Sherco Carb Jetting Instructions This manual provides instructions on how to remove and reinstall the stock carburetor, it also shows you how to change the pilot jet and the main jet. It is intended to be used for all Sherco 1.25 – 2.9 Trials Motorcycles. The motorcycle shown is a new 2002, 2.9, the one that you are working on may be slightly different but the principles shown will apply to all of the models indicated. The technician shown in the photographs is David Chaves who received his training at the Sherco factory in Spain. David is also a member of Team Sherco and is competing in the NATC national series as a Champ rider. If you have any question or are not certain about any procedure call Ryan Young Products on 1-800-6078742. 7/22/2002
Sherco Carb Jetting
1
www.shercousa.com
The First Step is to Remove the Rear Fender.
Remove the 2 rear fender mounting bolts.
Remove the front mounting bolt. 7/22/2002
Disconnect the taillight harness.
Sherco Carb Jetting
2
www.shercousa.com
The Second Step is to Remove the Fuel Tank
Remove the top fuel tank mounting bolt and disconnect the fuel overflow line and the fuel line.
Remove the airbox by removing the 3 mounting screws. 7/22/2002
Sherco Carb Jetting
3
www.shercousa.com
Air Box Removal Continued
Notice that David is loosening the rear clamp, the one that attaches the air box to the rubber manifold. Do not loosen the clamp that attaches the rubber manifold to the carburetor. 7/22/2002
Sherco Carb Jetting
4
www.shercousa.com
To facilitate the removal of the air box remove the fender retaining nut. Remove the air box and set it aside.
7/22/2002
Sherco Carb Jetting
5
www.shercousa.com
Slide Removal
Loosen the 2 screws that retain the carb slide, remove it and set it aside.
David hangs it over the side of the frame as shown. 7/22/2002
Sherco Carb Jetting
6
www.shercousa.com
Loosen the manifold clamp at the carburetor.
Remove the carburetor from the frame as shown. 7/22/2002
Sherco Carb Jetting
7
www.shercousa.com
Changing the Jets
Set the carburetor on a clean surface.
Use a 14 mm wrench and remove the main jet holder. 7/22/2002
Sherco Carb Jetting
8
www.shercousa.com
Main Jet
Main jet holder Set the float bowl upright as shown in order to keep the floats from falling out of the bowl.
7/22/2002
Sherco Carb Jetting
9
www.shercousa.com
To change the main jet hold it in a 14 mm box end wrench and use a straight screw driver that fits it tight, remove it and replace it with the appropriate one for your operating conditions.
The pilot jet is located in the body of the carburetor as shown, to change it use a straight screw driver that fits it tight, remove it and replace it with the appropriate one for your conditions. 7/22/2002
Sherco Carb Jetting
10
www.shercousa.com
Replacing the Float Bowl
Notice how David holds the carburetor body and the float bowl, this method insures that the floats do not fall out of the bowl.
Install and tighten the main jet holder. 7/22/2002
Sherco Carb Jetting
11
www.shercousa.com
The jets are changed and the carburetor is ready to be reinstalled. For the most part the assembly process is just the disassembly reversed. We will make note of a few things that David does to make the job go smoother.
7/22/2002
Sherco Carb Jetting
12
www.shercousa.com
Carburetor Installation Tips
David routes the fuel line under the engine breather line as shown. 7/22/2002
Sherco Carb Jetting
13
www.shercousa.com
Install the carb as shown.
7/22/2002
Sherco Carb Jetting
14
www.shercousa.com
Reinstall the slide, look to make sure that it is installed properly. David operates the throttle and makes sure that the slide is operating properly. This is CRITICAL, take your time and do this right.
7/22/2002
Sherco Carb Jetting
15
www.shercousa.com
David installs the air box and the fuel tank before he tightens the carburetor clamps. He does this so that he can rotate the carburetor in order to provide operating clearance for the choke lever.
7/22/2002
Sherco Carb Jetting
16
www.shercousa.com
Rotate the carburetor so that the choke lever operates properly. Now tighten the manifold clamps. 7/22/2002
Sherco Carb Jetting
17
www.shercousa.com
External Carburetor Adjustments
There are 2 screws that allow you to make adjustments to the carburetor, the one on the right is the idle adjustment screw and the one on the left is the “GAS” screw. Turning the idle screw in (clockwise), increases the idle speed, turning it out decreases the idle speed. Turning the “GAS” screw out (counter clockwise) makes the idle mixture richer and turning it in makes it leaner. 7/22/2002
Sherco Carb Jetting
18
www.shercousa.com
Tighten all the bolts, connect the fuel lines, install the rear fender and the bike is ready to be test ridden. If you have any questions or are not certain about any procedure call Ryan Young Products on 1-800-6078742. 7/22/2002
Sep 17, 2002 - â¢Take the time to check the tightness of these fasteners. â¢Tighten the ... We recommend Maxima Formula K2 Racing 2-cycle oil (available from. RYP) ..... Reinstall the foot peg mounting nut, the airbox and the rear finder and ...
This manual is designed to provide the Sherco owner with instructions on how ... Fork Parts Overview, 2003 Sherco Parts Book, p.32 .... Scribed line on the fork ...
gathered by them and must make independent determinations of suitability and completeness of ... Estimated lethal dose in humans -0.5-5.0 g/kg (based on.
First, let's go over some of the assets of the Posa: 1. Posa will run in any position, updraft, downdraft or sidedraft (the latter being by far the most common),.
Your Edelbrock Performer Series carburetor was calibrated using Edelbrock ... The following manual consists of 2 sections; Theory of Operation and Tuning ..... Edelbrock Street Fuel Pumps are highly recommended for all Edelbrock Performer.
cant changes in specifications or procedures will be forwarded to all authorized ...... Connecting rod bolts and nuts ...... â¢Make sure that the motorcycle is upright.
You are very lucky! Hungry & Thirsty. A: Bonjour! Comment vas-tu aujourd'hui? Hello! How are you today? B: Ãa va, merci! Est-ce que tu as faim? I'm fine, thanks ...
Jan 13, 2012 - DOWNLOADING, USING OR PROVIDING FEEDBACK ON THE MATERIALS, YOU AGREE TO THESE. TERMS. ...... partners.adobe.com/public/developer/en/tiff/TIFF6.pdf. ...... The offset vector can be used to adjust the position of a ...... Data="M 25,25 L
Jan 31, 2018 - in the analogous statement: âOne million lottery tickets were sold and Mr. X ..... might seem hardly enough to survive on, but on the other, certain ...
Students: Belgium performed above the OECD average in PISA 2015 in science, mathematics and reading, with performance variations among Communities. Overall average performance in mathematics decreased across PISA cycles, while average performance in
SMPTE Technology Committee N 26 on File Management and Networking Technology .... Each data stream shall have an interface frequency of 148.5 MHz or ...
biomedical research output, broken down into geographical ...... The number of high impact EBM articles for the 50 top ...... Proscizen Technologies P Ltd.