This specification applies to the electret condenser microphone outlined within this document. Model Number: I.
MB6022ASC-1
Electrical Characteristics ITEM
Test Condition (Vs= 2.0 V, RL= 2.2 k ohm, Ta=20°C, RH=65%) SYMBOL
TEST CONDITION
Sensitivity
S
f=1kHz, Pin=1Pa
Impedance
Zout
f=1kHz, Pin=1Pa
MINIMUM
STANDARD
MAXIMUM
UNITS
-45
-42
-39
dB 0dB=1V/Pa
2.2
kΩ
0.5
mA
Directivity
OMNI-DIRECTIONAL
Current Consumption S/N Ratio
I S/N (A)
Sensitivity Reduction
∆S
f=1kHz, Pin=1Pa A Curve f=1kHz, Pin=1Pa Vs= 2.0 - 1.5
60
dB -3
Frequency Range
100-10,000
dB Hz
Frequency Response
Schematic Diagram of Circuit
II.
Mechanical Characteristics
Dimensions
∅
6 x 2.2
See Drawing in Section IV
Weight
Less than
Solderering Heat Shock
To be no interferance in operation after soldering temperature exposure at 260°C +/-5°C for 2 +/- 0.5 seconds.
Terminal Mechanical Strength
The soldering time must be less than 2 seconds each pad, and soldering pull must be larger than 0.5Kg each pad.
Absolute Maximum Ratings
0.2 g
Operating Voltage Vs (V) 10
Storage Temperature Operation Temperature Range Range Tope °C Tstg °C -40°C to +85°C
Issued Date:
2003/10/15
-25°C to +70°C
Version: A
PRODUCT SPECIFICATION III.
Reliability Tests
Doc: MB6022ASC-1
Note: After any of the following tests performed, the sensitivity of the microphone unit shall not deviate more than ±3dB from its initial value. The microphone shall maintain its initial operation and appearance. Measurements for tests with thermal requirements are to be done after 2hrs of condistioning at 20°C.
Vibration Test
The microphone to have no interferance in operation after vibrations, 10Hz to 55Hz for 1 minute full amplitude 1.52mm, for 2 hours at three axises.
Drop Test
The microphone unit must operate when dropped three times once on each axis from a height of 1m onto a metal plate.
Temperature Test
High
The microphone unit must operate within its sensitivity specifications after subjected to the following conditions: +80°C for 96 hrs, and exposed to room temperature for 2 hrs.
Low
The microphone unit must operate within its sensitivity specifications after subjected to the following conditions: -40°C for 96 hrs, and exposed to room temperature for 2 hrs.
Humidity Test
+70°C at 90%RH for 120 hrs
Temperature Cycle Test
After exposure at -40°C for 45 minutes, at+20°C for 10 minutes, at +85°C for 45 minutes, at +20°C for 10 minutes, 27 cycles. (The measurement to be done after 2 hrs of conditioning at +20°C.)
IV.
Dimensional Drawing
V.
Other
Better Shielded, RF noise resistant type.
The information contained in this literature is based on our experience to date and is believed to be reliable and it is subject to change without notice. It is intended as a guide for use by persons having technical skill at their own discretion and risk. We do not guarantee favorable results or assume any liability in connection with its use. Dimensions contained herein are for reference purposes only. For specific dimensional requirements consult factory. This publication is not to be taken as a license to operate under, or recommendation to infringe any existing patents. This supersedes and voids all previous literature.
Characteristics:Openning size 13mm*13mm,1m leading wire, standard Φ3.5 three-core plug output. voltage output type. Purposeï¼Used for current measurement ...
Jun 24, 2004 - row, 8 pixels tall, and the YAR corresponds to the display column, 1 pixel wide, of a particular byte. The most (least) significant bit, B7 (B0), ...
erogeneous attribute indices and equilibrium product differentiation is both horizontal and vertical. This new finding is relevant to describe many market situations. ... and Waterman in their book âIn Search of Excellenceâ (1982, p 171), ...
Aug 1, 2008 - LED (light emitting diode), uniform brightness, long lifetime (100 000 ...... hard during operation, some graphics will be abnormally displayed but ...
Aug 1, 2008 - Densitron low cost module ..... Data delay time ..... Inspect under 2x20W or 40W fluorescent lamp (approximately 3000 lux) leaving 25 .... Thermal Shock Test ... Do not wipe the display surface with dry or hard materials that will ...
UL Recognition Mark: UL Safety certification is identified with the UL File No. E139761 on ... 1008 K - 1024 K. FC000 - FFFFF. 16 KB ..... The ISA configuration utility can be downloaded from the Intel World Wide Web site (see Section 6.1).
The ISA configuration utility can be downloaded from the Intel World Wide Web site (see Section 6.1). ..... An * (asterisk) displayed next to an address indicates a.
Apr 24, 2008 - Electrical Characteristics . ..... JIS K7105. Note: Avoid operating with hard or sharp material such as a ball point pen or a mechanical.
Aug 26, 2013 - 13:30 - 15:00. O On the use of Location-based Services and Geofencing Concepts for Safety and Road Transport. Efficiency, A. Nait-Sidi-Moh, ...
1 045. 16 596 672. 6 050 563. 39 460. 1 775 000. 24 462 740. 39 548 630 .... lisations en fin d'exercice. 4. IMMOBILISATIONS. CO/. LV. MA. MD. MG. MJ. MM ..... chez l'entreprise investisseur dans le cadre de l'article 217 octies. RH. R. Ã. G.
1 Introduction ... be given by studying firms' choices of innovation when products are ... firms' decisions in terms of social welfare is also realized. ... When fixed costs depend on attributes, we use the classical linear ..... with the attributes
Your clothing may become caught by accidental contact with the rotating insertion tool which may then drill into your body. â« Regularly clean the ventilation slots.
Nov 11, 2017 - Choisy M. & Rohani P. (2012) Changing spatial epidemiology of pertussis in continental USA. Proc. R. Soc. B 279(1747): 4574-4581. Broutin V.
4th year project (Sup. J-M. Godart et A. ... Teaching. 2007. Course - Industrial risks management (4H). Responsible : Jean Baccou. Ms.c. degree .... on Principles and Methods of Statistical Inference with Interval Probability, Durham University.