Installing the sensor with the Jetmobile MicrDIMM levels 3 & 4
MicrDIMM 3.2 Magnetic Ink Toner Cartridge Detection and Keylock activation
Installation Guide for HP LaserJet 2410/2420/2430 Edition 1 December 04
©1994-2004 Jetmobile
INTERNAL DOCUMENT - CONFIDENTIAL THIS GUIDE IS ONLY TO BE USED BY TRAINED JETMOBILE VARs AS A REFERENCE MANUAL COMPLETING A TRAINING.
MicrDIMM Sensor Installation process for hp LaserJet 2400 2004
Jetmobile
Page intentionally left blank
© 1994-2004 Jetmobile. All rights Reserved Jetmobile is a registered trademark of JetCAPS International Business Strategy SA All other trademarks are the property of their respective owners. THIS DOCUMENT IS NON CONTRACTUAL. JETMOBILE RESERVES THE RIGHT TO ADD, REMOVE OR MODIFY ANY FUNCTIONALITY OF THE CURRENT PRODUCT AT ANY TIME WITHOUT ANY PRIOR NOTICE. Jetmobile S.A.S 89 rue du Gouv.Gal Eboué 92130 Issy Mx FRANCE
WEB: http://www.jetmobile.com SUPPORT & INFORMATION: http://www.jetmobile.com http://www.cmc7.com
Page 2
MicrDIMM Sensor Installation process for hp LaserJet 4200 & 4300 2004
Jetmobile
I - Sensor Installation To install the Jetmobile MicrDIMM sensor, please follow the different steps carefully, in the correct order.
JETMOBILE IS NOT RESPONSIBLE OF ANY DAMAGE YOU COULD CAUSE TO THE PRINTER OR TO YOURSELF WHEN INSTALLING THE SENSOR. JETMOBILE RECOMMANDS THAT YOU FIRST READ ALL THE STEPS CAREFULLY BEFORE STARTING THE INSTALLATION. 1. Switch the printer OFF, unplug the power cable and any other connection (network cable …). WARNING: Hazardous voltages are present in the printer. It is mandatory to unplug any power cable from the printer, before starting the installation.
WARNING: If the printer was ON, it is important to wait 10 minutes before starting the installation, because some printer parts may be hot.
2. Open the front cover and remove the toner cartridge.
Page 3
MicrDIMM Sensor Installation process for hp LaserJet 2400 2004
Jetmobile
3. Remove the two screw on each side to remove both panels
4. Remove the two screws from the back panel then remove it
Page 4
MicrDIMM Sensor Installation process for hp LaserJet 4200 & 4300 2004
Jetmobile
5. On the back of the printer, slide to the right the vertical plastic cache in order to remove it.
6. Remove the screw holding the small top cover.
Page 5
MicrDIMM Sensor Installation process for hp LaserJet 2400 2004
Jetmobile
7. Remove the small top cover of the printer to the back by sliding it.
8. Remove the four screws maintaining the top cover, then remove it.
Page 6
MicrDIMM Sensor Installation process for hp LaserJet 4200 & 4300 2004
Jetmobile
9. The sensor must be installed on the right side of the printer (when you are facing the back of the printer) as shown on the picture.
The sensor cable must be routed from the right to the left using the cable guides on the back plastic. Please make sure the sensor is correctly positioned so that it faces the white label on the MICR toner cartridge. 10. The sensor is now ready to be used. The last step is to connect the sensor to the MicrDIMM CompactFlash, to insert that MicrDIMM CompactFlash in one of the CF slots. Now that the sensor is installed put back the top covers, back then side covers.
Page 7
MicrDIMM Sensor Installation process for hp LaserJet 2400 2004
Jetmobile
II – MICR Toner label position for LJ2410/2420/2430
The sensor detects a white label on the toner cartridge, therefore differentiating it from a regular toner cartridge.
Jetmobile does not provide toner, but recommends the following: -
Page 8
use high quality MICR toner and check paper only, to ensure a good toner adhesion and limit risks of toner removal. only use new cartridges, and not remanufactured and even less recycled cartridges, as a perfect toner cartridge is mandatory to keep checks printing quality.
MicrDIMM Sensor Installation process for hp LaserJet 4200 & 4300 2004
Jetmobile
III - Keylock Installation To install the Jetmobile MicrDIMM keylock, please follow the different steps carefully, in the correct order.
JETMOBILE IS NOT RESPONSIBLE OF ANY DAMAGE YOU COULD CAUSE TO THE PRINTER OR TO YOURSELF WHEN INSTALLING THE KEYLOCK. JETMOBILE RECOMMANDS THAT YOU FIRST READ ALL THE STEPS CAREFULLY BEFORE STARTING THE INSTALLATION. 1. Switch the printer OFF, unplug the power cable and any other connection (network cable …). WARNING: Hazardous voltages are present in the printer. It is mandatory to unplug any power cable from the printer, before starting the installation.
WARNING: If the printer was ON, it is important to wait 10 minutes before starting the installation, because some printer parts may be hot.
2. Open the right side cover and remove the formatter door. 3. Take the 4 parts for the keylock (keylock, EIO plate, nut, keylock cover) and assemble them as per the following picture:
Page 9
MicrDIMM Sensor Installation process for hp LaserJet 2400 2004
Jetmobile
4. Remove a free EIO slot plate, and make sure you keep the two screws at hand. Then insert the EIO plate as per the following picture:
When the plate is installed fix it with the two screws that were fixing the free EIO slot plate.
5. Disconnect the sensor from the MicrDIMM CompactFlash, connect the keylock cable to the sensor cable by detaching the black loop connector and attaching the keylock, reconnect the sensor to the MicrDIMM CompactFash.
_________________________________
Page 10
