RECOMMENDED AIR SPRING PRESSURE psi 25 30 35 40 45 50 60 70 80 105
bar 1.7 2.1 2.4 2.8 3.1 3.4 4.1 4.8 5.5 7.2
DIAL Foam
Slot SCH
RAD ER
Seal Pin
MINIMUM - 20 psi, 1.4 bar MAXIMUM - 120 psi, 8.3 bar
REBOUND DIAL - 24 Clicks Total
Turn in "+" direction for more damping and slower rebound speed. Turn in "-" direction for less damping and faster rebound speed. Count clicks out from fully closed (clockwise) when setting.
BUMP THRESHOLD KNOB - 22 Clicks Total
The blue bump threshold knob controls the internal inertia valve which automatically opens and closes the fork's compression damping circuit. You can set the sensitivty to what size bump opens the circuit and starts fork travel. Count clicks out from fully closed (clockwise) when setting.
RECOMMENDED AIR SPRING PRESSURE psi 80 85 90 100 110 120 130 145 160 170
bar 5.5 5.9 6.2 6.9 7.6 8.3 9.0 10.0 11.0 11.7
RIDER WT RANGE
FORK SIZE
BIKE SIZE
►66 66--79 79-88 88+
SOFT STANDARD FIRM X-FIRM
PT/SM MD LG XL
►145 145 - 175 175-195 195+
FWD
FORK NEGATIVE SPRING GREEN BLUE RED BLACK
If you set 10 psi lower air pressure than recommended, a softer negative spring should be installed. If you set 20 psi higher air pressure than recommended, a firmer negative spring should be installed.
C LO UN
KE
D
REBOUND KNOB - 14 Clicks Total (2 ¾ Turns of adjustment) Turn in "+" direction for more damping and slower rebound speed. Turn in "-" direction for less damping and faster rebound speed. LOCKOUT LEVER
The Lockout lever on top of the fork enables you to lock and unlock fork travel. Rotate the lever completely to the LOCKED (no travel) or the UNLOCKED (free travel) position.
MINIMUM - 50 psi, 3.4 bar MAXIMUM - 225 psi, 16.0 bar ADER
SCHR
VALVE CAP
Sloping Top Tube
For Cannondale Owner's Manual and Supplements visit our TECH CENTER : www.cannondale.com/bikes/tech/
NUT
CAUTION: When setting air pressures, clean valve & pump end before attaching . • Observe pressure range. • Replace the valve cap.
LEFTY SPEED CARBON
Creates a generous stand-over height and saves weight by using less material and fewer weld joints. The huge bend radius combined with a large shock mount also provides better load distribution—again, saving weight with less material.
Swingam Hot Box
Borrowed from its Prophet brother, the welded, hollowcore Hot Box swingarm pivot delivers superior light-weight stiffness for efficiency and improved tracking.
Turn in "+" direction for more damping and slower rebound speed. ... The blue bump threshold knob controls the internal inertia valve .... For detailed adjustment ...
jp.physoc.org. Downloaded from J Physiol ( ... with zero-power rigid gas-permeable contact lenses. .... that the Rmax following adaptation was smaller than the.
A four pipe exhaust system reduces the net exit area to 32.36 square inches, while a two-pipe system reduces the net exit area to 37.19 square inches. For the ...
corrected directly in the NC code program. The generalisation of the methodology can be applied to any surfaces and integrated in the development of a ...
REMOVE DIRECT CLUTCH SPEED SENSOR. (a) Disconnect the connector. (b) Remove the bolt and direct clutch speed sensor. (c) Remove the O-ring from the ...
Debunking Speed Bunk. By Joseph ... "The highest probable speed that an airplane can attain in ... figures in the table, and to offer some food for thought for.
case, repeat the procedure by slowing an additional few knots. If the nose drops as soon as you re- lax the back stick, you're outside the band. This nose-drop is ...
A few switch clicks or wheel turns nail the desired airspeed in some, but in others it ... plot which is the relationship between longitudinal stick force and airspeed.
531 articles. The direction of motion that yielded the largest response was termed the. 'preferred' direction, and the direction opposite to the preferred was.
best way to get additional speed, and the faster the airplane, the more important .... and then sanding the trailing edge to a radius. ..... right front cylinder, but is not done for the other two because their exhaust ports are âbetweenâ the cyl
Surface plate temperature regulated by an infinitely adjustable control with a total of 1400 watts available for drying. Laboratory hot plate - model A-100 ...
The LM715 is a high speed high gain monolithic operation- al amplifier intended for use in .... dB. Rejection. (Note 4). (Note 4). PSRR. Power Supply. RS s 10 kX. 45. 300. 45. 400. mV V ... Wide Band Video Amplifier Drive. Capability with 75X ...
trol system that prevents the eleva- tor from returning to .... control system friction hold the ele- vator at its .... Learn more about handheld GPS units with our free ...
60.8 Conclusions ... High-speed trains were introduced in the early 19th century when British engineers ... (200 mph) and has been tested at a sustained speed of 515 kph (330 mph) [12,21]. ... tion of major western European cities (Paris, Brussels, C
power, the power-assisted steering pump,. â the high level .... cylinder bank 1 below the mechanical fuel pump. It picks up .... and fuel using hand vacuum pump.
Believe me, I've cracked a few. I have even heard them say to be careful with enriching the mixture too quickly as the cold fuel will tend to crack the cylinder.
