CIRCUIT DESCRIPTION. The P squib circuit consists of the airbag sensor assembly and front passenger airbag assembly. It causes the SRS to deploy when the ...
CIRCUIT DESCRIPTION The P squib circuit consists of the airbag sensor assembly and front passenger airbag assembly. It causes the SRS to deploy when the SRS deployment conditions are satisfied. For details of the function of each component, see OPERATION on page RS-2 . DTC B0106/54 is recorded when an open is detected in the P squib circuit. DTC No.
B0106/54
DTC Detecting Condition
Trouble Area
Open circuit in P+ wire harness or P- wire harness of squib P squib malfunction Airbag sensor assembly malfunction
Prepare for inspection. (See step 1 on page DI-390 )
2
Check P squib circuit. CHECK: For the connector (on the front passenger airbag assembly side) between the front passenger airbag assembly and the airbag sensor assembly, measure the resistance between P+ and P-. OK: Resistance: Below 1 Ω
P Squib Airbag Sensor Assembly
P(-) R14286 H02142
P+ (+)
NG H02251
Repair or replace harness or connector between front passenger airbag assembly and airbag sensor assembly.
OK
2002 ECHO (RM884U)
Author:
Date:
445
DI-276 DIAGNOSTICS
3
-
SUPPLEMENTAL RESTRAINT SYSTEM
Check airbag sensor assembly.
P Squib Airbag Sensor Assembly →← P-
P+
DLC3
CG
ON
Code B0106/54
Tc
H01023 H02144 AB0119 H10600 H01078
H10613
PREPARATION: (a) Connect the connector to the airbag sensor assembly. (b) Using a service wire, connect P+ and P- of the connector (on the front passenger airbag assembly side) between the front passenger airbag assembly and the airbag sensor assembly. (c) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds. CHECK: (a) Turn the ignition switch to ON and wait at least for 20 seconds. (b) Clear DTC stored in memory. (See page DI-239 ) (c) Turn the ignition switch to LOCK, and wait at least for 20 seconds. (d) Turn the ignition switch to ON, and wait at least for 20 seconds. (e) Check DTC. (See page DI-239 ) OK: DTC B0106/54 is not output. HINT: Codes other than code B0106/54 may be output at this time, but they are not relevant to this check. NG
Replace airbag sensor assembly.
OK
2002 ECHO (RM884U)
Author:
Date:
446
DI-277 DIAGNOSTICS
4
-
SUPPLEMENTAL RESTRAINT SYSTEM
Check P squib.
P Squib
→←
Airbag Sensor Assembly
ON
DLC3
CG
DTC B0106/54
Tc
H01024 AB0119 H10600 H01078
H10614
PREPARATION: (a) Turn the ignition switch to LOCK. (b) Disconnect negative (-) terminal cable from the battery, and wait at least for 90 seconds. (c) Connect the front passenger airbag assembly connector. (d) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds. CHECK: (a) Turn the ignition switch to ON, and wait at least for 20 seconds. (b) Clear DTC stored in memory. (See page DI-239 ) (c) Turn the ignition switch to LOCK, and wait at least for 20 seconds. (d) Turn the ignition switch to ON, and wait at least for 20 seconds. (e) Check DTC. (See page DI-239 ) OK: DTC B0106/54 is not output. HINT: Codes other than code B0106/54 may be output at this time, but they are not relevant to this check. NG
Replace front passenger airbag assembly.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal. To make sure of this, use the simulation method to check.
CIRCUIT DESCRIPTION. The side squib (LH) circuit consists of the airbag sensor assembly and side airbag assembly (LH). It causes the SRS to deploy when ...
B0101/14. Open in D Squib Circuit. CIRCUIT DESCRIPTION. The D squib circuit consists of the airbag sensor assembly, spiral cable and steering wheel pad.
CIRCUIT DESCRIPTION. The side squib (RH) circuit consists of the airbag sensor assembly and side airbag assembly (RH). It causes the SRS to deploy when ...
B0105/53. Short in P Squib Circuit. CIRCUIT DESCRIPTION. The P squib circuit consists of the airbag sensor assembly and front passenger airbag assembly.
The P/T squib circuit (RH) consists of the airbag sensor assembly and seat belt ... â¢Open circuit in PR+ wire harness or PR- wire harness of ... WIRING DIAGRAM.
CIRCUIT DESCRIPTION. The P/T squib (LH) circuit consists of the airbag sensor assembly and seat belt pretensioner (LH). It causes the SRS to deploy when ...
wait at least for 2 seconds. CHECK: (a) Turn the ignition switch to ON and wait at least for 20 se- conds. (b) Clear DTC stored in memory. (See page DI-239 ).
CIRCUIT DESCRIPTION. The side squib (LH) circuit consists of the airbag sensor assembly and side airbag assembly (LH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The side squib (RH) circuit consists of the airbag sensor assembly and side airbag assembly (RH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The side squib (LH) circuit consists of the airbag sensor assembly and side airbag assembly (LH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The side squib (RH) circuit consists of the airbag sensor assembly and side airbag assembly (RH). It causes the SRS to deploy when ...
Short in Side Squib (RH) Circuit (to B+). CIRCUIT DESCRIPTION. The side squib (RH) circuit consists of the airbag sensor assembly and side airbag assembly ...
CIRCUIT DESCRIPTION. The P/T squib (LH) circuit consists of the airbag sensor assembly and seat belt pretensioner (LH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The P/T squib (RH) circuit consists of the airbag sensor assembly and seat belt pretensioner (RH). It causes the SRS to deploy when ...
CIRCUIT DESCRIPTION. The P/T squib (LH) circuit consists of the airbag sensor assembly and seat belt pretensioner (LH). It causes the SRS to deploy when ...
*5 *" 5 *7 & " $ 5 *0 /. For one Command Initiative, a Big Man may. MOVE. Move up to 3D6 inches once per turn. SPOT. Spot. TASK ATTEMPT. Attempt a task ...
Jun 28, 2003 - typically from â40 to 120 °C. For temperatures typically below 200 K, the ... where ECO, EPH, ESR, α1 and µ0 are adjustable parameters, and ...
