Installing the sensor with the Jetmobile MicrDIMM levels 3 & 4
MicrDIMM 4.0 Magnetic Ink Toner Cartridge Detection and Keylock activation
Installation Guide for HP LaserJet P3005 Edition 1 March 2007
©1994-2007 Jetmobile
INTERNAL DOCUMENT - CONFIDENTIAL THIS GUIDE IS ONLY TO BE USED BY TRAINED JETMOBILE VARs AS A REFERENCE MANUAL COMPLEMENTING A TRAINING.
MicrDIMM Sensor Installation process for hp LaserJet P3005
ã2007 Jetmobile
Page intentionally left blank
© 1994-2007 Jetmobile. All rights Reserved Jetmobile is a registered trademark of JetCAPS International Business Strategy SA All other trademarks are the property of their respective owners. THIS DOCUMENT IS NON CONTRACTUAL. JETMOBILE RESERVES THE RIGHT TO ADD, REMOVE OR MODIFY ANY FUNCTIONALITY OF THE CURRENT PRODUCT AT ANY TIME WITHOUT ANY PRIOR NOTICE. Jetmobile S.A.S 89 rue du Gouv.Gal Eboué 92130 Issy Mx FRANCE
WEB: http://www.jetmobile.com SUPPORT & INFORMATION: http://www.jetmobile.com http://www.cmc7.com
Page 2
MicrDIMM Sensor Installation process for hp LaserJet P3005 ã2007
Jetmobile
I - Sensor Installation To install the Jetmobile MicrDIMM sensor, please follow the different steps carefully, in the correct order. JETMOBILE IS NOT RESPONSIBLE OF ANY DAMAGE YOU COULD CAUSE TO THE PRINTER OR TO YOURSELF WHEN INSTALLING THE SENSOR. JETMOBILE RECOMMANDS THAT YOU FIRST READ ALL THE STEPS CAREFULLY BEFORE STARTING THE INSTALLATION.
1. Switch the printer OFF, unplug the power cable and any other connection (network cable …). WARNING: Hazardous voltages are present in the printer. It is mandatory to unplug any power cable from the printer, before starting the installation.
WARNING: If the printer was ON, it is important to wait 10 minutes before starting the installation, because some printer parts may be hot.
2. Open the front cover and remove the toner cartridge.
Page 3
MicrDIMM Sensor Installation process for hp LaserJet P3005
ã2007 Jetmobile
3. Remove the right side cover.
4. Remove the screw on the up right corner, remove the plate and remove the small top cover of the printer to the back by sliding.
Page 4
MicrDIMM Sensor Installation process for hp LaserJet P3005 ã2007
Jetmobile
5. Slide the cabling between the top cover and the control panel cover.
6. Put the dual-side adhesive tape on the sensor (on the totally flat side), and fix it firmly in the area indicated as shown above. Please make sure the sensor is correctly positioned so that its square window looks upside down and clean both surfaces with alcohol before applying the adhesive tape. 7. You will need to put the reflective white sticker on the exact same position on the MICR toner cartridge so that it faces the sensor.
Page 5
MicrDIMM Sensor Installation process for hp LaserJet P3005
ã2007 Jetmobile
8. The sensor is now ready to be used. The last step is to connect the sensor to the MicrDIMM USB stick device , and insert that MicrDIMM USB stick I/O in one of the USB slots. Now that the sensor is installed, put back the top covers, back then side covers.
Page 6
MicrDIMM Sensor Installation process for hp LaserJet P3005 ã2007
Jetmobile
II – MICR Toner label position for LJP3005
The sensor detects a reflective white label on the toner cartridge, therefore differentiating it from a regular toner cartridge.
Jetmobile does not provide toner, but recommends the following: -
use high quality MICR toner and check paper only, to ensure a good toner adhesion and limit risks of toner removal. only use new cartridges, and not remanufactured and even less recycled cartridges, as a perfect toner cartridge is mandatory to keep checks printing quality. Position the label at the exact required location, a large label is better than a small label. A reflective paper is better than a mat paper.
Page 7
MicrDIMM Sensor Installation process for hp LaserJet P3005
ã2007 Jetmobile
III - Keylock Installation To install the Jetmobile MicrDIMM keylock, please follow the different steps carefully, in the correct order. JETMOBILE IS NOT RESPONSIBLE OF ANY DAMAGE YOU COULD CAUSE TO THE PRINTER OR TO YOURSELF WHEN INSTALLING THE KEYLOCK. JETMOBILE RECOMMANDS THAT YOU FIRST READ ALL THE STEPS CAREFULLY BEFORE STARTING THE INSTALLATION. 1. Switch the printer OFF, unplug the power cable and any other connection (network cable …). WARNING: Hazardous voltages are present in the printer. It is mandatory to unplug any power cable from the printer, before starting the installation.
WARNING: If the printer was ON, it is important to wait 10 minutes before starting the installation, because some printer parts may be hot.
2. Open the right side cover and remove the formatter door. 3. Take the 4 parts for the keylock (keylock, EIO plate, nut, keylock cover) and assemble them as per the following picture:
Page 8
MicrDIMM Sensor Installation process for hp LaserJet P3005 ã2007
Jetmobile
4. Remove a free EIO slot plate, and make sure you keep the two screws at hand. Then insert the EIO plate as per the following picture:
When the plate is installed fix it with the two screws that were fixing the free EIO slot plate.
5. Disconnect the sensor from the MicrDIMM CompactFlash, connect the keylock cable to the sensor cable by detaching the black loop connector and attaching the keylock, reconnect the sensor to the MicrDIMM CompactFash.
_________________________________
Page 9
