Your new GE icemaker water filter comes complete with all the necessary hardware for installation. Each filter gives you up to six months of great-tasting water. Filter should be changed after 6 months of use. REQUIRED TOOLS FOR INSTALLATION
OPTIONAL TOOLS FOR INSTALLATION
• a tube cutter • a knife • a bucket or pan
• a file • sandpaper System is Tested and Certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor and Particulate Class V.
Do not use where water is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
WARNING
Small parts remaining after the installation could be a choke hazard. Discard safely.
The GXRTDR has been tested and Certified by WQA according to CSA B483.1.
SPECIFICATIONS • This System has been tested according to NSF/ANSI 42 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42. • Actual performance may vary with local water conditions. Model GXRTDR
à bien placer le joint dans la rainure du corps de filtre. Visser le corps de filtre; puis inspecter pour rechercher des fuites. Les cartouches de filtration contiennent.
1 Claims for arsenic reduction shall only be made on water supplies maintaining detectable residual free chlorine at the reverse osmosis (RO) system inlet.
Si les instructions contenues dans ce manuel ne sont pas ...... H. Robinet de sectionnement manuel ...... Detección de Falla a Tierra (GFCI) en receptáculos de.
the current Propane (LP) Installation Code, CAN/CGA. B149.2 ... codes, in accordance with the National Electrical Code ...... LISTE DE VÉRIFICATION POUR.
If the hard piping method is used, you must carefully align the ... standard three.prong grounding wall receptacle to ... Skip this step if oven doors are in place.
affecting burner operation, seal all openings in floor under ..... Slide front cylinders up to access front leveling legs. Be careful not to damage cylinder. □ Use the ...
accordance with the National Electrical Code (ANSI/. NFPA 70, latest ...... INSTALLATION TIP: First remove ... the center of the valve stem to engage set screw.
the gas burners resulting in fire or explosion hazard. ..... (6.4 mm) thick flame.retardant millboard ..... pressure test the gas supply system of the residence,.
of Pipes or wires. Plumbing ... codes.) ⢠Water connection is on the left side of the dishwasher. Install the hot water inlet line, using no less than ... and lay it on its back. NOTE: Do ... additionnel avec raccord 5/8 ou 7/8 po (D.I.) et d'une l
Remove house fuse or open circuit breaker before beginning ... Route house wiring as close to the installation location as ... Wire nuts. Phillips and flat-blade.
New construction installation with 25” deep openings ..... Both door faces should be 7/8” behind the front face of surrounding cabinets on either a stainless.
path of least resistance for electric current. This appliance uses a cord having an equipment- grounding conductor and a grounding plug. The plug must be ...
If the flames blow away or flutter from the burner, close the air shutter more than the original setting. The air shutter for the bake burner is accessible by removing ...
where it could be exposed to water or weather. • To reduce the ... Service information and the wiring diagram are located at the access ..... B. Connect the neutral (white) line to the center of ..... NOTE: Do not use washer cover to lift the unit. 2
20.amp circuit breaker or time delay fuse. NOTE: Use of automatic, wireless, ..... box end wrench to loosen and remove and replace the broil orifice. D. Reverse ...
Phillips #2 Screwdriver. Saber Saw. Carpenter .... NPT internal thread of the house shut.off valve, taking care to ..... T.15 and #2 Phillips screwdrivers. â¡ Drill with ...
TO REDUCE THE RISK OF FIRE, USE ONL< METAL DUCTWORK. WARNING: TO ..... Route house wiring as close to the installation location as possible, in the ...
If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Installation must be ...
Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installation must conform with the current. Natural Gas Installation Code, CAN/CGA.B149.1 or.
Set the microwave upright, being careful not to bend the front flange. Remove the one existing screw from the left side of the microwave oven. As indicated on ...
If you received a damaged dishwasher, you should immediately contact your ... Skill Level â Installation of this dishwasher requires ..... it on its back. Figure I.
Failure to follow these instructions can result in death, .... The unit will project forward, slightly beyond adjacent cabinetry ..... The wall bracket will be attached to.