Mar 29, 2011 - Strong Enterprises withdraws approval (SB #29) for. ARGUS AAD use in Dual Hawk Tandem, under Service Bulletin #22, dated. February 20 ...
March 29, 2011 Argus AAD, manufactured by Aviacom SA/NV use in the Dual Hawk Tandem System. Status: Mandatory. Strong Enterprises withdraws approval (SB #29) for ARGUS AAD use in Dual Hawk Tandem, under Service Bulletin #22, dated February 20, 1997. See: FAA Part 65.129(e). Identification: Dual Hawk Tandem System P/N 103000 through 103005. We do not approve the Argus AAD’s to be used in any of Strong Enterprises solo skydiving systems. Background: At least four documented instances of ARGUS AAD units have been recorded where the units have fired and the cutter failed to fully cut the reserve closing loop. These instances have been worldwide and documented with photographs of partially cut reserve loops. This failure mode subjects users to an extreme hazard and possibly death by not being able to activate the reserve parachute at all. FAA, Part 65.129 (e) states, “No certificated parachute rigger may pack, maintain, or alter a parachute in any manner that deviates from the procedures approved by the administrator or the manufacturer of the parachute.” Effective Date: March 29, 2011. Authority: Ted Strong, President Strong Enterprises 11236 Satellite Blvd. Orlando, FL 32837 US Distribution: Manufacturer, FAA, USPA, PIA Tech Comm. and Rigging Comm., Foreign Parachute Organizations, all Dual Hawk Tandem Examiners and Instructors, Dual Hawk Tandem owners on record, Parachutist, www.strongparachutes.com
Postal Address: P O BOX 181016, Dalbridge, Durban, South Africa 4014. SERVICE ... Date : March 23, 2011 Service Bulletin# PSSB0003 #Pages 2 ... installation of an Argus AAD , a parachute were to be deemed by the FAA to not be safe.
Oct 21, 2010 - Opening, Hi-performance 7-cell reserve parachute, which ... Nylon Ripstop. Suspension Line 725 lb. Spectra. Number of Cells 7. Aspect Ratio ...
Oct 21, 2010 - The Z-Po Main Canopy by Strong Enterprises is fun to fly and responds confidently to the inputs of skydivers of all skill levels. The versatility and ...
it gets to the point of becoming dangerous, and help avoid repetitive partial or complete factory ..... However, your care will determine the useful service life of the system. Always use a ... Snap or âclickâ the gates open and closed on the qui
must be returned to Strong Enterprises or an authorized Strong Enterprises Recertification. Center for any required updating and recertification. After the ...
Optional components in Italic. Qty Description ..... When closing the main container, make sure that the left jumpmaster handle extension lays on top of the side ...
Oct 20, 2011 - The manufacturer of the cutter assembly has confirmed that the failure to install the knife blade was caused by error during the cutter assembly ...
It contains explanations that will be useful to the airport security staff. ... A skydiver should always adhere to all rules and regulations set by his/her ..... you must switch OFF your Vigil® II before travelling in a closed vehicle (car, bus, tra
2.0.2.5. Close Velcro around s-folded line, making sure not to catch the line in the velcro. Mate toggle and riser. 2.0.2.6. Repeat procedure on the opposite riser.
Mar 3, 2015 - in the end and tighten as much as possible. 2.1.7. Cut the end of the cord to within. 1/4 inch of knot and burn ends to prevent fraying. Repeat for ...
Dec 1, 1990 - SERVICE BULLETIN: If the RSL lanyard does not fit properly, check the length against the chart for proper mating/compatibility. COMPLIANCE ...
Dec 1, 2003 - All Propellers, Governors, and Accumulators .... service (engine installation) or at any time governor or accumulator is removed from service.
Jun 22, 1992 - Also, it is imperative that the scale used is a calibrated scale. Failure to do so will result in false measurements and non-compliance with this ...
made only) *2. 85143-02020. 85143-02020. Grommet rear wiper motor. 1. I. Prev. Part. New Part. (I). PP. NP. NI. PP. NP. (NI). PP. NP. S Interchangeable as a set.
Aug 24, 2010 - Engineering Aspects are. FAA (DER) .... been in the combustion chamber provides a base to support the intake valve in the event the valve.
Aug 24, 2010 - Lycoming Engines has identified a specific lot of intake valves P/N .... been in the combustion chamber provides a base to support the intake ...
It is also stamped on the manufacturer's plate as shown in the ... Mainly false air intake triggered this code, which was due to improperly fitted throttle body O-ring ...
This will require a (1) time inspection and replacement of the throttle body retaining nut fastener. INSTRUCTIONS: Read entire procedure before beginning work.
Manufacturer: To issue new updated copies: 1. Technical description of the PZS â 92 rescue parachute, Packing and use instructions No. P â 003 â 93, 2. issue ...