• Resistance Tolerance E: ±3%, F: ±1% • Thermal Time Constant: Approx. 7.0 sec • Lead wires cut variation and taping type (Standard Type) is available Note 1: When measured at 25°C, in still air, as a single unit without mounting Note 2: Permisssive Operating Current raises Thermistor’s temperature by 1°C. The current less than 1/10 of the Permissive Operating Current value is recommended. Note 3: NTC Thermistor’s temperature rises about 10°C by self heating at 25°C in still air when Rated Electric Power is applied.
RESISTANCE TOLERANCE VS. TEMPERATURE
TEMPERATURE TOLERANCE VS. TEMPERATURE
Resistance Tolerance ±1% at 25°C
Resistance Tolerance ±1% at 25°C Temperature Tolerance (±°C)
Resistance Tolerance (±%)
3.0 5 4 3 2 1 0 –40
0
50 Ambient Temperature (°C)
100
125
2.0
1.0
–40
0
50 Ambient Temperature (°C)
100
Above graph expresses tolerance of resistance and temperature against a center value at each ambient temperature. According to above graph, NTH4G with resistance tolerance ±1% at 25°C provides temperature detection within ±2°C between –40°C and +125°C.
CG01-J
561
THERMISTOR PRODUCTS
THERMISTOR PRODUCTS NTC THERMISTOR LEADED FOR TEMPERATURE SENSING
THERMISTOR PRODUCTS NTC THERMISTOR LEADED FOR TEMPERATURE SENSING
Meritek NTC Power Thermistor (SCK) devices are made of a specially formulated metal oxide ceramic material which is capable of suppressing high inrush ...
Jan 4, 2007 - When a current flows through a thermistor, it will generate heat which will raise the ... The rate of transfer is well described by Newton's law of.
to room temperature calibration, the sensor accuracy .... For the most current package drawings, please see the Microchip Packaging ..... Philippines - Manila.
Dégagez le haut du couvercle du l'équerre centrale et des supports intermédiaires. Voir la Figure 4. 5. Si les fils doivent entrer ou passer par le chemin de câble, ...
wall when installing) Secure the box to the stud using two screws (not included) as shown in Figure 2. 2. Run power supply cable through cable clamp (previously installed) leaving approximately 6 inches (152 mm) of wire. TO PREVENT POSSIBLE DAMAGE TO
degrees so that the back box will be square with the joist after installation. ...... dans toute ouverture d'admission ou d'évacuation, car cela peut causer une ...
Sep 13, 2006 - 80. 0.1593. 0.92. - 2.81. 318.6. 85. 0.1377. 0.99. - 2.73. 275.5. 90 ..... not designed for use in medical, life-saving, or life-sustaining applications.
Failed damper system may be stuck in recirculation mode. Check defrost damper. If damper is always blocking incoming fresh air, have contractor verify damper ...
returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement ...
Selecting the recirculation settings. Only to be used after the appliance is installed in a recirculation application. Sélection des paramètres de recirculation.
the electronic plasma frequency (fpe) and the electronic cyclotron frequency .... coordinate system, the magnetic field exhibits the poloidal mode polarization of.
even during routine maneuvers like turning, or driving on hills or over obstacles, if you fail to take proper precautions. Read and understand your owner's manual ...
2.2. Pc5 Pulsations. [9] Figure 3 presents measurements from the Fluxgate. Magnetometer (FGM) instruments [Balogh et al., 2001] on board the 4 spacecraft in ...
Le produit doit être appliqué, sur la surface sèche, préférablement à l'aide d'un pulvérisateur, ou avec un pinceau aplati. Le produit doit être appliqué dans une ...