MAKE SURE LEDTask AMPERAGE DOESN'T EXCEED ... - GM Lighting
negative (-) side of the wire to the negative (-) side of the 24VDC power supply. (1 LARC5-PS LightBar to power supply connector included). Connecting 2 or ...
4003654 CONFORMS TO ANSI/UL STD 2108 CERTFIED TO CAN/CSA C22.2 No. 250.0.
*MAKE SURE LEDTask AMPERAGE DOESN’T EXCEED POWER SUPPLY* Make all connections and test system before installing *Use only with a 24 VDC, Class 2 power unit* SUITABLE FOR UNDER-CABINET MOUNT (PEUT ETRE FIXE SOUS UNE ARMOIRE)
LEDTask™ LARC5 24VDC LED LightBar Series Installation Instructions
Connecting to Power Supply: plug in the LARC5-PS LightBar to power supply connector into the LARC5 LED LightBar (Fig 2). Connect the positive (+) side of the wire from the connector (denoted red)(FIG 5) to the positive (+) side of the 24VDC power supply. Connect the negative (-) side of the wire to the negative (-) side of the 24VDC power supply. (1 LARC5-PS LightBar to power supply connector included) Connecting 2 or more LARC5 LED series LightBars together: a. Directly connecting LightBars: LightBars plug together using the integral connector (Fig 2). b. Connecting LightBars using flexible LightBar to LightBar connectors using the LARC5-BB-
series connectors (Fig 3).
Surface Mount: Make sure the mounting surface is clean and free from any oil. Remove the red plastic to expose double stick tape on back of LightBar (Fig 1) and gently press into place. Surface mount clips can also be used. Secure the clips to the mounting surface with the enclosed screws and snap the bar into place. Fig 4.
Fig 2
FIG 1
FIG3
FIG 4
FIG 5
9830 W. 190th St. • Unit F • Mokena, IL 60448 • Toll-Free: (866) 671-0811 • FAX: (708) 478-2640 • www.gmlighting.net Larc5_062014
Question: After changing the new toner, it still shows "Replace Toner", "Toner Low" or "Toner. Ended". Answer: Please try the following steps: a. Make sure the ...
adaptador para tuberÃa PVC o ABS de 3 y 4 pulg. (39223 y 39224). Las válvulas de admisión de aire Sure-VentMR permanecen cerradas hasta 20 psig de presión positiva, evitando la fuga durante la limpieza de la lÃnea a baja presión. Sure-Vent® 6
Caution: Excessive wrench torque, closing the gap between the bushing flange and mating hub, or the use of lubricants will break the mating hub. P-5070-TBW ...
erly connected to metal parts of the car's body. The ground ..... Connexions lors de l'utilisation du fil d'entrée .... sez pas des pièces telles que des vis supplé-.
oppure un autobus, controllare la tensione della batteria. ⢠Se l'impianto stereofonico della vettura viene la- sciato in funzionamento per un lungo periodo di.
Step 5. Thread the extension leads through the wire pass hole and securely mount the exit sign backplate to the J-box. Snap the exit frame onto the backplate.
1 mars 2016 - ... pneus admissibles entre le 1er mars 2016 et la fin de la promotion du 31 mai 2016. Un coupon postal par facture. Les rabais ci-dessus sont en vigueur à l'achat de quatre pneus. Les rabais sont offerts proportionnellement par pneu Ã
haut-parleurs, le circuit de protection coupe l'alimentation de ...... 178-184 Boundary Road, Braeside, Victoria 3195, Australia. TEL: (03) 9586-6300. PIONEER ...
Before commencing installation or maintenance, ensure electricity is switched off at the mains. 1. Fit the mounting bracket in the required position. Be aware of ...
T. I N. G. HINKLEY. English. Spanish. French. HINKLEY LIGHTING. 33000 Pin .... Connect ground wire to mounting strap (1) using green ground screw (GS). 4.
After screws are removed, lift the top of the fixture (T) upward and off of ..... caulk or sealant be put under the ball knobs used to mount fixture â see Drawing. 2.
shop catering to foreign cars.) Two holes have been drilled and tapped directly opposite each other near one end. Thumb screws are turned into these holes ...