100

300

– 10 –5

500

–4

VIO – Input Offset Voltage – µV

–3

Figure 5

–1

0

1

2

3

4

5

Figure 6

INPUT BIAS CURRENT vs FREE-AIR TEMPERATURE

COMMON-MODE REJECTION RATIO vs FREQUENCY

300

120 CMRR – Common-Mode Rejection Ratio – dB

VDD ± = ± 5 V VO = 0 VIC = 0

250 IIB I IB – Input Bias Current – pA

–2

VIC – Common-Mode Input Voltage – V

200

150

100

50

0

TA = 25°C 100 VDD ± = ± 5 V 80

60 VDD = 5 V 40

20

0 25

45

65

85

105

125

10

TA – Free-Air Temperature – °C

100

1k

10 k

100 k

1M

f – Frequency – Hz

Figure 7

Figure 8

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

23

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

TYPICAL CHARACTERISTICS† MAXIMUM PEAK OUTPUT VOLTAGE vs OUTPUT CURRENT

MAXIMUM PEAK OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 6

VDD ± = ± 5 V TA = 25°C

VOM +

VOM V OM – Maximum Peak Output Voltage – V

|VOM | – Maximum Peak Output Voltage – V VOM

5

4 VOM – 3

2

1

0 0

2

4

8

6

VOM +

4

2 VDD ± = ± 5 V RL = 10 kΩ

0

–2

–4

VOM –

–6 – 75

10

– 50

|IO| – Output Current – mA

– 25 0 25 50 75 100 TA – Free-Air Temperature – °C

Figure 9

Figure 10 HIGH-LEVEL OUTPUT VOLTAGE vs FREQUENCY

10

5

VV0H OH – High-Level Output Voltage – V

V V(OPP) O(PP) – Maximum Peak-to-Peak Output Voltage – V

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY

8 TA = – 55°C 6

TA = 125°C 4

2 VDD ± = ± 5 V RL = 10 kΩ 0 10 k

100 k

1M

4 TA = – 55°C 3

TA = 125°C 2

1 VDD = 5 V RL = 10 kΩ 0 10 k

100 k

f – Frequency – Hz

f – Frequency – Hz

Figure 11

Figure 12

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

24

125

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

1M

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

TYPICAL CHARACTERISTICS† HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT

HIGH-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE

VDD

6 VDD = 5 V RL = 10 kΩ

VDD – 2

VOM V OH – High-Level Output Voltage – V

VOM V OH – High-Level Output Voltage – V

TA = 25°C VDD = 5 V VDD – 4 VDD – 6 VDD = 10 V VDD – 8 VDD – 10 VDD – 12 VDD = 16 V VDD – 14 VDD – 16 0

1

2

3

4

5

4

3

2

1

0 – 75

5

– 50

IOH – High-Level Output Current – mA

– 25 0 25 50 75 100 TA – Free-Air Temperature – °C

Figure 13

Figure 14

LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT

LOW-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 1.5

2 VDD = 5 V VDD = 10 V

VDD = 5 V VOL VOL – Low-Level Output Voltage – V

TA = 25°C VOL VOL – Low-Level Output Voltage – V

125

VDD = 16 V

1.5

1

0.5

1.25 IOL = 5 mA 1

0.75

0.5

0.25 IOL = 1 mA

0 0

2 4 6 8 IOL – Low-Level Output Current – mA

10

0 – 75

– 50

Figure 15

– 25 0 25 50 75 100 TA – Free-Air Temperature – °C

125

Figure 16

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

25

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

30°

120 VDD ± = ± 5 V RL = 10 kΩ CL = 100 pF TA = 25°C

100 AVD

50°

80

70°

60

90° Phase Shift

40

110°

20

130° 150°

0

170° 1M

– 20 10

100

1k

10 k

100 k

AVD A VD – Large-Signal Differential Voltage Amplification – dB

LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY

Phase Shift

AVD A VD – Large-Signal Differential Voltage Amplification – dB

TYPICAL CHARACTERISTICS† LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE 130

VDD ± = ± 5 V, RL = 500 kΩ

120

110 VDD = 5 V, RL = 500 kΩ VDD ± = ± 5 V, RL = 10 kΩ 100

90

80 – 75

VDD = 5 V, RL = 10 kΩ

– 50

f – Frequency – Hz

– 25 0 25 50 75 100 TA – Free-Air Temperature – °C

Figure 17

Figure 18

SHORT-CIRCUIT OUTPUT CURRENT vs SUPPLY VOLTAGE

SHORT-CIRCUIT OUTPUT CURRENT vs FREE-AIR TEMPERATURE 15

VO = 0 TA= 25°C

IIOS OS – Short-Circuit Output Current – mA

IIOS OS – Short-Circuit Output Current – mA

12

8

4 VID = – 100 mV 0

–4

–8

VID = 100 mV

– 12 0

1

2

3 4 5 6 |VDD ±| – Supply Voltage – V

7

8

VDD ± = ± 5 V VO = 0

10

5

VID = – 100 mV

0

–5 VID = 100 mV – 10

– 15 – 75

– 50

Figure 19

– 25 0 25 50 75 100 TA – Free-Air Temperature – °C

Figure 20

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

26

125

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

125

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

TYPICAL CHARACTERISTICS† SUPPLY CURRENT vs SUPPLY VOLTAGE

SUPPLY CURRENT vs FREE-AIR TEMPERATURE 1.2

1.4 1.2

1 IIDD DD – Supply Current – mA

IIDD DD – Supply Current – mA

VDD ± = ± 5 V

VO = 0 No Load

1 TA = 25°C 0.8 TA = – 55°C 0.6

TA = 125°C

0.4

VDD = 5 V

0.8

0.6

0.4

0.2

0.2

VO = VDD + / 2 No Load

0 0

1

2 3 4 5 6 |VDD ±| – Supply Voltage – V

7

0 – 75

8

– 50

– 25 0 25 50 75 100 TA – Free-Air Temperature – °C

Figure 21

Figure 22

SLEW RATE vs SUPPLY VOLTAGE

SLEW RATE vs FREE-AIR TEMPERATURE

4

4 RL = 10 kΩ CL = 100 pF TA = 25°C

3.5

SR – 3.5 SR –

3

3 SR – Slew Rate – V/ µ s

SR – Slew Rate – V/ µ s

125

SR + 2.5 2 1.5

2.5 SR + 2 1.5

1

1

0.5

0.5

0 0

1

2

3

4

5

6

7

8

0 – 75

VDD ± = ± 5 V RL = 10 kΩ CL = 100 pF – 50

|VDD ±| – Supply Voltage – V

Figure 23

– 25 0 25 50 75 100 TA – Free-Air Temperature – °C

125

Figure 24

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

27

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

TYPICAL CHARACTERISTICS VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE

VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE

100

50

140 120 VO – Output Voltage – mV VO

VO – Output Voltage – mV VO

75

160

VDD ± = ± 5 V RL = 10 kΩ CL = 100 pF TA = 25°C

25 0 – 25 – 50 – 75

VDD = 5 V RL = 10 kΩ CL = 100 pF TA = 25°C

100 80 60 40 20 0

– 100

0

1

2

3

4

5

6

– 20

7

4 1 2 3 t – Time – µs

0

t – Time – µs

Figure 25

6

7

Figure 26

VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE 5

VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE 5

VDD ± = ± 5 V RL = 10 kΩ CL = 100 pF TA = 25°C

4

2 1 0 –1 –2 –3

VDD = 5 V RL = 10 kΩ CL = 100 pF TA = 25°C

4 VO – Output Voltage – mV VO

3 VO – Output Voltage – mV VO

5

3

2

1

0

–4 –5

–1 0

5

10

15

20

25

30

35

0

40

t – Time – µs

10

15

20

t – Time – µs

Figure 27

28

5

Figure 28

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

25

30

35

40

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

PEAK-TO-PEAK EQUIVALENT INPUT NOISE VOLTAGE 0.1 TO 1 Hz 1

VDD ± = ± 5 V TA = 25°C

0.75 0.5 0.25 0 0.25 – 0.5 – 0.75 –1

0

1

2

3

4

5

6

7

8

9

10

t – Time – s

VVN(PP) µV N(PP) – Peak-to-Peak Equivalent Input Noise Voltage – uV

VVN(PP) µV N(PP) – Peak-to-Peak Equivalent Input Noise Voltage – uV

TYPICAL CHARACTERISTICS† PEAK-TO-PEAK EQUIVALENT INPUT NOISE VOLTAGE 0.1 TO 10 Hz 1

VDD ± = ± 5 V TA = 25°C

0.8 0.6 0.4 0.2 0 – 0.2 – 0.4 – 0.6 – 0.8 –1 0

1

2

4

5

6

7

8

9

10

t – Time – s

Figure 29

Figure 30

GAIN-BANDWIDTH PRODUCT vs SUPPLY VOLTAGE

GAIN-BANDWIDTH PRODUCT vs FREE-AIR TEMPERATURE

2.1

2.5 RL = 10 kΩ CL = 100 pF TA = 25°C

RL = 10 kΩ CL = 100 pF Gain-Bandwidth Product – MHz

Gain-Bandwidth Product – MHz

3

2

1.9

1.8 0

1

2 3 4 5 6 |VDD ±| – Supply Voltage – V

7

8

VDD ± = ± 5 V 2

VDD = 5 V 1.5

1 – 75

– 50

– 25

0

25

50

75

100

125

TA – Free-Air Temperature – °C

Figure 31

Figure 32

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

29

TLC2201, TLC2201A, TLC2201B, TLC2201Y Advanced LinCMOS LOW-NOISE PRECISION OPERATIONAL AMPLIFIERS SLOS021A – NOVEMBER 1988 – REVISED AUGUST 1994

TYPICAL CHARACTERISTICS† PHASE MARGIN vs SUPPLY VOLTAGE

PHASE MARGIN vs FREE-AIR TEMPERATURE

50°

50° RL = 10 kΩ CL = 100 pF TA = 25°C

VDD ± = ± 5 V 48° φm – Phase Margin om

φm – Phase Margin om

48°

46°

44°

42°

46°

VDD = 5 V

44°

42° RL = 10 kΩ CL = 100 pF

40° 0

1

2 3 4 5 6 |VDD ±| – Supply Voltage – V

7

8

40° – 75

– 50

– 25

0

25

50

75

100

125

TA – Free-Air Temperature – °C

Figure 33

Figure 34

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

APPLICATION INFORMATION latch-up avoidance Because CMOS devices are susceptible to latch-up due to their inherent parasitic thyristors, the TLC2201, TLC2201A, and TLC2201B inputs and outputs are designed to withstand – 100-mA surge currents without sustaining latch-up; however, techniques reducing the chance of latch-up should be used whenever possible. Internal protection diodes should not be forward biased in normal operation. Applied input and output voltages should not exceed the supply voltage by more than 300 mV. Care should be exercised when using capacitive coupling on pulse generators. Supply transients should be shunted by the use of decoupling capacitors (0.1 µF typical) located across the supply rails as close to the device as possible.

electrostatic discharge protection These devices use internal ESD-protection circuits that prevent functional failures at voltages at or below 2000 V. Care should be exercised in handling these devices, as exposure to ESD may result in degradation of the device parametric performance.

30

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. TI warrants performance of its semiconductor products and related software to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property or environmental damage (“Critical Applications”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI products in such applications requires the written approval of an appropriate TI officer. Questions concerning potential risk applications should be directed to TI through a local SC sales office. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Nor does TI warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used.

Copyright  1995, Texas Instruments Incorporated