SKU 10329 Freestanding Lace Floral Table Runner Set Instructions
invisible marking pen. (like the one on the picture) in order to make the stitching easier. The ink from such a pen will disap- pear usually after 5-10 minutes when ...
SKU 10329 Freestanding Lace Floral Table Runner Set Instructions In order to create this fine freestanding lace table runner you will need: 1. Our Freestanding Lace Floral Table Runner Set : SKU 10329 FSL Floral Table Runner Set 2. Water-soluble stabilizer suitable for freestanding lace (we prefer Vilene) 3. Suitable machine embroidery thread: We find that polyester thread is especially suitable for these designs. In order to have the stitched out embroidery look the same on both sides, we would recommend that you use the same upper thread and bobbin thread. 4. Suitable fabric of your choice (we have used linen). Since some fabrics tend to shrink, you may want to dip the fabric in water for 2 hours before using it and then dry and iron it.
Step-by-step instructions 1. Hoop the water-soluble stabilizer. Depending on the type of stabilizer you are using, you have to hoop from a minimum of 2 and up to 4 layers. Make sure it is hoped very tight. 2. Stitch out the design components. In order to prepare the table runner featured on our site, you will need to stitch 4 times the FSL floral corner and 20 times - the FSL floral border design. Carefully cut off the loose thread ends you get in the process of stitching (at the beginning or when changing thread).
3. Cut away the excess stabilizer. It will be easier to not cut the stabilizer close to the design outline from all sides. It will be enough to do this only from the sides were the pieces are to be connected like shown on the image to the right.
4. Connect the components to each other with manual stitches from the back side using the same thread you used to stitch out the designs. The places to apply the stitches are marked with red on the image:
When you are done connecting all pieces: 5. Place the connected freestanding lace components face up on top of the fabric. You can attach the lace to the fabric with pins or with temporary manual stitches. We prefer to use the second method as it usually is better at holding the lace and fabric together. If the colors of the freestanding lace and the fabric you are using are very similar you may want to trace the outline of the freestanding lace with an invisible marking pen (like the one on the picture) in order to make the stitching easier. The ink from such a pen will disappear usually after 5-10 minutes when you place the material in water of after 24
hours. Although using such pens is considered absolutely safe, if you have not used it before, we would recommend that you test it with the thread / fabric you are going to use, just to be on the safe side. 6. Stitch the freestanding lace to the fabric using machine zig-zag stitch – we used a 3 mm stitch with a density of 0.5 mm.
When you are done stitching the freestanding lace and the fabric together: 7. Cut away the excess fabric and dip the table runner in water until the stabilizer has been completely dissolved. 8. Let the table runner dry on an towel and then iron it. Congratulations! Your table runner is ready.
In order to create the Battenberg Lace Place Mat featured on our site you will need: 1. Our Freestanding Battenberg Lace Place Mat: SKU 10478 Battenberg ...
(maison mobile), l'installation doit être conforme à la norme. Manufactured .... Conduite flexible neuve en métal pour appareil électroménager. (1,3 cm [1/2 po] ...
use both arms and grasp the rear edge of range back. .... the back edge of the template against rear wall ..... Check diagonally from front to back, then level the.
not exceed 3 feet (36 inches) in length. A “T” handle type manual gas valve must be installed in the gas supply line to this appliance. 316903004 Rev A (1304).
4), ubique el soporte colo- cando el borde trasero de la plantilla contra la pared posterior y el borde lateral de la plantilla en la marca que hizo como refer-.
imate .ame length of the lower oven burner should be 1 inch with a distinct inner blue .ame. To remove the lower oven bottom, remove oven bottom hold down ...
compartments before connecting the gas and electrical supply to the ... a match. Hold a lighted match to the burner, then slowly turn the knob to the LITE position.
circuit protected by a 15 amp. circuit breaker or time delay fuse. ... The customer should have the wall receptacle and circuit .... burner valves (linear .ow).
withstand the heat generated by the range. • Do not obstruct the .ow of combustion air at the oven vent nor around the base or beneath the lower front panel of ...
WHAT TO DO IF YOU SMELL GAS: ... drawers of this range can result in serious injuries and can ... Adjust surface burner .ame size so it does not extend.
Issue: 1 16.03.2016. FUSE. 7772 / SKU 1215019. P.01 /02. LIRE ATTENTIVEMENT LES INSTRUCTIONS AVANT DE COMMENCER LE MONTAGE. CE PRODUIT DOIT ÃTRE INSTALLÃ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI. CONNAÃT BIEN LE PRODUIT ET SON
Allows a merchant to query the payment gateway and receive a copy of the gateway's current key-exchange and signature certificates. Batch administration.
Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with .... Use a mild solution of liquid household cleaner and warm water to remove ...
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are ... These words mean: .... oven door and will vary based on electric outlet receptacle.
All safety messages will tell you what the potential hazard is, tell you how to reduce the .... Do not operate range without anti-tip bracket installed and engaged.
ANSI A225.1/NFPA 501A or with local codes. Mobile home installations ... Power Cord intended to be plugged into a standard 14-50R wall receptacle. Be sure ...
To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage space located above the surface units should be avoided.
leveling leg prior to anti-tip bracket installation. WARNING. Excessive Weight Hazard. Use two or more people to move and install range. Failure to do so can ...Termes manquants :
IMPORTANT : À conserver pour consultation par l'inspecteur local des installations électriques. .... The Tech Sheet is located on the back of the range inside a .... B. Floor Mounting. Wall Mounting. A. B. A. #12 x 15/8" screws. B. Anti-tip bracket.
