wait at least for 2 seconds. CHECK: (a) Turn the ignition switch to ON and wait at least for 20 se- conds. (b) Clear DTC stored in memory. (See page DI-239 ).
CIRCUIT DESCRIPTION The P/T squib circuit (LH) consists of the airbag sensor assembly and seat belt pretensioner (LH). It causes the SRS to deploy when the SRS deployment conditions are satisfied. For details of the function of each component, see OPERATION on page RS-2 . DTC B0136/74 is recorded when an open is detected in the P/T squib (LH) circuit. DTC No.
DTC Detecting Condition
Trouble Area
Open circuit in PL+ wire harness or PL- wire harness of squib P/T squib (LH) malfunction Airbag sensor assembly malfunction
B0136/74
Seat belt pretensioner (LH) Airbag sensor assembly Wire harness
WIRING DIAGRAM See page DI-323 .
INSPECTION PROCEDURE 1
Prepare for inspection. (See step 1 on page DI-390 )
2
Check P/T squib (LH) circuit. CHECK: For the connector (on the seat belt pretensioner side) between the seat belt pretensioner (LH) and the airbag sensor assembly, measure the resistance between PL+ and PL-. OK: Resistance: Below 1 Ω
Airbag Sensor Assembly
P/T Squib (LH)
PL+
PL-
NG (+) H01016 H02141
(-)
Repair or replace harness or connector between seat belt pretensioner (LH) and airbag sensor assembly.
H02213
OK
2002 ECHO (RM884U)
Author:
Date:
497
DI-328 DIAGNOSTICS
3
-
SUPPLEMENTAL RESTRAINT SYSTEM
Check airbag sensor assembly.
P/T Squib (LH) Airbag Sensor Assembly
PL+
PLON
DLC3
CG
H01017 H02139 AB0119 H10600 H01087
DTC B0136/74
Tc H10629
PREPARATION: (a) Connect the connector to the airbag sensor assembly. (b) Using a service wire, connect PL+ and PL- of the connector (on the seat belt pretensioner side) between the seat belt pretensioner (LH) and the airbag sensor assembly. (c) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds. CHECK: (a) Turn the ignition switch to ON and wait at least for 20 seconds. (b) Clear DTC stored in memory. (See page DI-239 ) (c) Turn the ignition switch to LOCK, and wait at least for 20 seconds. (d) Turn the ignition switch to ON, and wait at least for 20 seconds. (e) Check DTC. (See page DI-239 ) OK: DTC B0136/74 is not output. HINT: Codes other than code B0136/74 may be output at this time, but they are not relevant to this check. NG
Replace airbag sensor assembly.
OK
2002 ECHO (RM884U)
Author:
Date:
498
DI-329 DIAGNOSTICS
4
-
SUPPLEMENTAL RESTRAINT SYSTEM
Check P/T squib (LH).
P/T Squib (LH) →←
Airbag Sensor Assembly
ON
DLC3
CG
DTC B0136/74
Tc
H01018 AB0119 H10600 H01087
H10630
PREPARATION: (a) Turn the ignition switch to LOCK. (b) Disconnect negative (-) terminal cable from the battery, and wait at least for 90 seconds. (c) Connect the seat belt pretensioner (LH) connector. (d) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds. CHECK: (a) Turn the ignition switch to ON, and wait at least for 20 seconds. (b) Clear DTC stored in memory. (See page DI-239 ) (c) Turn the ignition switch to LOCK, and wait at least for 20 seconds. (d) Turn the ignition switch to ON, and wait at least for 20 seconds. (e) Check DTC. (See page DI-239 ) OK: DTC B0136/74 is not output. HINT: Codes other than code B0136/74 may be output at this time, but they are not relevant to this check. NG
Replace seat belt pretensioner (LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal. To make sure of this, use the simulation method to check.
CIRCUIT DESCRIPTION. The P/T squib (LH) circuit consists of the airbag sensor assembly and seat belt pretensioner (LH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The P/T squib (LH) circuit consists of the airbag sensor assembly and seat belt pretensioner (LH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The P/T squib (LH) circuit consists of the airbag sensor assembly and seat belt pretensioner (LH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The side squib (LH) circuit consists of the airbag sensor assembly and side airbag assembly (LH). It causes the SRS to deploy when ...
The P/T squib circuit (RH) consists of the airbag sensor assembly and seat belt ... â¢Open circuit in PR+ wire harness or PR- wire harness of ... WIRING DIAGRAM.
CIRCUIT DESCRIPTION. The side squib (LH) circuit consists of the airbag sensor assembly and side airbag assembly (LH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The side squib (LH) circuit consists of the airbag sensor assembly and side airbag assembly (LH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The P/T squib (RH) circuit consists of the airbag sensor assembly and seat belt pretensioner (RH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The P squib circuit consists of the airbag sensor assembly and front passenger airbag assembly. It causes the SRS to deploy when the ...
B0101/14. Open in D Squib Circuit. CIRCUIT DESCRIPTION. The D squib circuit consists of the airbag sensor assembly, spiral cable and steering wheel pad.
B0105/53. Short in P Squib Circuit. CIRCUIT DESCRIPTION. The P squib circuit consists of the airbag sensor assembly and front passenger airbag assembly.
CIRCUIT DESCRIPTION. The side squib (RH) circuit consists of the airbag sensor assembly and side airbag assembly (RH). It causes the SRS to deploy when ...
rFSH vs hMG in antagonist prootocol: No differences. Bosch et al, 2008; Devroey et al, 2012 (Megaset). â rLH supplementation in long protocol: No differences.
CIRCUIT DESCRIPTION. The side squib (RH) circuit consists of the airbag sensor assembly and side airbag assembly (RH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The side squib (RH) circuit consists of the airbag sensor assembly and side airbag assembly (RH). It causes the SRS to deploy when ...
Short in Side Squib (RH) Circuit (to B+). CIRCUIT DESCRIPTION. The side squib (RH) circuit consists of the airbag sensor assembly and side airbag assembly ...
that the flat portion of the center opening (and on some models, arrow indentation) faces the proper letters, LH for left handed doors, RH for right handed doors.
06/2007. Cedar Rapids, IA, USA ... inside equipment. 2. Turn off or trip circuit breaker by pressing push-to-trip button ... Route wires (D) through lug cover.
