FCC INFORMATION This device complies with Part ... - UserManual.wiki
1. This device may not cause harmful interference, and 2. This device must accept any ... instructions, may cause harmful interference to radio communications.
FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body. Avis d’Industrie Canada: Cet appareil est conforme à la norme CNR-210 des règlements d’Industrie Canada. Son fonctionnement est sujet aux deux conditions suivantes: 1) Cet appareil ne doit pas provoquer d’interférences et 2) Cet appareil doit accepter toutes les interférences, y compris celles pouvant entraîner son dysfonctionnement. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and. (2) This device must accept any interference received, including interference that may
This device complies with Part 15 of the FCC Rules. ... Caution: Any changes or modifications not expressly approved by the party responsible for compliance.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
Firstech, LLC. | 2. QUICK START CARD. 1 WAY 4 BUTTON REMOTES. If you have an alarm and optional LED(s) installed, it will flash once a second if armed.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
FCC/IC Notices. This device complies with Part 15 of FCC. Rules and RSSÐGen of IC Rules. Operation is suEMect to the following two conditions: (1) this device may notcauseäinterference, and. (2) this device must accept any interference, including
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
This device complies with Industry Canada licence-exempt RSS standard(s). Operation ... (e.i.r.p.) is not more than that necessary for successful communication.
Changes or modifications not expressly approved by the party responsible for compliance could void the ... user's manual in accordance FCC & IC requirements.
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and. (2) this device must accept any inte
NOTE:The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could ...
This device complies with Part 15 of the FCC Rules. Operation ... to this unit not expressly approved by the party responsible for compliance could void the user's.
This device complies with Part 15 of the FCC Rules / Industry Canada ... If this equipment does cause harmful interference to .... 5.1The Module physical map. 6.
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits ... compliance could void the user's authority to operate the equipment. This device ...
undesired operation of the device."2.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to ...
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouil
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For vehicles ...
Smart LF Oscillator Model TMLF12-4. FCC ID: NI4TMLF12-4. For vehicles sold in U.S.A.: NOTE. This device complies with part 15 of the FCC Rules. Operation is ...
exposure compliance. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter. The portable device is designed ...