13☉. Spray Assembly 14☉. Metal Handle Assembly-Cold 15.1. Handle Cap-Cold
Fixtures
☉
15.2. Handle Cap-Hot
Ensamblaje de manija metálicas-frío
0097909
Ensamblaje de manija metálicas-caliente
0097908
Tapón-frío
0094252
Tapón-caliente
0094251
Tornillos Juego de cartucho de compresiòn-frío
0090700 0098689
Juego de cartucho de compresiòn-caliente Arandela Asiento Tuerca de unión y contratuerca (2 par)
0098688 0090331 0090161 0097800
Ensamblaje de vertedor Aireador Empaque circular Cambiador de flujo Ensamblaje de soporte del rociador
0098261 0091572 0092730 0094090 0094100
Ensamblaje del rociador Ensamblaje de manija metálicas Tapón-frío
0098360 0098829 0094446
Tapón-caliente
0094445
Shaded items are available as warranty parts only Les items soulignés sont disponible seulement comme les pièces sous garantie Los articulos sombreados son disponibles solamente como piezas en garantia
Replacement parts, call : / Les pièces de rechange, appellez : / Partes de reemplazo, llame :1-888-648-6466
www.gerberonline.com
42-116-I/11-12.01
Fixtures
Available in all finishes above ☉ Disponible dans tous les finis susmentionnés ☉ Disponible en todos los acabados
8☉. 9☉. 10. 11. 12☉.
Assemblage de manette en métal -froid Assemblage de manette en métal -chaud Capuchon de la manette-froid Capuchon de la manette-chaud Vis Assemblage de cartouche à compression-froid Assemblage de cartouche à Rondelle Siège Écrou de raccord et écrou de blocage (2 paire) Assemblage du bec Brise-jet Joint torique Inverseur Assemblage du support de douchette Assemblage d’arroseur Assemblage de manette en métal Capuchon de la manette-froid Capuchon de la manette-chaud
Viega® PEX Crimp Supply Adapter. Zero Lead ManaBloc® Supply Connection. *Zero Lead identifies Viega® products meeting the lead free requirements of NSF 61-G through testing under. NSF/ANSI 372 (0.25% or less maximum weighted average lead content). Th
may be partially visible in one. 3. Press the sleeve with an appropriately sized press tool. DO NOT PRESS TWICE. Refer to the current. Viega PEX Water Systems Installation Manual for additional pressing instructions. 4. Ensuring the sealing element (
NFPA 54 or CAN/CGA-B149) and the National Electric Code (ANSI C1-NFPA 70). 5. ... If, after completing Steps 9 through 14, it is believed sufficient combustion air is ... The pilot vent plug is located on the front cover of this installation manual.
The damper is installed in the vent and as close to the draft hood as practical. ... circuits in this product are designed not to override the existing limit and safety ...
Apply one or two turns of PTFE tape to thread of push-in fitting. ... CUNO Incorporated, a 3M Company, warrants that this product is free from defects in materials ...
Power open, power close â extends product life. Reduced ..... Use 1/2 inch sheet metal screws or pop rivets. .... install a non-power stealing type of thermostat.
recognized standard, or a masonry or concrete chimney lined with a lining material ... or in the absence of local codes, to the National Fuel Gas Code, ANSI Z223.1 or ..... le clapet ne s'ouvre pas, le circuit de commande du brûleur n'est pas mis ..
of gas appliances and automatic vent damper devices, who is experienced in such ... not available, refer to local codes, or in the absence of local codes, to the ...
Abra las válvulas de corte y espere 2 o. 3 minutos para que la presión del sistema se iguale antes de poner en marcha la bomba. 9. Eliminación. La eliminación ...
For ABS drains, use NO oil base compounds! ⢠Unscrew flange and remove washer from drain assembly. ⢠If necessary, apply putty or sealant to bowl under the washer to assure seal. ⢠With the nut, follower, and mac washer at their lowest position
wholesaler or dealer, or by calling or writing Sterling, Consumer Services, 444 Highland Drive, Kohler,. Wisconsin 53044, 1-800-783-7546. TO THE EXTENT ...
Trim Cap. Capuchon de garniture Tapa ornamental. 4. Lock Nut. Ãcrou de blocage. Contratuerca. 5. Ceramic Disc. Cartouche à disque en Cartucho de disco.
IAPMO/cUPC. ⢠ICC/ANSI A117.1. ⢠EPA/Watersense. ⢠Comprend un actionneur par pression 50/50 GA505219P avec capuchon assorti et raccord droit noir.
Architecte Ingénieur. Nom de travail. • Finitions en chrome ou en nickel brossé. • Installation de trois trous. • Drain en 50/50. • Aérateur à régulation de pression ...
Anneau de friction. 1. 8. 9. 6 ... l'orifice sur le dessus de la sangle de tige de levage (3). Serrer à ... desagüe. Enlever la rondelle de caoutchouc (2), l'anneau de.
soldering and will result in the warranty being void on these parts. Cover your drain to avoid losing parts. CONSEJOS DE SEGURIDAD. Advertencia: Si usa ...
Antes de la instalación, consulte las exigencias del código local de plomería. El producto es ... abra el suministro del agua para remover cual- quier desecho ...