Philips/BenQ/LiteOn VAD6038 Firmware Tutorial Backing up and flashing the original firmware!! Please keep checking Xbox360 scene websites for updates. xboxhacker.net
xbox-scene.com
maxconsole.net
Now read this tutorial, twice. If you don’t understand any terms, ask questions in forums until you do!! You might as well make sure you have the right equipment to dump/flash your drive.
you will need: - soldering iron + tin - thin wire (0,08mm - to reconnect the trace) - scalpel or x-acto knife (to cut the trace) - switch (or use wires only) - Schtrom’s DosFlash (Download) read ReadMe.txt first!!
Good luck!!
There are two methods available, to set the Benq drive into recovery mode. Both do the same.
Method #1
(for beginners)
Cut these two traces (SPI power supply) and solder a simple switch (or wires) to the yellow locations. Set the switch to “Off”.
Method #2
(for advanced users)
Remove the white epoxy, cut the trace shown below (SPI pin1) and solder a simple switch (or wires) to blue locations.
Drive in original state:
Drive is not read- or flashable!
Choose you favorite method and prepare the logicboard.
Reading Firmware: Power on your PC and boot from USB-Stick or floppy disc into MS-DOS. (only real DOS) When you reach the DOS command prompt, plug the SATA cable into the Benq drive, so that the drive is connected to your PC mainboard or SATA card. (disconnect other HDDs and drives) Type "dosflash" to use the auto mode. (dont hit return yet) Now connect your drive to X360 with power cable and turn the xbox on. (switch is still in “Off” position) Then, one second later flip the VCC switch to “On”, and hit the enter key on your keyboard. Select the drive port, choose [R] command to backup the firmware and type the file name. (always have a look at the generated DataSum) It should look like this and reading your firmware!
Writing Firmware: Same way for updating the drive firmware. Power on your PC and boot from USB-Stick or floppy disc into MS-DOS. (only real DOS) When you reach the DOS command prompt, plug the SATA cable into the Benq drive, so that the drive is connected to your PC mainboard or SATA card. (disconnect other HDDs and drives) Type "dosflash" to use the auto mode. (dont hit return yet) Now connect your drive to X360 with power cable and turn the xbox on. (switch is still in “Off” position) Then one second later flip the VCC switch to “On”, and hit the enter key on your keyboard. Select the drive port, choose [W] command to update the firmware and type the file name. (always have a look at the generated DataSum) It should look like this and writing your firmware!
Produced and Edited by Team MODFREAKz Special thanks to Schtrom for his DosFlash Tool!! Many thanks to Tiros, uberfry, caster420 and TheXone
If you have never used Xbins before, the easiest method is to use. Ground Zero's automated Xbins downloader. Download. Download the self-extracting archive ...
Xbins is an IRC channel and. FTP server that hosts Xbox and ... The program will connect to the IRC channel, message the bot, and connect to the ...... Page 81 ...
The second security measure is media locking. The default.xex ... firmware modification or purchase two Xbox 360 systems. With that .... hacked firmware, it will give you the next instructions: ... needs to be kept safe! ..... Radioshack model.
Xbins is an IRC channel and. FTP server that hosts Xbox and Xbox ... The program will connect to the IRC channel, message the bot, and connect to ..... Page 38 ...
4 juin 2015 - Data Rate. 802.11b ... the instructions, may cause harmful interference to radio communications. ... safety nor interfere a legal communication, if.
This document contains confidential proprietary information and is property of LTC. The contents of this document should not be disclosed to unauthorized ...
installed such that 20cm may be maintained between the antenna and users. The final end .... WPA, WPA2, WPS, WEP 64b&128bit, IEEE 802.1X,. IEEE 802.11i.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE. STATEMENT. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecti
Firmware Update Procedures. Precaution. â A power failure during the firmware writing operation may disable the camera. ⢠Use a fully charged Battery Pack ...
Mar 15, 2010 - Depends on CPU type. - 18F2550 can be supplied with 5V or 3,6V. - 18F26K20 requires a 3.6V. Two diodes are used to drop from 5V to 3.6V.
802.11a/b/g/n/ac 2Tx2R USB Combo Module. WN4519L. User Manual .... This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. ... contact its test lab, TCB or LITE-ON to dete
This section gives the detailed entry and exit conditions and effects of the routines in the indirections jumpblock. See section 14.2 for a list of these routines.
tools: Work. Skills: Other conditions: I want to apply for. Save this job. (C510) MCU development tools, software / firmware engineer. Holtek Semiconductor Inc.
setting of the line mask determines how pixels on the line will be plotted. The line mask is bit significant and is used repeatedly in the order bit 7, bit 6 down to bit ...
Si jamais cet écran ne s'affiche pas, déconnectez la tablette, fermez le ... Pour vérifier que la mise à jour de soft a bien été faite, allez dans les « Paramètres ».
TUTORIAL. A quick guide that shows how to use the main features of the Java Novel Generator. 1. Ready to start. When you start the application, you should find ...
UIML language elements and structure. 2. Separation of ... This tutorial assumes that you are familier with Java AWT component names, attributes and layout. ... We want to put the message and button inside the dialog and arrange them vertically. ....
place several branches close to one another without damaging the mesh. This tutorial shows an example of an adaptive skin mesh made from a ZSphere model ...